Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

330 lines
12 KiB

/**
* Marlin 3D Printer Firmware
*
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com
* Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#include "../platforms.h"
#ifdef HAL_STM32
#include "../../inc/MarlinConfig.h"
// ------------------------
// Local defines
// ------------------------
// Default timer priorities. Override by specifying alternate priorities in the board pins file.
// The TONE timer is not present here, as it currently cannot be set programmatically. It is set
// by defining TIM_IRQ_PRIO in the variant.h or platformio.ini file, which adjusts the default
// priority for STM32 HardwareTimer objects.
#define SWSERIAL_TIMER_IRQ_PRIO_DEFAULT 1 // Requires tight bit timing to communicate reliably with TMC drivers
#define SERVO_TIMER_IRQ_PRIO_DEFAULT 1 // Requires tight PWM timing to control a BLTouch reliably
#define STEP_TIMER_IRQ_PRIO_DEFAULT 2
#define TEMP_TIMER_IRQ_PRIO_DEFAULT 14 // Low priority avoids interference with other hardware and timers
#ifndef STEP_TIMER_IRQ_PRIO
#define STEP_TIMER_IRQ_PRIO STEP_TIMER_IRQ_PRIO_DEFAULT
#endif
#ifndef TEMP_TIMER_IRQ_PRIO
#define TEMP_TIMER_IRQ_PRIO TEMP_TIMER_IRQ_PRIO_DEFAULT
#endif
#if HAS_TMC_SW_SERIAL
#include <SoftwareSerial.h>
#ifndef SWSERIAL_TIMER_IRQ_PRIO
#define SWSERIAL_TIMER_IRQ_PRIO SWSERIAL_TIMER_IRQ_PRIO_DEFAULT
#endif
#endif
#if HAS_SERVOS
#include "Servo.h"
#ifndef SERVO_TIMER_IRQ_PRIO
#define SERVO_TIMER_IRQ_PRIO SERVO_TIMER_IRQ_PRIO_DEFAULT
#endif
#endif
#if ENABLED(SPEAKER)
// Ensure the default timer priority is somewhere between the STEP and TEMP priorities.
// The STM32 framework defaults to interrupt 14 for all timers. This should be increased so that
// timing-sensitive operations such as speaker output are not impacted by the long-running
// temperature ISR. This must be defined in the platformio.ini file or the board's variant.h,
// so that it will be consumed by framework code.
#if !(TIM_IRQ_PRIO > STEP_TIMER_IRQ_PRIO && TIM_IRQ_PRIO < TEMP_TIMER_IRQ_PRIO)
#error "Default timer interrupt priority is unspecified or set to a value which may degrade performance."
#endif
#endif
#if defined(STM32F0xx) || defined(STM32G0xx)
#define MCU_STEP_TIMER 16
#define MCU_TEMP_TIMER 17
#elif defined(STM32F1xx)
#define MCU_STEP_TIMER 4
#define MCU_TEMP_TIMER 2
#elif defined(STM32F401xC) || defined(STM32F401xE)
#define MCU_STEP_TIMER 9
#define MCU_TEMP_TIMER 10
#elif defined(STM32F4xx) || defined(STM32F7xx) || defined(STM32H7xx)
#define MCU_STEP_TIMER 6 // STM32F401 has no TIM6, TIM7, or TIM8
#define MCU_TEMP_TIMER 14 // TIM7 is consumed by Software Serial if used.
#endif
#ifndef HAL_TIMER_RATE
#define HAL_TIMER_RATE GetStepperTimerClkFreq()
#endif
#ifndef STEP_TIMER
#define STEP_TIMER MCU_STEP_TIMER
#endif
#ifndef TEMP_TIMER
#define TEMP_TIMER MCU_TEMP_TIMER
#endif
#define __TIMER_DEV(X) TIM##X
#define _TIMER_DEV(X) __TIMER_DEV(X)
#define STEP_TIMER_DEV _TIMER_DEV(STEP_TIMER)
#define TEMP_TIMER_DEV _TIMER_DEV(TEMP_TIMER)
// --------------------------------------------------------------------------
// Local defines
// --------------------------------------------------------------------------
#define NUM_HARDWARE_TIMERS 2
// --------------------------------------------------------------------------
// Private Variables
// --------------------------------------------------------------------------
HardwareTimer *timer_instance[NUM_HARDWARE_TIMERS] = { nullptr };
// ------------------------
// Public functions
// ------------------------
uint32_t GetStepperTimerClkFreq() {
// Timer input clocks vary between devices, and in some cases between timers on the same device.
// Retrieve at runtime to ensure device compatibility. Cache result to avoid repeated overhead.
static uint32_t clkfreq = timer_instance[MF_TIMER_STEP]->getTimerClkFreq();
return clkfreq;
}
// frequency is in Hertz
void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) {
if (!HAL_timer_initialized(timer_num)) {
switch (timer_num) {
case MF_TIMER_STEP: // STEPPER TIMER - use a 32bit timer if possible
timer_instance[timer_num] = new HardwareTimer(STEP_TIMER_DEV);
/* Set the prescaler to the final desired value.
* This will change the effective ISR callback frequency but when
* HAL_timer_start(timer_num=0) is called in the core for the first time
* the real frequency isn't important as long as, after boot, the ISR
* gets called with the correct prescaler and count register. So here
* we set the prescaler to the correct, final value and ignore the frequency
* asked. We will call back the ISR in 1 second to start at full speed.
*
* The proper fix, however, would be a correct initialization OR a
* HAL_timer_change(const uint8_t timer_num, const uint32_t frequency)
* which changes the prescaler when an IRQ frequency change is needed
* (for example when steppers are turned on)
*/
timer_instance[timer_num]->setPrescaleFactor(STEPPER_TIMER_PRESCALE); //the -1 is done internally
timer_instance[timer_num]->setOverflow(_MIN(hal_timer_t(HAL_TIMER_TYPE_MAX), (HAL_TIMER_RATE) / (STEPPER_TIMER_PRESCALE) /* /frequency */), TICK_FORMAT);
break;
case MF_TIMER_TEMP: // TEMP TIMER - any available 16bit timer
timer_instance[timer_num] = new HardwareTimer(TEMP_TIMER_DEV);
// The prescale factor is computed automatically for HERTZ_FORMAT
timer_instance[timer_num]->setOverflow(frequency, HERTZ_FORMAT);
break;
}
// Disable preload. Leaving it default-enabled can cause the timer to stop if it happens
// to exit the ISR after the start time for the next interrupt has already passed.
timer_instance[timer_num]->setPreloadEnable(false);
HAL_timer_enable_interrupt(timer_num);
// Start the timer.
timer_instance[timer_num]->resume(); // First call to resume() MUST follow the attachInterrupt()
// This is fixed in Arduino_Core_STM32 1.8.
// These calls can be removed and replaced with
// timer_instance[timer_num]->setInterruptPriority
switch (timer_num) {
case MF_TIMER_STEP:
timer_instance[timer_num]->setInterruptPriority(STEP_TIMER_IRQ_PRIO, 0);
break;
case MF_TIMER_TEMP:
timer_instance[timer_num]->setInterruptPriority(TEMP_TIMER_IRQ_PRIO, 0);
break;
}
}
}
void HAL_timer_enable_interrupt(const uint8_t timer_num) {
if (HAL_timer_initialized(timer_num) && !timer_instance[timer_num]->hasInterrupt()) {
switch (timer_num) {
case MF_TIMER_STEP:
timer_instance[timer_num]->attachInterrupt(Step_Handler);
break;
case MF_TIMER_TEMP:
timer_instance[timer_num]->attachInterrupt(Temp_Handler);
break;
}
}
}
void HAL_timer_disable_interrupt(const uint8_t timer_num) {
if (HAL_timer_initialized(timer_num)) timer_instance[timer_num]->detachInterrupt();
}
bool HAL_timer_interrupt_enabled(const uint8_t timer_num) {
return HAL_timer_initialized(timer_num) && timer_instance[timer_num]->hasInterrupt();
}
void SetTimerInterruptPriorities() {
TERN_(HAS_TMC_SW_SERIAL, SoftwareSerial::setInterruptPriority(SWSERIAL_TIMER_IRQ_PRIO, 0));
TERN_(HAS_SERVOS, libServo::setInterruptPriority(SERVO_TIMER_IRQ_PRIO, 0));
}
// ------------------------
// Detect timer conflicts
// ------------------------
// This list serves two purposes. Firstly, it facilitates build-time mapping between
// variant-defined timer names (such as TIM1) and timer numbers. It also replicates
// the order of timers used in the framework's SoftwareSerial.cpp. The first timer in
// this list will be automatically used by SoftwareSerial if it is not already defined
// in the board's variant or compiler options.
static constexpr struct {uintptr_t base_address; int timer_number;} stm32_timer_map[] = {
#ifdef TIM18_BASE
{ uintptr_t(TIM18), 18 },
#endif
#ifdef TIM7_BASE
{ uintptr_t(TIM7), 7 },
#endif
#ifdef TIM6_BASE
{ uintptr_t(TIM6), 6 },
#endif
#ifdef TIM22_BASE
{ uintptr_t(TIM22), 22 },
#endif
#ifdef TIM21_BASE
{ uintptr_t(TIM21), 21 },
#endif
#ifdef TIM17_BASE
{ uintptr_t(TIM17), 17 },
#endif
#ifdef TIM16_BASE
{ uintptr_t(TIM16), 16 },
#endif
#ifdef TIM15_BASE
{ uintptr_t(TIM15), 15 },
#endif
#ifdef TIM14_BASE
{ uintptr_t(TIM14), 14 },
#endif
#ifdef TIM13_BASE
{ uintptr_t(TIM13), 13 },
#endif
#ifdef TIM11_BASE
{ uintptr_t(TIM11), 11 },
#endif
#ifdef TIM10_BASE
{ uintptr_t(TIM10), 10 },
#endif
#ifdef TIM12_BASE
{ uintptr_t(TIM12), 12 },
#endif
#ifdef TIM19_BASE
{ uintptr_t(TIM19), 19 },
#endif
#ifdef TIM9_BASE
{ uintptr_t(TIM9), 9 },
#endif
#ifdef TIM5_BASE
{ uintptr_t(TIM5), 5 },
#endif
#ifdef TIM4_BASE
{ uintptr_t(TIM4), 4 },
#endif
#ifdef TIM3_BASE
{ uintptr_t(TIM3), 3 },
#endif
#ifdef TIM2_BASE
{ uintptr_t(TIM2), 2 },
#endif
#ifdef TIM20_BASE
{ uintptr_t(TIM20), 20 },
#endif
#ifdef TIM8_BASE
{ uintptr_t(TIM8), 8 },
#endif
#ifdef TIM1_BASE
{ uintptr_t(TIM1), 1 }
#endif
};
// Convert from a timer base address to its integer timer number.
static constexpr int get_timer_num_from_base_address(uintptr_t base_address) {
for (const auto &timer : stm32_timer_map)
if (timer.base_address == base_address) return timer.timer_number;
return 0;
}
// The platform's SoftwareSerial.cpp will use the first timer from stm32_timer_map.
#if HAS_TMC_SW_SERIAL && !defined(TIMER_SERIAL)
#define TIMER_SERIAL (stm32_timer_map[0].base_address)
#endif
// constexpr doesn't like using the base address pointers that timers evaluate to.
// We can get away with casting them to uintptr_t, if we do so inside an array.
// GCC will not currently do it directly to a uintptr_t.
IF_ENABLED(HAS_TMC_SW_SERIAL, static constexpr uintptr_t timer_serial[] = {uintptr_t(TIMER_SERIAL)});
IF_ENABLED(SPEAKER, static constexpr uintptr_t timer_tone[] = {uintptr_t(TIMER_TONE)});
IF_ENABLED(HAS_SERVOS, static constexpr uintptr_t timer_servo[] = {uintptr_t(TIMER_SERVO)});
enum TimerPurpose { TP_SERIAL, TP_TONE, TP_SERVO, TP_STEP, TP_TEMP };
// List of timers, to enable checking for conflicts.
// Includes the purpose of each timer to ease debugging when evaluating at build-time.
// This cannot yet account for timers used for PWM output, such as for fans.
static constexpr struct { TimerPurpose p; int t; } timers_in_use[] = {
#if HAS_TMC_SW_SERIAL
{TP_SERIAL, get_timer_num_from_base_address(timer_serial[0])}, // Set in variant.h, or as a define in platformio.h if not present in variant.h
#endif
#if ENABLED(SPEAKER)
{TP_TONE, get_timer_num_from_base_address(timer_tone[0])}, // Set in variant.h, or as a define in platformio.h if not present in variant.h
#endif
#if HAS_SERVOS
{TP_SERVO, get_timer_num_from_base_address(timer_servo[0])}, // Set in variant.h, or as a define in platformio.h if not present in variant.h
#endif
{TP_STEP, STEP_TIMER},
{TP_TEMP, TEMP_TIMER},
};
static constexpr bool verify_no_timer_conflicts() {
LOOP_L_N(i, COUNT(timers_in_use))
LOOP_S_L_N(j, i + 1, COUNT(timers_in_use))
if (timers_in_use[i].t == timers_in_use[j].t) return false;
return true;
}
// If this assertion fails at compile time, review the timers_in_use array.
// If default_envs is defined properly in platformio.ini, VS Code can evaluate the array
// when hovering over it, making it easy to identify the conflicting timers.
static_assert(verify_no_timer_conflicts(), "One or more timer conflict detected. Examine \"timers_in_use\" to help identify conflict.");
#endif // HAL_STM32