Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

694 lines
20 KiB

#ifndef PINS_H
#define PINS_H
/****************************************************************************************
* Arduino pin assignment
*
* ATMega168
* +-\/-+
* PC6 1| |28 PC5 (AI 5 / D19)
* (D 0) PD0 2| |27 PC4 (AI 4 / D18)
* (D 1) PD1 3| |26 PC3 (AI 3 / D17)
* (D 2) PD2 4| |25 PC2 (AI 2 / D16)
* PWM+ (D 3) PD3 5| |24 PC1 (AI 1 / D15)
* (D 4) PD4 6| |23 PC0 (AI 0 / D14)
* VCC 7| |22 GND
* GND 8| |21 AREF
* PB6 9| |20 AVCC
* PB7 10| |19 PB5 (D 13)
* PWM+ (D 5) PD5 11| |18 PB4 (D 12)
* PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM
* (D 7) PD7 13| |16 PB2 (D 10) PWM
* (D 8) PB0 14| |15 PB1 (D 9) PWM
* +----+
****************************************************************************************/
#if MOTHERBOARD == 0
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega168__
#error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu.
#endif
#define X_STEP_PIN 2
#define X_DIR_PIN 3
#define X_ENABLE_PIN -1
#define X_MIN_PIN 4
#define X_MAX_PIN 9
#define Y_STEP_PIN 10
#define Y_DIR_PIN 7
#define Y_ENABLE_PIN -1
#define Y_MIN_PIN 8
#define Y_MAX_PIN 13
#define Z_STEP_PIN 19
#define Z_DIR_PIN 18
#define Z_ENABLE_PIN 5
#define Z_MIN_PIN 17
#define Z_MAX_PIN 16
#define E_STEP_PIN 11
#define E_DIR_PIN 12
#define E_ENABLE_PIN -1
#define SDPOWER -1
#define SDSS -1
#define LED_PIN -1
#define FAN_PIN -1
#define PS_ON_PIN 15
#define KILL_PIN -1
#define HEATER_0_PIN 6
#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#endif
/****************************************************************************************
* Sanguino/RepRap Motherboard with direct-drive extruders
*
* ATMega644P
*
* +---\/---+
* (D 0) PB0 1| |40 PA0 (AI 0 / D31)
* (D 1) PB1 2| |39 PA1 (AI 1 / D30)
* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
* RST 9| |32 AREF
* VCC 10| |31 GND
* GND 11| |30 AVCC
* XTAL2 12| |29 PC7 (D 23)
* XTAL1 13| |28 PC6 (D 22)
* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
* +--------+
*
****************************************************************************************/
#if MOTHERBOARD == 1
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 15
#define X_DIR_PIN 18
#define X_ENABLE_PIN 19
#define X_MIN_PIN 20
#define X_MAX_PIN 21
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 19
#define Y_MIN_PIN 25
#define Y_MAX_PIN 26
#define Z_STEP_PIN 29
#define Z_DIR_PIN 30
#define Z_ENABLE_PIN 31
#define Z_MIN_PIN 2
#define Z_MAX_PIN 1
#define E_STEP_PIN 12
#define E_DIR_PIN 16
#define E_ENABLE_PIN 3
#define SDPOWER -1
#define SDSS -1
#define LED_PIN 0
#define FAN_PIN -1
#define PS_ON_PIN -1
#define KILL_PIN -1
#define HEATER_0_PIN 14
#define TEMP_0_PIN 4 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
#endif
/****************************************************************************************
* RepRap Motherboard ****---NOOOOOO RS485/EXTRUDER CONTROLLER!!!!!!!!!!!!!!!!!---*******
*
****************************************************************************************/
#if MOTHERBOARD == 2
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 15
#define X_DIR_PIN 18
#define X_ENABLE_PIN 19
#define X_MIN_PIN 20
#define X_MAX_PIN 21
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Y_MIN_PIN 25
#define Y_MAX_PIN 26
#define Z_STEP_PINN 27
#define Z_DIR_PINN 28
#define Z_ENABLE_PIN 29
#define Z_MIN_PIN 30
#define Z_MAX_PIN 31
#define E_STEP_PIN 17
#define E_DIR_PIN 16
#define E_ENABLE_PIN -1
#define SDPOWER -1
#define SDSS 4
#define LED_PIN 0
#define SD_CARD_WRITE 2
#define SD_CARD_DETECT 3
#define SD_CARD_SELECT 4
//our RS485 pins
#define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13
//pin for controlling the PSU.
#define PS_ON_PIN 14
#define FAN_PIN -1
#define KILL_PIN -1
#define HEATER_0_PIN -1
#define TEMP_0_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#endif
/****************************************************************************************
* Arduino Mega pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 33
#define MOTHERBOARD 3
#define RAMPS_V_1_3
#endif
#if MOTHERBOARD == 3
#define KNOWN_BOARD 1
//////////////////FIX THIS//////////////
#ifndef __AVR_ATmega1280__
#ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif
#endif
// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1
// #define RAMPS_V_1_3
// #define RAMPS_V_1_0
#ifdef RAMPS_V_1_3
#define X_STEP_PIN 54
#define X_DIR_PIN 55
#define X_ENABLE_PIN 38
#define X_MIN_PIN 3
#define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable.
#define Y_STEP_PIN 60
#define Y_DIR_PIN 61
#define Y_ENABLE_PIN 56
#define Y_MIN_PIN 14
#define Y_MAX_PIN -1 //15
#define Z_STEP_PIN 46
#define Z_DIR_PIN 48
#define Z_ENABLE_PIN 62
#define Z_MIN_PIN 18
#define Z_MAX_PIN -1 //19
#define E_STEP_PIN 26
#define E_DIR_PIN 28
#define E_ENABLE_PIN 24
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#define FAN_PIN 9
#define PS_ON_PIN 12
#define KILL_PIN -1
#define HEATER_0_PIN 10
#define HEATER_1_PIN 8
#define HEATER_2_PIN -1
#define TEMP_0_PIN 13 // ANALOG NUMBERING
#define TEMP_1_PIN 14 // ANALOG NUMBERING
#define TEMP_2_PIN -1 // ANALOG NUMBERING
#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default
#define X_STEP_PIN 26
#define X_DIR_PIN 28
#define X_ENABLE_PIN 24
#define X_MIN_PIN 3
#define X_MAX_PIN -1 //2
#define Y_STEP_PIN 38
#define Y_DIR_PIN 40
#define Y_ENABLE_PIN 36
#define Y_MIN_PIN 16
#define Y_MAX_PIN -1 //17
#define Z_STEP_PIN 44
#define Z_DIR_PIN 46
#define Z_ENABLE_PIN 42
#define Z_MIN_PIN 18
#define Z_MAX_PIN -1 //19
#define E_STEP_PIN 32
#define E_DIR_PIN 34
#define E_ENABLE_PIN 30
#define SDPOWER 48
#define SDSS 53
#define LED_PIN 13
#define PS_ON_PIN -1
#define KILL_PIN -1
#ifdef RAMPS_V_1_0 // RAMPS_V_1_0
#define HEATER_0_PIN 12 // RAMPS 1.0
#define HEATER_1_PIN -1 // RAMPS 1.0
#define FAN_PIN 11 // RAMPS 1.0
#else // RAMPS_V_1_1 or RAMPS_V_1_2
#define HEATER_0_PIN 10 // RAMPS 1.1
#define HEATER_1_PIN 8 // RAMPS 1.1
#define FAN_PIN 9 // RAMPS 1.1
#endif
#define HEATER_2_PIN -1
#define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define TEMP_2_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#endif
// SPI for Max6675 Thermocouple
#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support #define SCK_PIN 52
#define MISO_PIN 50
#define MOSI_PIN 51
#define MAX6675_SS 53
#else
#define MAX6675_SS 49
#endif
#endif
/****************************************************************************************
* Duemilanove w/ ATMega328P pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 4
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega328P__
#error Oops! Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 19
#define X_DIR_PIN 18
#define X_ENABLE_PIN -1
#define X_MIN_PIN 17
#define X_MAX_PIN -1
#define Y_STEP_PIN 10
#define Y_DIR_PIN 7
#define Y_ENABLE_PIN -1
#define Y_MIN_PIN 8
#define Y_MAX_PIN -1
#define Z_STEP_PIN 13
#define Z_DIR_PIN 3
#define Z_ENABLE_PIN 2
#define Z_MIN_PIN 4
#define Z_MAX_PIN -1
#define E_STEP_PIN 11
#define E_DIR_PIN 12
#define E_ENABLE_PIN -1
#define SDPOWER -1
#define SDSS -1
#define LED_PIN -1
#define FAN_PIN 5
#define PS_ON_PIN -1
#define KILL_PIN -1
#define HEATER_0_PIN 6
#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#endif
/****************************************************************************************
* Gen6 pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 5
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
//x axis pins
#define X_STEP_PIN 15
#define X_DIR_PIN 18
#define X_ENABLE_PIN 19
#define X_MIN_PIN 20
#define X_MAX_PIN -1
//y axis pins
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Y_MIN_PIN 25
#define Y_MAX_PIN -1
//z axis pins
#define Z_STEP_PIN 27
#define Z_DIR_PIN 28
#define Z_ENABLE_PIN 29
#define Z_MIN_PIN 30
#define Z_MAX_PIN -1
//extruder pins
#define E_STEP_PIN 4 //Edited @ EJE Electronics 20100715
#define E_DIR_PIN 2 //Edited @ EJE Electronics 20100715
#define E_ENABLE_PIN 3 //Added @ EJE Electronics 20100715
#define TEMP_0_PIN 5 //changed @ rkoeppl 20110410
#define HEATER_0_PIN 14 //changed @ rkoeppl 20110410
#define HEATER_1_PIN -1 //changed @ rkoeppl 20110410
#define HEATER_2_PIN -1
#define SDPOWER -1
#define SDSS 17
#define LED_PIN -1 //changed @ rkoeppl 20110410
#define TEMP_1_PIN -1 //changed @ rkoeppl 20110410
#define TEMP_2_PIN -1
#define FAN_PIN -1 //changed @ rkoeppl 20110410
#define PS_ON_PIN -1 //changed @ rkoeppl 20110410
//our pin for debugging.
#define DEBUG_PIN 0
//our RS485 pins
#define TX_ENABLE_PIN 12
#define RX_ENABLE_PIN 13
#endif
/****************************************************************************************
* Sanguinololu pin assignment
*
****************************************************************************************/
#if MOTHERBOARD == 62
#define MOTHERBOARD 6
#define SANGUINOLOLU_V_1_2
#endif
#if MOTHERBOARD == 6
#define KNOWN_BOARD 1
#ifndef __AVR_ATmega644P__
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
#endif
#define X_STEP_PIN 15
#define X_DIR_PIN 21
#define X_MIN_PIN 18
#define X_MAX_PIN -2
#define Y_STEP_PIN 22
#define Y_DIR_PIN 23
#define Y_MIN_PIN 19
#define Y_MAX_PIN -1
#define Z_STEP_PIN 3
#define Z_DIR_PIN 2
#define Z_MIN_PIN 20
#define Z_MAX_PIN -1
#define E_STEP_PIN 1
#define E_DIR_PIN 0
#define LED_PIN -1
#define FAN_PIN -1
#define PS_ON_PIN -1
#define KILL_PIN -1
#define HEATER_0_PIN 13 // (extruder)
#ifdef SANGUINOLOLU_V_1_2
#define HEATER_1_PIN 12 // (bed)
#define X_ENABLE_PIN 14
#define Y_ENABLE_PIN 14
#define Z_ENABLE_PIN 26
#define E_ENABLE_PIN 14
#else
#define HEATER_1_PIN 14 // (bed)
#define X_ENABLE_PIN -1
#define Y_ENABLE_PIN -1
#define Z_ENABLE_PIN -1
#define E_ENABLE_PIN -1
#endif
#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
#define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define TEMP_2_PIN -1
#define SDPOWER -1
#define SDSS 31
#define HEATER_2_PIN -1
#endif
#if MOTHERBOARD == 7
#define KNOWN_BOARD
/*****************************************************************
* Ultimaker pin assignment
******************************************************************/
#ifndef __AVR_ATmega1280__
#ifndef __AVR_ATmega2560__
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif
#endif
#define X_STEP_PIN 25
#define X_DIR_PIN 23
#define X_MIN_PIN 22
#define X_MAX_PIN 24
#define X_ENABLE_PIN 27
#define Y_STEP_PIN 31
#define Y_DIR_PIN 33
#define Y_MIN_PIN 26
#define Y_MAX_PIN 28
#define Y_ENABLE_PIN 29
#define Z_STEP_PIN 37
#define Z_DIR_PIN 39
#define Z_MIN_PIN 30
#define Z_MAX_PIN 32
#define Z_ENABLE_PIN 35
#define HEATER_1_PIN 4
#define TEMP_1_PIN 11
#define EXTRUDER_0_STEP_PIN 43
#define EXTRUDER_0_DIR_PIN 45
#define EXTRUDER_0_ENABLE_PIN 41
#define HEATER_0_PIN 2
#define TEMP_0_PIN 8
#define EXTRUDER_1_STEP_PIN 49
#define EXTRUDER_1_DIR_PIN 47
#define EXTRUDER_1_ENABLE_PIN 51
#define EXTRUDER_1_HEATER_PIN 3
#define EXTRUDER_1_TEMPERATURE_PIN 10
#define HEATER_2_PIN 51
#define TEMP_2_PIN 3
#define E_STEP_PIN EXTRUDER_0_STEP_PIN
#define E_DIR_PIN EXTRUDER_0_DIR_PIN
#define E_ENABLE_PIN EXTRUDER_0_ENABLE_PIN
#define SDPOWER -1
#define SDSS 53
#define LED_PIN 13
#define FAN_PIN 7
#define PS_ON_PIN 12
#define KILL_PIN -1
#ifdef ULTRA_LCD
#ifdef NEWPANEL
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 16
#define LCD_PINS_D5 21
#define LCD_PINS_D6 5
#define LCD_PINS_D7 6
//buttons are directly attached
#define BTN_EN1 40
#define BTN_EN2 42
#define BTN_ENC 19 //the click
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT 38
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
#else //old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
//buttons are attached to a shift register
#define SHIFT_CLK 38
#define SHIFT_LD 42
#define SHIFT_OUT 40
#define SHIFT_EN 17
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 5
#define LCD_PINS_D4 6
#define LCD_PINS_D5 21
#define LCD_PINS_D6 20
#define LCD_PINS_D7 19
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
//bits in the shift register that carry the buttons for:
// left up center down right red
#define BL_LE 7
#define BL_UP 6
#define BL_MI 5
#define BL_DW 4
#define BL_RI 3
#define BL_ST 2
#define BLEN_B 1
#define BLEN_A 0
#endif
#endif //ULTRA_LCD
#endif
/****************************************************************************************
* Teensylu 0.7 pin assingments (ATMEGA90USB)
* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE!
****************************************************************************************/
#if MOTHERBOARD == 8
#define MOTHERBOARD 8
#define KNOWN_BOARD 1
#define X_STEP_PIN 0
#define X_DIR_PIN 1
#define X_ENABLE_PIN 39
#define X_MIN_PIN 13
#define X_MAX_PIN -1
#define Y_STEP_PIN 2
#define Y_DIR_PIN 3
#define Y_ENABLE_PIN 38
#define Y_MIN_PIN 14
#define Y_MAX_PIN -1
#define Z_STEP_PIN 4
#define Z_DIR_PIN 5
#define Z_ENABLE_PIN 23
#define Z_MIN_PIN 15
#define Z_MAX_PIN -1
#define E_STEP_PIN 6
#define E_DIR_PIN 7
#define E_ENABLE_PIN 19
#define HEATER_0_PIN 21 // Extruder
#define HEATER_1_PIN 20 // Bed
#define HEATER_2_PIN -1
#define FAN_PIN 22 // Fan
#define TEMP_0_PIN 7 // Extruder
#define TEMP_1_PIN 6 // Bed
#define TEMP_2_PIN -1
#define SDPOWER -1
#define SDSS 8
#define LED_PIN -1
#define PS_ON_PIN -1
#define KILL_PIN -1
#define ALARM_PIN -1
#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
#define SCK_PIN 9
#define MISO_PIN 11
#define MOSI_PIN 10
#endif
#endif
#ifndef KNOWN_BOARD
#error Unknown MOTHERBOARD value in configuration.h
#endif
//List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, E_STEP_PIN, E_DIR_PIN, E_ENABLE_PIN, LED_PIN, PS_ON_PIN, HEATER_0_PIN, HEATER_1_PIN, HEATER_2_PIN, FAN_PIN, TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN}
#endif