You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
102 lines
3.1 KiB
102 lines
3.1 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
/**
|
|
* Platform-independent Arduino functions for I2C EEPROM.
|
|
* Enable USE_SHARED_EEPROM if not supplied by the framework.
|
|
*/
|
|
|
|
#include "../../inc/MarlinConfig.h"
|
|
|
|
#if ENABLED(I2C_EEPROM)
|
|
|
|
#include "eeprom_if.h"
|
|
|
|
#if ENABLED(SOFT_I2C_EEPROM)
|
|
#include <SlowSoftWire.h>
|
|
SlowSoftWire Wire = SlowSoftWire(I2C_SDA_PIN, I2C_SCL_PIN, true);
|
|
#else
|
|
#include <Wire.h>
|
|
#endif
|
|
|
|
void eeprom_init() {
|
|
Wire.begin(
|
|
#if PINS_EXIST(I2C_SCL, I2C_SDA) && DISABLED(SOFT_I2C_EEPROM)
|
|
uint8_t(I2C_SDA_PIN), uint8_t(I2C_SCL_PIN)
|
|
#endif
|
|
);
|
|
}
|
|
|
|
#if ENABLED(USE_SHARED_EEPROM)
|
|
|
|
#ifndef EEPROM_WRITE_DELAY
|
|
#define EEPROM_WRITE_DELAY 5
|
|
#endif
|
|
#ifndef EEPROM_DEVICE_ADDRESS
|
|
#define EEPROM_DEVICE_ADDRESS 0x50
|
|
#endif
|
|
|
|
static constexpr uint8_t eeprom_device_address = I2C_ADDRESS(EEPROM_DEVICE_ADDRESS);
|
|
|
|
// ------------------------
|
|
// Public functions
|
|
// ------------------------
|
|
|
|
#define SMALL_EEPROM (MARLIN_EEPROM_SIZE <= 2048)
|
|
|
|
// Combine Address high bits into the device address on <=16Kbit (2K) and >512Kbit (64K) EEPROMs.
|
|
// Note: MARLIN_EEPROM_SIZE is specified in bytes, whereas EEPROM model numbers refer to bits.
|
|
// e.g., The "16" in BL24C16 indicates a 16Kbit (2KB) size.
|
|
static uint8_t _eeprom_calc_device_address(uint8_t * const pos) {
|
|
const unsigned eeprom_address = (unsigned)pos;
|
|
return (SMALL_EEPROM || MARLIN_EEPROM_SIZE > 65536)
|
|
? uint8_t(eeprom_device_address | ((eeprom_address >> (SMALL_EEPROM ? 8 : 16)) & 0x07))
|
|
: eeprom_device_address;
|
|
}
|
|
|
|
static void _eeprom_begin(uint8_t * const pos) {
|
|
const unsigned eeprom_address = (unsigned)pos;
|
|
Wire.beginTransmission(_eeprom_calc_device_address(pos));
|
|
if (!SMALL_EEPROM)
|
|
Wire.write(uint8_t((eeprom_address >> 8) & 0xFF)); // Address High, if needed
|
|
Wire.write(uint8_t(eeprom_address & 0xFF)); // Address Low
|
|
}
|
|
|
|
void eeprom_write_byte(uint8_t *pos, uint8_t value) {
|
|
_eeprom_begin(pos);
|
|
Wire.write(value);
|
|
Wire.endTransmission();
|
|
|
|
// wait for write cycle to complete
|
|
// this could be done more efficiently with "acknowledge polling"
|
|
delay(EEPROM_WRITE_DELAY);
|
|
}
|
|
|
|
uint8_t eeprom_read_byte(uint8_t *pos) {
|
|
_eeprom_begin(pos);
|
|
Wire.endTransmission();
|
|
Wire.requestFrom(_eeprom_calc_device_address(pos), (byte)1);
|
|
return Wire.available() ? Wire.read() : 0xFF;
|
|
}
|
|
|
|
#endif // USE_SHARED_EEPROM
|
|
#endif // I2C_EEPROM
|
|
|