You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
130 lines
4.0 KiB
130 lines
4.0 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* Arduino Mega with RAMPS v1.4 adjusted pin assignments
|
|
*
|
|
* MKS GEN v1.3 (Extruder, Fan, Bed)
|
|
* MKS GEN v1.3 (Extruder, Extruder, Fan, Bed)
|
|
* MKS GEN v1.4 (Extruder, Fan, Bed)
|
|
* MKS GEN v1.4 (Extruder, Extruder, Fan, Bed)
|
|
*/
|
|
|
|
#if HOTENDS > 2 || E_STEPPERS > 2
|
|
#error "MKS GEN 1.3/1.4 supports up to 2 hotends / E-steppers. Comment out this line to continue."
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "MKS GEN >= v1.3"
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
// Power outputs EFBF or EFBE
|
|
#define MOSFET_D_PIN 7
|
|
|
|
//
|
|
// PSU / SERVO
|
|
//
|
|
// If PSU_CONTROL is specified, always hijack Servo 3
|
|
//
|
|
#if ENABLED(PSU_CONTROL)
|
|
#define SERVO3_PIN -1
|
|
#define PS_ON_PIN 4
|
|
#endif
|
|
|
|
#include "pins_RAMPS.h"
|
|
|
|
#undef EXP2_03_PIN
|
|
#define EXP2_03_PIN -1 // RESET
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if ANY(VIKI2, miniVIKI)
|
|
/**
|
|
* VIKI2 Has two groups of wires with...
|
|
*
|
|
* +Vin + Input supply, requires 120ma for LCD and mSD card
|
|
* GND Ground Pin
|
|
* MOSI Data input for LCD and SD
|
|
* MISO Data output for SD
|
|
* SCK Clock for LCD and SD
|
|
* AO Reg. Sel for LCD
|
|
* LCS Chip Select for LCD
|
|
* SDCS Chip Select for SD
|
|
* SDCD Card Detect pin for SD
|
|
* ENCA Encoder output A
|
|
* ENCB Encoder output B
|
|
* ENCBTN Encoder button switch
|
|
*
|
|
* BTN Panel mounted button switch
|
|
* BUZZER Piezo buzzer
|
|
* BLUE-LED Blue LED ring pin (3 to 5v, mosfet buffered)
|
|
* RED-LED Red LED ring pin (3 to 5v, mosfet buffered)
|
|
*
|
|
* This configuration uses the following arrangement:
|
|
*
|
|
* ------ ------
|
|
* ENCB |10 9 | ENCA MISO |10 9 | SCK
|
|
* BLUE_LED | 8 7 | RED_LED ENCBTN | 8 7 | SDCS
|
|
* KILL 6 5 | BEEPER 6 5 | MOSI
|
|
* A0 | 4 3 | LCD_CS SDCD | 4 3 |
|
|
* GND | 2 1 | 5V GND | 2 1 | --
|
|
* ------ ------
|
|
* EXP1 EXP2
|
|
*/
|
|
#undef SD_DETECT_PIN
|
|
#undef BTN_EN1
|
|
#undef BTN_EN2
|
|
#undef BTN_ENC
|
|
#undef DOGLCD_A0
|
|
#undef DOGLCD_CS
|
|
#undef BEEPER_PIN
|
|
#undef KILL_PIN
|
|
#undef STAT_LED_RED_PIN
|
|
#undef STAT_LED_BLUE_PIN
|
|
|
|
//
|
|
// VIKI2 12-wire lead
|
|
//
|
|
#define SD_DETECT_PIN EXP2_04_PIN // SDCD orange/white
|
|
#define BTN_EN1 EXP1_09_PIN // ENCA white
|
|
#define BTN_EN2 EXP1_10_PIN // ENCB green
|
|
#define BTN_ENC EXP2_08_PIN // ENCBTN purple
|
|
#define DOGLCD_A0 EXP1_04_PIN // A0 brown
|
|
#define DOGLCD_CS EXP1_03_PIN // LCS green/white
|
|
|
|
// EXP2_10_PIN gray MISO
|
|
// EXP2_05_PIN yellow MOSI
|
|
// EXP2_09_PIN orange SCK
|
|
|
|
//#define SDSS EXP2_07_PIN // SDCS blue
|
|
|
|
//
|
|
// VIKI2 4-wire lead
|
|
//
|
|
#define KILL_PIN EXP1_06_PIN // BTN blue
|
|
#define BEEPER_PIN EXP1_05_PIN // BUZZER green
|
|
#define STAT_LED_RED_PIN EXP1_07_PIN // RED-LED yellow
|
|
#define STAT_LED_BLUE_PIN EXP1_08_PIN // BLUE-LED white
|
|
#endif
|
|
|