You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
328 lines
11 KiB
328 lines
11 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* FLSUN HiSpeed V1 (STM32F103VET6) board pin assignments
|
|
* FLSun Hispeed (clone MKS_Robin_miniV2) board.
|
|
*
|
|
* MKS Robin Mini USB uses UART3 (PB10-TX, PB11-RX)
|
|
* #define SERIAL_PORT_2 3
|
|
*/
|
|
|
|
#if NOT_TARGET(__STM32F1__, STM32F1xx)
|
|
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
|
|
#elif HOTENDS > 1 || E_STEPPERS > 1
|
|
#error "FLSUN HiSpeedV1 only supports one hotend / E-stepper. Comment out this line to continue."
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "FLSun HiSpeedV1"
|
|
#define BOARD_WEBSITE_URL "github.com/Foxies-CSTL"
|
|
|
|
#define BOARD_NO_NATIVE_USB
|
|
|
|
// Avoid conflict with TIMER_SERVO when using the STM32 HAL
|
|
#define TEMP_TIMER 5
|
|
|
|
//
|
|
// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
|
|
//
|
|
#define DISABLE_DEBUG
|
|
|
|
//
|
|
// EEPROM
|
|
//
|
|
#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
|
|
#define FLASH_EEPROM_EMULATION
|
|
#define EEPROM_PAGE_SIZE (0x800U) // 2KB
|
|
#define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
|
|
#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2KB
|
|
#endif
|
|
|
|
//
|
|
// SPI
|
|
// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
|
|
//
|
|
#define SD_SCK_PIN PB13 // SPI2
|
|
#define SD_MISO_PIN PB14 // SPI2
|
|
#define SD_MOSI_PIN PB15 // SPI2
|
|
#define SPI_DEVICE 2
|
|
|
|
// SPI Flash
|
|
#define HAS_SPI_FLASH 1
|
|
#if HAS_SPI_FLASH
|
|
// SPI 2
|
|
#define SPI_FLASH_CS_PIN PB12 // SPI2_NSS / Flash chip-select
|
|
#define SPI_FLASH_MOSI_PIN PB15
|
|
#define SPI_FLASH_MISO_PIN PB14
|
|
#define SPI_FLASH_SCK_PIN PB13
|
|
#define SPI_FLASH_SIZE 0x1000000 // 16MB
|
|
#endif
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
//#define SERVO0_PIN PA8 // use IO0 to enable BLTOUCH support/remove Mks_Wifi
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN PA15 // -X
|
|
#define Y_STOP_PIN PA12 // -Y
|
|
#define Z_MIN_PIN PA11 // -Z
|
|
#define Z_MAX_PIN PC4 // +Z
|
|
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN MT_DET_1_PIN
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_ENABLE_PIN PE4 // X_EN
|
|
#define X_STEP_PIN PE3 // X_STEP
|
|
#define X_DIR_PIN PE2 // X_DIR
|
|
|
|
#define Y_ENABLE_PIN PE1 // Y_EN
|
|
#define Y_STEP_PIN PE0 // Y_STEP
|
|
#define Y_DIR_PIN PB9 // Y_DIR
|
|
|
|
#define Z_ENABLE_PIN PB8 // Z_EN
|
|
#define Z_STEP_PIN PB5 // Z_STEP
|
|
#define Z_DIR_PIN PB4 // Z_DIR
|
|
|
|
#define E0_ENABLE_PIN PB3 // E0_EN
|
|
#define E0_STEP_PIN PD6 // E0_STEP
|
|
#define E0_DIR_PIN PD3 // E0_DIR
|
|
|
|
/**
|
|
* FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
|
|
* Several wiring options are provided below, defaulting to
|
|
* to the most compatible.
|
|
*/
|
|
#if HAS_TMC_UART
|
|
// SoftwareSerial with one pin per driver
|
|
// Compatible with TMC2208 and TMC2209 drivers
|
|
#define X_SERIAL_TX_PIN PA10 // RXD1
|
|
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
|
|
#define Y_SERIAL_TX_PIN PA9 // TXD1
|
|
#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
|
|
#define Z_SERIAL_TX_PIN PC7 // IO1
|
|
#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
|
|
#define TMC_BAUD_RATE 19200
|
|
#else
|
|
// Motor current PWM pins
|
|
#define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
|
|
#define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z
|
|
#define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
|
|
#ifndef DEFAULT_PWM_MOTOR_CURRENT
|
|
#define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
|
|
#endif
|
|
|
|
/**
|
|
* MKS Robin_Wifi or another ESP8266 module
|
|
*
|
|
* __ESP(M1)__ -J1-
|
|
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
|
|
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
|
|
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
|
|
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
|
|
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
|
|
* | nc | | nc | (01) WIFI_CTRL (PA5)
|
|
* RX| 21 | | nc |
|
|
* TX| 22 | | 01 |RST
|
|
* ￣￣ AE￣￣
|
|
*/
|
|
// Module ESP-WIFI
|
|
#define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
|
|
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
|
|
#define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST
|
|
#define ESP_WIFI_MODULE_ENABLE_PIN -1
|
|
#define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN
|
|
#define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN
|
|
#endif
|
|
|
|
//
|
|
// EXTRUDER
|
|
//
|
|
#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
|
|
#define E0_SERIAL_TX_PIN PA8 // IO0
|
|
#define E0_SERIAL_RX_PIN PA8 // IO0
|
|
#define TMC_BAUD_RATE 19200
|
|
#else
|
|
// Motor current PWM pins
|
|
#define MOTOR_CURRENT_PWM_E_PIN PB0 // VREF1 CONTROL E
|
|
#define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
|
|
#ifndef DEFAULT_PWM_MOTOR_CURRENT
|
|
#define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
|
|
#endif
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors (THM)
|
|
//
|
|
#define TEMP_0_PIN PC1 // TEMP_E0
|
|
#define TEMP_BED_PIN PC0 // TEMP_BED
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PC3 // HEATER_E0
|
|
#define HEATER_BED_PIN PA0 // HEATER_BED-WKUP
|
|
|
|
#define FAN_PIN PB1 // E_FAN
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#if ENABLED(BACKUP_POWER_SUPPLY)
|
|
#define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC
|
|
#else
|
|
//#define POWER_LOSS_PIN PA1 // PW_SO
|
|
#endif
|
|
|
|
/**
|
|
* Connector J2
|
|
* -------
|
|
* DIO O|1 2|O 3v3
|
|
* CSK O|3 5|O GND
|
|
* RST O|5 6|O GND
|
|
* -------
|
|
*/
|
|
//#define SW_DIO PA13
|
|
//#define SW_CLK PA14
|
|
//#define SW_RST NRST // (14)
|
|
|
|
//
|
|
// Power Supply Control
|
|
//
|
|
#if ENABLED(PSU_CONTROL)
|
|
#define KILL_PIN PA2 // PW_DET
|
|
#define KILL_PIN_STATE HIGH
|
|
//#define PS_ON_PIN PA3 // PW_CN /PW_OFF
|
|
#endif
|
|
|
|
#if HAS_TFT_LVGL_UI
|
|
#define MT_DET_1_PIN PA4 // MT_DET
|
|
#define MT_DET_2_PIN PE6
|
|
#define MT_DET_PIN_STATE LOW
|
|
#endif
|
|
|
|
//
|
|
// LED / NEOPixel
|
|
//
|
|
//#define LED_PIN PB2 // BOOT1
|
|
|
|
#if ENABLED(NEOPIXEL_LED)
|
|
#define LED_PWM PC7 // IO1
|
|
#ifndef NEOPIXEL_PIN
|
|
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN
|
|
#endif
|
|
#endif
|
|
|
|
//
|
|
// SD Card
|
|
//
|
|
#ifndef SDCARD_CONNECTION
|
|
#define SDCARD_CONNECTION ONBOARD
|
|
#endif
|
|
|
|
// Use the on-board card socket labeled SD_Extender
|
|
#if SD_CONNECTION_IS(CUSTOM_CABLE)
|
|
#define SD_SCK_PIN PC12
|
|
#define SD_MISO_PIN PC8
|
|
#define SD_MOSI_PIN PD2
|
|
#define SD_SS_PIN -1
|
|
#define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection)
|
|
#else
|
|
#define SDIO_SUPPORT
|
|
#define SDIO_CLOCK 4500000 // 4.5 MHz
|
|
#define SDIO_READ_RETRIES 16
|
|
#define ONBOARD_SPI_DEVICE 1 // SPI1
|
|
#define ONBOARD_SD_CS_PIN PC11
|
|
#define SD_DETECT_PIN -1 // SD_CD (-1 active refresh)
|
|
#endif
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#ifndef BEEPER_PIN
|
|
#define BEEPER_PIN PC5
|
|
#endif
|
|
|
|
#if ENABLED(SPEAKER) && BEEPER_PIN == PC5
|
|
#error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER."
|
|
#endif
|
|
|
|
//
|
|
// TFT with FSMC interface
|
|
//
|
|
#if HAS_FSMC_TFT
|
|
/**
|
|
* Note: MKS Robin TFT screens use various TFT controllers
|
|
* Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
|
|
* ILI9488 is not supported
|
|
* Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp
|
|
*
|
|
* If the screen stays white, disable 'LCD_RESET_PIN'
|
|
* to let the bootloader init the screen.
|
|
*
|
|
* Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu
|
|
* because Marlin uses the reset as a failsafe to revive a glitchy LCD.
|
|
*/
|
|
//#define TFT_RESET_PIN PC6 // FSMC_RST
|
|
#define TFT_BACKLIGHT_PIN PD13
|
|
|
|
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
|
|
#define FSMC_DMA_DEV DMA2
|
|
#define FSMC_DMA_CHANNEL DMA_CH5
|
|
|
|
#define FSMC_CS_PIN PD7 // NE4
|
|
#define FSMC_RS_PIN PD11 // A0
|
|
|
|
#define TFT_CS_PIN FSMC_CS_PIN
|
|
#define TFT_RS_PIN FSMC_RS_PIN
|
|
|
|
#ifdef TFT_CLASSIC_UI
|
|
#define TFT_MARLINBG_COLOR 0x3186 // Grey
|
|
#define TFT_MARLINUI_COLOR 0xC7B6 // Green
|
|
#define TFT_BTARROWS_COLOR 0xDEE6 // Yellow
|
|
#define TFT_BTOKMENU_COLOR 0x145F // Cyan
|
|
#endif
|
|
#define TFT_BUFFER_SIZE 14400
|
|
|
|
#elif HAS_GRAPHICAL_TFT
|
|
|
|
#define TFT_RESET_PIN PC6
|
|
#define TFT_BACKLIGHT_PIN PD13
|
|
#define TFT_CS_PIN PD7 // NE4
|
|
#define TFT_RS_PIN PD11 // A0
|
|
|
|
#endif
|
|
|
|
#if NEED_TOUCH_PINS
|
|
#define TOUCH_CS_PIN PC2 // SPI2_NSS
|
|
#define TOUCH_SCK_PIN PB13 // SPI2_SCK
|
|
#define TOUCH_MISO_PIN PB14 // SPI2_MISO
|
|
#define TOUCH_MOSI_PIN PB15 // SPI2_MOSI
|
|
#define TOUCH_INT_PIN -1
|
|
#endif
|
|
|