Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

216 lines
8.0 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
/**
* servo.cpp - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2
* Copyright (c) 2009 Michael Margolis. All right reserved.
*/
/**
* A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method.
* The servos are pulsed in the background using the value most recently written using the write() method
*
* Note that analogWrite of PWM on pins associated with the timer are disabled when the first servo is attached.
* Timers are seized as needed in groups of 12 servos - 24 servos use two timers, 48 servos will use four.
*
* The methods are:
*
* Servo - Class for manipulating servo motors connected to Arduino pins.
*
* attach(pin) - Attach a servo motor to an i/o pin.
* attach(pin, min, max) - Attach to a pin, setting min and max values in microseconds
* Default min is 544, max is 2400
*
* write() - Set the servo angle in degrees. (Invalid angles —over MIN_PULSE_WIDTH— are treated as µs.)
* writeMicroseconds() - Set the servo pulse width in microseconds.
* move(pin, angle) - Sequence of attach(pin), write(angle), safe_delay(servo_delay[servoIndex]).
* With DEACTIVATE_SERVOS_AFTER_MOVE it detaches after servo_delay[servoIndex].
* read() - Get the last-written servo pulse width as an angle between 0 and 180.
* readMicroseconds() - Get the last-written servo pulse width in microseconds.
* attached() - Return true if a servo is attached.
* detach() - Stop an attached servo from pulsing its i/o pin.
*/
#ifdef __AVR__
#include "../../inc/MarlinConfig.h"
#if HAS_SERVOS
#include <avr/interrupt.h>
#include "../shared/servo.h"
#include "../shared/servo_private.h"
static volatile int8_t Channel[_Nbr_16timers]; // counter for the servo being pulsed for each timer (or -1 if refresh interval)
/************ static functions common to all instances ***********************/
static inline void handle_interrupts(timer16_Sequence_t timer, volatile uint16_t* TCNTn, volatile uint16_t* OCRnA) {
if (Channel[timer] < 0)
*TCNTn = 0; // channel set to -1 indicated that refresh interval completed so reset the timer
else {
if (SERVO_INDEX(timer, Channel[timer]) < ServoCount && SERVO(timer, Channel[timer]).Pin.isActive)
extDigitalWrite(SERVO(timer, Channel[timer]).Pin.nbr, LOW); // pulse this channel low if activated
}
Channel[timer]++; // increment to the next channel
if (SERVO_INDEX(timer, Channel[timer]) < ServoCount && Channel[timer] < SERVOS_PER_TIMER) {
*OCRnA = *TCNTn + SERVO(timer, Channel[timer]).ticks;
if (SERVO(timer, Channel[timer]).Pin.isActive) // check if activated
extDigitalWrite(SERVO(timer, Channel[timer]).Pin.nbr, HIGH); // it's an active channel so pulse it high
}
else {
// finished all channels so wait for the refresh period to expire before starting over
if (((unsigned)*TCNTn) + 4 < usToTicks(REFRESH_INTERVAL)) // allow a few ticks to ensure the next OCR1A not missed
*OCRnA = (unsigned int)usToTicks(REFRESH_INTERVAL);
else
*OCRnA = *TCNTn + 4; // at least REFRESH_INTERVAL has elapsed
Channel[timer] = -1; // this will get incremented at the end of the refresh period to start again at the first channel
}
}
#ifndef WIRING // Wiring pre-defines signal handlers so don't define any if compiling for the Wiring platform
// Interrupt handlers for Arduino
#ifdef _useTimer1
SIGNAL(TIMER1_COMPA_vect) { handle_interrupts(_timer1, &TCNT1, &OCR1A); }
#endif
#ifdef _useTimer3
SIGNAL(TIMER3_COMPA_vect) { handle_interrupts(_timer3, &TCNT3, &OCR3A); }
#endif
#ifdef _useTimer4
SIGNAL(TIMER4_COMPA_vect) { handle_interrupts(_timer4, &TCNT4, &OCR4A); }
#endif
#ifdef _useTimer5
SIGNAL(TIMER5_COMPA_vect) { handle_interrupts(_timer5, &TCNT5, &OCR5A); }
#endif
#else // WIRING
// Interrupt handlers for Wiring
#ifdef _useTimer1
void Timer1Service() { handle_interrupts(_timer1, &TCNT1, &OCR1A); }
#endif
#ifdef _useTimer3
void Timer3Service() { handle_interrupts(_timer3, &TCNT3, &OCR3A); }
#endif
#endif // WIRING
/****************** end of static functions ******************************/
void initISR(timer16_Sequence_t timer) {
#ifdef _useTimer1
if (timer == _timer1) {
TCCR1A = 0; // normal counting mode
TCCR1B = _BV(CS11); // set prescaler of 8
TCNT1 = 0; // clear the timer count
#if defined(__AVR_ATmega8__) || defined(__AVR_ATmega128__)
SBI(TIFR, OCF1A); // clear any pending interrupts;
SBI(TIMSK, OCIE1A); // enable the output compare interrupt
#else
// here if not ATmega8 or ATmega128
SBI(TIFR1, OCF1A); // clear any pending interrupts;
SBI(TIMSK1, OCIE1A); // enable the output compare interrupt
#endif
#ifdef WIRING
timerAttach(TIMER1OUTCOMPAREA_INT, Timer1Service);
#endif
}
#endif
#ifdef _useTimer3
if (timer == _timer3) {
TCCR3A = 0; // normal counting mode
TCCR3B = _BV(CS31); // set prescaler of 8
TCNT3 = 0; // clear the timer count
#ifdef __AVR_ATmega128__
SBI(TIFR, OCF3A); // clear any pending interrupts;
SBI(ETIMSK, OCIE3A); // enable the output compare interrupt
#else
SBI(TIFR3, OCF3A); // clear any pending interrupts;
SBI(TIMSK3, OCIE3A); // enable the output compare interrupt
#endif
#ifdef WIRING
timerAttach(TIMER3OUTCOMPAREA_INT, Timer3Service); // for Wiring platform only
#endif
}
#endif
#ifdef _useTimer4
if (timer == _timer4) {
TCCR4A = 0; // normal counting mode
TCCR4B = _BV(CS41); // set prescaler of 8
TCNT4 = 0; // clear the timer count
TIFR4 = _BV(OCF4A); // clear any pending interrupts;
TIMSK4 = _BV(OCIE4A); // enable the output compare interrupt
}
#endif
#ifdef _useTimer5
if (timer == _timer5) {
TCCR5A = 0; // normal counting mode
TCCR5B = _BV(CS51); // set prescaler of 8
TCNT5 = 0; // clear the timer count
TIFR5 = _BV(OCF5A); // clear any pending interrupts;
TIMSK5 = _BV(OCIE5A); // enable the output compare interrupt
}
#endif
}
void finISR(timer16_Sequence_t timer) {
// Disable use of the given timer
#ifdef WIRING
if (timer == _timer1) {
CBI(
#if defined(__AVR_ATmega1281__) || defined(__AVR_ATmega2561__)
TIMSK1
#else
TIMSK
#endif
, OCIE1A); // disable timer 1 output compare interrupt
timerDetach(TIMER1OUTCOMPAREA_INT);
}
else if (timer == _timer3) {
CBI(
#if defined(__AVR_ATmega1281__) || defined(__AVR_ATmega2561__)
TIMSK3
#else
ETIMSK
#endif
, OCIE3A); // disable the timer3 output compare A interrupt
timerDetach(TIMER3OUTCOMPAREA_INT);
}
#else // !WIRING
// For arduino - in future: call here to a currently undefined function to reset the timer
UNUSED(timer);
#endif
}
#endif // HAS_SERVOS
#endif // __AVR__