You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
113 lines
4.0 KiB
113 lines
4.0 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* Leapfrog Xeed Driver board pin assignments
|
|
*
|
|
* This board is used by other Leapfrog printers in addition to the Xeed,
|
|
* such as the Creatr HS and Bolt. The pin assignments vary wildly between
|
|
* printer models. As such this file is currently specific to the Xeed.
|
|
*/
|
|
|
|
#include "env_validate.h"
|
|
|
|
#define BOARD_INFO_NAME "Leapfrog Xeed 2015"
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN 47 // 'X Min'
|
|
#define Y_STOP_PIN 48 // 'Y Min'
|
|
#define Z_STOP_PIN 49 // 'Z Min'
|
|
|
|
//
|
|
// Steppers
|
|
// The Xeed utilizes three Z-axis motors, which use the X, Y, and Z stepper connectors
|
|
// on the board. The X and Y steppers use external drivers, attached to signal-level
|
|
// Y-axis and X-axis connectors on the board, which map to distinct CPU pins from
|
|
// the on-board X/Y stepper drivers.
|
|
//
|
|
|
|
// X-axis signal-level connector
|
|
#define X_STEP_PIN 65
|
|
#define X_DIR_PIN 64
|
|
#define X_ENABLE_PIN 66 // Not actually used on Xeed, could be repurposed
|
|
|
|
// Y-axis signal-level connector
|
|
#define Y_STEP_PIN 23
|
|
#define Y_DIR_PIN 22
|
|
#define Y_ENABLE_PIN 24 // Not actually used on Xeed, could be repurposed
|
|
|
|
// ZMOT connector (Front Right Z Motor)
|
|
#define Z_STEP_PIN 31
|
|
#define Z_DIR_PIN 32
|
|
#define Z_ENABLE_PIN 30
|
|
|
|
// XMOT connector (Rear Z Motor)
|
|
#define Z2_STEP_PIN 28
|
|
#define Z2_DIR_PIN 63
|
|
#define Z2_ENABLE_PIN 29
|
|
|
|
// YMOT connector (Front Left Z Motor)
|
|
#define Z3_STEP_PIN 14
|
|
#define Z3_DIR_PIN 15
|
|
#define Z3_ENABLE_PIN 39
|
|
|
|
// EMOT2 connector
|
|
#define E0_STEP_PIN 37
|
|
#define E0_DIR_PIN 40
|
|
#define E0_ENABLE_PIN 36
|
|
|
|
// EMOT connector
|
|
#define E1_STEP_PIN 34
|
|
#define E1_DIR_PIN 35
|
|
#define E1_ENABLE_PIN 33
|
|
|
|
//
|
|
// Filament runout
|
|
//
|
|
#define FIL_RUNOUT_PIN 42 // ROT2 Connector
|
|
#define FIL_RUNOUT2_PIN 44 // ROT1 Connector
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 15 // T3 Connector
|
|
#define TEMP_1_PIN 13 // T1 Connector
|
|
#define TEMP_BED_PIN 14 // BED Connector (Between T1 and T3)
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 8 // Misc Connector, pins 3 and 4 (Out2)
|
|
#define HEATER_1_PIN 9 // Misc Connector, pins 5 and 6 (Out3)
|
|
#define HEATER_BED_PIN 6 // Misc Connector, pins 9(-) and 10(+) (OutA)
|
|
|
|
#define FAN_PIN 10 // Misc Connector, pins 7(-) and 8 (+) (Out4)
|
|
|
|
#define LED_PIN 13
|
|
|
|
#define SOL1_PIN 7 // Misc Connector, pins 1(-) and 2(+) (Out1)
|
|
|
|
// Door Closed Sensor
|
|
//#define DOOR_PIN 45 // HM1 Connector
|
|
|