You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
265 lines
8.3 KiB
265 lines
8.3 KiB
/**
|
|
* SanityCheck.h
|
|
*
|
|
* Test configuration values for errors at compile-time.
|
|
*/
|
|
#ifndef SANITYCHECK_H
|
|
#define SANITYCHECK_H
|
|
|
|
/**
|
|
* Dual Stepper Drivers
|
|
*/
|
|
#if defined(Z_DUAL_STEPPER_DRIVERS) && defined(Y_DUAL_STEPPER_DRIVERS)
|
|
#error You cannot have dual stepper drivers for both Y and Z.
|
|
#endif
|
|
|
|
/**
|
|
* Progress Bar
|
|
*/
|
|
#ifdef LCD_PROGRESS_BAR
|
|
#ifdef DOGLCD
|
|
#warning LCD_PROGRESS_BAR does not apply to graphical displays.
|
|
#endif
|
|
#ifdef FILAMENT_LCD_DISPLAY
|
|
#error LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both.
|
|
#endif
|
|
#endif
|
|
|
|
/**
|
|
* Babystepping
|
|
*/
|
|
#ifdef BABYSTEPPING
|
|
#ifdef COREXY
|
|
#error BABYSTEPPING not implemented for COREXY yet.
|
|
#endif
|
|
#ifdef SCARA
|
|
#error BABYSTEPPING is not implemented for SCARA yet.
|
|
#endif
|
|
#if defined(DELTA) && defined(BABYSTEP_XY)
|
|
#error BABYSTEPPING only implemented for Z axis on deltabots.
|
|
#endif
|
|
#endif
|
|
|
|
/**
|
|
* Filament Change with Extruder Runout Prevention
|
|
*/
|
|
#if defined(FILAMENTCHANGEENABLE) && defined(EXTRUDER_RUNOUT_PREVENT)
|
|
#error EXTRUDER_RUNOUT_PREVENT currently incompatible with FILAMENTCHANGE.
|
|
#endif
|
|
|
|
/**
|
|
* Options only for EXTRUDERS == 1
|
|
*/
|
|
#if EXTRUDERS > 1
|
|
|
|
#if EXTRUDERS > 4
|
|
#error The maximum number of EXTRUDERS is 4.
|
|
#endif
|
|
|
|
#ifdef TEMP_SENSOR_1_AS_REDUNDANT
|
|
#error EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT.
|
|
#endif
|
|
|
|
#ifdef HEATERS_PARALLEL
|
|
#error EXTRUDERS must be 1 with HEATERS_PARALLEL.
|
|
#endif
|
|
|
|
#ifdef Y_DUAL_STEPPER_DRIVERS
|
|
#error EXTRUDERS must be 1 with Y_DUAL_STEPPER_DRIVERS.
|
|
#endif
|
|
|
|
#ifdef Z_DUAL_STEPPER_DRIVERS
|
|
#error EXTRUDERS must be 1 with Z_DUAL_STEPPER_DRIVERS.
|
|
#endif
|
|
|
|
#endif // EXTRUDERS > 1
|
|
|
|
/**
|
|
* Required LCD language
|
|
*/
|
|
#if !defined(DOGLCD) && defined(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780_JAPAN) && !defined(DISPLAY_CHARSET_HD44780_WESTERN)
|
|
#error You must enable either DISPLAY_CHARSET_HD44780_JAPAN or DISPLAY_CHARSET_HD44780_WESTERN for your LCD controller.
|
|
#endif
|
|
|
|
/**
|
|
* Auto Bed Leveling
|
|
*/
|
|
#ifdef ENABLE_AUTO_BED_LEVELING
|
|
|
|
/**
|
|
* Require a Z Min pin
|
|
*/
|
|
#if Z_MIN_PIN == -1
|
|
#if Z_PROBE_PIN == -1
|
|
#ifdef Z_PROBE_REPEATABILITY_TEST
|
|
#error You must have a Z_MIN or Z_PROBE endstop to enable Z_PROBE_REPEATABILITY_TEST.
|
|
#else
|
|
#error ENABLE_AUTO_BED_LEVELING requires a Z_MIN or Z_PROBE endstop. Z_MIN_PIN or Z_PROBE_PIN must point to a valid hardware pin.
|
|
#endif
|
|
#endif
|
|
#endif
|
|
|
|
/**
|
|
* Require a Z Probe Pin if Z_PROBE_AND_ENDSTOP is enabled.
|
|
*/
|
|
#if defined(Z_PROBE_AND_ENDSTOP)
|
|
#if Z_PROBE_PIN == -1
|
|
#error You must have a Z_PROBE_PIN defined if you enable Z_PROBE_AND_ENDSTOP
|
|
#endif
|
|
#endif
|
|
|
|
/**
|
|
* Check if Probe_Offset * Grid Points is greater than Probing Range
|
|
*/
|
|
#ifdef AUTO_BED_LEVELING_GRID
|
|
|
|
// Make sure probing points are reachable
|
|
#if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
|
|
#error "The given LEFT_PROBE_BED_POSITION can't be reached by the probe."
|
|
#elif RIGHT_PROBE_BED_POSITION > MAX_PROBE_X
|
|
#error "The given RIGHT_PROBE_BED_POSITION can't be reached by the probe."
|
|
#elif FRONT_PROBE_BED_POSITION < MIN_PROBE_Y
|
|
#error "The given FRONT_PROBE_BED_POSITION can't be reached by the probe."
|
|
#elif BACK_PROBE_BED_POSITION > MAX_PROBE_Y
|
|
#error "The given BACK_PROBE_BED_POSITION can't be reached by the probe."
|
|
#endif
|
|
|
|
#define PROBE_SIZE_X (X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1))
|
|
#define PROBE_SIZE_Y (Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1))
|
|
#define PROBE_AREA_WIDTH (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION)
|
|
#define PROBE_AREA_DEPTH (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION)
|
|
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
|
|
#if PROBE_SIZE_X <= -PROBE_AREA_WIDTH
|
|
#define X_PROBE_ERROR
|
|
#endif
|
|
#elif PROBE_SIZE_X >= PROBE_AREA_WIDTH
|
|
#define X_PROBE_ERROR
|
|
#endif
|
|
#ifdef X_PROBE_ERROR
|
|
#error The X axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS
|
|
#endif
|
|
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
|
|
#if PROBE_SIZE_Y <= -PROBE_AREA_DEPTH
|
|
#define Y_PROBE_ERROR
|
|
#endif
|
|
#elif PROBE_SIZE_Y >= PROBE_AREA_DEPTH
|
|
#define Y_PROBE_ERROR
|
|
#endif
|
|
#ifdef Y_PROBE_ERROR
|
|
#error The Y axis probing range is to small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS
|
|
#endif
|
|
|
|
#undef PROBE_SIZE_X
|
|
#undef PROBE_SIZE_Y
|
|
#undef PROBE_AREA_WIDTH
|
|
#undef PROBE_AREA_DEPTH
|
|
|
|
#else // !AUTO_BED_LEVELING_GRID
|
|
|
|
// Check the triangulation points
|
|
#if ABL_PROBE_PT_1_X < MIN_PROBE_X || ABL_PROBE_PT_1_X > MAX_PROBE_X
|
|
#error "The given ABL_PROBE_PT_1_X can't be reached by the probe."
|
|
#elif ABL_PROBE_PT_2_X < MIN_PROBE_X || ABL_PROBE_PT_2_X > MAX_PROBE_X
|
|
#error "The given ABL_PROBE_PT_2_X can't be reached by the probe."
|
|
#elif ABL_PROBE_PT_3_X < MIN_PROBE_X || ABL_PROBE_PT_3_X > MAX_PROBE_X
|
|
#error "The given ABL_PROBE_PT_3_X can't be reached by the probe."
|
|
#elif ABL_PROBE_PT_1_Y < MIN_PROBE_Y || ABL_PROBE_PT_1_Y > MAX_PROBE_Y
|
|
#error "The given ABL_PROBE_PT_1_Y can't be reached by the probe."
|
|
#elif ABL_PROBE_PT_2_Y < MIN_PROBE_Y || ABL_PROBE_PT_2_Y > MAX_PROBE_Y
|
|
#error "The given ABL_PROBE_PT_2_Y can't be reached by the probe."
|
|
#elif ABL_PROBE_PT_3_Y < MIN_PROBE_Y || ABL_PROBE_PT_3_Y > MAX_PROBE_Y
|
|
#error "The given ABL_PROBE_PT_3_Y can't be reached by the probe."
|
|
#endif
|
|
|
|
#endif // !AUTO_BED_LEVELING_GRID
|
|
|
|
#endif // ENABLE_AUTO_BED_LEVELING
|
|
|
|
/**
|
|
* ULTIPANEL encoder
|
|
*/
|
|
#if defined(ULTIPANEL) && !defined(NEWPANEL) && !defined(SR_LCD_2W_NL) && !defined(SHIFT_CLK)
|
|
#error ULTIPANEL requires some kind of encoder.
|
|
#endif
|
|
|
|
/**
|
|
* Delta has limited bed leveling options
|
|
*/
|
|
#ifdef DELTA
|
|
|
|
#ifdef ENABLE_AUTO_BED_LEVELING
|
|
|
|
#ifndef AUTO_BED_LEVELING_GRID
|
|
#error Only AUTO_BED_LEVELING_GRID is supported with DELTA.
|
|
#endif
|
|
|
|
#ifdef Z_PROBE_SLED
|
|
#error You cannot use Z_PROBE_SLED with DELTA.
|
|
#endif
|
|
|
|
#ifdef Z_PROBE_REPEATABILITY_TEST
|
|
#error Z_PROBE_REPEATABILITY_TEST is not supported with DELTA yet.
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
/**
|
|
* Allen Key Z Probe requires Auto Bed Leveling grid and Delta
|
|
*/
|
|
#if defined(Z_PROBE_ALLEN_KEY) && !(defined(AUTO_BED_LEVELING_GRID) && defined(DELTA))
|
|
#error Invalid use of Z_PROBE_ALLEN_KEY.
|
|
#endif
|
|
|
|
/**
|
|
* Dual X Carriage requirements
|
|
*/
|
|
#ifdef DUAL_X_CARRIAGE
|
|
#if EXTRUDERS == 1 || defined(COREXY) \
|
|
|| !defined(X2_ENABLE_PIN) || !defined(X2_STEP_PIN) || !defined(X2_DIR_PIN) \
|
|
|| !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS) \
|
|
|| !defined(X_MAX_PIN) || X_MAX_PIN < 0
|
|
#error Missing or invalid definitions for DUAL_X_CARRIAGE mode.
|
|
#endif
|
|
#if X_HOME_DIR != -1 || X2_HOME_DIR != 1
|
|
#error Please use canonical x-carriage assignment.
|
|
#endif
|
|
#endif // DUAL_X_CARRIAGE
|
|
|
|
/**
|
|
* Make sure auto fan pins don't conflict with the fan pin
|
|
*/
|
|
#if HAS_AUTO_FAN && HAS_FAN
|
|
#if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN
|
|
#error You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN
|
|
#elif EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN
|
|
#error You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN
|
|
#elif EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN
|
|
#error You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN
|
|
#elif EXTRUDER_3_AUTO_FAN_PIN == FAN_PIN
|
|
#error You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN
|
|
#endif
|
|
#endif
|
|
|
|
/**
|
|
* Test required HEATER defines
|
|
*/
|
|
#if EXTRUDERS > 3
|
|
#if !HAS_HEATER_3
|
|
#error HEATER_3_PIN not defined for this board
|
|
#endif
|
|
#elif EXTRUDERS > 2
|
|
#if !HAS_HEATER_2
|
|
#error HEATER_2_PIN not defined for this board
|
|
#endif
|
|
#elif EXTRUDERS > 1 || defined(HEATERS_PARALLEL)
|
|
#if !HAS_HEATER_1
|
|
#error HEATER_1_PIN not defined for this board
|
|
#endif
|
|
#endif
|
|
#if !HAS_HEATER_0
|
|
#error HEATER_0_PIN not defined for this board
|
|
#endif
|
|
|
|
#endif //SANITYCHECK_H
|
|
|