Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

87 lines
2.6 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Arduino Mega with RAMPS v1.4Plus, also known as 3DYMY version, pin assignments
* The differences to the RAMPS v1.4 are:
* - Swap heater E0 with E1
* - Swap pins 8 and 10. Bed/Fan/Hotend as labeled on the board are on pins 8/9/10.
* - Change pins 16->42, 17->44 and 29->53 used for display.
*
* Applies to the following boards:
*
* RAMPS_PLUS_EFB (Extruder, Fan, Bed)
* RAMPS_PLUS_EEB (Extruder, Extruder, Bed)
* RAMPS_PLUS_EFF (Extruder, Fan, Fan)
* RAMPS_PLUS_EEF (Extruder, Extruder, Fan)
* RAMPS_PLUS_SF (Spindle, Controller Fan)
*
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "RAMPS 1.4 Plus"
#endif
#define RAMPS_D8_PIN 10
#define RAMPS_D10_PIN 8
#include "pins_RAMPS.h"
//
// Steppers - Swap E0 / E1 on 3DYMY
//
#undef E0_STEP_PIN
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#undef E1_STEP_PIN
#undef E1_DIR_PIN
#undef E1_ENABLE_PIN
#define E0_STEP_PIN 36
#define E0_DIR_PIN 34
#define E0_ENABLE_PIN 30
#define E1_STEP_PIN 26
#define E1_DIR_PIN 28
#define E1_ENABLE_PIN 24
#undef X_CS_PIN
#undef Y_CS_PIN
#undef Z_CS_PIN
#undef E0_CS_PIN
#undef E1_CS_PIN
#if ENABLED(ULTRA_LCD) && DISABLED(REPRAPWORLD_GRAPHICAL_LCD) && (DISABLED(NEWPANEL) || DISABLED(PANEL_ONE)) && DISABLED(CR10_STOCKDISPLAY)
#if DISABLED(MKS_12864OLED) || ENABLED(MKS_12864OLED_SSD1306)
#undef LCD_PINS_RS
#define LCD_PINS_RS 42 // 3DYMY boards pin 16 -> 42
#undef LCD_PINS_ENABLE
#define LCD_PINS_ENABLE 44 // 3DYMY boards pin 17 -> 44
#endif
#undef LCD_PINS_D7
#define LCD_PINS_D7 53 // 3DYMY boards pin 29 -> 53
#endif