Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

123 lines
3.7 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Brainwave 1.0 pin assignments (AT90USB646)
*
* Requires hardware bundle for Arduino:
* https://github.com/unrepentantgeek/brainwave-arduino
*/
/**
* Rev B 16 JAN 2017
*
* Added pointer to a currently available Arduino IDE extension that will
* allow this board to use the latest Marlin software
*/
/**
* Rev C 2 JUN 2017
*
* Converted to Arduino pin numbering
*/
/**
* Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB
* This is the only known IDE extension that is compatible with the pin definitions
* in this file, Adrduino 1.6.12 and the latest mainstream Marlin software.
*
* "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share
* the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such
* that PWM1A, PWM1B & PWM1C can't be used.
*
* Installation:
*
* 1. In the Arduino IDE, under Files -> Preferences paste the following URL
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
* 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB
* and then click on "Install"
* 3. Select "AT90USB646_TEENSYPP" from the 'Tools -> Boards' menu.
*/
/**
* To burn the bootloader that comes with Marlin_AT90USB:
*
* 1. Connect your programmer to the board.
* 2. In Arduino IDE select "AT90USB646_TEENSYPP" and then select the programmer.
* 3. In Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
#ifndef __AVR_AT90USB646__
#error "Oops! Make sure you have 'AT90USB646_TEENSYPP' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Brainwave"
//
// Limit Switches
//
#define X_STOP_PIN 35 // A7
#define Y_STOP_PIN 34 // A6
#define Z_STOP_PIN 33 // A5
//
// Steppers
//
#define X_STEP_PIN 3 // D3
#define X_DIR_PIN 5 // D5
#define X_ENABLE_PIN 4 // D4
#define X_ATT_PIN 2 // D2
#define Y_STEP_PIN 7 // D7
#define Y_DIR_PIN 9 // E1
#define Y_ENABLE_PIN 8 // E0
#define Y_ATT_PIN 6 // D6
#define Z_STEP_PIN 11 // C1
#define Z_DIR_PIN 13 // C3
#define Z_ENABLE_PIN 12 // C2
#define Z_ATT_PIN 10 // C0
#define E0_STEP_PIN 15 // C5
#define E0_DIR_PIN 17 // C7
#define E0_ENABLE_PIN 16 // C6
#define E0_ATT_PIN 14 // C4
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // F7 Analog Input
#define TEMP_BED_PIN 6 // F6 Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 32 // A4 Extruder
#define HEATER_BED_PIN 18 // E6 Bed
#define FAN_PIN 31 // A3 Fan
//
// Misc. Functions
//
#define LED_PIN 19 // E7