You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
898 lines
32 KiB
898 lines
32 KiB
/**
|
|
* TMC26XStepper.cpp - - TMC26X Stepper library for Wiring/Arduino
|
|
*
|
|
* based on the stepper library by Tom Igoe, et. al.
|
|
*
|
|
* Copyright (c) 2011, Interactive Matter, Marcus Nowotny
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
* furnished to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in
|
|
* all copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
* THE SOFTWARE.
|
|
*/
|
|
|
|
#if defined(STM32GENERIC) && defined(STM32F7)
|
|
|
|
#include "../../../inc/MarlinConfigPre.h"
|
|
|
|
#if HAS_DRIVER(TMC2660)
|
|
|
|
#include <stdbool.h>
|
|
#include <SPI.h>
|
|
#include "TMC2660.h"
|
|
|
|
#include "../../../inc/MarlinConfig.h"
|
|
#include "../../../MarlinCore.h"
|
|
#include "../../../module/stepper/indirection.h"
|
|
#include "../../../module/printcounter.h"
|
|
#include "../../../libs/duration_t.h"
|
|
#include "../../../libs/hex_print.h"
|
|
|
|
//some default values used in initialization
|
|
#define DEFAULT_MICROSTEPPING_VALUE 32
|
|
|
|
//TMC26X register definitions
|
|
#define DRIVER_CONTROL_REGISTER 0x0UL
|
|
#define CHOPPER_CONFIG_REGISTER 0x80000UL
|
|
#define COOL_STEP_REGISTER 0xA0000ul
|
|
#define STALL_GUARD2_LOAD_MEASURE_REGISTER 0xC0000ul
|
|
#define DRIVER_CONFIG_REGISTER 0xE0000ul
|
|
|
|
#define REGISTER_BIT_PATTERN 0xFFFFFul
|
|
|
|
//definitions for the driver control register
|
|
#define MICROSTEPPING_PATTERN 0xFul
|
|
#define STEP_INTERPOLATION 0x200UL
|
|
#define DOUBLE_EDGE_STEP 0x100UL
|
|
#define VSENSE 0x40UL
|
|
#define READ_MICROSTEP_POSTION 0x0UL
|
|
#define READ_STALL_GUARD_READING 0x10UL
|
|
#define READ_STALL_GUARD_AND_COOL_STEP 0x20UL
|
|
#define READ_SELECTION_PATTERN 0x30UL
|
|
|
|
//definitions for the chopper config register
|
|
#define CHOPPER_MODE_STANDARD 0x0UL
|
|
#define CHOPPER_MODE_T_OFF_FAST_DECAY 0x4000UL
|
|
#define T_OFF_PATTERN 0xFul
|
|
#define RANDOM_TOFF_TIME 0x2000UL
|
|
#define BLANK_TIMING_PATTERN 0x18000UL
|
|
#define BLANK_TIMING_SHIFT 15
|
|
#define HYSTERESIS_DECREMENT_PATTERN 0x1800UL
|
|
#define HYSTERESIS_DECREMENT_SHIFT 11
|
|
#define HYSTERESIS_LOW_VALUE_PATTERN 0x780UL
|
|
#define HYSTERESIS_LOW_SHIFT 7
|
|
#define HYSTERESIS_START_VALUE_PATTERN 0x78UL
|
|
#define HYSTERESIS_START_VALUE_SHIFT 4
|
|
#define T_OFF_TIMING_PATERN 0xFul
|
|
|
|
//definitions for cool step register
|
|
#define MINIMUM_CURRENT_FOURTH 0x8000UL
|
|
#define CURRENT_DOWN_STEP_SPEED_PATTERN 0x6000UL
|
|
#define SE_MAX_PATTERN 0xF00ul
|
|
#define SE_CURRENT_STEP_WIDTH_PATTERN 0x60UL
|
|
#define SE_MIN_PATTERN 0xFul
|
|
|
|
//definitions for StallGuard2 current register
|
|
#define STALL_GUARD_FILTER_ENABLED 0x10000UL
|
|
#define STALL_GUARD_TRESHHOLD_VALUE_PATTERN 0x17F00ul
|
|
#define CURRENT_SCALING_PATTERN 0x1Ful
|
|
#define STALL_GUARD_CONFIG_PATTERN 0x17F00ul
|
|
#define STALL_GUARD_VALUE_PATTERN 0x7F00ul
|
|
|
|
//definitions for the input from the TMC2660
|
|
#define STATUS_STALL_GUARD_STATUS 0x1UL
|
|
#define STATUS_OVER_TEMPERATURE_SHUTDOWN 0x2UL
|
|
#define STATUS_OVER_TEMPERATURE_WARNING 0x4UL
|
|
#define STATUS_SHORT_TO_GROUND_A 0x8UL
|
|
#define STATUS_SHORT_TO_GROUND_B 0x10UL
|
|
#define STATUS_OPEN_LOAD_A 0x20UL
|
|
#define STATUS_OPEN_LOAD_B 0x40UL
|
|
#define STATUS_STAND_STILL 0x80UL
|
|
#define READOUT_VALUE_PATTERN 0xFFC00ul
|
|
|
|
#define CPU_32_BIT
|
|
|
|
//default values
|
|
#define INITIAL_MICROSTEPPING 0x3UL //32th microstepping
|
|
|
|
SPIClass SPI_6(SPI6, SPI6_MOSI_PIN, SPI6_MISO_PIN, SPI6_SCK_PIN);
|
|
|
|
#define STEPPER_SPI SPI_6
|
|
|
|
//debuging output
|
|
|
|
//#define TMC_DEBUG1
|
|
|
|
uint8_t current_scaling = 0;
|
|
|
|
/**
|
|
* Constructor
|
|
* number_of_steps - the steps per rotation
|
|
* cs_pin - the SPI client select pin
|
|
* dir_pin - the pin where the direction pin is connected
|
|
* step_pin - the pin where the step pin is connected
|
|
*/
|
|
TMC26XStepper::TMC26XStepper(const int16_t in_steps, int16_t cs_pin, int16_t dir_pin, int16_t step_pin, uint16_t current, uint16_t resistor) {
|
|
// We are not started yet
|
|
started = false;
|
|
|
|
// By default cool step is not enabled
|
|
cool_step_enabled = false;
|
|
|
|
// Save the pins for later use
|
|
this->cs_pin = cs_pin;
|
|
this->dir_pin = dir_pin;
|
|
this->step_pin = step_pin;
|
|
|
|
// Store the current sense resistor value for later use
|
|
this->resistor = resistor;
|
|
|
|
// Initizalize our status values
|
|
this->steps_left = 0;
|
|
this->direction = 0;
|
|
|
|
// Initialize register values
|
|
driver_control_register_value = DRIVER_CONTROL_REGISTER | INITIAL_MICROSTEPPING;
|
|
chopper_config_register = CHOPPER_CONFIG_REGISTER;
|
|
|
|
// Setting the default register values
|
|
driver_control_register_value = DRIVER_CONTROL_REGISTER|INITIAL_MICROSTEPPING;
|
|
microsteps = _BV(INITIAL_MICROSTEPPING);
|
|
chopper_config_register = CHOPPER_CONFIG_REGISTER;
|
|
cool_step_register_value = COOL_STEP_REGISTER;
|
|
stallguard2_current_register_value = STALL_GUARD2_LOAD_MEASURE_REGISTER;
|
|
driver_configuration_register_value = DRIVER_CONFIG_REGISTER | READ_STALL_GUARD_READING;
|
|
|
|
// Set the current
|
|
setCurrent(current);
|
|
// Set to a conservative start value
|
|
setConstantOffTimeChopper(7, 54, 13,12,1);
|
|
// Set a nice microstepping value
|
|
setMicrosteps(DEFAULT_MICROSTEPPING_VALUE);
|
|
// Save the number of steps
|
|
number_of_steps = in_steps;
|
|
}
|
|
|
|
|
|
/**
|
|
* start & configure the stepper driver
|
|
* just must be called.
|
|
*/
|
|
void TMC26XStepper::start() {
|
|
|
|
#ifdef TMC_DEBUG1
|
|
SERIAL_ECHOLNPGM("\n TMC26X stepper library");
|
|
SERIAL_ECHOPAIR("\n CS pin: ", cs_pin);
|
|
SERIAL_ECHOPAIR("\n DIR pin: ", dir_pin);
|
|
SERIAL_ECHOPAIR("\n STEP pin: ", step_pin);
|
|
SERIAL_PRINTF("\n current scaling: %d", current_scaling);
|
|
SERIAL_PRINTF("\n Resistor: %d", resistor);
|
|
//SERIAL_PRINTF("\n current: %d", current);
|
|
SERIAL_ECHOPAIR("\n Microstepping: ", microsteps);
|
|
#endif
|
|
|
|
//set the pins as output & its initial value
|
|
pinMode(step_pin, OUTPUT);
|
|
pinMode(dir_pin, OUTPUT);
|
|
pinMode(cs_pin, OUTPUT);
|
|
extDigitalWrite(step_pin, LOW);
|
|
extDigitalWrite(dir_pin, LOW);
|
|
extDigitalWrite(cs_pin, HIGH);
|
|
|
|
STEPPER_SPI.begin();
|
|
STEPPER_SPI.beginTransaction(SPISettings(4000000, MSBFIRST, SPI_MODE3));
|
|
|
|
//set the initial values
|
|
send262(driver_control_register_value);
|
|
send262(chopper_config_register);
|
|
send262(cool_step_register_value);
|
|
send262(stallguard2_current_register_value);
|
|
send262(driver_configuration_register_value);
|
|
|
|
//save that we are in running mode
|
|
started = true;
|
|
}
|
|
|
|
/**
|
|
* Mark the driver as unstarted to be able to start it again
|
|
*/
|
|
void TMC26XStepper::un_start() { started = false; }
|
|
|
|
|
|
/**
|
|
* Sets the speed in revs per minute
|
|
*/
|
|
void TMC26XStepper::setSpeed(uint16_t whatSpeed) {
|
|
this->speed = whatSpeed;
|
|
this->step_delay = 60UL * sq(1000UL) / ((uint32_t)this->number_of_steps * (uint32_t)whatSpeed * (uint32_t)this->microsteps);
|
|
#ifdef TMC_DEBUG0 // crashes
|
|
SERIAL_ECHOPAIR("\nStep delay in micros: ", this->step_delay);
|
|
#endif
|
|
// Update the next step time
|
|
this->next_step_time = this->last_step_time + this->step_delay;
|
|
}
|
|
|
|
uint16_t TMC26XStepper::getSpeed() { return this->speed; }
|
|
|
|
/**
|
|
* Moves the motor steps_to_move steps.
|
|
* Negative indicates the reverse direction.
|
|
*/
|
|
char TMC26XStepper::step(int16_t steps_to_move) {
|
|
if (this->steps_left == 0) {
|
|
this->steps_left = ABS(steps_to_move); // how many steps to take
|
|
|
|
// determine direction based on whether steps_to_move is + or -:
|
|
if (steps_to_move > 0)
|
|
this->direction = 1;
|
|
else if (steps_to_move < 0)
|
|
this->direction = 0;
|
|
return 0;
|
|
}
|
|
return -1;
|
|
}
|
|
|
|
char TMC26XStepper::move() {
|
|
// decrement the number of steps, moving one step each time:
|
|
if (this->steps_left > 0) {
|
|
uint32_t time = micros();
|
|
// move only if the appropriate delay has passed:
|
|
|
|
// rem if (time >= this->next_step_time) {
|
|
|
|
if (ABS(time - this->last_step_time) > this->step_delay) {
|
|
// increment or decrement the step number,
|
|
// depending on direction:
|
|
if (this->direction == 1)
|
|
extDigitalWrite(step_pin, HIGH);
|
|
else {
|
|
extDigitalWrite(dir_pin, HIGH);
|
|
extDigitalWrite(step_pin, HIGH);
|
|
}
|
|
// get the timeStamp of when you stepped:
|
|
this->last_step_time = time;
|
|
this->next_step_time = time + this->step_delay;
|
|
// decrement the steps left:
|
|
steps_left--;
|
|
//disable the step & dir pins
|
|
extDigitalWrite(step_pin, LOW);
|
|
extDigitalWrite(dir_pin, LOW);
|
|
}
|
|
return -1;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
char TMC26XStepper::isMoving() { return this->steps_left > 0; }
|
|
|
|
uint16_t TMC26XStepper::getStepsLeft() { return this->steps_left; }
|
|
|
|
char TMC26XStepper::stop() {
|
|
//note to self if the motor is currently moving
|
|
char state = isMoving();
|
|
//stop the motor
|
|
this->steps_left = 0;
|
|
this->direction = 0;
|
|
//return if it was moving
|
|
return state;
|
|
}
|
|
|
|
void TMC26XStepper::setCurrent(uint16_t current) {
|
|
uint8_t current_scaling = 0;
|
|
//calculate the current scaling from the max current setting (in mA)
|
|
float mASetting = (float)current,
|
|
resistor_value = (float)this->resistor;
|
|
// remove vsense flag
|
|
this->driver_configuration_register_value &= ~(VSENSE);
|
|
// Derived from I = (cs + 1) / 32 * (Vsense / Rsense)
|
|
// leading to cs = 32 * R * I / V (with V = 0,31V oder 0,165V and I = 1000 * current)
|
|
// with Rsense = 0,15
|
|
// for vsense = 0,310V (VSENSE not set)
|
|
// or vsense = 0,165V (VSENSE set)
|
|
current_scaling = (byte)((resistor_value * mASetting * 32.0 / (0.31 * sq(1000.0))) - 0.5); //theoretically - 1.0 for better rounding it is 0.5
|
|
|
|
// Check if the current scalingis too low
|
|
if (current_scaling < 16) {
|
|
// Set the csense bit to get a use half the sense voltage (to support lower motor currents)
|
|
this->driver_configuration_register_value |= VSENSE;
|
|
// and recalculate the current setting
|
|
current_scaling = (byte)((resistor_value * mASetting * 32.0 / (0.165 * sq(1000.0))) - 0.5); //theoretically - 1.0 for better rounding it is 0.5
|
|
#ifdef TMC_DEBUG0 // crashes
|
|
SERIAL_ECHOPAIR("\nCS (Vsense=1): ",current_scaling);
|
|
#endif
|
|
}
|
|
#ifdef TMC_DEBUG0 // crashes
|
|
else
|
|
SERIAL_ECHOPAIR("\nCS: ", current_scaling);
|
|
#endif
|
|
|
|
// do some sanity checks
|
|
NOMORE(current_scaling, 31);
|
|
|
|
// delete the old value
|
|
stallguard2_current_register_value &= ~(CURRENT_SCALING_PATTERN);
|
|
// set the new current scaling
|
|
stallguard2_current_register_value |= current_scaling;
|
|
// if started we directly send it to the motor
|
|
if (started) {
|
|
send262(driver_configuration_register_value);
|
|
send262(stallguard2_current_register_value);
|
|
}
|
|
}
|
|
|
|
uint16_t TMC26XStepper::getCurrent() {
|
|
// Calculate the current according to the datasheet to be on the safe side.
|
|
// This is not the fastest but the most accurate and illustrative way.
|
|
float result = (float)(stallguard2_current_register_value & CURRENT_SCALING_PATTERN),
|
|
resistor_value = (float)this->resistor,
|
|
voltage = (driver_configuration_register_value & VSENSE) ? 0.165 : 0.31;
|
|
result = (result + 1.0) / 32.0 * voltage / resistor_value * sq(1000.0);
|
|
return (uint16_t)result;
|
|
}
|
|
|
|
void TMC26XStepper::setStallGuardThreshold(char stallguard_threshold, char stallguard_filter_enabled) {
|
|
// We just have 5 bits
|
|
LIMIT(stallguard_threshold, -64, 63);
|
|
|
|
// Add trim down to 7 bits
|
|
stallguard_threshold &= 0x7F;
|
|
// Delete old StallGuard settings
|
|
stallguard2_current_register_value &= ~(STALL_GUARD_CONFIG_PATTERN);
|
|
if (stallguard_filter_enabled)
|
|
stallguard2_current_register_value |= STALL_GUARD_FILTER_ENABLED;
|
|
|
|
// Set the new StallGuard threshold
|
|
stallguard2_current_register_value |= (((uint32_t)stallguard_threshold << 8) & STALL_GUARD_CONFIG_PATTERN);
|
|
// If started we directly send it to the motor
|
|
if (started) send262(stallguard2_current_register_value);
|
|
}
|
|
|
|
char TMC26XStepper::getStallGuardThreshold() {
|
|
uint32_t stallguard_threshold = stallguard2_current_register_value & STALL_GUARD_VALUE_PATTERN;
|
|
//shift it down to bit 0
|
|
stallguard_threshold >>= 8;
|
|
//convert the value to an int16_t to correctly handle the negative numbers
|
|
char result = stallguard_threshold;
|
|
//check if it is negative and fill it up with leading 1 for proper negative number representation
|
|
//rem if (result & _BV(6)) {
|
|
|
|
if (TEST(result, 6)) result |= 0xC0;
|
|
return result;
|
|
}
|
|
|
|
char TMC26XStepper::getStallGuardFilter() {
|
|
if (stallguard2_current_register_value & STALL_GUARD_FILTER_ENABLED)
|
|
return -1;
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* Set the number of microsteps per step.
|
|
* 0,2,4,8,16,32,64,128,256 is supported
|
|
* any value in between will be mapped to the next smaller value
|
|
* 0 and 1 set the motor in full step mode
|
|
*/
|
|
void TMC26XStepper::setMicrosteps(const int16_t in_steps) {
|
|
uint16_t setting_pattern;
|
|
|
|
if (in_steps >= 256) setting_pattern = 0;
|
|
else if (in_steps >= 128) setting_pattern = 1;
|
|
else if (in_steps >= 64) setting_pattern = 2;
|
|
else if (in_steps >= 32) setting_pattern = 3;
|
|
else if (in_steps >= 16) setting_pattern = 4;
|
|
else if (in_steps >= 8) setting_pattern = 5;
|
|
else if (in_steps >= 4) setting_pattern = 6;
|
|
else if (in_steps >= 2) setting_pattern = 7;
|
|
else if (in_steps <= 1) setting_pattern = 8; // 1 and 0 lead to full step
|
|
|
|
microsteps = _BV(8 - setting_pattern);
|
|
|
|
#ifdef TMC_DEBUG0 // crashes
|
|
SERIAL_ECHOPAIR("\n Microstepping: ", microsteps);
|
|
#endif
|
|
|
|
// Delete the old value
|
|
this->driver_control_register_value &= 0x000FFFF0UL;
|
|
|
|
// Set the new value
|
|
this->driver_control_register_value |= setting_pattern;
|
|
|
|
// If started we directly send it to the motor
|
|
if (started) send262(driver_control_register_value);
|
|
|
|
// Recalculate the stepping delay by simply setting the speed again
|
|
this->setSpeed(this->speed);
|
|
}
|
|
|
|
/**
|
|
* returns the effective number of microsteps at the moment
|
|
*/
|
|
int16_t TMC26XStepper::getMicrosteps() { return microsteps; }
|
|
|
|
/**
|
|
* constant_off_time: The off time setting controls the minimum chopper frequency.
|
|
* For most applications an off time within the range of 5μs to 20μs will fit.
|
|
* 2...15: off time setting
|
|
*
|
|
* blank_time: Selects the comparator blank time. This time needs to safely cover the switching event and the
|
|
* duration of the ringing on the sense resistor. For
|
|
* 0: min. setting 3: max. setting
|
|
*
|
|
* fast_decay_time_setting: Fast decay time setting. With CHM=1, these bits control the portion of fast decay for each chopper cycle.
|
|
* 0: slow decay only
|
|
* 1...15: duration of fast decay phase
|
|
*
|
|
* sine_wave_offset: Sine wave offset. With CHM=1, these bits control the sine wave offset.
|
|
* A positive offset corrects for zero crossing error.
|
|
* -3..-1: negative offset 0: no offset 1...12: positive offset
|
|
*
|
|
* use_current_comparator: Selects usage of the current comparator for termination of the fast decay cycle.
|
|
* If current comparator is enabled, it terminates the fast decay cycle in case the current
|
|
* reaches a higher negative value than the actual positive value.
|
|
* 1: enable comparator termination of fast decay cycle
|
|
* 0: end by time only
|
|
*/
|
|
void TMC26XStepper::setConstantOffTimeChopper(char constant_off_time, char blank_time, char fast_decay_time_setting, char sine_wave_offset, uint8_t use_current_comparator) {
|
|
// Perform some sanity checks
|
|
LIMIT(constant_off_time, 2, 15);
|
|
|
|
// Save the constant off time
|
|
this->constant_off_time = constant_off_time;
|
|
|
|
// Calculate the value acc to the clock cycles
|
|
const char blank_value = blank_time >= 54 ? 3 :
|
|
blank_time >= 36 ? 2 :
|
|
blank_time >= 24 ? 1 : 0;
|
|
|
|
LIMIT(fast_decay_time_setting, 0, 15);
|
|
LIMIT(sine_wave_offset, -3, 12);
|
|
|
|
// Shift the sine_wave_offset
|
|
sine_wave_offset += 3;
|
|
|
|
// Calculate the register setting
|
|
// First of all delete all the values for this
|
|
chopper_config_register &= ~(_BV(12) | BLANK_TIMING_PATTERN | HYSTERESIS_DECREMENT_PATTERN | HYSTERESIS_LOW_VALUE_PATTERN | HYSTERESIS_START_VALUE_PATTERN | T_OFF_TIMING_PATERN);
|
|
// Set the constant off pattern
|
|
chopper_config_register |= CHOPPER_MODE_T_OFF_FAST_DECAY;
|
|
// Set the blank timing value
|
|
chopper_config_register |= ((uint32_t)blank_value) << BLANK_TIMING_SHIFT;
|
|
// Setting the constant off time
|
|
chopper_config_register |= constant_off_time;
|
|
// Set the fast decay time
|
|
// Set msb
|
|
chopper_config_register |= (((uint32_t)(fast_decay_time_setting & 0x8)) << HYSTERESIS_DECREMENT_SHIFT);
|
|
// Other bits
|
|
chopper_config_register |= (((uint32_t)(fast_decay_time_setting & 0x7)) << HYSTERESIS_START_VALUE_SHIFT);
|
|
// Set the sine wave offset
|
|
chopper_config_register |= (uint32_t)sine_wave_offset << HYSTERESIS_LOW_SHIFT;
|
|
// Using the current comparator?
|
|
if (!use_current_comparator)
|
|
chopper_config_register |= _BV(12);
|
|
|
|
// If started we directly send it to the motor
|
|
if (started) {
|
|
// rem send262(driver_control_register_value);
|
|
send262(chopper_config_register);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* constant_off_time: The off time setting controls the minimum chopper frequency.
|
|
* For most applications an off time within the range of 5μs to 20μs will fit.
|
|
* 2...15: off time setting
|
|
*
|
|
* blank_time: Selects the comparator blank time. This time needs to safely cover the switching event and the
|
|
* duration of the ringing on the sense resistor. For
|
|
* 0: min. setting 3: max. setting
|
|
*
|
|
* hysteresis_start: Hysteresis start setting. Please remark, that this value is an offset to the hysteresis end value HEND.
|
|
* 1...8
|
|
*
|
|
* hysteresis_end: Hysteresis end setting. Sets the hysteresis end value after a number of decrements. Decrement interval time is controlled by HDEC.
|
|
* The sum HSTRT+HEND must be <16. At a current setting CS of max. 30 (amplitude reduced to 240), the sum is not limited.
|
|
* -3..-1: negative HEND 0: zero HEND 1...12: positive HEND
|
|
*
|
|
* hysteresis_decrement: Hysteresis decrement setting. This setting determines the slope of the hysteresis during on time and during fast decay time.
|
|
* 0: fast decrement 3: very slow decrement
|
|
*/
|
|
|
|
void TMC26XStepper::setSpreadCycleChopper(char constant_off_time, char blank_time, char hysteresis_start, char hysteresis_end, char hysteresis_decrement) {
|
|
// Perform some sanity checks
|
|
LIMIT(constant_off_time, 2, 15);
|
|
|
|
// Save the constant off time
|
|
this->constant_off_time = constant_off_time;
|
|
|
|
// Calculate the value acc to the clock cycles
|
|
const char blank_value = blank_time >= 54 ? 3 :
|
|
blank_time >= 36 ? 2 :
|
|
blank_time >= 24 ? 1 : 0;
|
|
|
|
LIMIT(hysteresis_start, 1, 8);
|
|
hysteresis_start--;
|
|
|
|
LIMIT(hysteresis_start, -3, 12);
|
|
|
|
// Shift the hysteresis_end
|
|
hysteresis_end += 3;
|
|
|
|
LIMIT(hysteresis_decrement, 0, 3);
|
|
|
|
//first of all delete all the values for this
|
|
chopper_config_register &= ~(CHOPPER_MODE_T_OFF_FAST_DECAY | BLANK_TIMING_PATTERN | HYSTERESIS_DECREMENT_PATTERN | HYSTERESIS_LOW_VALUE_PATTERN | HYSTERESIS_START_VALUE_PATTERN | T_OFF_TIMING_PATERN);
|
|
|
|
//set the blank timing value
|
|
chopper_config_register |= ((uint32_t)blank_value) << BLANK_TIMING_SHIFT;
|
|
//setting the constant off time
|
|
chopper_config_register |= constant_off_time;
|
|
//set the hysteresis_start
|
|
chopper_config_register |= ((uint32_t)hysteresis_start) << HYSTERESIS_START_VALUE_SHIFT;
|
|
//set the hysteresis end
|
|
chopper_config_register |= ((uint32_t)hysteresis_end) << HYSTERESIS_LOW_SHIFT;
|
|
//set the hystereis decrement
|
|
chopper_config_register |= ((uint32_t)blank_value) << BLANK_TIMING_SHIFT;
|
|
//if started we directly send it to the motor
|
|
if (started) {
|
|
//rem send262(driver_control_register_value);
|
|
send262(chopper_config_register);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* In a constant off time chopper scheme both coil choppers run freely, i.e. are not synchronized.
|
|
* The frequency of each chopper mainly depends on the coil current and the position dependant motor coil inductivity, thus it depends on the microstep position.
|
|
* With some motors a slightly audible beat can occur between the chopper frequencies, especially when they are near to each other. This typically occurs at a
|
|
* few microstep positions within each quarter wave. This effect normally is not audible when compared to mechanical noise generated by ball bearings, etc.
|
|
* Further factors which can cause a similar effect are a poor layout of sense resistor GND connection.
|
|
* Hint: A common factor, which can cause motor noise, is a bad PCB layout causing coupling of both sense resistor voltages
|
|
* (please refer to sense resistor layout hint in chapter 8.1).
|
|
* In order to minimize the effect of a beat between both chopper frequencies, an internal random generator is provided.
|
|
* It modulates the slow decay time setting when switched on by the RNDTF bit. The RNDTF feature further spreads the chopper spectrum,
|
|
* reducing electromagnetic emission on single frequencies.
|
|
*/
|
|
void TMC26XStepper::setRandomOffTime(char value) {
|
|
if (value)
|
|
chopper_config_register |= RANDOM_TOFF_TIME;
|
|
else
|
|
chopper_config_register &= ~(RANDOM_TOFF_TIME);
|
|
//if started we directly send it to the motor
|
|
if (started) {
|
|
//rem send262(driver_control_register_value);
|
|
send262(chopper_config_register);
|
|
}
|
|
}
|
|
|
|
void TMC26XStepper::setCoolStepConfiguration(
|
|
uint16_t lower_SG_threshold,
|
|
uint16_t SG_hysteresis,
|
|
uint8_t current_decrement_step_size,
|
|
uint8_t current_increment_step_size,
|
|
uint8_t lower_current_limit
|
|
) {
|
|
// Sanitize the input values
|
|
NOMORE(lower_SG_threshold, 480);
|
|
// Divide by 32
|
|
lower_SG_threshold >>= 5;
|
|
NOMORE(SG_hysteresis, 480);
|
|
// Divide by 32
|
|
SG_hysteresis >>= 5;
|
|
NOMORE(current_decrement_step_size, 3);
|
|
NOMORE(current_increment_step_size, 3);
|
|
NOMORE(lower_current_limit, 1);
|
|
|
|
// Store the lower level in order to enable/disable the cool step
|
|
this->cool_step_lower_threshold=lower_SG_threshold;
|
|
// If cool step is not enabled we delete the lower value to keep it disabled
|
|
if (!this->cool_step_enabled) lower_SG_threshold = 0;
|
|
// The good news is that we can start with a complete new cool step register value
|
|
// And simply set the values in the register
|
|
cool_step_register_value = ((uint32_t)lower_SG_threshold)
|
|
| (((uint32_t)SG_hysteresis) << 8)
|
|
| (((uint32_t)current_decrement_step_size) << 5)
|
|
| (((uint32_t)current_increment_step_size) << 13)
|
|
| (((uint32_t)lower_current_limit) << 15)
|
|
| COOL_STEP_REGISTER; // Register signature
|
|
|
|
if (started) send262(cool_step_register_value);
|
|
}
|
|
|
|
void TMC26XStepper::setCoolStepEnabled(boolean enabled) {
|
|
// Simply delete the lower limit to disable the cool step
|
|
cool_step_register_value &= ~SE_MIN_PATTERN;
|
|
// And set it to the proper value if cool step is to be enabled
|
|
if (enabled)
|
|
cool_step_register_value |= this->cool_step_lower_threshold;
|
|
// And save the enabled status
|
|
this->cool_step_enabled = enabled;
|
|
// Save the register value
|
|
if (started) send262(cool_step_register_value);
|
|
}
|
|
|
|
boolean TMC26XStepper::isCoolStepEnabled() { return this->cool_step_enabled; }
|
|
|
|
uint16_t TMC26XStepper::getCoolStepLowerSgThreshold() {
|
|
// We return our internally stored value - in order to provide the correct setting even if cool step is not enabled
|
|
return this->cool_step_lower_threshold<<5;
|
|
}
|
|
|
|
uint16_t TMC26XStepper::getCoolStepUpperSgThreshold() {
|
|
return uint8_t((cool_step_register_value & SE_MAX_PATTERN) >> 8) << 5;
|
|
}
|
|
|
|
uint8_t TMC26XStepper::getCoolStepCurrentIncrementSize() {
|
|
return uint8_t((cool_step_register_value & CURRENT_DOWN_STEP_SPEED_PATTERN) >> 13);
|
|
}
|
|
|
|
uint8_t TMC26XStepper::getCoolStepNumberOfSGReadings() {
|
|
return uint8_t((cool_step_register_value & SE_CURRENT_STEP_WIDTH_PATTERN) >> 5);
|
|
}
|
|
|
|
uint8_t TMC26XStepper::getCoolStepLowerCurrentLimit() {
|
|
return uint8_t((cool_step_register_value & MINIMUM_CURRENT_FOURTH) >> 15);
|
|
}
|
|
|
|
void TMC26XStepper::setEnabled(boolean enabled) {
|
|
//delete the t_off in the chopper config to get sure
|
|
chopper_config_register &= ~(T_OFF_PATTERN);
|
|
if (enabled) {
|
|
//and set the t_off time
|
|
chopper_config_register |= this->constant_off_time;
|
|
}
|
|
//if not enabled we don't have to do anything since we already delete t_off from the register
|
|
if (started) send262(chopper_config_register);
|
|
}
|
|
|
|
boolean TMC26XStepper::isEnabled() { return !!(chopper_config_register & T_OFF_PATTERN); }
|
|
|
|
/**
|
|
* reads a value from the TMC26X status register. The value is not obtained directly but can then
|
|
* be read by the various status routines.
|
|
*/
|
|
void TMC26XStepper::readStatus(char read_value) {
|
|
uint32_t old_driver_configuration_register_value = driver_configuration_register_value;
|
|
//reset the readout configuration
|
|
driver_configuration_register_value &= ~(READ_SELECTION_PATTERN);
|
|
//this now equals TMC26X_READOUT_POSITION - so we just have to check the other two options
|
|
if (read_value == TMC26X_READOUT_STALLGUARD)
|
|
driver_configuration_register_value |= READ_STALL_GUARD_READING;
|
|
else if (read_value == TMC26X_READOUT_CURRENT)
|
|
driver_configuration_register_value |= READ_STALL_GUARD_AND_COOL_STEP;
|
|
|
|
//all other cases are ignored to prevent funny values
|
|
//check if the readout is configured for the value we are interested in
|
|
if (driver_configuration_register_value != old_driver_configuration_register_value) {
|
|
//because then we need to write the value twice - one time for configuring, second time to get the value, see below
|
|
send262(driver_configuration_register_value);
|
|
}
|
|
//write the configuration to get the last status
|
|
send262(driver_configuration_register_value);
|
|
}
|
|
|
|
int16_t TMC26XStepper::getMotorPosition() {
|
|
//we read it out even if we are not started yet - perhaps it is useful information for somebody
|
|
readStatus(TMC26X_READOUT_POSITION);
|
|
return getReadoutValue();
|
|
}
|
|
|
|
//reads the StallGuard setting from last status
|
|
//returns -1 if StallGuard information is not present
|
|
int16_t TMC26XStepper::getCurrentStallGuardReading() {
|
|
//if we don't yet started there cannot be a StallGuard value
|
|
if (!started) return -1;
|
|
//not time optimal, but solution optiomal:
|
|
//first read out the StallGuard value
|
|
readStatus(TMC26X_READOUT_STALLGUARD);
|
|
return getReadoutValue();
|
|
}
|
|
|
|
uint8_t TMC26XStepper::getCurrentCSReading() {
|
|
//if we don't yet started there cannot be a StallGuard value
|
|
if (!started) return 0;
|
|
//not time optimal, but solution optiomal:
|
|
//first read out the StallGuard value
|
|
readStatus(TMC26X_READOUT_CURRENT);
|
|
return (getReadoutValue() & 0x1F);
|
|
}
|
|
|
|
uint16_t TMC26XStepper::getCurrentCurrent() {
|
|
float result = (float)getCurrentCSReading(),
|
|
resistor_value = (float)this->resistor,
|
|
voltage = (driver_configuration_register_value & VSENSE)? 0.165 : 0.31;
|
|
result = (result + 1.0) / 32.0 * voltage / resistor_value * sq(1000.0);
|
|
return (uint16_t)result;
|
|
}
|
|
|
|
/**
|
|
* Return true if the StallGuard threshold has been reached
|
|
*/
|
|
boolean TMC26XStepper::isStallGuardOverThreshold() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_STALL_GUARD_STATUS);
|
|
}
|
|
|
|
/**
|
|
* returns if there is any over temperature condition:
|
|
* OVER_TEMPERATURE_PREWARING if pre warning level has been reached
|
|
* OVER_TEMPERATURE_SHUTDOWN if the temperature is so hot that the driver is shut down
|
|
* Any of those levels are not too good.
|
|
*/
|
|
char TMC26XStepper::getOverTemperature() {
|
|
if (!this->started) return 0;
|
|
|
|
if (driver_status_result & STATUS_OVER_TEMPERATURE_SHUTDOWN)
|
|
return TMC26X_OVERTEMPERATURE_SHUTDOWN;
|
|
|
|
if (driver_status_result & STATUS_OVER_TEMPERATURE_WARNING)
|
|
return TMC26X_OVERTEMPERATURE_PREWARING;
|
|
|
|
return 0;
|
|
}
|
|
|
|
// Is motor channel A shorted to ground
|
|
boolean TMC26XStepper::isShortToGroundA() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_SHORT_TO_GROUND_A);
|
|
}
|
|
|
|
// Is motor channel B shorted to ground
|
|
boolean TMC26XStepper::isShortToGroundB() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_SHORT_TO_GROUND_B);
|
|
}
|
|
|
|
// Is motor channel A connected
|
|
boolean TMC26XStepper::isOpenLoadA() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_OPEN_LOAD_A);
|
|
}
|
|
|
|
// Is motor channel B connected
|
|
boolean TMC26XStepper::isOpenLoadB() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_OPEN_LOAD_B);
|
|
}
|
|
|
|
// Is chopper inactive since 2^20 clock cycles - defaults to ~0,08s
|
|
boolean TMC26XStepper::isStandStill() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_STAND_STILL);
|
|
}
|
|
|
|
//is chopper inactive since 2^20 clock cycles - defaults to ~0,08s
|
|
boolean TMC26XStepper::isStallGuardReached() {
|
|
if (!this->started) return false;
|
|
return (driver_status_result & STATUS_STALL_GUARD_STATUS);
|
|
}
|
|
|
|
//reads the StallGuard setting from last status
|
|
//returns -1 if StallGuard information is not present
|
|
int16_t TMC26XStepper::getReadoutValue() {
|
|
return (int)(driver_status_result >> 10);
|
|
}
|
|
|
|
int16_t TMC26XStepper::getResistor() { return this->resistor; }
|
|
|
|
boolean TMC26XStepper::isCurrentScalingHalfed() {
|
|
return !!(this->driver_configuration_register_value & VSENSE);
|
|
}
|
|
/**
|
|
* version() returns the version of the library:
|
|
*/
|
|
int16_t TMC26XStepper::version() { return 1; }
|
|
|
|
void TMC26XStepper::debugLastStatus() {
|
|
#ifdef TMC_DEBUG1
|
|
if (this->started) {
|
|
if (this->getOverTemperature()&TMC26X_OVERTEMPERATURE_PREWARING)
|
|
SERIAL_ECHOLNPGM("\n WARNING: Overtemperature Prewarning!");
|
|
else if (this->getOverTemperature()&TMC26X_OVERTEMPERATURE_SHUTDOWN)
|
|
SERIAL_ECHOLNPGM("\n ERROR: Overtemperature Shutdown!");
|
|
|
|
if (this->isShortToGroundA())
|
|
SERIAL_ECHOLNPGM("\n ERROR: SHORT to ground on channel A!");
|
|
|
|
if (this->isShortToGroundB())
|
|
SERIAL_ECHOLNPGM("\n ERROR: SHORT to ground on channel B!");
|
|
|
|
if (this->isOpenLoadA())
|
|
SERIAL_ECHOLNPGM("\n ERROR: Channel A seems to be unconnected!");
|
|
|
|
if (this->isOpenLoadB())
|
|
SERIAL_ECHOLNPGM("\n ERROR: Channel B seems to be unconnected!");
|
|
|
|
if (this->isStallGuardReached())
|
|
SERIAL_ECHOLNPGM("\n INFO: Stall Guard level reached!");
|
|
|
|
if (this->isStandStill())
|
|
SERIAL_ECHOLNPGM("\n INFO: Motor is standing still.");
|
|
|
|
uint32_t readout_config = driver_configuration_register_value & READ_SELECTION_PATTERN;
|
|
const int16_t value = getReadoutValue();
|
|
if (readout_config == READ_MICROSTEP_POSTION) {
|
|
SERIAL_ECHOPAIR("\n Microstep position phase A: ", value);
|
|
}
|
|
else if (readout_config == READ_STALL_GUARD_READING) {
|
|
SERIAL_ECHOPAIR("\n Stall Guard value:", value);
|
|
}
|
|
else if (readout_config == READ_STALL_GUARD_AND_COOL_STEP) {
|
|
SERIAL_ECHOPAIR("\n Approx Stall Guard: ", value & 0xF);
|
|
SERIAL_ECHOPAIR("\n Current level", value & 0x1F0);
|
|
}
|
|
}
|
|
#endif
|
|
}
|
|
|
|
/**
|
|
* send register settings to the stepper driver via SPI
|
|
* returns the current status
|
|
*/
|
|
inline void TMC26XStepper::send262(uint32_t datagram) {
|
|
uint32_t i_datagram;
|
|
|
|
//preserver the previous spi mode
|
|
//uint8_t oldMode = SPCR & SPI_MODE_MASK;
|
|
|
|
//if the mode is not correct set it to mode 3
|
|
//if (oldMode != SPI_MODE3) {
|
|
// SPI.setDataMode(SPI_MODE3);
|
|
//}
|
|
|
|
//select the TMC driver
|
|
extDigitalWrite(cs_pin, LOW);
|
|
|
|
//ensure that only valid bist are set (0-19)
|
|
//datagram &=REGISTER_BIT_PATTERN;
|
|
|
|
#ifdef TMC_DEBUG1
|
|
//SERIAL_PRINTF("Sending ");
|
|
//SERIAL_PRINTF("Sending ", datagram,HEX);
|
|
//SERIAL_ECHOPAIR("\n\nSending \n", print_hex_long(datagram));
|
|
SERIAL_PRINTF("\n\nSending %x", datagram);
|
|
#endif
|
|
|
|
//write/read the values
|
|
i_datagram = STEPPER_SPI.transfer((datagram >> 16) & 0xFF);
|
|
i_datagram <<= 8;
|
|
i_datagram |= STEPPER_SPI.transfer((datagram >> 8) & 0xFF);
|
|
i_datagram <<= 8;
|
|
i_datagram |= STEPPER_SPI.transfer((datagram) & 0xFF);
|
|
i_datagram >>= 4;
|
|
|
|
#ifdef TMC_DEBUG1
|
|
//SERIAL_PRINTF("Received ");
|
|
//SERIAL_PRINTF("Received ", i_datagram,HEX);
|
|
//SERIAL_ECHOPAIR("\n\nReceived \n", i_datagram);
|
|
SERIAL_PRINTF("\n\nReceived %x", i_datagram);
|
|
debugLastStatus();
|
|
#endif
|
|
|
|
//deselect the TMC chip
|
|
extDigitalWrite(cs_pin, HIGH);
|
|
|
|
//restore the previous SPI mode if neccessary
|
|
//if the mode is not correct set it to mode 3
|
|
//if (oldMode != SPI_MODE3) {
|
|
// SPI.setDataMode(oldMode);
|
|
//}
|
|
|
|
//store the datagram as status result
|
|
driver_status_result = i_datagram;
|
|
}
|
|
|
|
#endif // HAS_DRIVER(TMC2660)
|
|
|
|
#endif // STM32GENERIC && STM32F7
|
|
|