You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
173 lines
5.2 KiB
173 lines
5.2 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
|
|
*/
|
|
|
|
#ifndef BOARD_INFO_NAME
|
|
#define BOARD_INFO_NAME "3Drag"
|
|
#endif
|
|
|
|
#ifndef DEFAULT_MACHINE_NAME
|
|
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
|
|
#endif
|
|
|
|
#ifndef DEFAULT_SOURCE_CODE_URL
|
|
#define DEFAULT_SOURCE_CODE_URL "3dprint.elettronicain.it"
|
|
#endif
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define Z_STOP_PIN 18
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#if HAS_CUTTER
|
|
#define Z_DIR_PIN 28
|
|
#define Z_ENABLE_PIN 24
|
|
#define Z_STEP_PIN 26
|
|
#else
|
|
#define Z_ENABLE_PIN 63
|
|
#endif
|
|
|
|
#if HAS_CUTTER && !HAS_EXTRUDERS
|
|
#define E0_DIR_PIN -1
|
|
#define E0_ENABLE_PIN -1
|
|
#define E0_STEP_PIN -1
|
|
#endif
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define MOSFET_B_PIN 8
|
|
#define MOSFET_C_PIN 9
|
|
#define MOSFET_D_PIN 12
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define SDSS 25
|
|
|
|
#ifndef CASE_LIGHT_PIN
|
|
#define CASE_LIGHT_PIN -1 // Hardware PWM but one is not available on expansion header
|
|
#endif
|
|
|
|
/**
|
|
* M3/M4/M5 - Spindle/Laser Control
|
|
*
|
|
* If you want to control the speed of your spindle then you'll have
|
|
* have to sacrifce the Extruder and pull some signals off the Z stepper
|
|
* driver socket.
|
|
*
|
|
* The following assumes:
|
|
* - the Z stepper driver socket is empty
|
|
* - the extruder driver socket has a driver board plugged into it
|
|
* - the Z stepper wires are attached the the extruder connector
|
|
*
|
|
* If you want to keep the extruder AND don't have a LCD display then
|
|
* you can still control the power on/off and spindle direction.
|
|
*
|
|
* Where to get spindle signals
|
|
*
|
|
* stepper signal socket name socket name
|
|
* -------
|
|
* SPINDLE_LASER_ENA_PIN /ENABLE O| |O VMOT
|
|
* MS1 O| |O GND
|
|
* MS2 O| |O 2B
|
|
* MS3 O| |O 2A
|
|
* /RESET O| |O 1A
|
|
* /SLEEP O| |O 1B
|
|
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
|
|
* SPINDLE_DIR_PIN DIR O| |O GND
|
|
* -------
|
|
*
|
|
* Note: Socket names vary from vendor to vendor
|
|
*/
|
|
#if HAS_CUTTER
|
|
#if !HAS_EXTRUDERS
|
|
#define SPINDLE_LASER_PWM_PIN 46 // Hardware PWM
|
|
#define SPINDLE_LASER_ENA_PIN 62 // Pullup!
|
|
#define SPINDLE_DIR_PIN 48
|
|
#elif !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // Use expansion header if no LCD in use
|
|
#define SPINDLE_LASER_ENA_PIN 16 // Pullup or pulldown!
|
|
#define SPINDLE_DIR_PIN 17
|
|
#if !NUM_SERVOS // Use servo connector if possible
|
|
#define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM
|
|
#elif HAS_FREE_AUX2_PINS
|
|
#define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM
|
|
#endif
|
|
#endif
|
|
#endif
|
|
|
|
#include "pins_RAMPS.h"
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_2_PIN 6
|
|
|
|
#undef SD_DETECT_PIN
|
|
#define SD_DETECT_PIN 53
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if IS_ULTRA_LCD && IS_NEWPANEL
|
|
#undef BEEPER_PIN
|
|
|
|
// TODO: Remap EXP1/2 based on adapter
|
|
#undef LCD_PINS_RS
|
|
#undef LCD_PINS_ENABLE
|
|
#undef LCD_PINS_D4
|
|
#undef LCD_PINS_D5
|
|
#undef LCD_PINS_D6
|
|
#undef LCD_PINS_D7
|
|
#define LCD_PINS_RS 27
|
|
#define LCD_PINS_ENABLE 29
|
|
#define LCD_PINS_D4 37
|
|
#define LCD_PINS_D5 35
|
|
#define LCD_PINS_D6 33
|
|
#define LCD_PINS_D7 31
|
|
|
|
// Buttons
|
|
#undef BTN_EN1
|
|
#undef BTN_EN2
|
|
#undef BTN_ENC
|
|
#define BTN_EN1 16
|
|
#define BTN_EN2 17
|
|
#define BTN_ENC 23
|
|
|
|
#else
|
|
|
|
#define BEEPER_PIN 33
|
|
|
|
#endif // IS_ULTRA_LCD && IS_NEWPANEL
|
|
|
|
#if IS_U8GLIB_ST7920
|
|
#define BOARD_ST7920_DELAY_1 0
|
|
#define BOARD_ST7920_DELAY_2 188
|
|
#define BOARD_ST7920_DELAY_3 0
|
|
#endif
|
|
|