/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * CREALITY 4.2.10 (STM32F103) board pin assignments */ #include "env_validate.h" #if HAS_MULTI_HOTEND || E_STEPPERS > 1 #error "CREALITY supports up to 1 hotends / E-steppers. Comment out this line to continue." #endif #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "Creality V4.2.10" #endif #ifndef DEFAULT_MACHINE_NAME #define DEFAULT_MACHINE_NAME "3DPrintMill" #endif #define BOARD_NO_NATIVE_USB // // EEPROM // #if NO_EEPROM_SELECTED // FLASH //#define FLASH_EEPROM_EMULATION // I2C #define IIC_BL24CXX_EEPROM // EEPROM on I2C-0 used only for display settings #if ENABLED(IIC_BL24CXX_EEPROM) #define IIC_EEPROM_SDA PA11 #define IIC_EEPROM_SCL PA12 #define MARLIN_EEPROM_SIZE 0x800 // 2Kb (24C16) #else #define SDCARD_EEPROM_EMULATION // SD EEPROM until all EEPROM is BL24CXX #define MARLIN_EEPROM_SIZE 0x800 // 2Kb #endif // SPI //#define SPI_EEPROM // EEPROM on SPI-0 //#define SPI_CHAN_EEPROM1 ? //#define SPI_EEPROM1_CS_PIN ? // 2K EEPROM //#define SPI_EEPROM2_CS_PIN ? // 32Mb FLASH //#define SPI_FLASH_CS_PIN ? #endif // // Servos // #define SERVO0_PIN PB0 // BLTouch OUT // // Limit Switches // #define X_STOP_PIN PA3 #define Y_STOP_PIN PA7 #define Z_STOP_PIN PA5 #define Z_MIN_PROBE_PIN PA5 // BLTouch IN // // Filament Runout Sensor // #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN PA6 // "Pulled-high" #endif // // Steppers // #define X_ENABLE_PIN PC3 #ifndef X_STEP_PIN #define X_STEP_PIN PC2 #endif #ifndef X_DIR_PIN #define X_DIR_PIN PB9 #endif #define Y_ENABLE_PIN PC3 #ifndef Y_STEP_PIN #define Y_STEP_PIN PB8 #endif #ifndef Y_DIR_PIN #define Y_DIR_PIN PB7 #endif #define Z_ENABLE_PIN PC3 #ifndef Z_STEP_PIN #define Z_STEP_PIN PB6 #endif #ifndef Z_DIR_PIN #define Z_DIR_PIN PB5 #endif #define E0_ENABLE_PIN PC3 #ifndef E0_STEP_PIN #define E0_STEP_PIN PB4 #endif #ifndef E0_DIR_PIN #define E0_DIR_PIN PB3 #endif // // Release PB4 (Y_ENABLE_PIN) from JTAG NRST role // #define DISABLE_DEBUG // // Temperature Sensors // #define TEMP_0_PIN PC5 // TH1 #define TEMP_BED_PIN PC4 // TB1 // // Heaters / Fans // #define HEATER_0_PIN PA0 // HEATER1 #define HEATER_BED_PIN PA1 // HOT BED #define FAN_PIN PA2 // FAN #define FAN_SOFT_PWM_REQUIRED // // SD Card // #define SD_DETECT_PIN PC7 #define SDCARD_CONNECTION ONBOARD #define ONBOARD_SPI_DEVICE 1 #define ONBOARD_SD_CS_PIN PA4 // SDSS #define SDIO_SUPPORT #define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer #if ENABLED(CR10_STOCKDISPLAY) #if ENABLED(RET6_12864_LCD) /** * RET6 12864 LCD * ------ * PC6 |10 9 | PB2 * PB10 | 8 7 | PE8 * PB14 6 5 | PB13 * PB12 | 4 3 | PB15 * GND | 2 1 | 5V * ------ * EXP1 */ #define EXP1_03_PIN PB15 #define EXP1_04_PIN PB12 #define EXP1_05_PIN PB13 #define EXP1_06_PIN PB14 #define EXP1_07_PIN PE8 #define EXP1_08_PIN PB10 #define EXP1_09_PIN PB2 #define EXP1_10_PIN PC6 #define BEEPER_PIN EXP1_10_PIN #elif ENABLED(VET6_12864_LCD) /** * VET6 12864 LCD * ------ * ? |10 9 | PC5 * PB10 | 8 7 | ? * PA6 6 5 | PA5 * PA4 | 4 3 | PA7 * GND | 2 1 | 5V * ------ * EXP1 */ #define EXP1_03_PIN PA7 #define EXP1_04_PIN PA4 #define EXP1_05_PIN PA5 #define EXP1_06_PIN PA6 #define EXP1_07_PIN -1 #define EXP1_08_PIN PB10 #define EXP1_09_PIN PC5 #define EXP1_10_PIN -1 #else #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller." #endif #define LCD_PINS_RS EXP1_04_PIN #define LCD_PINS_ENABLE EXP1_03_PIN #define LCD_PINS_D4 EXP1_05_PIN #define BTN_ENC EXP1_09_PIN #define BTN_EN1 EXP1_08_PIN #define BTN_EN2 EXP1_06_PIN #elif EITHER(HAS_DWIN_E3V2, IS_DWIN_MARLINUI) // RET6 DWIN ENCODER LCD #define BTN_ENC PB14 #define BTN_EN1 PB15 #define BTN_EN2 PB12 //#define LCD_LED_PIN PB2 #ifndef BEEPER_PIN #define BEEPER_PIN PB13 #endif #elif ENABLED(DWIN_VET6_CREALITY_LCD) // VET6 DWIN ENCODER LCD #define BTN_ENC PA6 #define BTN_EN1 PA7 #define BTN_EN2 PA4 #define BEEPER_PIN PA5 #endif