/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

#include "env_validate.h"

#define DEFAULT_MACHINE_NAME "3D Printer"

#define BOARD_INFO_NAME   "FYSETC Cheetah"
#define BOARD_WEBSITE_URL "fysetc.com"

// Ignore temp readings during development.
//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000

#define BOARD_NO_NATIVE_USB

#define DISABLE_JTAG

#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
  #define FLASH_EEPROM_EMULATION
  #define EEPROM_PAGE_SIZE     (0x800U)           // 2KB
  #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
  #define MARLIN_EEPROM_SIZE    EEPROM_PAGE_SIZE  // 2KB
#endif

//
// Servos
//
#define SERVO0_PIN                          PA0

//
// Limit Switches
//
#define X_STOP_PIN                          PA1
#define Y_STOP_PIN                          PB4
#define Z_STOP_PIN                          PA15

//
// Filament runout
//
#define FIL_RUNOUT_PIN                      PB5

//
// Steppers
//
#define X_STEP_PIN                          PB8
#define X_DIR_PIN                           PB9
#define X_ENABLE_PIN                        PA8

#define Y_STEP_PIN                          PB2
#define Y_DIR_PIN                           PB3
#define Y_ENABLE_PIN                        PB1

#define Z_STEP_PIN                          PC0
#define Z_DIR_PIN                           PC1
#define Z_ENABLE_PIN                        PC2

#define E0_STEP_PIN                         PC15
#define E0_DIR_PIN                          PC14
#define E0_ENABLE_PIN                       PC13

#if HAS_TMC_UART
  #define X_HARDWARE_SERIAL  MSerial2
  #define Y_HARDWARE_SERIAL  MSerial2
  #define Z_HARDWARE_SERIAL  MSerial2
  #define E0_HARDWARE_SERIAL MSerial2

  // Default TMC slave addresses
  #ifndef X_SLAVE_ADDRESS
    #define X_SLAVE_ADDRESS  0
  #endif
  #ifndef Y_SLAVE_ADDRESS
    #define Y_SLAVE_ADDRESS  1
  #endif
  #ifndef Z_SLAVE_ADDRESS
    #define Z_SLAVE_ADDRESS  2
  #endif
  #ifndef E0_SLAVE_ADDRESS
    #define E0_SLAVE_ADDRESS 3
  #endif
#endif

//
// Heaters / Fans
//
#define HEATER_0_PIN                        PC6
#define HEATER_BED_PIN                      PC7
#ifndef FAN_PIN
  #define FAN_PIN                           PC8
#endif

//
// Temperature Sensors
//
#define TEMP_BED_PIN                        PC5   // Analog Input
#define TEMP_0_PIN                          PC4   // Analog Input

//
// Misc. Functions
//
#define SDSS                                PA4
#define SD_DETECT_PIN                       PC3

#ifndef RGB_LED_R_PIN
  #define RGB_LED_R_PIN                     PB0
#endif
#ifndef RGB_LED_G_PIN
  #define RGB_LED_G_PIN                     PB7
#endif
#ifndef RGB_LED_B_PIN
  #define RGB_LED_B_PIN                     PB6
#endif

/*
* EXP1 pinout for the LCD according to Fysetcs schematic for the Cheetah board
*                 -----
*  (BEEPER) PC9  | 1 2 | PC12 (BTN_ENC)
* (BTN_EN2) PC11 | 3 4 | PB14 (LCD_RS / MISO)
* (BTN_EN1) PC10   5 6 | PB13 (SCK)
*  (LCD_EN) PB12 | 7 8 | PB15 (MOSI)
*            GND | 9 10| 5V
*                 -----
*                 EXP1
* Note: The pin-numbers match the connector correctly and are not in reverse order like on the Ender-3 board.
* Note: Functionally the pins are assigned in the same order as on the Ender-3 board.
* Note: Pin 4 on the Cheetah board is assigned to an I/O, it is assigned to RESET on the Ender-3 board.
*/

#if HAS_WIRED_LCD
  #define BEEPER_PIN                        PC9

  #if HAS_MARLINUI_U8GLIB
    #define DOGLCD_A0                       PB14
    #define DOGLCD_CS                       PB12
    #define DOGLCD_SCK                      PB13
    #define DOGLCD_MOSI                     PB15
    //#define LCD_SCREEN_ROT_90
    //#define LCD_SCREEN_ROT_180
    //#define LCD_SCREEN_ROT_270

    #if EITHER(FYSETC_MINI_12864, U8GLIB_ST7920)
      #define FORCE_SOFT_SPI
    #endif
  #endif

  #define LCD_PINS_RS                       PB12  // CS -- SOFT SPI for ENDER3 LCD
  #define LCD_PINS_D4                       PB13  // SCLK
  #define LCD_PINS_ENABLE                   PB15  // DATA MOSI

  //#define LCD_CONTRAST_INIT                190

  #if IS_NEWPANEL
    #define BTN_EN1                         PC10
    #define BTN_EN2                         PC11
    #define BTN_ENC                         PC12
  #endif
#endif

#if ENABLED(TOUCH_UI_FTDI_EVE)
  #define BEEPER_PIN                        PC9
  #define CLCD_MOD_RESET                    PC11
  #define CLCD_SPI_CS                       PB12

  //#define CLCD_USE_SOFT_SPI                     // the Cheetah can use hardware-SPI so we do not really need this

  #if ENABLED(CLCD_USE_SOFT_SPI)
    #define CLCD_SOFT_SPI_MOSI              PB15
    #define CLCD_SOFT_SPI_MISO              PB14
    #define CLCD_SOFT_SPI_SCLK              PB13
  #else
    #define CLCD_SPI_BUS                       2
  #endif
#endif