/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * SanityCheck.h * * Test configuration values for errors at compile-time. */ /** * Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features. */ #if __cplusplus < 201103L #error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain." #endif // Make sure macros aren't borked #define TEST1 #define TEST2 1 #define TEST3 0 #define TEST4 true #if ENABLED(TEST0) #error "ENABLED is borked!" #endif #if DISABLED(TEST1) #error "DISABLED is borked!" #endif #if !ENABLED(TEST2) #error "ENABLED is borked!" #endif #if ENABLED(TEST3) #error "ENABLED is borked!" #endif #if DISABLED(TEST4) #error "DISABLED is borked!" #endif #if !ANY(TEST1, TEST2, TEST3, TEST4) || ANY(TEST0, TEST3) #error "ANY is borked!" #endif #if DISABLED(TEST0, TEST1, TEST2, TEST4) #error "DISABLED is borked!" #endif #undef TEST1 #undef TEST2 #undef TEST3 #undef TEST4 /** * We try our best to include sanity checks for all changed configuration * directives because users have a tendency to use outdated config files with * the bleeding-edge source code, but sometimes this is not enough. This check * forces a minimum config file revision. Otherwise Marlin will not build. */ #define HEXIFY(H) _CAT(0x,H) #if !defined(CONFIGURATION_H_VERSION) || HEXIFY(CONFIGURATION_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_H_VERSION) #error "You are using an old Configuration.h file, update it before building Marlin." #endif #if !defined(CONFIGURATION_ADV_H_VERSION) || HEXIFY(CONFIGURATION_ADV_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_ADV_H_VERSION) #error "You are using an old Configuration_adv.h file, update it before building Marlin." #endif #undef HEXIFY /** * Warnings for old configurations */ #ifndef MOTHERBOARD #error "MOTHERBOARD is required. Please update your configuration." #elif !defined(X_BED_SIZE) || !defined(Y_BED_SIZE) #error "X_BED_SIZE and Y_BED_SIZE are now required! Please update your configuration." #elif WATCH_TEMP_PERIOD > 500 #error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds." #elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD)) #error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS." #elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD) #error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED." #elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE) #error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY." #elif defined(X_HOME_RETRACT_MM) #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM." #elif defined(SDCARDDETECTINVERTED) #error "SDCARDDETECTINVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #elif defined(SD_DETECT_INVERTED) #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #elif defined(BTENABLED) #error "BTENABLED is now BLUETOOTH. Please update your configuration." #elif defined(CUSTOM_MENDEL_NAME) #error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration." #elif defined(HAS_AUTOMATIC_VERSIONING) #error "HAS_AUTOMATIC_VERSIONING is now CUSTOM_VERSION_FILE. Please update your configuration." #elif defined(USE_AUTOMATIC_VERSIONING) #error "USE_AUTOMATIC_VERSIONING is now CUSTOM_VERSION_FILE. Please update your configuration." #elif defined(SDSLOW) #error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead." #elif defined(SDEXTRASLOW) #error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead." #elif defined(FILAMENT_SENSOR) #error "FILAMENT_SENSOR is now FILAMENT_WIDTH_SENSOR. Please update your configuration." #elif defined(ENDSTOPPULLUP_FIL_RUNOUT) #error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULLUP. Please update your configuration." #elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS) #error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead." #elif defined(LANGUAGE_INCLUDE) #error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration." #elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y) #error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead." #elif defined(PID_PARAMS_PER_EXTRUDER) #error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead." #elif defined(EXTRUDER_WATTS) || defined(BED_WATTS) #error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration." #elif defined(SERVO_ENDSTOP_ANGLES) #error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead." #elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR) #error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed." #elif defined(Z_ENDSTOP_SERVO_NR) #error "Z_ENDSTOP_SERVO_NR is now Z_PROBE_SERVO_NR. Please update your configuration." #elif defined(DEFAULT_XYJERK) #error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead." #elif defined(XY_TRAVEL_SPEED) #error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead." #elif defined(PROBE_SERVO_DEACTIVATION_DELAY) #error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead." #elif defined(SERVO_DEACTIVATION_DELAY) #error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead." #elif ENABLED(FILAMENTCHANGEENABLE) #error "FILAMENTCHANGEENABLE is now ADVANCED_PAUSE_FEATURE. Please update your configuration." #elif ENABLED(FILAMENT_CHANGE_FEATURE) #error "FILAMENT_CHANGE_FEATURE is now ADVANCED_PAUSE_FEATURE. Please update your configuration." #elif defined(FILAMENT_CHANGE_X_POS) || defined(FILAMENT_CHANGE_Y_POS) #error "FILAMENT_CHANGE_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(FILAMENT_CHANGE_Z_ADD) #error "FILAMENT_CHANGE_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(FILAMENT_CHANGE_XY_FEEDRATE) #error "FILAMENT_CHANGE_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_Z_FEEDRATE) #error "FILAMENT_CHANGE_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration." #elif defined(PAUSE_PARK_X_POS) || defined(PAUSE_PARK_Y_POS) #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(PAUSE_PARK_Z_ADD) #error "PAUSE_PARK_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(PAUSE_PARK_XY_FEEDRATE) #error "PAUSE_PARK_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration." #elif defined(PAUSE_PARK_Z_FEEDRATE) #error "PAUSE_PARK_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_RETRACT_FEEDRATE) #error "FILAMENT_CHANGE_RETRACT_FEEDRATE is now PAUSE_PARK_RETRACT_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_RETRACT_LENGTH) #error "FILAMENT_CHANGE_RETRACT_LENGTH is now PAUSE_PARK_RETRACT_LENGTH. Please update your configuration." #elif defined(FILAMENT_CHANGE_EXTRUDE_FEEDRATE) #error "FILAMENT_CHANGE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration." #elif defined(ADVANCED_PAUSE_EXTRUDE_FEEDRATE) #error "ADVANCED_PAUSE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_EXTRUDE_LENGTH) #error "FILAMENT_CHANGE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration." #elif defined(ADVANCED_PAUSE_EXTRUDE_LENGTH) #error "ADVANCED_PAUSE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration." #elif defined(FILAMENT_CHANGE_NOZZLE_TIMEOUT) #error "FILAMENT_CHANGE_NOZZLE_TIMEOUT is now PAUSE_PARK_NOZZLE_TIMEOUT. Please update your configuration." #elif defined(FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS) #error "FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS is now FILAMENT_CHANGE_ALERT_BEEPS. Please update your configuration." #elif defined(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT) #error "FILAMENT_CHANGE_NO_STEPPER_TIMEOUT is now PAUSE_PARK_NO_STEPPER_TIMEOUT. Please update your configuration." #elif defined(PLA_PREHEAT_HOTEND_TEMP) #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration." #elif defined(PLA_PREHEAT_HPB_TEMP) #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration." #elif defined(PLA_PREHEAT_FAN_SPEED) #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration." #elif defined(ABS_PREHEAT_HOTEND_TEMP) #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration." #elif defined(ABS_PREHEAT_HPB_TEMP) #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration." #elif defined(ABS_PREHEAT_FAN_SPEED) #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration." #elif defined(ENDSTOPS_ONLY_FOR_HOMING) #error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead." #elif defined(HOMING_FEEDRATE) #error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead." #elif defined(MANUAL_HOME_POSITIONS) #error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead." #elif defined(PID_ADD_EXTRUSION_RATE) #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration." #elif defined(Z_RAISE_BEFORE_HOMING) #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration." #elif defined(MIN_Z_HEIGHT_FOR_HOMING) #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration." #elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING) #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE and Z_AFTER_PROBING instead." #elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS) #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration." #elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT) #error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration." #elif defined(MANUAL_BED_LEVELING) #error "MANUAL_BED_LEVELING is now LCD_BED_LEVELING. Please update your configuration." #elif defined(MESH_HOME_SEARCH_Z) #error "MESH_HOME_SEARCH_Z is now LCD_PROBE_Z_RANGE. Please update your configuration." #elif defined(MANUAL_PROBE_Z_RANGE) #error "MANUAL_PROBE_Z_RANGE is now LCD_PROBE_Z_RANGE. Please update your configuration." #elif !defined(MIN_STEPS_PER_SEGMENT) #error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h. #elif MIN_STEPS_PER_SEGMENT <= 0 #error "MIN_STEPS_PER_SEGMENT must be at least 1. Please update your Configuration_adv.h." #elif defined(PREVENT_DANGEROUS_EXTRUDE) #error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration." #elif defined(SCARA) #error "SCARA is now MORGAN_SCARA. Please update your configuration." #elif defined(ENABLE_AUTO_BED_LEVELING) #error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT." #elif defined(AUTO_BED_LEVELING_FEATURE) #error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT." #elif defined(ABL_GRID_POINTS) #error "ABL_GRID_POINTS is now GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y. Please update your configuration." #elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y) #error "ABL_GRID_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(ABL_GRID_MAX_POINTS_X) || defined(ABL_GRID_MAX_POINTS_Y) #error "ABL_GRID_MAX_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(MESH_NUM_X_POINTS) || defined(MESH_NUM_Y_POINTS) #error "MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(UBL_MESH_NUM_X_POINTS) || defined(UBL_MESH_NUM_Y_POINTS) #error "UBL_MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(UBL_G26_MESH_VALIDATION) #error "UBL_G26_MESH_VALIDATION is now G26_MESH_VALIDATION. Please update your configuration." #elif defined(UBL_MESH_EDIT_ENABLED) #error "UBL_MESH_EDIT_ENABLED is now G26_MESH_VALIDATION. Please update your configuration." #elif defined(UBL_MESH_EDITING) #error "UBL_MESH_EDITING is now G26_MESH_VALIDATION. Please update your configuration." #elif defined(BLTOUCH_HEATERS_OFF) #error "BLTOUCH_HEATERS_OFF is now PROBING_HEATERS_OFF. Please update your configuration." #elif defined(BLTOUCH_V3) #error "BLTOUCH_V3 is obsolete. Please update your configuration." #elif defined(BLTOUCH_FORCE_OPEN_DRAIN_MODE) #error "BLTOUCH_FORCE_OPEN_DRAIN_MODE is obsolete. Please update your configuration." #elif defined(BEEPER) #error "BEEPER is now BEEPER_PIN. Please update your pins definitions." #elif defined(SDCARDDETECT) #error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions." #elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE) #error "STAT_LED_RED/STAT_LED_BLUE are now STAT_LED_RED_PIN/STAT_LED_BLUE_PIN. Please update your pins definitions." #elif defined(LCD_PIN_BL) #error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN. Please update your pins definitions." #elif defined(LCD_PIN_RESET) #error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions." #elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN) #error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h." #elif defined(PID_FAN_SCALING) && !HAS_FAN #error "PID_FAN_SCALING needs at least one fan enabled." #elif defined(min_software_endstops) || defined(max_software_endstops) #error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration." #elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN) #error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)." #elif defined(CONTROLLERFAN_PIN) #error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h." #elif defined(CONTROLLERFAN_SPEED) #error "CONTROLLERFAN_SPEED is now CONTROLLERFAN_SPEED_ACTIVE. Please update your Configuration_adv.h." #elif defined(CONTROLLERFAN_SECS) #error "CONTROLLERFAN_SECS is now CONTROLLERFAN_IDLE_TIME. Please update your Configuration_adv.h." #elif defined(MIN_RETRACT) #error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h." #elif defined(ADVANCE) #error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE." #elif defined(LIN_ADVANCE_E_D_RATIO) #error "LIN_ADVANCE (1.5) no longer uses LIN_ADVANCE_E_D_RATIO. Check your configuration." #elif defined(NEOPIXEL_RGBW_LED) #error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration." #elif ENABLED(DELTA) && defined(DELTA_PROBEABLE_RADIUS) #error "Remove DELTA_PROBEABLE_RADIUS and use PROBING_MARGIN to inset the probe area instead." #elif ENABLED(DELTA) && defined(DELTA_CALIBRATION_RADIUS) #error "Remove DELTA_CALIBRATION_RADIUS and use PROBING_MARGIN to inset the probe area instead." #elif defined(UBL_MESH_INSET) #error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration." #elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y) #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration." #elif defined(ABL_PROBE_PT_1_X) || defined(ABL_PROBE_PT_1_Y) || defined(ABL_PROBE_PT_2_X) || defined(ABL_PROBE_PT_2_Y) || defined(ABL_PROBE_PT_3_X) || defined(ABL_PROBE_PT_3_Y) #error "ABL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h." #elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y) #error "UBL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h." #elif defined(MIN_PROBE_EDGE) #error "MIN_PROBE_EDGE is now called PROBING_MARGIN. Please update your configuration." #elif defined(MIN_PROBE_EDGE_LEFT) #error "MIN_PROBE_EDGE_LEFT is now called PROBING_MARGIN_LEFT. Please update your configuration." #elif defined(MIN_PROBE_EDGE_RIGHT) #error "MIN_PROBE_EDGE_RIGHT is now called PROBING_MARGIN_RIGHT. Please update your configuration." #elif defined(MIN_PROBE_EDGE_FRONT) #error "MIN_PROBE_EDGE_FRONT is now called PROBING_MARGIN_FRONT. Please update your configuration." #elif defined(MIN_PROBE_EDGE_BACK) #error "MIN_PROBE_EDGE_BACK is now called PROBING_MARGIN_BACK. Please update your configuration." #elif defined(LEFT_PROBE_BED_POSITION) #error "LEFT_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_LEFT instead." #elif defined(RIGHT_PROBE_BED_POSITION) #error "RIGHT_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_RIGHT instead." #elif defined(FRONT_PROBE_BED_POSITION) #error "FRONT_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_FRONT instead." #elif defined(BACK_PROBE_BED_POSITION) #error "BACK_PROBE_BED_POSITION is obsolete. Set a margin with PROBING_MARGIN or PROBING_MARGIN_BACK instead." #elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY) #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration." #elif defined(BABYSTEP_ZPROBE_GFX_REVERSE) #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations." #elif defined(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN) #error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES. Please update your configuration." #elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1)) #error "K1 is now PID_K1. Please update your configuration." #elif defined(PROBE_DOUBLE_TOUCH) #error "PROBE_DOUBLE_TOUCH is now MULTIPLE_PROBING. Please update your configuration." #elif defined(ANET_KEYPAD_LCD) #error "ANET_KEYPAD_LCD is now ZONESTAR_LCD. Please update your configuration." #elif defined(LCD_I2C_SAINSMART_YWROBOT) #error "LCD_I2C_SAINSMART_YWROBOT is now LCD_SAINSMART_I2C_(1602|2004). Please update your configuration." #elif defined(MEASURED_LOWER_LIMIT) || defined(MEASURED_UPPER_LIMIT) #error "MEASURED_(UPPER|LOWER)_LIMIT is now FILWIDTH_ERROR_MARGIN. Please update your configuration." #elif defined(HAVE_TMCDRIVER) #error "HAVE_TMCDRIVER is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h." #elif defined(STEALTHCHOP) #error "STEALTHCHOP is now STEALTHCHOP_(XY|Z|E). Please update your Configuration_adv.h." #elif defined(HAVE_TMC26X) #error "HAVE_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h." #elif defined(HAVE_TMC2130) #error "HAVE_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h." #elif defined(HAVE_TMC2208) #error "HAVE_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h." #elif defined(HAVE_L6470DRIVER) #error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h." #elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \ || defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) || defined(E5_IS_TMC) || defined(E6_IS_TMC) || defined(E7_IS_TMC) #error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h." #elif defined(X_IS_TMC26X) || defined(X2_IS_TMC26X) || defined(Y_IS_TMC26X) || defined(Y2_IS_TMC26X) || defined(Z_IS_TMC26X) || defined(Z2_IS_TMC26X) || defined(Z3_IS_TMC26X) \ || defined(E0_IS_TMC26X) || defined(E1_IS_TMC26X) || defined(E2_IS_TMC26X) || defined(E3_IS_TMC26X) || defined(E4_IS_TMC26X) || defined(E5_IS_TMC26X) || defined(E6_IS_TMC26X) || defined(E7_IS_TMC26X) #error "[AXIS]_IS_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h." #elif defined(X_IS_TMC2130) || defined(X2_IS_TMC2130) || defined(Y_IS_TMC2130) || defined(Y2_IS_TMC2130) || defined(Z_IS_TMC2130) || defined(Z2_IS_TMC2130) || defined(Z3_IS_TMC2130) \ || defined(E0_IS_TMC2130) || defined(E1_IS_TMC2130) || defined(E2_IS_TMC2130) || defined(E3_IS_TMC2130) || defined(E4_IS_TMC2130) || defined(E5_IS_TMC2130) || defined(E6_IS_TMC2130) || defined(E7_IS_TMC2130) #error "[AXIS]_IS_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h." #elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \ || defined(E0_IS_TMC2208) || defined(E1_IS_TMC2208) || defined(E2_IS_TMC2208) || defined(E3_IS_TMC2208) || defined(E4_IS_TMC2208) || defined(E5_IS_TMC2208) || defined(E6_IS_TMC2208) || defined(E7_IS_TMC2208) #error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h." #elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \ || defined(E0_IS_L6470) || defined(E1_IS_L6470) || defined(E2_IS_L6470) || defined(E3_IS_L6470) || defined(E4_IS_L6470) || defined(E5_IS_L6470) || defined(E6_IS_L6470) || defined(E7_IS_L6470) #error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h." #elif defined(AUTOMATIC_CURRENT_CONTROL) #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration." #elif defined(FILAMENT_CHANGE_LOAD_LENGTH) #error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH. Please update your configuration." #elif defined(LEVEL_CORNERS_INSET) #error "LEVEL_CORNERS_INSET is now LEVEL_CORNERS_INSET_LFRB . Please update your Configuration.h." #elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET_LFRB) #error "LEVEL_BED_CORNERS requires LEVEL_CORNERS_INSET_LFRB values. Please update your Configuration.h." #elif defined(BEZIER_JERK_CONTROL) #error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION. Please update your configuration." #elif HAS_JUNCTION_DEVIATION && defined(JUNCTION_DEVIATION_FACTOR) #error "JUNCTION_DEVIATION_FACTOR is now JUNCTION_DEVIATION_MM. Please update your configuration." #elif defined(JUNCTION_ACCELERATION_FACTOR) #error "JUNCTION_ACCELERATION_FACTOR is obsolete. Delete it from Configuration_adv.h." #elif defined(JUNCTION_ACCELERATION) #error "JUNCTION_ACCELERATION is obsolete. Delete it from Configuration_adv.h." #elif defined(MAX7219_DEBUG_STEPPER_HEAD) #error "MAX7219_DEBUG_STEPPER_HEAD is now MAX7219_DEBUG_PLANNER_HEAD. Please update your configuration." #elif defined(MAX7219_DEBUG_STEPPER_TAIL) #error "MAX7219_DEBUG_STEPPER_TAIL is now MAX7219_DEBUG_PLANNER_TAIL. Please update your configuration." #elif defined(MAX7219_DEBUG_STEPPER_QUEUE) #error "MAX7219_DEBUG_STEPPER_QUEUE is now MAX7219_DEBUG_PLANNER_QUEUE. Please update your configuration." #elif defined(ENDSTOP_NOISE_FILTER) #error "ENDSTOP_NOISE_FILTER is now ENDSTOP_NOISE_THRESHOLD [2-7]. Please update your configuration." #elif defined(RETRACT_ZLIFT) #error "RETRACT_ZLIFT is now RETRACT_ZRAISE. Please update your Configuration_adv.h." #elif defined(TOOLCHANGE_PARK_ZLIFT) || defined(TOOLCHANGE_UNPARK_ZLIFT) #error "TOOLCHANGE_PARK_ZLIFT and TOOLCHANGE_UNPARK_ZLIFT are now TOOLCHANGE_ZRAISE. Please update your configuration." #elif defined(SINGLENOZZLE_TOOLCHANGE_ZRAISE) #error "SINGLENOZZLE_TOOLCHANGE_ZRAISE is now TOOLCHANGE_ZRAISE. Please update your configuration." #elif defined(SINGLENOZZLE_SWAP_LENGTH) #error "SINGLENOZZLE_SWAP_LENGTH is now TOOLCHANGE_FIL_SWAP_LENGTH. Please update your configuration." #elif defined(SINGLENOZZLE_SWAP_RETRACT_SPEED) #error "SINGLENOZZLE_SWAP_RETRACT_SPEED is now TOOLCHANGE_FIL_SWAP_RETRACT_SPEED. Please update your configuration." #elif defined(SINGLENOZZLE_SWAP_PRIME_SPEED) #error "SINGLENOZZLE_SWAP_PRIME_SPEED is now TOOLCHANGE_FIL_SWAP_PRIME_SPEED. Please update your configuration." #elif defined(SINGLENOZZLE_SWAP_PARK) #error "SINGLENOZZLE_SWAP_PARK is now TOOLCHANGE_PARK. Please update your configuration." #elif defined(SINGLENOZZLE_TOOLCHANGE_XY) #error "SINGLENOZZLE_TOOLCHANGE_XY is now TOOLCHANGE_PARK_XY. Please update your configuration." #elif defined(SINGLENOZZLE_PARK_XY_FEEDRATE) #error "SINGLENOZZLE_PARK_XY_FEEDRATE is now TOOLCHANGE_PARK_XY_FEEDRATE. Please update your configuration." #elif defined(PARKING_EXTRUDER_SECURITY_RAISE) #error "PARKING_EXTRUDER_SECURITY_RAISE is now TOOLCHANGE_ZRAISE. Please update your configuration." #elif defined(SWITCHING_TOOLHEAD_SECURITY_RAISE) #error "SWITCHING_TOOLHEAD_SECURITY_RAISE is now TOOLCHANGE_ZRAISE. Please update your configuration." #elif defined(G0_FEEDRATE) && G0_FEEDRATE == 0 #error "G0_FEEDRATE is now used to set the G0 feedrate. Please update your configuration." #elif defined(MBL_Z_STEP) #error "MBL_Z_STEP is now MESH_EDIT_Z_STEP. Please update your configuration." #elif defined(CHDK) #error "CHDK is now CHDK_PIN. Please update your Configuration_adv.h." #elif defined(MAX6675_SS) #error "MAX6675_SS is now MAX6675_SS_PIN. Please update your configuration and/or pins." #elif defined(MAX6675_SS2) #error "MAX6675_SS2 is now MAX6675_SS2_PIN. Please update your configuration and/or pins." #elif defined(SPINDLE_LASER_ENABLE) #error "SPINDLE_LASER_ENABLE is now SPINDLE_FEATURE or LASER_FEATURE. Please update your Configuration_adv.h." #elif defined(SPINDLE_LASER_ENABLE_PIN) #error "SPINDLE_LASER_ENABLE_PIN is now SPINDLE_LASER_ENA_PIN. Please update your Configuration_adv.h and/or pins." #elif defined(SPINDLE_DIR_CHANGE) #error "SPINDLE_DIR_CHANGE is now SPINDLE_CHANGE_DIR. Please update your Configuration_adv.h." #elif defined(SPINDLE_STOP_ON_DIR_CHANGE) #error "SPINDLE_STOP_ON_DIR_CHANGE is now SPINDLE_CHANGE_DIR_STOP. Please update your Configuration_adv.h." #elif defined(SPINDLE_LASER_ENABLE_INVERT) #error "SPINDLE_LASER_ENABLE_INVERT is now SPINDLE_LASER_ACTIVE_HIGH. Please update your Configuration_adv.h." #elif defined(CUTTER_POWER_DISPLAY) #error "CUTTER_POWER_DISPLAY is now CUTTER_POWER_UNIT. Please update your Configuration_adv.h." #elif defined(CHAMBER_HEATER_PIN) #error "CHAMBER_HEATER_PIN is now HEATER_CHAMBER_PIN. Please update your configuration and/or pins." #elif defined(TMC_Z_CALIBRATION) #error "TMC_Z_CALIBRATION has been deprecated in favor of Z_STEPPER_AUTO_ALIGN. Please update your configuration." #elif defined(Z_MIN_PROBE_ENDSTOP) #error "Z_MIN_PROBE_ENDSTOP is no longer required. Please remove it from Configuration.h." #elif defined(DUAL_NOZZLE_DUPLICATION_MODE) #error "DUAL_NOZZLE_DUPLICATION_MODE is now MULTI_NOZZLE_DUPLICATION. Please update your configuration." #elif defined(MENU_ITEM_CASE_LIGHT) #error "MENU_ITEM_CASE_LIGHT is now CASE_LIGHT_MENU. Please update your configuration." #elif defined(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) #error "ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED is now SD_ABORT_ON_ENDSTOP_HIT. Please update your Configuration_adv.h." #elif defined(LPC_SD_LCD) || defined(LPC_SD_ONBOARD) || defined(LPC_SD_CUSTOM_CABLE) #error "LPC_SD_(LCD|ONBOARD|CUSTOM_CABLE) are now SDCARD_CONNECTION. Please update your Configuration_adv.h." #elif defined(USB_SD_DISABLED) #error "USB_SD_DISABLED is now NO_SD_HOST_DRIVE. Please update your Configuration_adv.h." #elif defined(USB_SD_ONBOARD) #error "USB_SD_ONBOARD is obsolete. Disable NO_SD_HOST_DRIVE instead." #elif POWER_SUPPLY == 1 #error "Replace POWER_SUPPLY 1 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'false'." #elif POWER_SUPPLY == 2 #error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'true'." #elif defined(POWER_SUPPLY) #error "POWER_SUPPLY is now obsolete. Please remove it from Configuration.h." #elif defined(MKS_ROBIN_TFT) #error "MKS_ROBIN_TFT is now FSMC_GRAPHICAL_TFT. Please update your configuration." #elif defined(TFT_LVGL_UI) #error "TFT_LVGL_UI is now TFT_LVGL_UI_FSMC. Please update your configuration." #elif defined(SDPOWER) #error "SDPOWER is now SDPOWER_PIN. Please update your configuration and/or pins." #elif defined(STRING_SPLASH_LINE1) || defined(STRING_SPLASH_LINE2) #error "STRING_SPLASH_LINE[12] are now obsolete. Please remove them from Configuration.h." #elif defined(Z_PROBE_ALLEN_KEY_DEPLOY_1_X) || defined(Z_PROBE_ALLEN_KEY_STOW_1_X) #error "Z_PROBE_ALLEN_KEY_(DEPLOY|STOW) coordinates are now a single setting. Please update your configuration." #elif defined(X_PROBE_OFFSET_FROM_EXTRUDER) || defined(Y_PROBE_OFFSET_FROM_EXTRUDER) || defined(Z_PROBE_OFFSET_FROM_EXTRUDER) #error "[XYZ]_PROBE_OFFSET_FROM_EXTRUDER is now NOZZLE_TO_PROBE_OFFSET. Please update your configuration." #elif defined(MIN_PROBE_X) || defined(MIN_PROBE_Y) || defined(MAX_PROBE_X) || defined(MAX_PROBE_Y) #error "(MIN|MAX)_PROBE_[XY] are now calculated at runtime. Please remove them from Configuration.h." #elif defined(Z_STEPPER_ALIGN_X) || defined(Z_STEPPER_ALIGN_X) #error "Z_STEPPER_ALIGN_X and Z_STEPPER_ALIGN_Y are now combined as Z_STEPPER_ALIGN_XY. Please update your Configuration_adv.h." #elif defined(JUNCTION_DEVIATION) #error "JUNCTION_DEVIATION is no longer required. (See CLASSIC_JERK). Please remove it from Configuration.h." #elif defined(BABYSTEP_MULTIPLICATOR) #error "BABYSTEP_MULTIPLICATOR is now BABYSTEP_MULTIPLICATOR_[XY|Z]. Please update Configuration_adv.h." #elif defined(LULZBOT_TOUCH_UI) #error "LULZBOT_TOUCH_UI is now TOUCH_UI_FTDI_EVE. Please update your configuration." #elif defined(PS_DEFAULT_OFF) #error "PS_DEFAULT_OFF is now PSU_DEFAULT_OFF. Please update your configuration." #elif defined(FILAMENT_UNLOAD_RETRACT_LENGTH) #error "FILAMENT_UNLOAD_RETRACT_LENGTH is now FILAMENT_UNLOAD_PURGE_RETRACT. Please update Configuration_adv.h." #elif defined(FILAMENT_UNLOAD_DELAY) #error "FILAMENT_UNLOAD_DELAY is now FILAMENT_UNLOAD_PURGE_DELAY. Please update Configuration_adv.h." #elif defined(HOME_USING_SPREADCYCLE) #error "HOME_USING_SPREADCYCLE is now obsolete. Please remove it from Configuration_adv.h." #elif defined(DGUS_LCD) #error "DGUS_LCD is now DGUS_LCD_UI_(ORIGIN|FYSETC|HIPRECY). Please update your configuration." #elif defined(X_DUAL_ENDSTOPS_ADJUSTMENT) #error "X_DUAL_ENDSTOPS_ADJUSTMENT is now X2_ENDSTOP_ADJUSTMENT. Please update Configuration_adv.h." #elif defined(Y_DUAL_ENDSTOPS_ADJUSTMENT) #error "Y_DUAL_ENDSTOPS_ADJUSTMENT is now Y2_ENDSTOP_ADJUSTMENT. Please update Configuration_adv.h." #elif defined(Z_DUAL_ENDSTOPS_ADJUSTMENT) #error "Z_DUAL_ENDSTOPS_ADJUSTMENT is now Z2_ENDSTOP_ADJUSTMENT. Please update Configuration_adv.h." #elif defined(Z_TRIPLE_ENDSTOPS_ADJUSTMENT2) || defined(Z_TRIPLE_ENDSTOPS_ADJUSTMENT3) #error "Z_TRIPLE_ENDSTOPS_ADJUSTMENT[23] is now Z[23]_ENDSTOP_ADJUSTMENT. Please update Configuration_adv.h." #elif defined(Z_QUAD_ENDSTOPS_ADJUSTMENT2) || defined(Z_QUAD_ENDSTOPS_ADJUSTMENT3) || defined(Z_QUAD_ENDSTOPS_ADJUSTMENT4) #error "Z_QUAD_ENDSTOPS_ADJUSTMENT[234] is now Z[234]_ENDSTOP_ADJUSTMENT. Please update Configuration_adv.h." #elif defined(Z_DUAL_STEPPER_DRIVERS) #error "Z_DUAL_STEPPER_DRIVERS is now NUM_Z_STEPPER_DRIVERS with a value of 2. Please update Configuration_adv.h." #elif defined(Z_TRIPLE_STEPPER_DRIVERS) #error "Z_TRIPLE_STEPPER_DRIVERS is now NUM_Z_STEPPER_DRIVERS with a value of 3. Please update Configuration_adv.h." #elif defined(Z_QUAD_STEPPER_DRIVERS) #error "Z_QUAD_STEPPER_DRIVERS is now NUM_Z_STEPPER_DRIVERS with a value of 4. Please update Configuration_adv.h." #elif defined(Z_DUAL_ENDSTOPS) #error "Z_DUAL_ENDSTOPS is now Z_MULTI_ENDSTOPS. Please update Configuration_adv.h." #elif defined(Z_TRIPLE_ENDSTOPS) #error "Z_TRIPLE_ENDSTOPS is now Z_MULTI_ENDSTOPS. Please update Configuration_adv.h." #elif defined(Z_QUAD_ENDSTOPS) #error "Z_QUAD_ENDSTOPS is now Z_MULTI_ENDSTOPS. Please update Configuration_adv.h." #elif defined(DUGS_UI_MOVE_DIS_OPTION) #error "DUGS_UI_MOVE_DIS_OPTION is spelled DGUS_UI_MOVE_DIS_OPTION. Please update Configuration_adv.h." #elif defined(ORIG_E0_AUTO_FAN_PIN) || defined(ORIG_E1_AUTO_FAN_PIN) || defined(ORIG_E2_AUTO_FAN_PIN) || defined(ORIG_E3_AUTO_FAN_PIN) || defined(ORIG_E4_AUTO_FAN_PIN) || defined(ORIG_E5_AUTO_FAN_PIN) || defined(ORIG_E6_AUTO_FAN_PIN) || defined(ORIG_E7_AUTO_FAN_PIN) #error "ORIG_Ex_AUTO_FAN_PIN is now just Ex_AUTO_FAN_PIN. Make sure your pins are up to date." #elif defined(ORIG_CHAMBER_AUTO_FAN_PIN) #error "ORIG_CHAMBER_AUTO_FAN_PIN is now just CHAMBER_AUTO_FAN_PIN. Make sure your pins are up to date." #elif defined(HOMING_BACKOFF_MM) #error "HOMING_BACKOFF_MM is now HOMING_BACKOFF_POST_MM. Please update Configuration_adv.h." #elif defined(X_HOME_BUMP_MM) || defined(Y_HOME_BUMP_MM) || defined(Z_HOME_BUMP_MM) #error "[XYZ]_HOME_BUMP_MM is now HOMING_BUMP_MM. Please update Configuration_adv.h." #elif defined(DIGIPOT_I2C) #error "DIGIPOT_I2C is now DIGIPOT_MCP4451 (or DIGIPOT_MCP4018). Please update Configuration_adv.h." #elif defined(TOUCH_BUTTONS) #error "TOUCH_BUTTONS is now TOUCH_SCREEN. Please update your Configuration.h." #elif defined(ANYCUBIC_TFT_MODEL) #error "ANYCUBIC_TFT_MODEL is now ANYCUBIC_LCD_I3MEGA. Please update your Configuration.h." #endif #ifdef FIL_RUNOUT_INVERTING #if FIL_RUNOUT_INVERTING #warning "FIL_RUNOUT_INVERTING true is now FIL_RUNOUT_STATE HIGH. Please update Configuration.h." #else #warning "FIL_RUNOUT_INVERTING false is now FIL_RUNOUT_STATE LOW. Please update Configuration.h." #endif #ifndef FIL_RUNOUT_STATE #define FIL_RUNOUT_STATE ((FIL_RUNOUT_INVERTING) ? HIGH : LOW) #endif #endif /** * Probe temp compensation requirements */ #if ENABLED(PROBE_TEMP_COMPENSATION) #if defined(PTC_PARK_POS_X) || defined(PTC_PARK_POS_Y) || defined(PTC_PARK_POS_Z) #error "PTC_PARK_POS_[XYZ] is now PTC_PARK_POS (array). Please update Configuration_adv.h." #elif !defined(PTC_PARK_POS) #error "PROBE_TEMP_COMPENSATION requires PTC_PARK_POS." #elif defined(PTC_PROBE_POS_X) || defined(PTC_PROBE_POS_Y) #error "PTC_PROBE_POS_[XY] is now PTC_PROBE_POS (array). Please update Configuration_adv.h." #elif !defined(PTC_PROBE_POS) #error "PROBE_TEMP_COMPENSATION requires PTC_PROBE_POS." #endif #endif /** * Marlin release, version and default string */ #ifndef SHORT_BUILD_VERSION #error "SHORT_BUILD_VERSION must be specified." #elif !defined(DETAILED_BUILD_VERSION) #error "BUILD_VERSION must be specified." #elif !defined(STRING_DISTRIBUTION_DATE) #error "STRING_DISTRIBUTION_DATE must be specified." #elif !defined(PROTOCOL_VERSION) #error "PROTOCOL_VERSION must be specified." #elif !defined(MACHINE_NAME) #error "MACHINE_NAME must be specified." #elif !defined(SOURCE_CODE_URL) #error "SOURCE_CODE_URL must be specified." #elif !defined(DEFAULT_MACHINE_UUID) #error "DEFAULT_MACHINE_UUID must be specified." #elif !defined(WEBSITE_URL) #error "WEBSITE_URL must be specified." #endif /** * Serial */ #if !(defined(__AVR__) && defined(USBCON)) #if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024 #error "SERIAL_XON_XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops." #elif RX_BUFFER_SIZE && (RX_BUFFER_SIZE < 2 || !IS_POWER_OF_2(RX_BUFFER_SIZE)) #error "RX_BUFFER_SIZE must be a power of 2 greater than 1." #elif TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE)) #error "TX_BUFFER_SIZE must be 0 or a power of 2 between 1 and 256." #endif #elif ANY(SERIAL_XON_XOFF, SERIAL_STATS_MAX_RX_QUEUED, SERIAL_STATS_DROPPED_RX) #error "SERIAL_XON_XOFF and SERIAL_STATS_* features not supported on USB-native AVR devices." #endif #if SERIAL_PORT > 7 #error "Set SERIAL_PORT to the port on your board. Usually this is 0." #endif #if defined(SERIAL_PORT_2) && NUM_SERIAL < 2 #error "SERIAL_PORT_2 is not supported for your MOTHERBOARD. Disable it to continue." #endif /** * Multiple Stepper Drivers Per Axis */ #define GOOD_AXIS_PINS(A) (HAS_##A##_ENABLE && HAS_##A##_STEP && HAS_##A##_DIR) #if ENABLED(X_DUAL_STEPPER_DRIVERS) #if ENABLED(DUAL_X_CARRIAGE) #error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS." #elif !GOOD_AXIS_PINS(X) #error "X_DUAL_STEPPER_DRIVERS requires X2 pins to be defined." #endif #endif #if ENABLED(Y_DUAL_STEPPER_DRIVERS) && !GOOD_AXIS_PINS(Y) #error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins to be defined." #elif !WITHIN(NUM_Z_STEPPER_DRIVERS, 1, 4) #error "NUM_Z_STEPPER_DRIVERS must be an integer from 1 to 4." #elif NUM_Z_STEPPER_DRIVERS == 2 && !GOOD_AXIS_PINS(Z2) #error "If NUM_Z_STEPPER_DRIVERS is 2, you must define stepper pins for Z2." #elif NUM_Z_STEPPER_DRIVERS == 3 && !(GOOD_AXIS_PINS(Z2) && GOOD_AXIS_PINS(Z3)) #error "If NUM_Z_STEPPER_DRIVERS is 3, you must define stepper pins for Z2 and Z3." #elif NUM_Z_STEPPER_DRIVERS == 4 && !(GOOD_AXIS_PINS(Z2) && GOOD_AXIS_PINS(Z3) && GOOD_AXIS_PINS(Z4)) #error "If NUM_Z_STEPPER_DRIVERS is 4, you must define stepper pins for Z2, Z3, and Z4." #endif /** * Validate that the bed size fits */ static_assert(X_MAX_LENGTH >= X_BED_SIZE, "Movement bounds (X_MIN_POS, X_MAX_POS) are too narrow to contain X_BED_SIZE."); static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS) are too narrow to contain Y_BED_SIZE."); /** * Granular software endstops (Marlin >= 1.1.7) */ #if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z) #if IS_KINEMATIC #error "MIN_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MIN_SOFTWARE_ENDSTOP_Z." #elif NONE(MIN_SOFTWARE_ENDSTOP_X, MIN_SOFTWARE_ENDSTOP_Y) #error "MIN_SOFTWARE_ENDSTOPS requires at least one of the MIN_SOFTWARE_ENDSTOP_[XYZ] options." #endif #endif #if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z) #if IS_KINEMATIC #error "MAX_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MAX_SOFTWARE_ENDSTOP_Z." #elif NONE(MAX_SOFTWARE_ENDSTOP_X, MAX_SOFTWARE_ENDSTOP_Y) #error "MAX_SOFTWARE_ENDSTOPS requires at least one of the MAX_SOFTWARE_ENDSTOP_[XYZ] options." #endif #endif #if !defined(TARGET_LPC1768) && ANY( \ ENDSTOPPULLDOWNS, \ ENDSTOPPULLDOWN_XMAX, ENDSTOPPULLDOWN_YMAX, \ ENDSTOPPULLDOWN_ZMAX, ENDSTOPPULLDOWN_XMIN, \ ENDSTOPPULLDOWN_YMIN, ENDSTOPPULLDOWN_ZMIN \ ) #error "PULLDOWN pin mode is not available on the selected board." #endif #if BOTH(ENDSTOPPULLUPS, ENDSTOPPULLDOWNS) #error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS." #elif BOTH(FIL_RUNOUT_PULLUP, FIL_RUNOUT_PULLDOWN) #error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN." #elif BOTH(ENDSTOPPULLUP_XMAX, ENDSTOPPULLDOWN_XMAX) #error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX." #elif BOTH(ENDSTOPPULLUP_YMAX, ENDSTOPPULLDOWN_YMAX) #error "Enable only one of ENDSTOPPULLUP_Y_MAX or ENDSTOPPULLDOWN_Y_MAX." #elif BOTH(ENDSTOPPULLUP_ZMAX, ENDSTOPPULLDOWN_ZMAX) #error "Enable only one of ENDSTOPPULLUP_Z_MAX or ENDSTOPPULLDOWN_Z_MAX." #elif BOTH(ENDSTOPPULLUP_XMIN, ENDSTOPPULLDOWN_XMIN) #error "Enable only one of ENDSTOPPULLUP_X_MIN or ENDSTOPPULLDOWN_X_MIN." #elif BOTH(ENDSTOPPULLUP_YMIN, ENDSTOPPULLDOWN_YMIN) #error "Enable only one of ENDSTOPPULLUP_Y_MIN or ENDSTOPPULLDOWN_Y_MIN." #elif BOTH(ENDSTOPPULLUP_ZMIN, ENDSTOPPULLDOWN_ZMIN) #error "Enable only one of ENDSTOPPULLUP_Z_MIN or ENDSTOPPULLDOWN_Z_MIN." #endif /** * LCD Info Screen Style */ #if LCD_INFO_SCREEN_STYLE > 0 #if HAS_GRAPHICAL_LCD || LCD_WIDTH < 20 || LCD_HEIGHT < 4 #error "Alternative LCD_INFO_SCREEN_STYLE requires 20x4 Character LCD." #elif LCD_INFO_SCREEN_STYLE > 1 #error "LCD_INFO_SCREEN_STYLE only has options 0 and 1 at this time." #endif #endif /** * Progress Bar */ #if ENABLED(LCD_PROGRESS_BAR) #if NONE(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) #error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY." #elif !HAS_CHARACTER_LCD #error "LCD_PROGRESS_BAR requires a character LCD." #elif HAS_GRAPHICAL_LCD #error "LCD_PROGRESS_BAR does not apply to graphical displays." #elif ENABLED(FILAMENT_LCD_DISPLAY) #error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both." #elif PROGRESS_MSG_EXPIRE < 0 #error "PROGRESS_MSG_EXPIRE must be greater than or equal to 0." #endif #elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && NONE(HAS_GRAPHICAL_LCD, HAS_GRAPHICAL_TFT, EXTENSIBLE_UI) #error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR, Graphical LCD, TFT, or EXTENSIBLE_UI." #endif #if !HAS_LCD_MENU && ENABLED(SD_REPRINT_LAST_SELECTED_FILE) #error "SD_REPRINT_LAST_SELECTED_FILE currently requires a Marlin-native LCD menu." #endif /** * Custom Boot and Status screens */ #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) && NONE(HAS_GRAPHICAL_LCD, TOUCH_UI_FTDI_EVE) #error "SHOW_CUSTOM_BOOTSCREEN requires Graphical LCD or TOUCH_UI_FTDI_EVE." #elif ENABLED(CUSTOM_STATUS_SCREEN_IMAGE) && !HAS_GRAPHICAL_LCD #error "CUSTOM_STATUS_SCREEN_IMAGE requires a Graphical LCD." #endif /** * LCD Lightweight Screen Style */ #if ENABLED(LIGHTWEIGHT_UI) && DISABLED(U8GLIB_ST7920) #error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display." #endif /** * SD File Sorting */ #if ENABLED(SDCARD_SORT_ALPHA) #if SDSORT_LIMIT > 256 #error "SDSORT_LIMIT must be 256 or smaller." #elif SDSORT_LIMIT < 10 #error "SDSORT_LIMIT should be greater than 9 to be useful." #elif DISABLED(SDSORT_USES_RAM) #if ENABLED(SDSORT_DYNAMIC_RAM) #error "SDSORT_DYNAMIC_RAM requires SDSORT_USES_RAM (which reads the directory into RAM)." #elif ENABLED(SDSORT_CACHE_NAMES) #error "SDSORT_CACHE_NAMES requires SDSORT_USES_RAM (which reads the directory into RAM)." #endif #endif #if ENABLED(SDSORT_CACHE_NAMES) && DISABLED(SDSORT_DYNAMIC_RAM) #if SDSORT_CACHE_VFATS < 2 #error "SDSORT_CACHE_VFATS must be 2 or greater!" #elif SDSORT_CACHE_VFATS > MAX_VFAT_ENTRIES #undef SDSORT_CACHE_VFATS #define SDSORT_CACHE_VFATS MAX_VFAT_ENTRIES #warning "SDSORT_CACHE_VFATS was reduced to MAX_VFAT_ENTRIES!" #endif #endif #endif #if defined(EVENT_GCODE_SD_STOP) && DISABLED(NOZZLE_PARK_FEATURE) static_assert(nullptr == strstr(EVENT_GCODE_SD_STOP, "G27"), "NOZZLE_PARK_FEATURE is required to use G27 in EVENT_GCODE_SD_STOP."); #endif /** * I2C Position Encoders */ #if ENABLED(I2C_POSITION_ENCODERS) #if !BOTH(BABYSTEPPING, BABYSTEP_XY) #error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY." #elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5) #error "I2CPE_ENCODER_CNT must be between 1 and 5." #endif #endif /** * Babystepping */ #if ENABLED(BABYSTEPPING) #if ENABLED(SCARA) #error "BABYSTEPPING is not implemented for SCARA yet." #elif BOTH(DELTA, BABYSTEP_XY) #error "BABYSTEPPING only implemented for Z axis on deltabots." #elif BOTH(BABYSTEP_ZPROBE_OFFSET, MESH_BED_LEVELING) #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination" #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE #error "BABYSTEP_ZPROBE_OFFSET requires a probe." #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !HAS_GRAPHICAL_LCD #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD." #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET) #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET." #elif ENABLED(BABYSTEP_HOTEND_Z_OFFSET) && !HAS_HOTEND_OFFSET #error "BABYSTEP_HOTEND_Z_OFFSET requires 2 or more HOTENDS." #elif BOTH(BABYSTEP_ALWAYS_AVAILABLE, MOVE_Z_WHEN_IDLE) #error "BABYSTEP_ALWAYS_AVAILABLE and MOVE_Z_WHEN_IDLE are incompatible." #elif !defined(BABYSTEP_MULTIPLICATOR_Z) #error "BABYSTEPPING requires BABYSTEP_MULTIPLICATOR_Z." #elif ENABLED(BABYSTEP_XY) && !defined(BABYSTEP_MULTIPLICATOR_XY) #error "BABYSTEP_XY requires BABYSTEP_MULTIPLICATOR_XY." #elif ENABLED(BABYSTEP_MILLIMETER_UNITS) static_assert(BABYSTEP_MULTIPLICATOR_Z <= 0.1f, "BABYSTEP_MULTIPLICATOR_Z must be less or equal to 0.1mm."); #if ENABLED(BABYSTEP_XY) static_assert(BABYSTEP_MULTIPLICATOR_XY <= 0.25f, "BABYSTEP_MULTIPLICATOR_XY must be less than or equal to 0.25mm."); #endif #endif #endif /** * Filament Runout needs one or more pins and either SD Support or Auto print start detection */ #if HAS_FILAMENT_SENSOR #if !PIN_EXISTS(FIL_RUNOUT) #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN." #elif NUM_RUNOUT_SENSORS > E_STEPPERS #error "NUM_RUNOUT_SENSORS cannot exceed the number of E steppers." #elif NUM_RUNOUT_SENSORS > 1 && !PIN_EXISTS(FIL_RUNOUT2) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 1 requires FIL_RUNOUT2_PIN." #elif NUM_RUNOUT_SENSORS > 2 && !PIN_EXISTS(FIL_RUNOUT3) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 2 requires FIL_RUNOUT3_PIN." #elif NUM_RUNOUT_SENSORS > 3 && !PIN_EXISTS(FIL_RUNOUT4) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 3 requires FIL_RUNOUT4_PIN." #elif NUM_RUNOUT_SENSORS > 4 && !PIN_EXISTS(FIL_RUNOUT5) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 4 requires FIL_RUNOUT5_PIN." #elif NUM_RUNOUT_SENSORS > 5 && !PIN_EXISTS(FIL_RUNOUT6) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 5 requires FIL_RUNOUT6_PIN." #elif NONE(SDSUPPORT, PRINTJOB_TIMER_AUTOSTART) #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART." #elif FILAMENT_RUNOUT_DISTANCE_MM < 0 #error "FILAMENT_RUNOUT_DISTANCE_MM must be greater than or equal to zero." #elif DISABLED(ADVANCED_PAUSE_FEATURE) static_assert(nullptr == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR."); #endif #endif /** * Advanced Pause */ #if ENABLED(ADVANCED_PAUSE_FEATURE) #if !HAS_RESUME_CONTINUE #error "ADVANCED_PAUSE_FEATURE requires a supported LCD controller (or EMERGENCY_PARSER)." #elif DISABLED(NOZZLE_PARK_FEATURE) #error "ADVANCED_PAUSE_FEATURE requires NOZZLE_PARK_FEATURE." #elif !defined(FILAMENT_UNLOAD_PURGE_FEEDRATE) #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #elif ENABLED(EXTRUDER_RUNOUT_PREVENT) #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE." #elif ENABLED(PARK_HEAD_ON_PAUSE) && NONE(SDSUPPORT, NEWPANEL, EMERGENCY_PARSER) #error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller." #elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT) #error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT." #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_UNLOAD_LENGTH > EXTRUDE_MAXLENGTH #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_SLOW_LOAD_LENGTH > EXTRUDE_MAXLENGTH #error "FILAMENT_CHANGE_SLOW_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_FAST_LOAD_LENGTH > EXTRUDE_MAXLENGTH #error "FILAMENT_CHANGE_FAST_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." #endif #endif #if ENABLED(NOZZLE_PARK_FEATURE) constexpr float npp[] = NOZZLE_PARK_POINT; static_assert(COUNT(npp) == XYZ, "NOZZLE_PARK_POINT requires X, Y, and Z values."); constexpr xyz_pos_t npp_xyz = NOZZLE_PARK_POINT; static_assert(WITHIN(npp_xyz.x, X_MIN_POS, X_MAX_POS), "NOZZLE_PARK_POINT.X is out of bounds (X_MIN_POS, X_MAX_POS)."); static_assert(WITHIN(npp_xyz.y, Y_MIN_POS, Y_MAX_POS), "NOZZLE_PARK_POINT.Y is out of bounds (Y_MIN_POS, Y_MAX_POS)."); static_assert(WITHIN(npp_xyz.z, Z_MIN_POS, Z_MAX_POS), "NOZZLE_PARK_POINT.Z is out of bounds (Z_MIN_POS, Z_MAX_POS)."); #endif /** * Individual axis homing is useless for DELTAS */ #if BOTH(INDIVIDUAL_AXIS_HOMING_MENU, DELTA) #error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics." #endif /** * Options only for EXTRUDERS > 1 */ #if EXTRUDERS > 1 #if EXTRUDERS > 8 #error "Marlin supports a maximum of 8 EXTRUDERS." #endif #if ENABLED(HEATERS_PARALLEL) #error "EXTRUDERS must be 1 with HEATERS_PARALLEL." #endif #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) #ifndef TOOLCHANGE_FS_LENGTH #error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FS_LENGTH. Please update your Configuration_adv.h." #elif !defined(TOOLCHANGE_FS_RETRACT_SPEED) #error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FS_RETRACT_SPEED. Please update your Configuration_adv.h." #elif !defined(TOOLCHANGE_FS_PRIME_SPEED) #error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FS_PRIME_SPEED. Please update your Configuration_adv.h." #endif #endif #if ENABLED(TOOLCHANGE_PARK) #ifndef TOOLCHANGE_PARK_XY #error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY. Please update your Configuration." #elif !defined(TOOLCHANGE_PARK_XY_FEEDRATE) #error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY_FEEDRATE. Please update your Configuration." #endif #endif #ifndef TOOLCHANGE_ZRAISE #error "TOOLCHANGE_ZRAISE required for EXTRUDERS > 1. Please update your Configuration_adv.h." #endif #elif ENABLED(MK2_MULTIPLEXER) #error "MK2_MULTIPLEXER requires 2 or more EXTRUDERS." #elif ENABLED(SINGLENOZZLE) #error "SINGLENOZZLE requires 2 or more EXTRUDERS." #endif /** * Sanity checking for the Průša MK2 Multiplexer */ #ifdef SNMM #error "SNMM is now MK2_MULTIPLEXER. Please update your configuration." #endif /** * A Dual Nozzle carriage with switching servo */ #if ENABLED(SWITCHING_NOZZLE) #if ENABLED(DUAL_X_CARRIAGE) #error "SWITCHING_NOZZLE and DUAL_X_CARRIAGE are incompatible." #elif ENABLED(SINGLENOZZLE) #error "SWITCHING_NOZZLE and SINGLENOZZLE are incompatible." #elif EXTRUDERS != 2 #error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS." #elif NUM_SERVOS < 1 #error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1." #endif #ifndef SWITCHING_NOZZLE_SERVO_NR #error "SWITCHING_NOZZLE requires SWITCHING_NOZZLE_SERVO_NR." #elif SWITCHING_NOZZLE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) #error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE." #elif SWITCHING_NOZZLE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) #error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE." #elif SWITCHING_NOZZLE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) #error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE." #elif SWITCHING_NOZZLE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) #error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE." #endif #ifdef SWITCHING_NOZZLE_E1_SERVO_NR #if SWITCHING_NOZZLE_E1_SERVO_NR == SWITCHING_NOZZLE_SERVO_NR #error "SWITCHING_NOZZLE_E1_SERVO_NR must be different from SWITCHING_NOZZLE_SERVO_NR." #elif SWITCHING_NOZZLE_E1_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) #error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE." #elif SWITCHING_NOZZLE_E1_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) #error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE." #elif SWITCHING_NOZZLE_E1_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) #error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE." #elif SWITCHING_NOZZLE_E1_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) #error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE." #endif #endif #endif /** * Single Stepper Dual Extruder with switching servo */ #if ENABLED(SWITCHING_EXTRUDER) #if NUM_SERVOS < 1 #error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1." #elif SWITCHING_EXTRUDER_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) #error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) #error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) #error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) #error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER." #endif #if EXTRUDERS > 3 #if NUM_SERVOS < 2 #error "SWITCHING_EXTRUDER with 4 extruders requires NUM_SERVOS >= 2." #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) #error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) #error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) #error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_E23_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) #error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER." #elif SWITCHING_EXTRUDER_E23_SERVO_NR == SWITCHING_EXTRUDER_SERVO_NR #error "SWITCHING_EXTRUDER_E23_SERVO_NR should be a different extruder from SWITCHING_EXTRUDER_SERVO_NR." #endif #endif #endif /** * Mixing Extruder requirements */ #if ENABLED(MIXING_EXTRUDER) #if EXTRUDERS > 1 #error "For MIXING_EXTRUDER set MIXING_STEPPERS > 1 instead of EXTRUDERS > 1." #elif MIXING_STEPPERS < 2 #error "You must set MIXING_STEPPERS >= 2 for a mixing extruder." #elif ENABLED(FILAMENT_SENSOR) #error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway." #elif ENABLED(SWITCHING_EXTRUDER) #error "Please select either MIXING_EXTRUDER or SWITCHING_EXTRUDER, not both." #elif ENABLED(SINGLENOZZLE) #error "MIXING_EXTRUDER is incompatible with SINGLENOZZLE." #endif #endif /** * Linear Advance 1.5 - Check K value range */ #if ENABLED(LIN_ADVANCE) static_assert( WITHIN(LIN_ADVANCE_K, 0, 10), "LIN_ADVANCE_K must be a value from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)." ); #if ENABLED(S_CURVE_ACCELERATION) && DISABLED(EXPERIMENTAL_SCURVE) #error "LIN_ADVANCE and S_CURVE_ACCELERATION may not play well together! Enable EXPERIMENTAL_SCURVE to continue." #endif #endif /** * Special tool-changing options */ #if 1 < 0 \ + ENABLED(SINGLENOZZLE) \ + ENABLED(DUAL_X_CARRIAGE) \ + ENABLED(PARKING_EXTRUDER) \ + ENABLED(MAGNETIC_PARKING_EXTRUDER) \ + ENABLED(SWITCHING_TOOLHEAD) \ + ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) \ + ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #error "Please select only one of SINGLENOZZLE, DUAL_X_CARRIAGE, PARKING_EXTRUDER, SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, or ELECTROMAGNETIC_SWITCHING_TOOLHEAD." #endif /** * (Magnetic) Parking Extruder requirements */ #if ANY(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) #if ENABLED(EXT_SOLENOID) #error "(MAGNETIC_)PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)" #elif EXTRUDERS != 2 #error "(MAGNETIC_)PARKING_EXTRUDER requires exactly 2 EXTRUDERS." #elif !defined(PARKING_EXTRUDER_PARKING_X) #error "(MAGNETIC_)PARKING_EXTRUDER requires PARKING_EXTRUDER_PARKING_X." #elif !defined(TOOLCHANGE_ZRAISE) #error "(MAGNETIC_)PARKING_EXTRUDER requires TOOLCHANGE_ZRAISE." #elif TOOLCHANGE_ZRAISE < 0 #error "TOOLCHANGE_ZRAISE must be 0 or higher." #elif ENABLED(PARKING_EXTRUDER) #if !PINS_EXIST(SOL0, SOL1) #error "PARKING_EXTRUDER requires SOL0_PIN and SOL1_PIN." #elif !defined(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE, LOW, HIGH) #error "PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE must be defined as HIGH or LOW." #elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000) #error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)." #endif #endif #endif /** * Switching Toolhead requirements */ #if ENABLED(SWITCHING_TOOLHEAD) #ifndef SWITCHING_TOOLHEAD_SERVO_NR #error "SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_SERVO_NR." #elif EXTRUDERS < 2 #error "SWITCHING_TOOLHEAD requires at least 2 EXTRUDERS." #elif NUM_SERVOS < (SWITCHING_TOOLHEAD_SERVO_NR - 1) #if SWITCHING_TOOLHEAD_SERVO_NR == 0 #error "A SWITCHING_TOOLHEAD_SERVO_NR of 0 requires NUM_SERVOS >= 1." #elif SWITCHING_TOOLHEAD_SERVO_NR == 1 #error "A SWITCHING_TOOLHEAD_SERVO_NR of 1 requires NUM_SERVOS >= 2." #elif SWITCHING_TOOLHEAD_SERVO_NR == 2 #error "A SWITCHING_TOOLHEAD_SERVO_NR of 2 requires NUM_SERVOS >= 3." #elif SWITCHING_TOOLHEAD_SERVO_NR == 3 #error "A SWITCHING_TOOLHEAD_SERVO_NR of 3 requires NUM_SERVOS >= 4." #endif #elif !defined(TOOLCHANGE_ZRAISE) #error "SWITCHING_TOOLHEAD requires TOOLCHANGE_ZRAISE." #elif TOOLCHANGE_ZRAISE < 0 #error "TOOLCHANGE_ZRAISE must be 0 or higher." #endif #endif /** * (Electro)magnetic Switching Toolhead requirements */ #if EITHER(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #ifndef SWITCHING_TOOLHEAD_Y_POS #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_POS" #elif !defined(SWITCHING_TOOLHEAD_X_POS) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_X_POS" #elif !defined(SWITCHING_TOOLHEAD_Z_HOP) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Z_HOP." #elif !defined(SWITCHING_TOOLHEAD_Y_CLEAR) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_CLEAR." #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #if ENABLED(EXT_SOLENOID) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD and EXT_SOLENOID are incompatible. (Pins are used twice.)" #elif !PIN_EXISTS(SOL0) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SOL0_PIN." #endif #endif #endif /** * Part-Cooling Fan Multiplexer requirements */ #if PIN_EXISTS(FANMUX1) #if !HAS_FANMUX #error "FANMUX0_PIN must be set before FANMUX1_PIN can be set." #endif #elif PIN_EXISTS(FANMUX2) #error "FANMUX0_PIN and FANMUX1_PIN must be set before FANMUX2_PIN can be set." #endif /** * Limited number of servos */ #if NUM_SERVOS > NUM_SERVO_PLUGS #error "The selected board doesn't support enough servos for your configuration. Reduce NUM_SERVOS." #endif /** * Servo deactivation depends on servo endstops, switching nozzle, or switching extruder */ #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_PROBE && !defined(SWITCHING_NOZZLE_SERVO_NR) && !defined(SWITCHING_EXTRUDER_SERVO_NR) && !defined(SWITCHING_TOOLHEAD_SERVO_NR) #error "Z_PROBE_SERVO_NR, switching nozzle, switching toolhead or switching extruder is required for DEACTIVATE_SERVOS_AFTER_MOVE." #endif /** * Required LCD language */ #if HAS_CHARACTER_LCD && !defined(DISPLAY_CHARSET_HD44780) #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller." #endif /** * Bed Heating Options - PID vs Limit Switching */ #if BOTH(PIDTEMPBED, BED_LIMIT_SWITCHING) #error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED." #endif /** * Kinematics */ /** * Allow only one kinematic type to be defined */ #if 1 < 0 \ + ENABLED(DELTA) \ + ENABLED(MORGAN_SCARA) \ + ENABLED(COREXY) \ + ENABLED(COREXZ) \ + ENABLED(COREYZ) \ + ENABLED(COREYX) \ + ENABLED(COREZX) \ + ENABLED(COREZY) #error "Please enable only one of DELTA, MORGAN_SCARA, COREXY, COREYX, COREXZ, COREZX, COREYZ, or COREZY." #endif /** * Delta requirements */ #if ENABLED(DELTA) #if NONE(USE_XMAX_PLUG, USE_YMAX_PLUG, USE_ZMAX_PLUG) #error "You probably want to use Max Endstops for DELTA!" #elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_SEGMENTED #error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." #elif ENABLED(DELTA_AUTO_CALIBRATION) && !(HAS_BED_PROBE || HAS_LCD_MENU) #error "DELTA_AUTO_CALIBRATION requires a probe or LCD Controller." #elif ENABLED(DELTA_CALIBRATION_MENU) && !HAS_LCD_MENU #error "DELTA_CALIBRATION_MENU requires an LCD Controller." #elif ABL_GRID #if (GRID_MAX_POINTS_X & 1) == 0 || (GRID_MAX_POINTS_Y & 1) == 0 #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be odd numbers." #elif GRID_MAX_POINTS_X < 3 #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be 3 or higher." #endif #endif #endif /** * Junction deviation is incompatible with kinematic systems. */ #if HAS_JUNCTION_DEVIATION && IS_KINEMATIC #error "CLASSIC_JERK is required for DELTA and SCARA." #endif /** * Probes */ /** * Allow only one probe option to be defined */ #if 1 < 0 \ + ENABLED(PROBE_MANUALLY) \ + ENABLED(FIX_MOUNTED_PROBE) \ + ENABLED(NOZZLE_AS_PROBE) \ + (HAS_Z_SERVO_PROBE && DISABLED(BLTOUCH)) \ + ENABLED(BLTOUCH) && DISABLED(CREALITY_TOUCH) \ + ENABLED(CREALITY_TOUCH) \ + ENABLED(TOUCH_MI_PROBE) \ + ENABLED(SOLENOID_PROBE) \ + ENABLED(Z_PROBE_ALLEN_KEY) \ + ENABLED(Z_PROBE_SLED) \ + ENABLED(RACK_AND_PINION_PROBE) \ + ENABLED(SENSORLESS_PROBING) #error "Please enable only one probe option: PROBE_MANUALLY, SENSORLESS_PROBING, BLTOUCH, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo." #endif #if HAS_BED_PROBE /** * Z_PROBE_SLED is incompatible with DELTA */ #if BOTH(Z_PROBE_SLED, DELTA) #error "You cannot use Z_PROBE_SLED with DELTA." #endif /** * SOLENOID_PROBE requirements */ #if ENABLED(SOLENOID_PROBE) #if ENABLED(EXT_SOLENOID) #error "SOLENOID_PROBE is incompatible with EXT_SOLENOID." #elif !HAS_SOLENOID_1 #error "SOLENOID_PROBE requires SOL1_PIN. It can be added to your Configuration.h." #endif #endif /** * NUM_SERVOS is required for a Z servo probe */ #if HAS_Z_SERVO_PROBE #ifndef NUM_SERVOS #error "You must set NUM_SERVOS for a Z servo probe (Z_PROBE_SERVO_NR)." #elif Z_PROBE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0) #error "SERVO0_PIN must be defined for your servo or BLTOUCH probe." #elif Z_PROBE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1) #error "SERVO1_PIN must be defined for your servo or BLTOUCH probe." #elif Z_PROBE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2) #error "SERVO2_PIN must be defined for your servo or BLTOUCH probe." #elif Z_PROBE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3) #error "SERVO3_PIN must be defined for your servo or BLTOUCH probe." #elif Z_PROBE_SERVO_NR >= NUM_SERVOS #error "Z_PROBE_SERVO_NR must be smaller than NUM_SERVOS." #endif #endif #if ENABLED(BLTOUCH) #if BLTOUCH_DELAY < 200 #error "BLTOUCH_DELAY less than 200 is unsafe and is not supported." #elif DISABLED(BLTOUCH_SET_5V_MODE) && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_ZMIN, ENDSTOPPULLUP_ZMIN_PROBE) #error "BLTOUCH without BLTOUCH_SET_5V_MODE requires ENDSTOPPULLUPS, ENDSTOPPULLUP_ZMIN or ENDSTOPPULLUP_ZMIN_PROBE." #endif #endif #if ENABLED(RACK_AND_PINION_PROBE) && !(defined(Z_PROBE_DEPLOY_X) && defined(Z_PROBE_RETRACT_X)) #error "RACK_AND_PINION_PROBE requires Z_PROBE_DEPLOY_X and Z_PROBE_RETRACT_X." #endif /** * Touch-MI probe requirements */ #if ENABLED(TOUCH_MI_PROBE) #if DISABLED(Z_SAFE_HOMING) #error "TOUCH_MI_PROBE requires Z_SAFE_HOMING." #elif !defined(TOUCH_MI_RETRACT_Z) #error "TOUCH_MI_PROBE requires TOUCH_MI_RETRACT_Z." #elif defined(Z_AFTER_PROBING) #error "TOUCH_MI_PROBE requires Z_AFTER_PROBING to be disabled." #elif Z_HOMING_HEIGHT < 10 #error "TOUCH_MI_PROBE requires Z_HOMING_HEIGHT >= 10." #elif Z_MIN_PROBE_ENDSTOP_INVERTING #error "TOUCH_MI_PROBE requires Z_MIN_PROBE_ENDSTOP_INVERTING to be set to false." #elif DISABLED(BABYSTEP_ZPROBE_OFFSET) #error "TOUCH_MI_PROBE requires BABYSTEPPING with BABYSTEP_ZPROBE_OFFSET." #elif !HAS_RESUME_CONTINUE #error "TOUCH_MI_PROBE currently requires an LCD controller or EMERGENCY_PARSER." #endif #endif /** * Require pin options and pins to be defined */ #if ENABLED(SENSORLESS_PROBING) #if ENABLED(DELTA) && !(AXIS_HAS_STALLGUARD(X) && AXIS_HAS_STALLGUARD(Y) && AXIS_HAS_STALLGUARD(Z)) #error "SENSORLESS_PROBING requires TMC2130/2160/2209/5130/5160 drivers on X, Y, and Z." #elif !AXIS_HAS_STALLGUARD(Z) #error "SENSORLESS_PROBING requires a TMC2130/2160/2209/5130/5160 driver on Z." #endif #elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) #if DISABLED(USE_ZMIN_PLUG) #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled." #elif !HAS_Z_MIN #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined." #elif Z_MIN_PROBE_ENDSTOP_INVERTING != Z_MIN_ENDSTOP_INVERTING #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING." #endif #elif !HAS_Z_MIN_PROBE_PIN #error "Z_MIN_PROBE_PIN must be defined if Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN is not enabled." #endif #if ENABLED(NOZZLE_AS_PROBE) constexpr float sanity_nozzle_to_probe_offset[] = NOZZLE_TO_PROBE_OFFSET; static_assert(sanity_nozzle_to_probe_offset[0] == 0.0 && sanity_nozzle_to_probe_offset[1] == 0.0, "NOZZLE_AS_PROBE requires the X,Y offsets in NOZZLE_TO_PROBE_OFFSET to be 0,0."); #endif #if DISABLED(NOZZLE_AS_PROBE) static_assert(PROBING_MARGIN >= 0, "PROBING_MARGIN must be >= 0."); static_assert(PROBING_MARGIN_BACK >= 0, "PROBING_MARGIN_BACK must be >= 0."); static_assert(PROBING_MARGIN_FRONT >= 0, "PROBING_MARGIN_FRONT must be >= 0."); static_assert(PROBING_MARGIN_LEFT >= 0, "PROBING_MARGIN_LEFT must be >= 0."); static_assert(PROBING_MARGIN_RIGHT >= 0, "PROBING_MARGIN_RIGHT must be >= 0."); #endif #define _MARGIN(A) TERN(IS_SCARA, SCARA_PRINTABLE_RADIUS, TERN(DELTA, DELTA_PRINTABLE_RADIUS, A##_CENTER)) static_assert(PROBING_MARGIN < _MARGIN(X), "PROBING_MARGIN is too large."); static_assert(PROBING_MARGIN_BACK < _MARGIN(Y), "PROBING_MARGIN_BACK is too large."); static_assert(PROBING_MARGIN_FRONT < _MARGIN(Y), "PROBING_MARGIN_FRONT is too large."); static_assert(PROBING_MARGIN_LEFT < _MARGIN(X), "PROBING_MARGIN_LEFT is too large."); static_assert(PROBING_MARGIN_RIGHT < _MARGIN(X), "PROBING_MARGIN_RIGHT is too large."); #undef _MARGIN /** * Make sure Z raise values are set */ #ifndef Z_CLEARANCE_DEPLOY_PROBE #error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration." #elif !defined(Z_CLEARANCE_BETWEEN_PROBES) #error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration." #elif Z_CLEARANCE_DEPLOY_PROBE < 0 #error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0." #elif Z_CLEARANCE_BETWEEN_PROBES < 0 #error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0." #elif Z_AFTER_PROBING < 0 #error "Probes need Z_AFTER_PROBING >= 0." #endif #if MULTIPLE_PROBING > 0 || EXTRA_PROBING > 0 #if MULTIPLE_PROBING == 0 #error "EXTRA_PROBING requires MULTIPLE_PROBING." #elif MULTIPLE_PROBING < 2 #error "MULTIPLE_PROBING must be 2 or more." #elif MULTIPLE_PROBING <= EXTRA_PROBING #error "EXTRA_PROBING must be less than MULTIPLE_PROBING." #endif #endif #if Z_PROBE_LOW_POINT > 0 #error "Z_PROBE_LOW_POINT must be less than or equal to 0." #endif #if HOMING_Z_WITH_PROBE && IS_CARTESIAN && DISABLED(Z_SAFE_HOMING) #error "Z_SAFE_HOMING is recommended when homing with a probe. Enable it or comment out this line to continue." #endif #else /** * Require some kind of probe for bed leveling and probe testing */ #if HAS_ABL_NOT_UBL && !PROBE_SELECTED #error "Auto Bed Leveling requires one of these: PROBE_MANUALLY, SENSORLESS_PROBING, BLTOUCH, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or a Z Servo." #endif #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST) #error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe: FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo." #endif #endif /** * Allow only one bed leveling option to be defined */ #if 1 < 0 \ + ENABLED(AUTO_BED_LEVELING_LINEAR) \ + ENABLED(AUTO_BED_LEVELING_3POINT) \ + ENABLED(AUTO_BED_LEVELING_BILINEAR) \ + ENABLED(AUTO_BED_LEVELING_UBL) \ + ENABLED(MESH_BED_LEVELING) #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." #endif /** * Bed Leveling Requirements */ #if ENABLED(AUTO_BED_LEVELING_UBL) /** * Unified Bed Leveling */ // Hide PROBE_MANUALLY from the rest of the code #undef PROBE_MANUALLY #if IS_SCARA #error "AUTO_BED_LEVELING_UBL does not yet support SCARA printers." #elif DISABLED(EEPROM_SETTINGS) #error "AUTO_BED_LEVELING_UBL requires EEPROM_SETTINGS. Please update your configuration." #elif !WITHIN(GRID_MAX_POINTS_X, 3, 15) || !WITHIN(GRID_MAX_POINTS_Y, 3, 15) #error "GRID_MAX_POINTS_[XY] must be a whole number between 3 and 15." #elif !defined(RESTORE_LEVELING_AFTER_G28) #error "AUTO_BED_LEVELING_UBL used to enable RESTORE_LEVELING_AFTER_G28. To keep this behavior enable RESTORE_LEVELING_AFTER_G28. Otherwise define it as 'false'." #endif #elif HAS_ABL_NOT_UBL /** * Auto Bed Leveling */ /** * Delta and SCARA have limited bed leveling options */ #if IS_SCARA && DISABLED(AUTO_BED_LEVELING_BILINEAR) #error "SCARA machines can only use the AUTO_BED_LEVELING_BILINEAR leveling option." #endif #elif ENABLED(MESH_BED_LEVELING) // Hide PROBE_MANUALLY from the rest of the code #undef PROBE_MANUALLY /** * Mesh Bed Leveling */ #if ENABLED(DELTA) #error "MESH_BED_LEVELING is not compatible with DELTA printers." #elif GRID_MAX_POINTS_X > 9 || GRID_MAX_POINTS_Y > 9 #error "GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y must be less than 10 for MBL." #endif #endif #if HAS_MESH && HAS_CLASSIC_JERK static_assert(DEFAULT_ZJERK > 0.1, "Low DEFAULT_ZJERK values are incompatible with mesh-based leveling."); #endif #if ENABLED(G26_MESH_VALIDATION) #if !EXTRUDERS #error "G26_MESH_VALIDATION requires at least one extruder." #elif !HAS_MESH #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL." #endif #endif #if ENABLED(MESH_EDIT_GFX_OVERLAY) && !BOTH(AUTO_BED_LEVELING_UBL, HAS_GRAPHICAL_LCD) #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD." #endif #if ENABLED(G29_RETRY_AND_RECOVER) #if ENABLED(AUTO_BED_LEVELING_UBL) #error "G29_RETRY_AND_RECOVER is not compatible with UBL." #elif ENABLED(MESH_BED_LEVELING) #error "G29_RETRY_AND_RECOVER is not compatible with MESH_BED_LEVELING." #endif #endif /** * LCD_BED_LEVELING requirements */ #if ENABLED(LCD_BED_LEVELING) #if !HAS_LCD_MENU #error "LCD_BED_LEVELING requires a programmable LCD controller." #elif !(ENABLED(MESH_BED_LEVELING) || HAS_ABL_NOT_UBL) #error "LCD_BED_LEVELING requires MESH_BED_LEVELING or AUTO_BED_LEVELING." #endif #endif /** * Homing */ constexpr float hbm[] = HOMING_BUMP_MM; static_assert(COUNT(hbm) == XYZ, "HOMING_BUMP_MM requires X, Y, and Z elements."); static_assert(hbm[X_AXIS] >= 0, "HOMING_BUMP_MM.X must be greater than or equal to 0."); static_assert(hbm[Y_AXIS] >= 0, "HOMING_BUMP_MM.Y must be greater than or equal to 0."); static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal to 0."); #if ENABLED(CODEPENDENT_XY_HOMING) #if ENABLED(QUICK_HOME) #error "QUICK_HOME is incompatible with CODEPENDENT_XY_HOMING." #elif IS_KINEMATIC #error "CODEPENDENT_XY_HOMING requires a Cartesian setup." #endif #endif /** * Make sure Z_SAFE_HOMING point is reachable */ #if ENABLED(Z_SAFE_HOMING) static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, X_MIN_POS, X_MAX_POS), "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle."); static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, Y_MIN_POS, Y_MAX_POS), "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle."); #endif /** * Make sure DISABLE_[XYZ] compatible with selected homing options */ #if ANY(DISABLE_X, DISABLE_Y, DISABLE_Z) #if EITHER(HOME_AFTER_DEACTIVATE, Z_SAFE_HOMING) #error "DISABLE_[XYZ] is not compatible with HOME_AFTER_DEACTIVATE or Z_SAFE_HOMING." #endif #endif /** * Filament Width Sensor */ #if ENABLED(FILAMENT_WIDTH_SENSOR) #if !HAS_FILAMENT_WIDTH_SENSOR #error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined." #elif ENABLED(NO_VOLUMETRICS) #error "FILAMENT_WIDTH_SENSOR requires NO_VOLUMETRICS to be disabled." #endif #endif /** * System Power Sensor */ #if ENABLED(POWER_MONITOR_CURRENT) && !PIN_EXISTS(POWER_MONITOR_CURRENT) #error "POWER_MONITOR_CURRENT requires a valid POWER_MONITOR_CURRENT_PIN." #elif ENABLED(POWER_MONITOR_VOLTAGE) && !PIN_EXISTS(POWER_MONITOR_VOLTAGE) #error "POWER_MONITOR_VOLTAGE requires POWER_MONITOR_VOLTAGE_PIN to be defined." #elif BOTH(POWER_MONITOR_CURRENT, POWER_MONITOR_VOLTAGE) && POWER_MONITOR_CURRENT_PIN == POWER_MONITOR_VOLTAGE_PIN #error "POWER_MONITOR_CURRENT_PIN and POWER_MONITOR_VOLTAGE_PIN must be different." #endif /** * Volumetric Extruder Limit */ #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT) #if ENABLED(NO_VOLUMETRICS) #error "VOLUMETRIC_EXTRUDER_LIMIT requires NO_VOLUMETRICS to be disabled." #elif MIN_STEPS_PER_SEGMENT > 1 #error "VOLUMETRIC_EXTRUDER_LIMIT is not compatible with MIN_STEPS_PER_SEGMENT greater than 1." #endif #endif /** * ULTIPANEL encoder */ #if ENABLED(ULTIPANEL) && NONE(NEWPANEL, SR_LCD_2W_NL) && !defined(SHIFT_CLK) #error "ULTIPANEL requires some kind of encoder." #endif #if ENCODER_PULSES_PER_STEP < 0 #error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead." #endif /** * SAV_3DGLCD display options */ #if ENABLED(SAV_3DGLCD) #if NONE(U8GLIB_SSD1306, U8GLIB_SH1106) #error "Enable a SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." #elif BOTH(U8GLIB_SSD1306, U8GLIB_SH1106) #error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." #endif #endif /** * Allen Key * Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis. */ #if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) #error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY." #endif /** * Dual X Carriage requirements */ #if ENABLED(DUAL_X_CARRIAGE) #if EXTRUDERS < 2 #error "DUAL_X_CARRIAGE requires 2 (or more) extruders." #elif CORE_IS_XY || CORE_IS_XZ #error "DUAL_X_CARRIAGE cannot be used with COREXY, COREYX, COREXZ, or COREZX." #elif !GOOD_AXIS_PINS(X2) #error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined." #elif !HAS_X_MAX #error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop." #elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS) #error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS." #elif X_HOME_DIR != -1 || X2_HOME_DIR != 1 #error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1." #endif #endif #undef GOOD_AXIS_PINS /** * Make sure auto fan pins don't conflict with the fan pin */ #if HAS_AUTO_FAN #if HAS_FAN0 #if E0_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN." #elif E1_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E1_AUTO_FAN_PIN equal to FAN_PIN." #elif E2_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E2_AUTO_FAN_PIN equal to FAN_PIN." #elif E3_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E3_AUTO_FAN_PIN equal to FAN_PIN." #endif #endif #endif #if HAS_FAN0 && CONTROLLER_FAN_PIN == FAN_PIN #error "You cannot set CONTROLLER_FAN_PIN equal to FAN_PIN." #endif #if ENABLED(USE_CONTROLLER_FAN) #if !HAS_CONTROLLER_FAN #error "USE_CONTROLLER_FAN requires a CONTROLLER_FAN_PIN. Define in Configuration_adv.h." #elif E0_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E0_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #elif E1_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E1_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #elif E2_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E2_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #elif E3_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E3_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #endif #endif /** * Case Light requirements */ #if ENABLED(CASE_LIGHT_ENABLE) #if !PIN_EXISTS(CASE_LIGHT) #error "CASE_LIGHT_ENABLE requires CASE_LIGHT_PIN to be defined." #elif CASE_LIGHT_PIN == FAN_PIN #error "CASE_LIGHT_PIN conflicts with FAN_PIN. Resolve before continuing." #endif #endif /** * Required custom thermistor settings */ #if ENABLED(HEATER_0_USER_THERMISTOR) && !(defined(HOTEND0_PULLUP_RESISTOR_OHMS) && defined(HOTEND0_RESISTANCE_25C_OHMS) && defined(HOTEND0_BETA)) #error "TEMP_SENSOR_0 1000 requires HOTEND0_PULLUP_RESISTOR_OHMS, HOTEND0_RESISTANCE_25C_OHMS and HOTEND0_BETA in Configuration_adv.h." #elif ENABLED(HEATER_1_USER_THERMISTOR) && !(defined(HOTEND1_PULLUP_RESISTOR_OHMS) && defined(HOTEND1_RESISTANCE_25C_OHMS) && defined(HOTEND1_BETA)) #error "TEMP_SENSOR_1 1000 requires HOTEND1_PULLUP_RESISTOR_OHMS, HOTEND1_RESISTANCE_25C_OHMS and HOTEND1_BETA in Configuration_adv.h." #elif ENABLED(HEATER_2_USER_THERMISTOR) && !(defined(HOTEND2_PULLUP_RESISTOR_OHMS) && defined(HOTEND2_RESISTANCE_25C_OHMS) && defined(HOTEND2_BETA)) #error "TEMP_SENSOR_2 1000 requires HOTEND2_PULLUP_RESISTOR_OHMS, HOTEND2_RESISTANCE_25C_OHMS and HOTEND2_BETA in Configuration_adv.h." #elif ENABLED(HEATER_3_USER_THERMISTOR) && !(defined(HOTEND3_PULLUP_RESISTOR_OHMS) && defined(HOTEND3_RESISTANCE_25C_OHMS) && defined(HOTEND3_BETA)) #error "TEMP_SENSOR_3 1000 requires HOTEND3_PULLUP_RESISTOR_OHMS, HOTEND3_RESISTANCE_25C_OHMS and HOTEND3_BETA in Configuration_adv.h." #elif ENABLED(HEATER_4_USER_THERMISTOR) && !(defined(HOTEND4_PULLUP_RESISTOR_OHMS) && defined(HOTEND4_RESISTANCE_25C_OHMS) && defined(HOTEND4_BETA)) #error "TEMP_SENSOR_4 1000 requires HOTEND4_PULLUP_RESISTOR_OHMS, HOTEND4_RESISTANCE_25C_OHMS and HOTEND4_BETA in Configuration_adv.h." #elif ENABLED(HEATER_5_USER_THERMISTOR) && !(defined(HOTEND5_PULLUP_RESISTOR_OHMS) && defined(HOTEND5_RESISTANCE_25C_OHMS) && defined(HOTEND5_BETA)) #error "TEMP_SENSOR_5 1000 requires HOTEND5_PULLUP_RESISTOR_OHMS, HOTEND5_RESISTANCE_25C_OHMS and HOTEND5_BETA in Configuration_adv.h." #elif ENABLED(HEATER_6_USER_THERMISTOR) && !(defined(HOTEND6_PULLUP_RESISTOR_OHMS) && defined(HOTEND6_RESISTANCE_25C_OHMS) && defined(HOTEND6_BETA)) #error "TEMP_SENSOR_6 1000 requires HOTEND6_PULLUP_RESISTOR_OHMS, HOTEND6_RESISTANCE_25C_OHMS and HOTEND6_BETA in Configuration_adv.h." #elif ENABLED(HEATER_7_USER_THERMISTOR) && !(defined(HOTEND7_PULLUP_RESISTOR_OHMS) && defined(HOTEND7_RESISTANCE_25C_OHMS) && defined(HOTEND7_BETA)) #error "TEMP_SENSOR_7 1000 requires HOTEND7_PULLUP_RESISTOR_OHMS, HOTEND7_RESISTANCE_25C_OHMS and HOTEND7_BETA in Configuration_adv.h." #elif ENABLED(HEATER_BED_USER_THERMISTOR) && !(defined(BED_PULLUP_RESISTOR_OHMS) && defined(BED_RESISTANCE_25C_OHMS) && defined(BED_BETA)) #error "TEMP_SENSOR_BED 1000 requires BED_PULLUP_RESISTOR_OHMS, BED_RESISTANCE_25C_OHMS and BED_BETA in Configuration_adv.h." #elif ENABLED(HEATER_CHAMBER_USER_THERMISTOR) && !(defined(CHAMBER_PULLUP_RESISTOR_OHMS) && defined(CHAMBER_RESISTANCE_25C_OHMS) && defined(CHAMBER_BETA)) #error "TEMP_SENSOR_CHAMBER 1000 requires CHAMBER_PULLUP_RESISTOR_OHMS, CHAMBER_RESISTANCE_25C_OHMS and CHAMBER_BETA in Configuration_adv.h." #endif /** * A Sensor ID has to be set for each heater */ #if HAS_MULTI_HOTEND #if ENABLED(HEATER_1_USES_MAX6675) && !PIN_EXISTS(MAX6675_SS2) #error "MAX6675_SS2_PIN (required for TEMP_SENSOR_1) not defined for this board." #elif TEMP_SENSOR_1 == 0 #error "TEMP_SENSOR_1 is required with 2 or more HOTENDS." #elif !ANY_PIN(TEMP_1, MAX6675_SS2) #error "TEMP_1_PIN not defined for this board." #elif ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) #error "HOTENDS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT." #endif #if HOTENDS > 2 #if TEMP_SENSOR_2 == 0 #error "TEMP_SENSOR_2 is required with 3 or more HOTENDS." #elif !HAS_HEATER_2 #error "HEATER_2_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_2) #error "TEMP_2_PIN not defined for this board." #endif #if HOTENDS > 3 #if TEMP_SENSOR_3 == 0 #error "TEMP_SENSOR_3 is required with 4 or more HOTENDS." #elif !HAS_HEATER_3 #error "HEATER_3_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_3) #error "TEMP_3_PIN not defined for this board." #endif #if HOTENDS > 4 #if TEMP_SENSOR_4 == 0 #error "TEMP_SENSOR_4 is required with 5 or more HOTENDS." #elif !HAS_HEATER_4 #error "HEATER_4_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_4) #error "TEMP_4_PIN not defined for this board." #endif #if HOTENDS > 5 #if TEMP_SENSOR_5 == 0 #error "TEMP_SENSOR_5 is required with 6 HOTENDS." #elif !HAS_HEATER_5 #error "HEATER_5_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_5) #error "TEMP_5_PIN not defined for this board." #endif #if HOTENDS > 6 #if TEMP_SENSOR_6 == 0 #error "TEMP_SENSOR_6 is required with 6 HOTENDS." #elif !HAS_HEATER_6 #error "HEATER_6_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_6) #error "TEMP_6_PIN not defined for this board." #endif #if HOTENDS > 7 #if TEMP_SENSOR_7 == 0 #error "TEMP_SENSOR_7 is required with 7 HOTENDS." #elif !HAS_HEATER_7 #error "HEATER_7_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_7) #error "TEMP_7_PIN not defined for this board." #endif #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 7 HOTENDS." #endif #elif TEMP_SENSOR_6 != 0 #error "TEMP_SENSOR_6 shouldn't be set with only 6 HOTENDS." #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 6 HOTENDS." #endif #elif TEMP_SENSOR_5 != 0 #error "TEMP_SENSOR_5 shouldn't be set with only 5 HOTENDS." #elif TEMP_SENSOR_6 != 0 #error "TEMP_SENSOR_6 shouldn't be set with only 5 HOTENDS." #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 5 HOTENDS." #endif #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS." #elif TEMP_SENSOR_5 != 0 #error "TEMP_SENSOR_5 shouldn't be set with only 4 HOTENDS." #elif TEMP_SENSOR_6 != 0 #error "TEMP_SENSOR_6 shouldn't be set with only 4 HOTENDS." #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 4 HOTENDS." #endif #elif TEMP_SENSOR_3 != 0 #error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS." #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS." #elif TEMP_SENSOR_5 != 0 #error "TEMP_SENSOR_5 shouldn't be set with only 3 HOTENDS." #elif TEMP_SENSOR_6 != 0 #error "TEMP_SENSOR_6 shouldn't be set with only 3 HOTENDS." #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 3 HOTENDS." #endif #elif TEMP_SENSOR_2 != 0 #error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_3 != 0 #error "TEMP_SENSOR_3 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_5 != 0 #error "TEMP_SENSOR_5 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_6 != 0 #error "TEMP_SENSOR_6 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 2 HOTENDS." #endif #elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT) #error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_2 != 0 #error "TEMP_SENSOR_2 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_3 != 0 #error "TEMP_SENSOR_3 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_5 != 0 #error "TEMP_SENSOR_5 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_6 != 0 #error "TEMP_SENSOR_6 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_7 != 0 #error "TEMP_SENSOR_7 shouldn't be set with only 1 HOTEND." #endif #if TEMP_SENSOR_CHAMBER && !PIN_EXISTS(TEMP_CHAMBER) #error "TEMP_SENSOR_CHAMBER requires TEMP_CHAMBER_PIN. Please add it to your configuration." #endif #if TEMP_SENSOR_PROBE #if !PIN_EXISTS(TEMP_PROBE) #error "TEMP_SENSOR_PROBE requires TEMP_PROBE_PIN. Please add it to your configuration." #elif !HAS_TEMP_ADC_PROBE #error "TEMP_PROBE_PIN must be an ADC pin." #elif !ENABLED(FIX_MOUNTED_PROBE) #error "TEMP_SENSOR_PROBE shouldn't be set without FIX_MOUNTED_PROBE." #endif #endif #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0 #error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT." #endif /** * Test Heater, Temp Sensor, and Extruder Pins */ #if !HAS_HEATER_0 && EXTRUDERS #error "HEATER_0_PIN not defined for this board." #elif !ANY_PIN(TEMP_0, MAX6675_SS) #error "TEMP_0_PIN not defined for this board." #elif ((defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && !PINS_EXIST(E0_STEP, E0_DIR)) #error "E0_STEP_PIN or E0_DIR_PIN not defined for this board." #elif ( !(defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PINS_EXIST(E0_STEP, E0_DIR) || !HAS_E0_ENABLE)) #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." #elif EXTRUDERS && TEMP_SENSOR_0 == 0 #error "TEMP_SENSOR_0 is required if there are any extruders." #endif // Pins are required for heaters #if ENABLED(HEATER_0_USES_MAX6675) && !PIN_EXISTS(MAX6675_SS) #error "MAX6675_SS_PIN (required for TEMP_SENSOR_0) not defined for this board." #elif HAS_HOTEND && !HAS_TEMP_HOTEND #error "TEMP_0_PIN (required for TEMP_SENSOR_0) not defined for this board." #elif EITHER(HAS_MULTI_HOTEND, HEATERS_PARALLEL) && !HAS_HEATER_1 #error "HEATER_1_PIN is not defined. TEMP_SENSOR_1 might not be set, or the board (not EEB / EEF?) doesn't define a pin." #endif /** * Temperature status LEDs */ #if ENABLED(TEMP_STAT_LEDS) && !ANY_PIN(STAT_LED_RED, STAT_LED_BLUE) #error "TEMP_STAT_LEDS requires STAT_LED_RED_PIN or STAT_LED_BLUE_PIN, preferably both." #endif /** * LED Control Menu */ #if ENABLED(LED_CONTROL_MENU) && !HAS_COLOR_LEDS #error "LED_CONTROL_MENU requires BLINKM, RGB_LED, RGBW_LED, PCA9533, PCA9632, or NEOPIXEL_LED." #endif /** * LED Backlight Timeout */ #if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1)) #error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch." #endif /** * Basic multi hotend duplication mode */ #if ENABLED(MULTI_NOZZLE_DUPLICATION) #if HOTENDS < 2 #error "MULTI_NOZZLE_DUPLICATION requires 2 or more hotends." #elif ENABLED(DUAL_X_CARRIAGE) #error "MULTI_NOZZLE_DUPLICATION is incompatible with DUAL_X_CARRIAGE." #elif ENABLED(SINGLENOZZLE) #error "MULTI_NOZZLE_DUPLICATION is incompatible with SINGLENOZZLE." #elif ENABLED(MIXING_EXTRUDER) #error "MULTI_NOZZLE_DUPLICATION is incompatible with MIXING_EXTRUDER." #elif ENABLED(SWITCHING_EXTRUDER) #error "MULTI_NOZZLE_DUPLICATION is incompatible with SWITCHING_EXTRUDER." #endif #endif /** * Test Extruder Stepper Pins */ #if DISABLED(MK2_MULTIPLEXER) // MK2_MULTIPLEXER uses E0 stepper only #if E_STEPPERS #if !(PINS_EXIST(E0_STEP, E0_DIR) && HAS_E0_ENABLE) #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 1 #if !(PINS_EXIST(E1_STEP, E1_DIR) && HAS_E1_ENABLE) #error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 2 #if !(PINS_EXIST(E2_STEP, E2_DIR) && HAS_E2_ENABLE) #error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 3 #if !(PINS_EXIST(E3_STEP, E3_DIR) && HAS_E3_ENABLE) #error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 4 #if !(PINS_EXIST(E4_STEP, E4_DIR) && HAS_E4_ENABLE) #error "E4_STEP_PIN, E4_DIR_PIN, or E4_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 5 #if !(PINS_EXIST(E5_STEP, E5_DIR) && HAS_E5_ENABLE) #error "E5_STEP_PIN, E5_DIR_PIN, or E5_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 6 #if !(PINS_EXIST(E6_STEP, E6_DIR) && HAS_E6_ENABLE) #error "E6_STEP_PIN, E6_DIR_PIN, or E6_ENABLE_PIN not defined for this board." #endif #if E_STEPPERS > 7 #if !(PINS_EXIST(E7_STEP, E7_DIR) && HAS_E7_ENABLE) #error "E7_STEP_PIN, E7_DIR_PIN, or E7_ENABLE_PIN not defined for this board." #endif #endif // E_STEPPERS > 7 #endif // E_STEPPERS > 6 #endif // E_STEPPERS > 5 #endif // E_STEPPERS > 4 #endif // E_STEPPERS > 3 #endif // E_STEPPERS > 2 #endif // E_STEPPERS > 1 #endif // E_STEPPERS #endif /** * Endstop Tests */ #define _PLUG_UNUSED_TEST(A,P) (DISABLED(USE_##P##MIN_PLUG, USE_##P##MAX_PLUG) \ && !(ENABLED(A##_DUAL_ENDSTOPS) && WITHIN(A##2_USE_ENDSTOP, _##P##MAX_, _##P##MIN_)) \ && !(ENABLED(A##_MULTI_ENDSTOPS) && WITHIN(A##2_USE_ENDSTOP, _##P##MAX_, _##P##MIN_)) ) #define _AXIS_PLUG_UNUSED_TEST(A) (_PLUG_UNUSED_TEST(A,X) && _PLUG_UNUSED_TEST(A,Y) && _PLUG_UNUSED_TEST(A,Z)) // At least 3 endstop plugs must be used #if _AXIS_PLUG_UNUSED_TEST(X) #error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG." #endif #if _AXIS_PLUG_UNUSED_TEST(Y) #error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG." #endif #if _AXIS_PLUG_UNUSED_TEST(Z) #error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG." #endif // Delta and Cartesian use 3 homing endstops #if !IS_SCARA #if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG) #error "Enable USE_XMIN_PLUG when homing X to MIN." #elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG) #error "Enable USE_XMAX_PLUG when homing X to MAX." #elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG) #error "Enable USE_YMIN_PLUG when homing Y to MIN." #elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG) #error "Enable USE_YMAX_PLUG when homing Y to MAX." #endif #endif // Z homing direction and plug usage flags #if Z_HOME_DIR < 0 && NONE(USE_ZMIN_PLUG, HOMING_Z_WITH_PROBE) #error "Enable USE_ZMIN_PLUG when homing Z to MIN." #elif Z_HOME_DIR > 0 && ENABLED(USE_PROBE_FOR_Z_HOMING) #error "Z_HOME_DIR must be -1 when homing Z with the probe." #elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG) #error "Enable USE_ZMAX_PLUG when homing Z to MAX." #endif // Dual/multiple endstops requirements #if ENABLED(X_DUAL_ENDSTOPS) #if !X2_USE_ENDSTOP #error "You must set X2_USE_ENDSTOP with X_DUAL_ENDSTOPS." #elif X2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when X2_USE_ENDSTOP is _XMIN_." #elif X2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when X2_USE_ENDSTOP is _XMAX_." #elif X2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when X2_USE_ENDSTOP is _YMIN_." #elif X2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when X2_USE_ENDSTOP is _YMAX_." #elif X2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when X2_USE_ENDSTOP is _ZMIN_." #elif X2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when X2_USE_ENDSTOP is _ZMAX_." #elif !HAS_X2_MIN && !HAS_X2_MAX #error "X2_USE_ENDSTOP has been assigned to a nonexistent endstop!" #elif ENABLED(DELTA) #error "X_DUAL_ENDSTOPS is not compatible with DELTA." #endif #endif #if ENABLED(Y_DUAL_ENDSTOPS) #if !Y2_USE_ENDSTOP #error "You must set Y2_USE_ENDSTOP with Y_DUAL_ENDSTOPS." #elif Y2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when Y2_USE_ENDSTOP is _XMIN_." #elif Y2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when Y2_USE_ENDSTOP is _XMAX_." #elif Y2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when Y2_USE_ENDSTOP is _YMIN_." #elif Y2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when Y2_USE_ENDSTOP is _YMAX_." #elif Y2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when Y2_USE_ENDSTOP is _ZMIN_." #elif Y2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when Y2_USE_ENDSTOP is _ZMAX_." #elif !HAS_Y2_MIN && !HAS_Y2_MAX #error "Y2_USE_ENDSTOP has been assigned to a nonexistent endstop!" #elif ENABLED(DELTA) #error "Y_DUAL_ENDSTOPS is not compatible with DELTA." #endif #endif #if ENABLED(Z_MULTI_ENDSTOPS) #if !Z2_USE_ENDSTOP #error "You must set Z2_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 2." #elif Z2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when Z2_USE_ENDSTOP is _XMIN_." #elif Z2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when Z2_USE_ENDSTOP is _XMAX_." #elif Z2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when Z2_USE_ENDSTOP is _YMIN_." #elif Z2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when Z2_USE_ENDSTOP is _YMAX_." #elif Z2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when Z2_USE_ENDSTOP is _ZMIN_." #elif Z2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when Z2_USE_ENDSTOP is _ZMAX_." #elif !HAS_Z2_MIN && !HAS_Z2_MAX #error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!" #elif ENABLED(DELTA) #error "Z_MULTI_ENDSTOPS is not compatible with DELTA." #endif #if NUM_Z_STEPPER_DRIVERS >= 3 #if !Z3_USE_ENDSTOP #error "You must set Z3_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 3." #elif Z3_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when Z3_USE_ENDSTOP is _XMIN_." #elif Z3_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when Z3_USE_ENDSTOP is _XMAX_." #elif Z3_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when Z3_USE_ENDSTOP is _YMIN_." #elif Z3_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when Z3_USE_ENDSTOP is _YMAX_." #elif Z3_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when Z3_USE_ENDSTOP is _ZMIN_." #elif Z3_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when Z3_USE_ENDSTOP is _ZMAX_." #elif !HAS_Z3_MIN && !HAS_Z3_MAX #error "Z3_USE_ENDSTOP has been assigned to a nonexistent endstop!" #endif #endif #if NUM_Z_STEPPER_DRIVERS >= 4 #if !Z4_USE_ENDSTOP #error "You must set Z4_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 4." #elif Z4_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when Z4_USE_ENDSTOP is _XMIN_." #elif Z4_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when Z4_USE_ENDSTOP is _XMAX_." #elif Z4_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when Z4_USE_ENDSTOP is _YMIN_." #elif Z4_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when Z4_USE_ENDSTOP is _YMAX_." #elif Z4_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when Z4_USE_ENDSTOP is _ZMIN_." #elif Z4_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when Z4_USE_ENDSTOP is _ZMAX_." #elif !HAS_Z4_MIN && !HAS_Z4_MAX #error "Z4_USE_ENDSTOP has been assigned to a nonexistent endstop!" #endif #endif #endif #if defined(ENDSTOP_NOISE_THRESHOLD) && !WITHIN(ENDSTOP_NOISE_THRESHOLD, 2, 7) #error "ENDSTOP_NOISE_THRESHOLD must be an integer from 2 to 7." #endif /** * emergency-command parser */ #if ENABLED(EMERGENCY_PARSER) && defined(__AVR__) && defined(USBCON) #error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)." #endif /** * I2C bus */ #if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0 #if I2C_SLAVE_ADDRESS < 8 #error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)" #elif I2C_SLAVE_ADDRESS > 127 #error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)" #endif #endif /** * G35 Assisted Tramming */ #if ENABLED(ASSISTED_TRAMMING) && !HAS_BED_PROBE #error "ASSISTED_TRAMMING requires a bed probe." #endif /** * G38 Probe Target */ #if ENABLED(G38_PROBE_TARGET) #if !HAS_BED_PROBE #error "G38_PROBE_TARGET requires a bed probe." #elif !IS_CARTESIAN #error "G38_PROBE_TARGET requires a Cartesian machine." #endif #endif /** * RGB_LED Requirements */ #define _RGB_TEST (PINS_EXIST(RGB_LED_R, RGB_LED_G, RGB_LED_B)) #if ENABLED(PRINTER_EVENT_LEDS) && !HAS_COLOR_LEDS #error "PRINTER_EVENT_LEDS requires BLINKM, PCA9533, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED." #elif ENABLED(RGB_LED) #if !_RGB_TEST #error "RGB_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, and RGB_LED_B_PIN." #elif ENABLED(RGBW_LED) #error "Please enable only one of RGB_LED and RGBW_LED." #endif #elif ENABLED(RGBW_LED) #if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W)) #error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN." #endif #elif ENABLED(NEOPIXEL_LED) #if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0) #error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS." #endif #endif #undef _RGB_TEST #if DISABLED(NO_COMPILE_TIME_PWM) #define _TEST_PWM(P) PWM_PIN(P) #else #define _TEST_PWM(P) 1 // pass #endif /** * Auto Fan check for PWM pins */ #if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255 #define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255." #if HAS_AUTO_FAN_0 static_assert(_TEST_PWM(E0_AUTO_FAN_PIN), "E0" AF_ERR_SUFF); #elif HAS_AUTO_FAN_1 static_assert(_TEST_PWM(E1_AUTO_FAN_PIN), "E1" AF_ERR_SUFF); #elif HAS_AUTO_FAN_2 static_assert(_TEST_PWM(E2_AUTO_FAN_PIN), "E2" AF_ERR_SUFF); #elif HAS_AUTO_FAN_3 static_assert(_TEST_PWM(E3_AUTO_FAN_PIN), "E3" AF_ERR_SUFF); #elif HAS_AUTO_FAN_4 static_assert(_TEST_PWM(E4_AUTO_FAN_PIN), "E4" AF_ERR_SUFF); #elif HAS_AUTO_FAN_5 static_assert(_TEST_PWM(E5_AUTO_FAN_PIN), "E5" AF_ERR_SUFF); #elif HAS_AUTO_FAN_6 static_assert(_TEST_PWM(E6_AUTO_FAN_PIN), "E6" AF_ERR_SUFF); #elif HAS_AUTO_FAN_7 static_assert(_TEST_PWM(E7_AUTO_FAN_PIN), "E7" AF_ERR_SUFF); #endif #endif /** * Make sure only one EEPROM type is enabled */ #if ENABLED(EEPROM_SETTINGS) #if 1 < 0 \ + ENABLED(I2C_EEPROM) \ + ENABLED(SPI_EEPROM) \ + ENABLED(QSPI_EEPROM) \ + ENABLED(SDCARD_EEPROM_EMULATION) \ + ENABLED(FLASH_EEPROM_EMULATION) \ + ENABLED(SRAM_EEPROM_EMULATION) \ + ENABLED(IIC_BL24CXX_EEPROM) #error "Please select only one method of EEPROM Persistent Storage." #endif #endif /** * Make sure features that need to write to the SD card are * disabled unless write support is enabled. */ #if ENABLED(SDCARD_READONLY) #if ENABLED(POWER_LOSS_RECOVERY) #error "POWER_LOSS_RECOVERY is incompatible with SDCARD_READONLY." #elif ENABLED(BINARY_FILE_TRANSFER) #error "BINARY_FILE_TRANSFER is incompatible with SDCARD_READONLY." #elif ENABLED(SDCARD_EEPROM_EMULATION) #error "SDCARD_EEPROM_EMULATION is incompatible with SDCARD_READONLY." #endif #endif /** * Make sure only one display is enabled */ #if 1 < 0 \ + (ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(IS_RRD_SC)) \ + (ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(IS_RRD_FG_SC)) \ + (ENABLED(ULTRA_LCD) && DISABLED(IS_ULTRA_LCD)) \ + (ENABLED(U8GLIB_SSD1306) && DISABLED(IS_U8GLIB_SSD1306)) \ + (ENABLED(MINIPANEL) && DISABLED(MKS_MINI_12864, ENDER2_STOCKDISPLAY)) \ + (ENABLED(MKS_MINI_12864) && DISABLED(MKS_LCD12864)) \ + (ENABLED(EXTENSIBLE_UI) && DISABLED(IS_EXTUI)) \ + (ENABLED(ULTIPANEL) && DISABLED(IS_ULTIPANEL)) \ + ENABLED(RADDS_DISPLAY) \ + ENABLED(ULTIMAKERCONTROLLER) \ + ENABLED(PANEL_ONE) \ + ENABLED(G3D_PANEL) \ + ENABLED(RIGIDBOT_PANEL) \ + ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ + ENABLED(ZONESTAR_LCD) \ + ENABLED(RA_CONTROL_PANEL) \ + ENABLED(LCD_SAINSMART_I2C_1602) \ + ENABLED(LCD_SAINSMART_I2C_2004) \ + ENABLED(LCM1602) \ + ENABLED(LCD_I2C_PANELOLU2) \ + ENABLED(LCD_I2C_VIKI) \ + ENABLED(SAV_3DLCD) \ + ENABLED(FF_INTERFACEBOARD) \ + ENABLED(REPRAPWORLD_GRAPHICAL_LCD) \ + ENABLED(VIKI2) \ + ENABLED(miniVIKI) \ + ENABLED(MAKRPANEL) \ + ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ + ENABLED(BQ_LCD_SMART_CONTROLLER) \ + ENABLED(CARTESIO_UI) \ + ENABLED(LCD_FOR_MELZI) \ + ENABLED(ULTI_CONTROLLER) \ + ENABLED(MKS_LCD12864) \ + ENABLED(ENDER2_STOCKDISPLAY) \ + ENABLED(FYSETC_MINI_12864_X_X) \ + ENABLED(FYSETC_MINI_12864_1_2) \ + ENABLED(FYSETC_MINI_12864_2_0) \ + ENABLED(FYSETC_MINI_12864_2_1) \ + ENABLED(FYSETC_GENERIC_12864_1_1) \ + ENABLED(CR10_STOCKDISPLAY) \ + ENABLED(DWIN_CREALITY_LCD) \ + ENABLED(ANET_FULL_GRAPHICS_LCD) \ + ENABLED(AZSMZ_12864) \ + ENABLED(SILVER_GATE_GLCD_CONTROLLER) \ + ENABLED(SAV_3DGLCD) \ + ENABLED(OLED_PANEL_TINYBOY2) \ + ENABLED(MKS_12864OLED) \ + ENABLED(MKS_12864OLED_SSD1306) \ + ENABLED(ZONESTAR_12864LCD) \ + ENABLED(ZONESTAR_12864OLED) \ + ENABLED(ZONESTAR_12864OLED_SSD1306) \ + ENABLED(U8GLIB_SH1106_EINSTART) \ + ENABLED(OVERLORD_OLED) \ + ENABLED(FYSETC_242_OLED_12864) \ + ENABLED(DGUS_LCD_UI_ORIGIN) \ + ENABLED(DGUS_LCD_UI_FYSETC) \ + ENABLED(DGUS_LCD_UI_HIPRECY) \ + ENABLED(MALYAN_LCD) \ + ENABLED(TOUCH_UI_FTDI_EVE) \ + ENABLED(TFT_320x240) \ + ENABLED(TFT_320x240_SPI) \ + ENABLED(FSMC_GRAPHICAL_TFT) \ + ENABLED(TFT_LVGL_UI_FSMC) \ + ENABLED(TFT_LVGL_UI_SPI) \ + ENABLED(ANYCUBIC_LCD_I3MEGA) \ + ENABLED(ANYCUBIC_LCD_CHIRON) #error "Please select only one LCD controller option." #endif #undef IS_RRD_SC #undef IS_RRD_FG_SC #undef IS_ULTRA_LCD #undef IS_U8GLIB_SSD1306 #undef IS_RRW_KEYPAD #undef IS_EXTUI #undef IS_ULTIPANEL #if 1 < ENABLED(LCD_SCREEN_ROT_0) + ENABLED(LCD_SCREEN_ROT_90) + ENABLED(LCD_SCREEN_ROT_180) + ENABLED(LCD_SCREEN_ROT_270) #error "Please enable only one LCD_SCREEN_ROT_* option: 0, 90, 180, or 270." #endif /** * FYSETC Mini 12864 RGB backlighting required */ #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) && DISABLED(RGB_LED) #error "RGB_LED is required for FYSETC_MINI_12864 1.2 and 2.0." #elif EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) && DISABLED(LED_USER_PRESET_STARTUP) #error "LED_USER_PRESET_STARTUP is required for FYSETC_MINI_12864 2.x displays." #endif /** * Check existing CS pins against enabled TMC SPI drivers. */ #define INVALID_TMC_SPI(ST) (AXIS_HAS_SPI(ST) && !PIN_EXISTS(ST##_CS)) #if INVALID_TMC_SPI(X) #error "An SPI driven TMC driver on X requires X_CS_PIN." #elif INVALID_TMC_SPI(X2) #error "An SPI driven TMC driver on X2 requires X2_CS_PIN." #elif INVALID_TMC_SPI(Y) #error "An SPI driven TMC driver on Y requires Y_CS_PIN." #elif INVALID_TMC_SPI(Y2) #error "An SPI driven TMC driver on Y2 requires Y2_CS_PIN." #elif INVALID_TMC_SPI(Z) #error "An SPI driven TMC driver on Z requires Z_CS_PIN." #elif INVALID_TMC_SPI(Z2) #error "An SPI driven TMC driver on Z2 requires Z2_CS_PIN." #elif INVALID_TMC_SPI(Z3) #error "An SPI driven TMC driver on Z3 requires Z3_CS_PIN." #elif INVALID_TMC_SPI(Z4) #error "An SPI driven TMC driver on Z4 requires Z4_CS_PIN." #elif INVALID_TMC_SPI(E0) #error "An SPI driven TMC driver on E0 requires E0_CS_PIN." #elif INVALID_TMC_SPI(E1) #error "An SPI driven TMC driver on E1 requires E1_CS_PIN." #elif INVALID_TMC_SPI(E2) #error "An SPI driven TMC driver on E2 requires E2_CS_PIN." #elif INVALID_TMC_SPI(E3) #error "An SPI driven TMC driver on E3 requires E3_CS_PIN." #elif INVALID_TMC_SPI(E4) #error "An SPI driven TMC driver on E4 requires E4_CS_PIN." #elif INVALID_TMC_SPI(E5) #error "An SPI driven TMC driver on E5 requires E5_CS_PIN." #elif INVALID_TMC_SPI(E6) #error "An SPI driven TMC driver on E6 requires E6_CS_PIN." #elif INVALID_TMC_SPI(E7) #error "An SPI driven TMC driver on E7 requires E7_CS_PIN." #endif #undef INVALID_TMC_SPI /** * Check existing RX/TX pins against enable TMC UART drivers. */ #define INVALID_TMC_UART(ST) (AXIS_HAS_UART(ST) && !(defined(ST##_HARDWARE_SERIAL) || (PINS_EXIST(ST##_SERIAL_RX, ST##_SERIAL_TX)))) #if INVALID_TMC_UART(X) #error "TMC2208 or TMC2209 on X requires X_HARDWARE_SERIAL or X_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(X2) #error "TMC2208 or TMC2209 on X2 requires X2_HARDWARE_SERIAL or X2_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(Y) #error "TMC2208 or TMC2209 on Y requires Y_HARDWARE_SERIAL or Y_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(Y2) #error "TMC2208 or TMC2209 on Y2 requires Y2_HARDWARE_SERIAL or Y2_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(Z) #error "TMC2208 or TMC2209 on Z requires Z_HARDWARE_SERIAL or Z_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(Z2) #error "TMC2208 or TMC2209 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(Z3) #error "TMC2208 or TMC2209 on Z3 requires Z3_HARDWARE_SERIAL or Z3_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(Z4) #error "TMC2208 or TMC2209 on Z4 requires Z4_HARDWARE_SERIAL or Z4_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E0) #error "TMC2208 or TMC2209 on E0 requires E0_HARDWARE_SERIAL or E0_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E1) #error "TMC2208 or TMC2209 on E1 requires E1_HARDWARE_SERIAL or E1_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E2) #error "TMC2208 or TMC2209 on E2 requires E2_HARDWARE_SERIAL or E2_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E3) #error "TMC2208 or TMC2209 on E3 requires E3_HARDWARE_SERIAL or E3_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E4) #error "TMC2208 or TMC2209 on E4 requires E4_HARDWARE_SERIAL or E4_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E5) #error "TMC2208 or TMC2209 on E5 requires E5_HARDWARE_SERIAL or E5_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E6) #error "TMC2208 or TMC2209 on E6 requires E6_HARDWARE_SERIAL or E6_SERIAL_(RX|TX)_PIN." #elif INVALID_TMC_UART(E7) #error "TMC2208 or TMC2209 on E7 requires E7_HARDWARE_SERIAL or E7_SERIAL_(RX|TX)_PIN." #endif #undef INVALID_TMC_UART /** * TMC2209 slave address values */ #define INVALID_TMC_ADDRESS(ST) static_assert(0 <= ST##_SLAVE_ADDRESS && ST##_SLAVE_ADDRESS <= 3, "TMC2209 slave address must be 0, 1, 2 or 3") #if AXIS_DRIVER_TYPE_X(TMC2209) INVALID_TMC_ADDRESS(X); #elif AXIS_DRIVER_TYPE_X2(TMC2209) INVALID_TMC_ADDRESS(X2); #elif AXIS_DRIVER_TYPE_Y(TMC2209) INVALID_TMC_ADDRESS(Y); #elif AXIS_DRIVER_TYPE_Y2(TMC2209) INVALID_TMC_ADDRESS(Y2); #elif AXIS_DRIVER_TYPE_Z(TMC2209) INVALID_TMC_ADDRESS(Z); #elif AXIS_DRIVER_TYPE_Z2(TMC2209) INVALID_TMC_ADDRESS(Z2); #elif AXIS_DRIVER_TYPE_Z3(TMC2209) INVALID_TMC_ADDRESS(Z3); #elif AXIS_DRIVER_TYPE_Z4(TMC2209) INVALID_TMC_ADDRESS(Z4); #elif AXIS_DRIVER_TYPE_E0(TMC2209) INVALID_TMC_ADDRESS(E0); #elif AXIS_DRIVER_TYPE_E1(TMC2209) INVALID_TMC_ADDRESS(E1); #elif AXIS_DRIVER_TYPE_E2(TMC2209) INVALID_TMC_ADDRESS(E2); #elif AXIS_DRIVER_TYPE_E3(TMC2209) INVALID_TMC_ADDRESS(E3); #elif AXIS_DRIVER_TYPE_E4(TMC2209) INVALID_TMC_ADDRESS(E4); #elif AXIS_DRIVER_TYPE_E5(TMC2209) INVALID_TMC_ADDRESS(E5); #elif AXIS_DRIVER_TYPE_E6(TMC2209) INVALID_TMC_ADDRESS(E6); #elif AXIS_DRIVER_TYPE_E7(TMC2209) INVALID_TMC_ADDRESS(E7); #endif #undef INVALID_TMC_ADDRESS #define _TMC_MICROSTEP_IS_VALID(MS) (MS == 0 || MS == 2 || MS == 4 || MS == 8 || MS == 16 || MS == 32 || MS == 64 || MS == 128 || MS == 256) #define TMC_MICROSTEP_IS_VALID(M) (!AXIS_IS_TMC(M) || _TMC_MICROSTEP_IS_VALID(M##_MICROSTEPS)) #define INVALID_TMC_MS(ST) static_assert(0, "Invalid " STRINGIFY(ST) "_MICROSTEPS. Valid values are 0, 2, 4, 8, 16, 32, 64, 128, and 256.") #if !TMC_MICROSTEP_IS_VALID(X) INVALID_TMC_MS(X); #elif !TMC_MICROSTEP_IS_VALID(Y) INVALID_TMC_MS(Y) #elif !TMC_MICROSTEP_IS_VALID(Z) INVALID_TMC_MS(Z) #elif !TMC_MICROSTEP_IS_VALID(X2) INVALID_TMC_MS(X2); #elif !TMC_MICROSTEP_IS_VALID(Y2) INVALID_TMC_MS(Y2) #elif !TMC_MICROSTEP_IS_VALID(Z2) INVALID_TMC_MS(Z2) #elif !TMC_MICROSTEP_IS_VALID(Z3) INVALID_TMC_MS(Z3) #elif !TMC_MICROSTEP_IS_VALID(Z4) INVALID_TMC_MS(Z4) #elif !TMC_MICROSTEP_IS_VALID(E0) INVALID_TMC_MS(E0) #elif !TMC_MICROSTEP_IS_VALID(E1) INVALID_TMC_MS(E1) #elif !TMC_MICROSTEP_IS_VALID(E2) INVALID_TMC_MS(E2) #elif !TMC_MICROSTEP_IS_VALID(E3) INVALID_TMC_MS(E3) #elif !TMC_MICROSTEP_IS_VALID(E4) INVALID_TMC_MS(E4) #elif !TMC_MICROSTEP_IS_VALID(E5) INVALID_TMC_MS(E5) #elif !TMC_MICROSTEP_IS_VALID(E6) INVALID_TMC_MS(E6) #elif !TMC_MICROSTEP_IS_VALID(E7) INVALID_TMC_MS(E7) #endif #undef INVALID_TMC_MS #undef TMC_MICROSTEP_IS_VALID #undef _TMC_MICROSTEP_IS_VALID #if ENABLED(DELTA) && (ENABLED(STEALTHCHOP_XY) != ENABLED(STEALTHCHOP_Z)) #error "STEALTHCHOP_XY and STEALTHCHOP_Z must be the same on DELTA." #endif #if ENABLED(SENSORLESS_HOMING) // Require STEALTHCHOP for SENSORLESS_HOMING on DELTA as the transition from spreadCycle to stealthChop // is necessary in order to reset the stallGuard indication between the initial movement of all three // towers to +Z and the individual homing of each tower. This restriction can be removed once a means of // clearing the stallGuard activated status is found. // Stall detection DIAG = HIGH : TMC2209 // Stall detection DIAG = LOW : TMC2130/TMC2160/TMC2660/TMC5130/TMC5160 #define X_ENDSTOP_INVERTING !AXIS_DRIVER_TYPE(X,TMC2209) #define Y_ENDSTOP_INVERTING !AXIS_DRIVER_TYPE(Y,TMC2209) #define Z_ENDSTOP_INVERTING !AXIS_DRIVER_TYPE(Z,TMC2209) #if ENABLED(DELTA) && !BOTH(STEALTHCHOP_XY, STEALTHCHOP_Z) #error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP_XY and STEALTHCHOP_Z." #elif X_SENSORLESS && X_HOME_DIR < 0 && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_XMIN) #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_XMIN (or ENDSTOPPULLUPS) when homing to X_MIN." #elif X_SENSORLESS && X_HOME_DIR > 0 && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_XMAX) #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_XMAX (or ENDSTOPPULLUPS) when homing to X_MAX." #elif Y_SENSORLESS && Y_HOME_DIR < 0 && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_YMIN) #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_YMIN (or ENDSTOPPULLUPS) when homing to Y_MIN." #elif Y_SENSORLESS && Y_HOME_DIR > 0 && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_YMAX) #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_YMAX (or ENDSTOPPULLUPS) when homing to Y_MAX." #elif Z_SENSORLESS && Z_HOME_DIR < 0 && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_ZMIN) #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_ZMIN (or ENDSTOPPULLUPS) when homing to Z_MIN." #elif Z_SENSORLESS && Z_HOME_DIR > 0 && NONE(ONBOARD_ENDSTOPPULLUPS, ENDSTOPPULLUPS, ENDSTOPPULLUP_ZMAX) #error "SENSORLESS_HOMING requires ENDSTOPPULLUP_ZMAX (or ENDSTOPPULLUPS) when homing to Z_MAX." #elif X_SENSORLESS && X_HOME_DIR < 0 && X_MIN_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING #if X_ENDSTOP_INVERTING #error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING = true when homing to X_MIN." #else #error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING = false when homing TMC2209 to X_MIN." #endif #elif X_SENSORLESS && X_HOME_DIR > 0 && X_MAX_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING #if X_ENDSTOP_INVERTING #error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING = true when homing to X_MAX." #else #error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING = false when homing TMC2209 to X_MAX." #endif #elif Y_SENSORLESS && Y_HOME_DIR < 0 && Y_MIN_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING #if Y_ENDSTOP_INVERTING #error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING = true when homing to Y_MIN." #else #error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING = false when homing TMC2209 to Y_MIN." #endif #elif Y_SENSORLESS && Y_HOME_DIR > 0 && Y_MAX_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING #if Y_ENDSTOP_INVERTING #error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING = true when homing to Y_MAX." #else #error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING = false when homing TMC2209 to Y_MAX." #endif #elif Z_SENSORLESS && Z_HOME_DIR < 0 && Z_MIN_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING #if Z_ENDSTOP_INVERTING #error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING = true when homing to Z_MIN." #else #error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING = false when homing TMC2209 to Z_MIN." #endif #elif Z_SENSORLESS && Z_HOME_DIR > 0 && Z_MAX_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING #if Z_ENDSTOP_INVERTING #error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING = true when homing to Z_MAX." #else #error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING = false when homing TMC2209 to Z_MAX." #endif #elif ENDSTOP_NOISE_THRESHOLD #error "SENSORLESS_HOMING is incompatible with ENDSTOP_NOISE_THRESHOLD." #elif !(X_SENSORLESS || Y_SENSORLESS || Z_SENSORLESS) #error "SENSORLESS_HOMING requires a TMC stepper driver with StallGuard on X, Y, or Z axes." #endif #undef X_ENDSTOP_INVERTING #undef Y_ENDSTOP_INVERTING #undef Z_ENDSTOP_INVERTING #endif // Sensorless probing requirements #if ENABLED(SENSORLESS_PROBING) #if ENABLED(DELTA) && !(X_SENSORLESS && Y_SENSORLESS && Z_SENSORLESS) #error "SENSORLESS_PROBING for DELTA requires TMC stepper drivers with StallGuard on X, Y, and Z axes." #elif !Z_SENSORLESS #error "SENSORLESS_PROBING requires a TMC stepper driver with StallGuard on Z." #endif #endif // Sensorless homing is required for both combined steppers in an H-bot #if CORE_IS_XY && X_SENSORLESS != Y_SENSORLESS #error "CoreXY requires both X and Y to use sensorless homing if either one does." #elif CORE_IS_XZ && X_SENSORLESS != Z_SENSORLESS && !HOMING_Z_WITH_PROBE #error "CoreXZ requires both X and Z to use sensorless homing if either one does." #elif CORE_IS_YZ && Y_SENSORLESS != Z_SENSORLESS && !HOMING_Z_WITH_PROBE #error "CoreYZ requires both Y and Z to use sensorless homing if either one does." #endif // Other TMC feature requirements #if ENABLED(HYBRID_THRESHOLD) && !STEALTHCHOP_ENABLED #error "Enable STEALTHCHOP_(XY|Z|E) to use HYBRID_THRESHOLD." #elif ENABLED(SENSORLESS_HOMING) && !HAS_STALLGUARD #error "SENSORLESS_HOMING requires TMC2130, TMC2160, TMC2209, TMC2660, or TMC5160 stepper drivers." #elif ENABLED(SENSORLESS_PROBING) && !HAS_STALLGUARD #error "SENSORLESS_PROBING requires TMC2130, TMC2160, TMC2209, TMC2660, or TMC5160 stepper drivers." #elif STEALTHCHOP_ENABLED && !HAS_STEALTHCHOP #error "STEALTHCHOP requires TMC2130, TMC2160, TMC2208, TMC2209, or TMC5160 stepper drivers." #endif /** * TMC SPI Chaining */ #define IN_CHAIN(A) ((A##_CHAIN_POS > 0) && !HAS_L64XX) #if IN_CHAIN(X ) || IN_CHAIN(Y ) || IN_CHAIN(Z ) || IN_CHAIN(X2) || IN_CHAIN(Y2) || IN_CHAIN(Z2) || IN_CHAIN(Z3) || IN_CHAIN(Z4) \ || IN_CHAIN(E0) || IN_CHAIN(E1) || IN_CHAIN(E2) || IN_CHAIN(E3) || IN_CHAIN(E4) || IN_CHAIN(E5) || IN_CHAIN(E6) || IN_CHAIN(E7) #define BAD_CHAIN(A) (IN_CHAIN(A) && !PIN_EXISTS(A##_CS)) #if BAD_CHAIN(X ) || BAD_CHAIN(Y ) || BAD_CHAIN(Z ) || BAD_CHAIN(X2) || BAD_CHAIN(Y2) || BAD_CHAIN(Z2) || BAD_CHAIN(Z3) || BAD_CHAIN(Z4) \ || BAD_CHAIN(E0) || BAD_CHAIN(E1) || BAD_CHAIN(E2) || BAD_CHAIN(E3) || BAD_CHAIN(E4) || BAD_CHAIN(E5) || BAD_CHAIN(E6) || BAD_CHAIN(E7) #error "All chained TMC drivers need a CS pin." #else #if IN_CHAIN(X) #define CS_COMPARE X_CS_PIN #elif IN_CHAIN(Y) #define CS_COMPARE Y_CS_PIN #elif IN_CHAIN(Z) #define CS_COMPARE Z_CS_PIN #elif IN_CHAIN(X2) #define CS_COMPARE X2_CS_PIN #elif IN_CHAIN(Y2) #define CS_COMPARE Y2_CS_PIN #elif IN_CHAIN(Z2) #define CS_COMPARE Z2_CS_PIN #elif IN_CHAIN(Z3) #define CS_COMPARE Z3_CS_PIN #elif IN_CHAIN(E0) #define CS_COMPARE E0_CS_PIN #elif IN_CHAIN(E1) #define CS_COMPARE E1_CS_PIN #elif IN_CHAIN(E2) #define CS_COMPARE E2_CS_PIN #elif IN_CHAIN(E3) #define CS_COMPARE E3_CS_PIN #elif IN_CHAIN(E4) #define CS_COMPARE E4_CS_PIN #elif IN_CHAIN(E5) #define CS_COMPARE E5_CS_PIN #elif IN_CHAIN(E6) #define CS_COMPARE E6_CS_PIN #elif IN_CHAIN(E7) #define CS_COMPARE E7_CS_PIN #endif #define BAD_CS_PIN(A) (IN_CHAIN(A) && A##_CS_PIN != CS_COMPARE) #if BAD_CS_PIN(X ) || BAD_CS_PIN(Y ) || BAD_CS_PIN(Z ) || BAD_CS_PIN(X2) || BAD_CS_PIN(Y2) || BAD_CS_PIN(Z2) || BAD_CS_PIN(Z3) || BAD_CS_PIN(Z4) \ || BAD_CS_PIN(E0) || BAD_CS_PIN(E1) || BAD_CS_PIN(E2) || BAD_CS_PIN(E3) || BAD_CS_PIN(E4) || BAD_CS_PIN(E5) || BAD_CS_PIN(E6) || BAD_CS_PIN(E7) #error "All chained TMC drivers must use the same CS pin." #endif #undef BAD_CS_PIN #undef CS_COMPARE #endif #undef BAD_CHAIN #endif #undef IN_CHAIN /** * Digipot requirement */ #if HAS_I2C_DIGIPOT #if BOTH(DIGIPOT_MCP4018, DIGIPOT_MCP4451) #error "Enable only one of DIGIPOT_MCP4018 or DIGIPOT_MCP4451." #elif !MB(MKS_SBASE) \ && (!defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1)) #error "DIGIPOT_MCP4018/4451 requires DIGIPOTS_I2C_SDA_* pins to be defined." #endif #endif /** * Check per-axis initializers for errors */ constexpr float sanity_arr_1[] = DEFAULT_AXIS_STEPS_PER_UNIT, sanity_arr_2[] = DEFAULT_MAX_FEEDRATE, sanity_arr_3[] = DEFAULT_MAX_ACCELERATION; #define _ARR_TEST(N,I) (sanity_arr_##N[_MIN(I,int(COUNT(sanity_arr_##N))-1)] > 0) static_assert(COUNT(sanity_arr_1) >= XYZE, "DEFAULT_AXIS_STEPS_PER_UNIT requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_1) <= XYZE_N, "DEFAULT_AXIS_STEPS_PER_UNIT has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); static_assert( _ARR_TEST(1,0) && _ARR_TEST(1,1) && _ARR_TEST(1,2) && _ARR_TEST(1,3) && _ARR_TEST(1,4) && _ARR_TEST(1,5) && _ARR_TEST(1,6) && _ARR_TEST(1,7) && _ARR_TEST(1,8), "DEFAULT_AXIS_STEPS_PER_UNIT values must be positive."); static_assert(COUNT(sanity_arr_2) >= XYZE, "DEFAULT_MAX_FEEDRATE requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_2) <= XYZE_N, "DEFAULT_MAX_FEEDRATE has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); static_assert( _ARR_TEST(2,0) && _ARR_TEST(2,1) && _ARR_TEST(2,2) && _ARR_TEST(2,3) && _ARR_TEST(2,4) && _ARR_TEST(2,5) && _ARR_TEST(2,6) && _ARR_TEST(2,7) && _ARR_TEST(2,8), "DEFAULT_MAX_FEEDRATE values must be positive."); static_assert(COUNT(sanity_arr_3) >= XYZE, "DEFAULT_MAX_ACCELERATION requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2) && _ARR_TEST(3,3) && _ARR_TEST(3,4) && _ARR_TEST(3,5) && _ARR_TEST(3,6) && _ARR_TEST(3,7) && _ARR_TEST(3,8), "DEFAULT_MAX_ACCELERATION values must be positive."); #if ENABLED(LIMITED_MAX_ACCEL_EDITING) #ifdef MAX_ACCEL_EDIT_VALUES constexpr float sanity_arr_4[] = MAX_ACCEL_EDIT_VALUES; static_assert(COUNT(sanity_arr_4) >= XYZE, "MAX_ACCEL_EDIT_VALUES requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_4) <= XYZE, "MAX_ACCEL_EDIT_VALUES has too many elements. X, Y, Z and E elements only."); static_assert( _ARR_TEST(4,0) && _ARR_TEST(4,1) && _ARR_TEST(4,2) && _ARR_TEST(4,3) && _ARR_TEST(4,4) && _ARR_TEST(4,5) && _ARR_TEST(4,6) && _ARR_TEST(4,7) && _ARR_TEST(4,8), "MAX_ACCEL_EDIT_VALUES values must be positive."); #endif #endif #if ENABLED(LIMITED_MAX_FR_EDITING) #ifdef MAX_FEEDRATE_EDIT_VALUES constexpr float sanity_arr_5[] = MAX_FEEDRATE_EDIT_VALUES; static_assert(COUNT(sanity_arr_5) >= XYZE, "MAX_FEEDRATE_EDIT_VALUES requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_5) <= XYZE, "MAX_FEEDRATE_EDIT_VALUES has too many elements. X, Y, Z and E elements only."); static_assert( _ARR_TEST(5,0) && _ARR_TEST(5,1) && _ARR_TEST(5,2) && _ARR_TEST(5,3) && _ARR_TEST(5,4) && _ARR_TEST(5,5) && _ARR_TEST(5,6) && _ARR_TEST(5,7) && _ARR_TEST(5,8), "MAX_FEEDRATE_EDIT_VALUES values must be positive."); #endif #endif #if ENABLED(LIMITED_JERK_EDITING) #ifdef MAX_JERK_EDIT_VALUES constexpr float sanity_arr_6[] = MAX_JERK_EDIT_VALUES; static_assert(COUNT(sanity_arr_6) >= XYZE, "MAX_JERK_EDIT_VALUES requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_6) <= XYZE, "MAX_JERK_EDIT_VALUES has too many elements. X, Y, Z and E elements only."); static_assert( _ARR_TEST(6,0) && _ARR_TEST(6,1) && _ARR_TEST(6,2) && _ARR_TEST(6,3) && _ARR_TEST(6,4) && _ARR_TEST(6,5) && _ARR_TEST(6,6) && _ARR_TEST(6,7) && _ARR_TEST(6,8), "MAX_JERK_EDIT_VALUES values must be positive."); #endif #endif #undef _ARR_TEST #if BOTH(CNC_COORDINATE_SYSTEMS, NO_WORKSPACE_OFFSETS) #error "CNC_COORDINATE_SYSTEMS is incompatible with NO_WORKSPACE_OFFSETS." #endif #if !BLOCK_BUFFER_SIZE || !IS_POWER_OF_2(BLOCK_BUFFER_SIZE) #error "BLOCK_BUFFER_SIZE must be a power of 2." #endif #if ENABLED(LED_CONTROL_MENU) && DISABLED(ULTIPANEL) #error "LED_CONTROL_MENU requires an LCD controller." #endif #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) && DISABLED(NEOPIXEL_LED) #error "CASE_LIGHT_USE_NEOPIXEL requires NEOPIXEL_LED." #endif #if ENABLED(SKEW_CORRECTION) #if !defined(XY_SKEW_FACTOR) && !(defined(XY_DIAG_AC) && defined(XY_DIAG_BD) && defined(XY_SIDE_AD)) #error "SKEW_CORRECTION requires XY_SKEW_FACTOR or XY_DIAG_AC, XY_DIAG_BD, XY_SIDE_AD." #endif #if ENABLED(SKEW_CORRECTION_FOR_Z) #if !defined(XZ_SKEW_FACTOR) && !(defined(XZ_DIAG_AC) && defined(XZ_DIAG_BD) && defined(XZ_SIDE_AD)) #error "SKEW_CORRECTION requires XZ_SKEW_FACTOR or XZ_DIAG_AC, XZ_DIAG_BD, XZ_SIDE_AD." #endif #if !defined(YZ_SKEW_FACTOR) && !(defined(YZ_DIAG_AC) && defined(YZ_DIAG_BD) && defined(YZ_SIDE_AD)) #error "SKEW_CORRECTION requires YZ_SKEW_FACTOR or YZ_DIAG_AC, YZ_DIAG_BD, YZ_SIDE_AD." #endif #endif #endif #if ENABLED(BACKUP_POWER_SUPPLY) && !PIN_EXISTS(POWER_LOSS) #error "BACKUP_POWER_SUPPLY requires a POWER_LOSS_PIN." #endif #if ENABLED(Z_STEPPER_AUTO_ALIGN) #if NUM_Z_STEPPER_DRIVERS <= 1 #error "Z_STEPPER_AUTO_ALIGN requires NUM_Z_STEPPER_DRIVERS greater than 1." #elif !HAS_BED_PROBE #error "Z_STEPPER_AUTO_ALIGN requires a Z-bed probe." #elif ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS) && NUM_Z_STEPPER_DRIVERS < 3 #error "Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS requires NUM_Z_STEPPER_DRIVERS to be 3 or 4." #endif #endif #if ENABLED(PRINTCOUNTER) && DISABLED(EEPROM_SETTINGS) #error "PRINTCOUNTER requires EEPROM_SETTINGS. Please update your Configuration." #endif #if ENABLED(USB_FLASH_DRIVE_SUPPORT) && !PINS_EXIST(USB_CS, USB_INTR) #error "USB_CS_PIN and USB_INTR_PIN are required for USB_FLASH_DRIVE_SUPPORT." #endif #if ENABLED(SD_FIRMWARE_UPDATE) && !defined(__AVR_ATmega2560__) #error "SD_FIRMWARE_UPDATE requires an ATmega2560-based (Arduino Mega) board." #endif #if ENABLED(GCODE_MACROS) && !WITHIN(GCODE_MACROS_SLOTS, 1, 10) #error "GCODE_MACROS_SLOTS must be a number from 1 to 10." #endif #if ENABLED(CUSTOM_USER_MENUS) #ifdef USER_GCODE_1 constexpr char _chr1 = USER_GCODE_1[strlen(USER_GCODE_1) - 1]; static_assert(_chr1 != '\n' && _chr1 != '\r', "USER_GCODE_1 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_2 constexpr char _chr2 = USER_GCODE_2[strlen(USER_GCODE_2) - 1]; static_assert(_chr2 != '\n' && _chr2 != '\r', "USER_GCODE_2 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_3 constexpr char _chr3 = USER_GCODE_3[strlen(USER_GCODE_3) - 1]; static_assert(_chr3 != '\n' && _chr3 != '\r', "USER_GCODE_3 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_4 constexpr char _chr4 = USER_GCODE_4[strlen(USER_GCODE_4) - 1]; static_assert(_chr4 != '\n' && _chr4 != '\r', "USER_GCODE_4 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_5 constexpr char _chr5 = USER_GCODE_5[strlen(USER_GCODE_5) - 1]; static_assert(_chr5 != '\n' && _chr5 != '\r', "USER_GCODE_5 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_6 constexpr char _chr6 = USER_GCODE_6[strlen(USER_GCODE_6) - 1]; static_assert(_chr6 != '\n' && _chr6 != '\r', "USER_GCODE_6 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_7 constexpr char _chr7 = USER_GCODE_7[strlen(USER_GCODE_7) - 1]; static_assert(_chr7 != '\n' && _chr7 != '\r', "USER_GCODE_7 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_8 constexpr char _chr8 = USER_GCODE_8[strlen(USER_GCODE_8) - 1]; static_assert(_chr8 != '\n' && _chr8 != '\r', "USER_GCODE_8 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_9 constexpr char _chr9 = USER_GCODE_9[strlen(USER_GCODE_9) - 1]; static_assert(_chr9 != '\n' && _chr9 != '\r', "USER_GCODE_9 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_10 constexpr char _chr10 = USER_GCODE_10[strlen(USER_GCODE_10) - 1]; static_assert(_chr10 != '\n' && _chr10 != '\r', "USER_GCODE_10 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_11 constexpr char _chr11 = USER_GCODE_11[strlen(USER_GCODE_11) - 1]; static_assert(_chr11 != '\n' && _chr11 != '\r', "USER_GCODE_11 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_12 constexpr char _chr12 = USER_GCODE_12[strlen(USER_GCODE_12) - 1]; static_assert(_chr12 != '\n' && _chr12 != '\r', "USER_GCODE_12 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_13 constexpr char _chr13 = USER_GCODE_13[strlen(USER_GCODE_13) - 1]; static_assert(_chr13 != '\n' && _chr13 != '\r', "USER_GCODE_13 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_14 constexpr char _chr14 = USER_GCODE_14[strlen(USER_GCODE_14) - 1]; static_assert(_chr14 != '\n' && _chr14 != '\r', "USER_GCODE_14 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_15 constexpr char _chr15 = USER_GCODE_15[strlen(USER_GCODE_15) - 1]; static_assert(_chr15 != '\n' && _chr15 != '\r', "USER_GCODE_15 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_16 constexpr char _chr16 = USER_GCODE_16[strlen(USER_GCODE_16) - 1]; static_assert(_chr16 != '\n' && _chr16 != '\r', "USER_GCODE_16 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_17 constexpr char _chr17 = USER_GCODE_17[strlen(USER_GCODE_17) - 1]; static_assert(_chr17 != '\n' && _chr17 != '\r', "USER_GCODE_17 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_18 constexpr char _chr18 = USER_GCODE_18[strlen(USER_GCODE_18) - 1]; static_assert(_chr18 != '\n' && _chr18 != '\r', "USER_GCODE_18 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_19 constexpr char _chr19 = USER_GCODE_19[strlen(USER_GCODE_19) - 1]; static_assert(_chr19 != '\n' && _chr19 != '\r', "USER_GCODE_19 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_20 constexpr char _chr20 = USER_GCODE_20[strlen(USER_GCODE_20) - 1]; static_assert(_chr20 != '\n' && _chr20 != '\r', "USER_GCODE_20 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_21 constexpr char _chr21 = USER_GCODE_21[strlen(USER_GCODE_21) - 1]; static_assert(_chr21 != '\n' && _chr21 != '\r', "USER_GCODE_21 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_22 constexpr char _chr22 = USER_GCODE_22[strlen(USER_GCODE_22) - 1]; static_assert(_chr22 != '\n' && _chr22 != '\r', "USER_GCODE_22 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_23 constexpr char _chr23 = USER_GCODE_23[strlen(USER_GCODE_23) - 1]; static_assert(_chr23 != '\n' && _chr23 != '\r', "USER_GCODE_23 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_24 constexpr char _chr24 = USER_GCODE_24[strlen(USER_GCODE_24) - 1]; static_assert(_chr24 != '\n' && _chr24 != '\r', "USER_GCODE_24 cannot have a newline at the end. Please remove it."); #endif #ifdef USER_GCODE_25 constexpr char _chr25 = USER_GCODE_25[strlen(USER_GCODE_25) - 1]; static_assert(_chr25 != '\n' && _chr25 != '\r', "USER_GCODE_25 cannot have a newline at the end. Please remove it."); #endif #endif #if ENABLED(BACKLASH_COMPENSATION) #ifndef BACKLASH_DISTANCE_MM #error "BACKLASH_COMPENSATION requires BACKLASH_DISTANCE_MM." #elif !defined(BACKLASH_CORRECTION) #error "BACKLASH_COMPENSATION requires BACKLASH_CORRECTION." #elif IS_CORE constexpr float backlash_arr[] = BACKLASH_DISTANCE_MM; static_assert(!backlash_arr[CORE_AXIS_1] && !backlash_arr[CORE_AXIS_2], "BACKLASH_COMPENSATION can only apply to " STRINGIFY(NORMAL_AXIS) " with your CORE system."); #endif #endif #if ENABLED(GRADIENT_MIX) && MIXING_VIRTUAL_TOOLS < 2 #error "GRADIENT_MIX requires 2 or more MIXING_VIRTUAL_TOOLS." #endif /** * Photo G-code requirements */ #if ENABLED(PHOTO_GCODE) #if (PIN_EXISTS(CHDK) + PIN_EXISTS(PHOTOGRAPH) + defined(PHOTO_SWITCH_POSITION)) > 1 #error "Please define only one of CHDK_PIN, PHOTOGRAPH_PIN, or PHOTO_SWITCH_POSITION." #elif defined(PHOTO_SWITCH_POSITION) && !defined(PHOTO_POSITION) #error "PHOTO_SWITCH_POSITION requires PHOTO_POSITION. Please update your Configuration_adv.h." #elif PIN_EXISTS(CHDK) && defined(CHDK_DELAY) #error "CHDK_DELAY has been replaced by PHOTO_SWITCH_MS. Please update your Configuration_adv.h." #elif PIN_EXISTS(CHDK) && !defined(PHOTO_SWITCH_MS) #error "PHOTO_SWITCH_MS is required with CHDK_PIN. Please update your Configuration_adv.h." #elif defined(PHOTO_RETRACT_MM) static_assert(PHOTO_RETRACT_MM + 0 >= 0, "PHOTO_RETRACT_MM must be >= 0."); #endif #endif /** * Prusa MMU2 requirements */ #if ENABLED(PRUSA_MMU2) #if EXTRUDERS != 5 #error "PRUSA_MMU2 requires EXTRUDERS = 5." #elif DISABLED(NOZZLE_PARK_FEATURE) #error "PRUSA_MMU2 requires NOZZLE_PARK_FEATURE. Enable it to continue." #elif EITHER(PRUSA_MMU2_S_MODE, MMU_EXTRUDER_SENSOR) && DISABLED(FILAMENT_RUNOUT_SENSOR) #error "PRUSA_MMU2_S_MODE or MMU_EXTRUDER_SENSOR requires FILAMENT_RUNOUT_SENSOR. Enable it to continue." #elif BOTH(PRUSA_MMU2_S_MODE, MMU_EXTRUDER_SENSOR) #error "Enable only one of PRUSA_MMU2_S_MODE or MMU_EXTRUDER_SENSOR." #elif DISABLED(ADVANCED_PAUSE_FEATURE) static_assert(nullptr == strstr(MMU2_FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with PRUSA_MMU2."); #endif #endif /** * Advanced PRINTCOUNTER settings */ #if ENABLED(PRINTCOUNTER) #if defined(SERVICE_INTERVAL_1) != defined(SERVICE_NAME_1) #error "Both SERVICE_NAME_1 and SERVICE_INTERVAL_1 are required." #elif defined(SERVICE_INTERVAL_2) != defined(SERVICE_NAME_2) #error "Both SERVICE_NAME_2 and SERVICE_INTERVAL_2 are required." #elif defined(SERVICE_INTERVAL_3) != defined(SERVICE_NAME_3) #error "Both SERVICE_NAME_3 and SERVICE_INTERVAL_3 are required." #endif #endif /** * Require soft endstops for certain setups */ #if !BOTH(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) #if ENABLED(DUAL_X_CARRIAGE) #error "DUAL_X_CARRIAGE requires both MIN_ and MAX_SOFTWARE_ENDSTOPS." #elif HAS_HOTEND_OFFSET #error "MIN_ and MAX_SOFTWARE_ENDSTOPS are both required with offset hotends." #endif #endif /** * Ensure this option is set intentionally */ #if ENABLED(PSU_CONTROL) #ifndef PSU_ACTIVE_HIGH #error "PSU_CONTROL requires PSU_ACTIVE_HIGH to be defined as 'true' or 'false'." #elif !PIN_EXISTS(PS_ON) #error "PSU_CONTROL requires PS_ON_PIN." #endif #elif ENABLED(AUTO_POWER_CONTROL) #error "AUTO_POWER_CONTROL requires PSU_CONTROL." #endif #if HAS_CUTTER #ifndef CUTTER_POWER_UNIT #error "CUTTER_POWER_UNIT is required with a spindle or laser. Please update your Configuration_adv.h." #elif !CUTTER_UNIT_IS(PWM255) && !CUTTER_UNIT_IS(PERCENT) && !CUTTER_UNIT_IS(RPM) #error "CUTTER_POWER_UNIT must be PWM255, PERCENT, or RPM. Please update your Configuration_adv.h." #endif #if ENABLED(LASER_POWER_INLINE) #if ENABLED(SPINDLE_CHANGE_DIR) #error "SPINDLE_CHANGE_DIR and LASER_POWER_INLINE are incompatible." #elif ENABLED(LASER_MOVE_G0_OFF) && DISABLED(LASER_MOVE_POWER) #error "LASER_MOVE_G0_OFF requires LASER_MOVE_POWER. Please update your Configuration_adv.h." #endif #if ENABLED(LASER_POWER_INLINE_TRAPEZOID) #if DISABLED(SPINDLE_LASER_PWM) #error "LASER_POWER_INLINE_TRAPEZOID requires SPINDLE_LASER_PWM to function." #elif ENABLED(S_CURVE_ACCELERATION) //#ifndef LASER_POWER_INLINE_S_CURVE_ACCELERATION_WARN // #define LASER_POWER_INLINE_S_CURVE_ACCELERATION_WARN // #warning "Combining LASER_POWER_INLINE_TRAPEZOID with S_CURVE_ACCELERATION may result in unintended behavior." //#endif #endif #endif #if ENABLED(LASER_POWER_INLINE_INVERT) //#ifndef LASER_POWER_INLINE_INVERT_WARN // #define LASER_POWER_INLINE_INVERT_WARN // #warning "Enabling LASER_POWER_INLINE_INVERT means that `M5` won't kill the laser immediately; use `M5 I` instead." //#endif #endif #else #if SPINDLE_LASER_POWERUP_DELAY < 1 #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0." #elif SPINDLE_LASER_POWERDOWN_DELAY < 1 #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0." #elif ENABLED(LASER_MOVE_POWER) #error "LASER_MOVE_POWER requires LASER_POWER_INLINE." #elif ANY(LASER_POWER_INLINE_TRAPEZOID, LASER_POWER_INLINE_INVERT, LASER_MOVE_G0_OFF, LASER_MOVE_POWER) #error "Enabled an inline laser feature without inline laser power being enabled." #endif #endif #define _PIN_CONFLICT(P) (PIN_EXISTS(P) && P##_PIN == SPINDLE_LASER_PWM_PIN) #if BOTH(SPINDLE_FEATURE, LASER_FEATURE) #error "Enable only one of SPINDLE_FEATURE or LASER_FEATURE." #elif !PIN_EXISTS(SPINDLE_LASER_ENA) #error "(SPINDLE|LASER)_FEATURE requires SPINDLE_LASER_ENA_PIN." #elif ENABLED(SPINDLE_CHANGE_DIR) && !PIN_EXISTS(SPINDLE_DIR) #error "SPINDLE_DIR_PIN is required for SPINDLE_CHANGE_DIR." #elif ENABLED(SPINDLE_LASER_PWM) #if !defined(SPINDLE_LASER_PWM_PIN) || SPINDLE_LASER_PWM_PIN < 0 #error "SPINDLE_LASER_PWM_PIN is required for SPINDLE_LASER_PWM." #elif !_TEST_PWM(SPINDLE_LASER_PWM_PIN) #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin." #elif !defined(SPINDLE_LASER_PWM_INVERT) #error "SPINDLE_LASER_PWM_INVERT is required for (SPINDLE|LASER)_FEATURE." #elif !(defined(SPEED_POWER_INTERCEPT) && defined(SPEED_POWER_MIN) && defined(SPEED_POWER_MAX) && defined(SPEED_POWER_STARTUP)) #error "SPINDLE_LASER_PWM equation constant(s) missing." #elif _PIN_CONFLICT(X_MIN) #error "SPINDLE_LASER_PWM pin conflicts with X_MIN_PIN." #elif _PIN_CONFLICT(X_MAX) #error "SPINDLE_LASER_PWM pin conflicts with X_MAX_PIN." #elif _PIN_CONFLICT(Z_STEP) #error "SPINDLE_LASER_PWM pin conflicts with Z_STEP_PIN." #elif _PIN_CONFLICT(CASE_LIGHT) #error "SPINDLE_LASER_PWM_PIN conflicts with CASE_LIGHT_PIN." #elif _PIN_CONFLICT(E0_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E0_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E1_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E1_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E2_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E2_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E3_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E3_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E4_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E4_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E5_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E5_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E6_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E6_AUTO_FAN_PIN." #elif _PIN_CONFLICT(E7_AUTO_FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with E7_AUTO_FAN_PIN." #elif _PIN_CONFLICT(FAN) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN_PIN." #elif _PIN_CONFLICT(FAN1) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN1_PIN." #elif _PIN_CONFLICT(FAN2) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN2_PIN." #elif _PIN_CONFLICT(FAN3) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN3_PIN." #elif _PIN_CONFLICT(FAN4) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN4_PIN." #elif _PIN_CONFLICT(FAN5) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN5_PIN." #elif _PIN_CONFLICT(FAN6) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN6_PIN." #elif _PIN_CONFLICT(FAN7) #error "SPINDLE_LASER_PWM_PIN conflicts with FAN7_PIN." #elif _PIN_CONFLICT(CONTROLLERFAN) #error "SPINDLE_LASER_PWM_PIN conflicts with CONTROLLERFAN_PIN." #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_XY) #error "SPINDLE_LASER_PWM_PIN conflicts with MOTOR_CURRENT_PWM_XY." #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_Z) #error "SPINDLE_LASER_PWM_PIN conflicts with MOTOR_CURRENT_PWM_Z." #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_E) #error "SPINDLE_LASER_PWM_PIN conflicts with MOTOR_CURRENT_PWM_E." #endif #endif #undef _PIN_CONFLICT #endif #if !HAS_GRAPHICAL_LCD #if ENABLED(PRINT_PROGRESS_SHOW_DECIMALS) #error "PRINT_PROGRESS_SHOW_DECIMALS currently requires a Graphical LCD." #elif ENABLED(SHOW_REMAINING_TIME) #error "SHOW_REMAINING_TIME currently requires a Graphical LCD." #endif #endif #if HAS_ADC_BUTTONS && defined(ADC_BUTTON_DEBOUNCE_DELAY) && ADC_BUTTON_DEBOUNCE_DELAY < 16 #error "ADC_BUTTON_DEBOUNCE_DELAY must be greater than 16." #endif /** * Check to make sure MONITOR_DRIVER_STATUS isn't enabled * on boards where TMC drivers share the SPI bus with SD. */ #if HAS_TMC_SPI && ALL(MONITOR_DRIVER_STATUS, SDSUPPORT, USES_SHARED_SPI) #error "MONITOR_DRIVER_STATUS and SDSUPPORT cannot be used together on boards with shared SPI." #endif // G60/G61 Position Save #if SAVED_POSITIONS > 256 #error "SAVED_POSITIONS must be an integer from 0 to 256." #endif /** * Stepper Chunk support */ #if BOTH(DIRECT_STEPPING, LIN_ADVANCE) #error "DIRECT_STEPPING is incompatible with LIN_ADVANCE. Enable in external planner if possible." #endif /** * Touch Buttons */ #if ENABLED(TOUCH_SCREEN) #ifndef XPT2046_X_CALIBRATION #error "XPT2046_X_CALIBRATION must be defined with TOUCH_SCREEN." #endif #ifndef XPT2046_Y_CALIBRATION #error "XPT2046_Y_CALIBRATION must be defined with TOUCH_SCREEN." #endif #ifndef XPT2046_X_OFFSET #error "XPT2046_X_OFFSET must be defined with TOUCH_SCREEN." #endif #ifndef XPT2046_Y_OFFSET #error "XPT2046_Y_OFFSET must be defined with TOUCH_SCREEN." #endif #endif /** * Sanity check for WIFI */ #if EITHER(ESP3D_WIFISUPPORT, WIFISUPPORT) && DISABLED(ARDUINO_ARCH_ESP32) #error "ESP3D_WIFISUPPORT or WIFISUPPORT requires an ESP32 controller." #endif // Misc. Cleanup #undef _TEST_PWM