/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#include "../../../../inc/MarlinConfigPre.h"

#if HAS_TFT_LVGL_UI

#include "tft_lvgl_configuration.h"

#if ENABLED(USE_WIFI_FUNCTION)

#include "draw_ui.h"
#include "wifiSerial.h"

#include <libmaple/libmaple.h>
#include <libmaple/gpio.h>
#include <libmaple/timer.h>
#include <libmaple/usart.h>
#include <libmaple/ring_buffer.h>

#include "../../../../MarlinCore.h"

DEFINE_WFSERIAL(WifiSerial1, 1);

WifiSerial::WifiSerial(usart_dev *usart_device, uint8 tx_pin, uint8 rx_pin) {
  this->usart_device = usart_device;
  this->tx_pin = tx_pin;
  this->rx_pin = rx_pin;
}

/**
 * Set up / tear down
 */
#if STM32_MCU_SERIES == STM32_SERIES_F1
  /* F1 MCUs have no GPIO_AFR[HL], so turn off PWM if there's a conflict
   * on this GPIO bit. */
  static void disable_timer_if_necessary(timer_dev *dev, uint8 ch) {
    if (dev != nullptr) timer_set_mode(dev, ch, TIMER_DISABLED);
  }
#elif STM32_MCU_SERIES == STM32_SERIES_F2 || STM32_MCU_SERIES == STM32_SERIES_F4
  #define disable_timer_if_necessary(dev, ch) ((void)0)
#else
  #warning "Unsupported STM32 series; timer conflicts are possible"
#endif

void WifiSerial::begin(uint32 baud) { begin(baud, SERIAL_8N1); }

/**
 * Roger Clark.
 * Note. The config parameter is not currently used. This is a work in progress.
 * Code needs to be written to set the config of the hardware serial control register in question.
 */

void WifiSerial::begin(uint32 baud, uint8_t config) {
  //ASSERT(baud <= this->usart_device->max_baud); // Roger Clark. Assert doesn't do anything useful, we may as well save the space in flash and ram etc

  if (baud > this->usart_device->max_baud) return;

  const stm32_pin_info *txi = &PIN_MAP[this->tx_pin],
                       *rxi = &PIN_MAP[this->rx_pin];

  disable_timer_if_necessary(txi->timer_device, txi->timer_channel);

  usart_init(this->usart_device);

  // Reinitialize the receive buffer, mks_esp8266 fixed data frame length is 1k bytes
  rb_init(this->usart_device->rb, WIFI_RX_BUF_SIZE, wifiRxBuf);

  usart_config_gpios_async(this->usart_device,
                           rxi->gpio_device, rxi->gpio_bit,
                           txi->gpio_device, txi->gpio_bit,
                           config);
  usart_set_baud_rate(this->usart_device, USART_USE_PCLK, baud);
  usart_enable(this->usart_device);
}

void WifiSerial::end(void) {
  usart_disable(this->usart_device);
}

int WifiSerial::available(void) {
  return usart_data_available(this->usart_device);
}

//
// I/O
//

int WifiSerial::read(void) {
  if (usart_data_available(usart_device) <= 0) return -1;
  return usart_getc(usart_device);
}

int WifiSerial::write(unsigned char ch) {
  usart_putc(this->usart_device, ch);
  return 1;
}

int WifiSerial::wifi_rb_is_full(void) {
  return rb_is_full(this->usart_device->rb);
}

#endif // USE_WIFI_FUNCTION
#endif // HAS_TFT_LVGL_UI