cf792fd8d8
Update configurations to use RAMPS 1.4
9 years ago
13ef12ad3f
Fix power calculations
As suggested by @max-pau in #3073 - #3074
9 years ago
5cba0210f2
Small patch to Z_SAFE_HOMING comment
9 years ago
6165fd41a5
Fix Hephestos 2 and other configs
9 years ago
143ad74db7
Update PROBE_OFFSET_FROM_EXTRUDER comment section in all example config
files.
9 years ago
772460a7b8
Various minor spelling corrections
Redo of #2939 rebased against RCBugFix
9 years ago
615bec2329
Activate warning about possible reduced accuracy by default
Renamed `WARN_REDUCED_ACCURACY` to `DISABLE_REDUCED_ACCURACY_WARNING`
Changed the condition for blinking from
```
#if ENABLED(WARN_REDUCED_ACCURACY)
```
to
```
#if DISABLED(DISABLE_REDUCED_ACCURACY_WARNING)
```
9 years ago
4b02f33e69
Distribute config-changes to the other configurations
9 years ago
68eae2b5a8
added kossel xl example configuration
9 years ago
1093c780c8
Remove obsolete STEPS_MM_E setting
9 years ago
c2e5c6c12c
Nest Manual Bed Leveling options
This formalizes the dependency of MANUAL_BED_LEVELING on
MESH_BED_LEVELING
9 years ago
fbfbc5e330
Enable USE_WATCHDOG by default
9 years ago
b19b272172
Update configurations with SPI_SPEED
- Include aligned comment about new SDSUPPORT behavior
9 years ago
159ff94afd
Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977
9 years ago
b58083b0fa
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
1b7c443628
Adding SDULTRASLOW variable.
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
59d345a3dd
Update Configuration.h
9 years ago
b8f0c8a4c7
Update Configuration.h
9 years ago
df0d599c79
Update Configuration.h
9 years ago
a366697649
Update Configuration.h
9 years ago
1403b9acc0
Update Configuration_adv.h
9 years ago
5cf1c38ea1
Update Configuration_adv.h
9 years ago
04ab61bf40
Update Configuration_adv.h
9 years ago
39c62fbd6f
Update Configuration_adv.h
9 years ago
2c9e0415c7
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
e6cc232184
Adding SDULTRASLOW variable.
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
0b429461d5
Back port Cosmetic changes
9 years ago
0cebe85e65
Clean up spacing and duplicate entries
• Removing trailing whitespace
• Adjusting indention for better readability
• Removing duplicated entries
9 years ago
e7b40bbe98
Change link to U8glib source
9 years ago
6bfcb74c25
The probe stowing coordinates have changed
9 years ago
c956b52c4a
Babystep Multiplier
Analog to https://github.com/MarlinFirmware/MarlinDev/pull/250 by
@RicardoGA
Restore the Babystep Multiplicator functionality and now it's available
for X/Y/Z
9 years ago
33addc52a1
Suppress Z_MIN_PROBE_REPEATABILITY_TEST for DELTA and SCARA configurations (PR#2747)
For now Z_MIN_PROBE_REPEATABILITY_TEST is not possible for DELTA or SCARA
configurations.
This PR comments the feature out, where it is commented in by default.
9 years ago
9b23490f01
Clean up spacing in configs
9 years ago
0ad25c6665
Hint for changed behaviour of SDSUPPORT
9 years ago
e01f5e1ef7
Cleanup
9 years ago
5e36b64635
SDEXTRASLOW for some SD card readers (PR#176)
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
9 years ago
db27e67580
Apply PID_ADD_EXTRUSION_RATE to extras
9 years ago
8b3d63c423
Unify Delta XYZ homing rates
As noted in #130 allen key probe stow rate is based on homing rates,
but homing rates were left out of most delta configs. This unifies the
XYZ homing rates and applies the unified rates to allen key movements.
9 years ago
7c72b57313
Unify manual feedrate and Fix LCD MANUAL_FEEDRATE (PR#128)
As noted by @o-lampe at https://github.com/MarlinFirmware/MarlinDev/issues/114#issuecomment-136757614 the `MANUAL_FEEDRATE` for Delta Z should be the same as XY.
9 years ago
a39fadf876
Update kossel-pro example config (again?)
9 years ago
28599c51c7
Wrap Dual Y options in a conditional
9 years ago
11a065c0ca
Remove Z2 pins overrides from Configuration_adv.h
9 years ago
8347a9d6e4
Fix HOMING_BUMP_DIVISOR for deltas configuration
* Re-bump speed divisor should be the same for delta printer.
9 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)
reads better than
9 years ago
9897a9147c
Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
9 years ago
a7822e3ff7
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
* Fix a couple of renames omission and macro expansion errors.
9 years ago
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
b227d8c128
Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
9 years ago
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
9 years ago
Scott Lahteine
jbrazio
AnHardt
Marc Urben
Ruwan J Egoda Gamage
esenapaj
Richard Wackerbarth
KiteLab
Mike Cochrane
Christian Lefrançois