e2d703377a
Enable EEPROM by default for 5DPrint D8 Controller Board in example configuration
11 years ago
2715f6ddbf
Fix for reading microstepping resolution
11 years ago
39e9b133f3
Add example configuration for Makibox printer, which uses the 5DPrint D8 Driver Board
11 years ago
da6b536182
Add 5DPrint D8 Driver Board info and temperature table for Makibox hot bed
11 years ago
3a8e36f19e
Add Digipot config for 5DPrint D8 Driver Board
11 years ago
eea3ba5588
Fix for stepper microstepping
11 years ago
1cbcbb0971
Add makibox machine information
11 years ago
2fa514e88a
Add port for 5DPrint D8 Driver board
11 years ago
27d544ac25
Speed up QUICK_HOME feedrate for diagonal move
Speed up the diagonal move while still keeping each individual axis at
or below its homing feedrate.
11 years ago
e5b70237c7
Added new language (Basque-Euskera)
Added:
* new language (Basque-Euskera)
* some minor corrections for Spanish
* added 2 new constants for every language (required for a minor change
I am preparing to ultralcd.cpp)
11 years ago
ed6f4a71c5
fix wrong temptable index
11 years ago
3161740df9
This table is made for thermistor 3950 (can be found on ebay for cheap)
it's caracteristics are :
R25℃ ;100KΩ±1%
B Value(R25/50℃)：3990K 1%
Dissipation Factor(mW/℃)：1.1~1.6 In still Air
Thermal Time Constant(S)：10~17 In Still Air
Operating temperature range： (-50~+260°C)
Dimension： 1.8mm Dia X4.1mm
Lead Length ：30mm
This table was found on the following blogs:
http://cae2100.wordpress.com/2014/03/08/beta3950-thermistor-table-for-marlin/
and
http://microfabricator.com/articles/view/id/531ad7e59aad9d3131000000/beta-3950-thermistor-table-for-marlin
11 years ago
27a7cf9fcf
use existing strings
11 years ago
d3f305332a
Allowable range now includes default value
11 years ago
b0aeac117f
Adjustable Z probe offset, via custom M-code
11 years ago
dfb98101e4
Change CONTROLLERFAN_PIN for board 35 to -1, as it would conflict with board's 33 extruder pin, causing burnout (it's the same board, just different number of fans/extruders, therefore should be pin-compatible)
11 years ago
8759508319
fix bug for dual extruders not working
some guy find that marlin not working good for dual extruders delta .
when type T0 or T1 to active extruder and E0 or E1 move causing XYZ
motion . so i locales the bugs and fix it , I have dry run the fix.
11 years ago
a65564eef6
fix bug in M200 with multiple extruders
11 years ago
aeaf9b9312
fix bug in M200 with multiple extruders
11 years ago
b0093a1513
thermistortables.h: Add comments that table 60 uses beta=3950.
11 years ago
a3530d1141
Update language.h
Updated to latest version.
11 years ago
990e770e15
Update language.h
Added catalan language
11 years ago
c8cdd1fc6f
Bugfixes for language option 6 (russian)
11 years ago
7395dafc1e
semantic changes in language.h
11 years ago
fad2a60ce6
Corrections for preheat extension in language.h
11 years ago
eecda434fb
Sanguinololu servo pins set default disabled
11 years ago
944ced87c5
Extended Preheat options
Preheat LCD menus base on code by D-Base
11 years ago
06709ad60e
Added servo pin assignments to Sanguinololu
11 years ago
3906f27c46
Individual extruder flow rate
Extension of M221, Tune menu
11 years ago
aab61e63c3
FWRETRACT in mm/s
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.
I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
11 years ago
6cd85e6008
Add support for disabling encoder control for feedrate multiplier
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
11 years ago
09af1b90b8
Added CHDK support
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
11 years ago
765b2da3d4
Added CHDK support
Added so M240 can be used to trigger CHDK instead of sending an IR signal, see more about CHDK here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
11 years ago
881e348eed
Update Configuration_adv.h
Increase Z_HOME_RETRACT_MM to 2mm default to avoid end stop not switching during retract.
11 years ago
15d1b8d719
Fixed finnish translation
- Fixed Few finnish transalations
- Removed duplicate contrast define
11 years ago
fcd8524b6e
Only increase EEPROM version for DELTA printers.
11 years ago
8c4377dd63
temperature.cpp: Fix PID_DEBUG compile error.
11 years ago
fdce91192e
Various typo fixes - only in comments, no code changes.
11 years ago
d819c55395
Various typo fixes - only in comments, no code changes.
11 years ago
77df0d689a
autretract fix
I made these changes previously, but I can’t find the commit now. This
reapplies the changes to get auto retract working again.
Conflicts:
Marlin/Configuration_adv.h
Marlin/Marlin_main.cpp
11 years ago
aee63afccd
Clarify which PID values to enter
Users can be confused as to which values to enter after a PID tune. Updating the message to help clarity it.
New message: "PID Autotune finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"
Old message: "PID Autotune finished! Put the Kp, Ki and Kd constants into Configuration.h"
11 years ago
99f6326544
Remove unnecessary dependency on time.h from qr_solve.cpp
Fixed compiler errors on Ubuntu using arduino-core
11 years ago
ea669cb504
Fix some extra and some missing tabs, to make the file consistent.
11 years ago
b46a1b6360
Update the menu plan document with the current menu as per ultralcd.cpp.
11 years ago
174b8d99d5
Simplify 3-point probing using new code only
11 years ago
3b718b816c
better documentation
11 years ago
34fd59c370
ABL at any points
11 years ago
f308a8af91
update comment
11 years ago
357e31270a
Prevent G29 without first homing in X and Y
If position is unknown, then G29 can be dangerous.
11 years ago
d2d7d186b5
Use descriptive constants, more
11 years ago
Cameron Lai
whosawhatsis
koldo artola
Nutz95
Gabe Rosenhouse
nothinman
Tim
David Forrest
pixatintes
pixatintes
Dim3nsioneer
Dim3nsioneer
Ralf Schultz
Matthew Schick
blddk
paciotti
Tommi Lamberg
Erik van der Zalm
Cylindric
RoyOnWheels