c2e5c6c12c
Nest Manual Bed Leveling options
This formalizes the dependency of MANUAL_BED_LEVELING on
MESH_BED_LEVELING
9 years ago
042a6a0a37
Extend existing MESH_BED_LEVELING test
9 years ago
08b3147791
sanity check for MANUAL_BED_LEVELING
9 years ago
438a87eba8
Sanity check deprecated SDSLOW, SDEXTRASLOW
9 years ago
b19b272172
Update configurations with SPI_SPEED
- Include aligned comment about new SDSUPPORT behavior
9 years ago
b81d3b83cf
Drop the experimental Configurator
Development moved to https://github.com/thinkyhead/MarlinConfigurator
9 years ago
be691b51f1
Remove references to marlinfirmware.org
The domain is gone and doesn’t redirect, so for now show no URL on the boot screen.
9 years ago
b83e472bd3
Rename fpos_t to avoid libc conflict
9 years ago
68457ee903
For Dual Y/Z use the next available extruder pins
9 years ago
711e5db19a
Tweak comment in process_next_command
9 years ago
400e9329be
Allow spaces after a code letter
9 years ago
cdcb80f3c5
Allow no-space after initial command
Addresses issue #2715
9 years ago
6f473f7fc6
Repair N in ADVANCED_OK
Send the correct line number.
If no N was in the command - non't send an N.
9 years ago
efbd705eda
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
to avoid senting two "ok"s for a single g-code.
Doing the same for M105 would break the input filters of the hosts.
For M105 the other "ok" is omitted.
9 years ago
159ff94afd
Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977
9 years ago
1270fbfd38
Using SET_INPUT instead of pinMode
9 years ago
b58083b0fa
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
1833049b8a
reusing millis()
9 years ago
1b7c443628
Adding SDULTRASLOW variable.
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
6f9e9c0e4f
Cleaning up, getting rid of the fake encoder count variable.
9 years ago
becbfe1065
Fixing Rigidbot LCD Panel Support
9 years ago
4882a7eded
more suitable display format for delta printer
9 years ago
59d345a3dd
Update Configuration.h
9 years ago
b8f0c8a4c7
Update Configuration.h
9 years ago
df0d599c79
Update Configuration.h
9 years ago
a366697649
Update Configuration.h
9 years ago
7c94c83765
Repair formula mangled by PR#1319 in Jan 2015
9 years ago
2932602643
Update stepper.cpp
Forgot Z2_MIN_PIN
9 years ago
06555febdd
Using SET_INPUT instead of pinMode
9 years ago
8d2aa2368d
Update Configuration_adv.h
9 years ago
0de5fcad0a
Update Configuration_adv.h
9 years ago
1403b9acc0
Update Configuration_adv.h
9 years ago
5cf1c38ea1
Update Configuration_adv.h
9 years ago
04ab61bf40
Update Configuration_adv.h
9 years ago
39c62fbd6f
Update Configuration_adv.h
9 years ago
efcb769003
Update Configuration_adv.h
9 years ago
992fbb831d
Update Configuration_adv.h
9 years ago
5ee6fe6385
Update Configuration_adv.h
9 years ago
056daf00fc
Update Configuration_adv.h
9 years ago
71aafb79a0
Update Configuration_adv.h
9 years ago
2c9e0415c7
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
a64bcd53e9
reusing millis()
9 years ago
e6cc232184
Adding SDULTRASLOW variable.
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
83c4131ba3
Cleaning up, getting rid of the fake encoder count variable.
9 years ago
5eeea2f611
Fixing Rigidbot LCD Panel Support
9 years ago
f6950acb8e
Residual unused variable — Backport
9 years ago
7a670e3911
Improve planner & stepper PR #263
9 years ago
58658c9279
Call the probe pin a probe pin and not a min endstop
9 years ago
0fa3bac8ee
If unused, just don’t define it.
9 years ago
3b2973da6a
Prepare Ramps for user redefinition
9 years ago
Scott Lahteine
esenapaj
AnHardt
Ruwan J Egoda Gamage
Richard Wackerbarth
Naruto-kyun