2733 Commits (bdf778bec22cba70a47d3d64330a87af872d36cb)

Author SHA1 Message Date
Ed Boston 08968c29bb Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples 10 years ago
Ed Boston fed18bcc20 Removed SDSLOW for ELB_FULL_GRAPHIC_CONTROLLER 10 years ago
Ed Boston b94a0e1501 Added ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED 10 years ago
Ed Boston bc205c76a3 SDCARDDETECTINVERTED problems 10 years ago
MagoKimbra 4db8d2def4 Moved MSG_DEBUG in language.h 10 years ago
AnHardt b7e9ba7591 Back to 1.0.3 dev - for now 10 years ago
AnHardt b1404a0743 fix thermal protection state machine target temp. V2 10 years ago
AnHardt 17b0ec84ed Fix out_of_range_error() 10 years ago
wurstnase e7e964432b consistency name for multiplier 10 years ago
AnHardt 0d9d21d15f Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again. 10 years ago
MagoKimbra 76306f9073 Insert Debug DRYRUN Repetier Host compatible 10 years ago
MagoKimbra 881146bc22 Fix problem Width Cura 10 years ago
Alexey Shvetsov a8670b66a7 Update ru translation 10 years ago
fmalpartida 93da52d011 Added support for OLED SSD1306 I2C based LCDs. 10 years ago
wurstnase 0f3f7d6835 clean up double endstops 10 years ago
Scott Lahteine be5236e839 Reduce setTargetedHotend by removing the switch 10 years ago
Scott Lahteine 06f401e7e5 Redo "invalid extruder" to save 264 bytes 10 years ago
Scott Lahteine 9beed830eb Drop commented code_is_good lines 10 years ago
Scott Lahteine 068d4a1eb2 Ignore unknown commands if they start with G, M, or T 10 years ago
Scott Lahteine 0564625757 Update M33 for new gcode parser 10 years ago
AnHardt f18f689c01 Replace MSG_F? with MSG_N? 10 years ago
AnHardt af7e3f5076 Print active extruder with M105 for MAX6675 10 years ago
Jonathan Bastien-Filiatrault d46d9d998e Add maximum bed integral term in example configurations. 10 years ago
Jonathan Bastien-Filiatrault e86f2342c0 Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX. 10 years ago
AnHardt f0523b5816 Initialize the display earlier 10 years ago
Scott Lahteine 790c697c19 Fix DEGREES macro 10 years ago
Scott Lahteine 03d5709b09 M110 is a known command 10 years ago
Scott Lahteine d76a01194d Slight size reduction by adding idle() 10 years ago
Richard Wackerbarth 2deb5a8ac5 Temporary Hack 10 years ago
Richard Wackerbarth b5743d6927 Use SOURCE_CODE_URL rather than FIRMWARE_URL 10 years ago
Richard Wackerbarth 5ea139fd79 Revised Versioning mechanism 10 years ago
AnHardt da246f5cb1 Activate BED_MINTEMP error. 10 years ago
AnHardt 959da98d8e Call kill() only once when triggered by a temperature error 10 years ago
Scott Lahteine 68f6f149d0 Reduce code size with out_of_range_error function 10 years ago
wurstnase 94120740d8 faster compare 10 years ago
Scott Lahteine b55f8718c3 Indent G90/G91, G92 10 years ago
Scott Lahteine b0d520b109 Indent G30, G31/G32 10 years ago
Scott Lahteine ffe27a6225 Indent G29 10 years ago
Scott Lahteine 86083badc2 Indent G4, G10/G11, G28 10 years ago
Scott Lahteine 47d7a9cb5e Indent G2/G3 10 years ago
Scott Lahteine 350f239d84 Indent G0/G1 10 years ago
Scott Lahteine 672b0c1fd3 Cleanup pins in RAMPS_13_EFB boards 10 years ago
Scott Lahteine 15a2351675 No need for +1 on initial seen_pointer 10 years ago
Scott Lahteine 550dd87b2a Set seen_pointer before calling code_value 10 years ago
Scott Lahteine 063881b5bd Fix a couple of doubled semicolons 10 years ago
AnHardt 0c0ace2a04 Remove start_watching_heater() fom M104 and M109 10 years ago
Scott Lahteine 00716d0ca0 Small start_watching_heater adjustment 10 years ago
Scott Lahteine bde9c70d42 Suppress the line mismatch error after M303 10 years ago
wurstnase ff98b8632b new endstop bits 10 years ago
AnHardt 9b0fa9c309 Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS 10 years ago