- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
- Add “Level Bed” menu item for auto bed leveling
- Hide the option if homing has not been done yet
- Arrange the Prepare submenu more logically (?)
- Add documentation comments, some white-space
- Apply some coding standards here and there
- Move old encoder multiplier debug option to `ultralcd.cpp`
This addresses comments in #1956 and #1079. In particular, this is useful
when both endstops are stationary on a CoreXY system, and the Y axis needs
to be homed before the X so the flags are aligned.
With these changes the output of `M503 S0` is all you need to restore
the EEPROM. Building on this it is straightforward to save and restore
the EEPROM state using the SD card or external GCode file.
- Added `M145` to set “heatup states” for the LCD menu
- Added `M420` to toggle Mesh Bed Leveling
- Added `M421` to set a single Mesh coordinate
- Extended `Config_PrintSettings` with added M codes
- Cleaned up some comments here and there
- Add `Conditionals.h` with calculated configuration values
- Add `SanityCheck.h` with checks for configuration errors
- Remove equivalent code from all configurations
- Move error checks from some sources to `SanityCheck.h` also
- Fix initialization of count_direction in stepper.cpp
# Add: Example Configuration for Vellemann K8200 - based on new
BOARD_K8200 #1391
* K8200: new folder in example_configurations for Vellemann K8200 (3Drag
clone - should work with 3Drag http://reprap.org/wiki/3drag, too. Please
report)
* K8200/Configuration.h/Configuration_adv.h: updated manually with
parameters form genuine Vellemann Firmware "firmware_k8200_marlinv2"
based on the recent development branch
I tested the changes on my K8200 with 20x4-LCD and Arduino 1.0.5 for
Windows (SD library added to IDE manually) - everything works well
Small changes (and formatting to confuse the diff’er) which first
allows DOGLCD and LCD_PROGRESS_BAR to be enabled in tandem, then a
#warning (rather than error) that the extra progress bar / message
options don’t apply to graphical displays at this time. This leaves
open perhaps combining the progress bar and message area in some future
(or forked custom) graphical LCD display arrangement (at which time the
relevant variables may be moved into ultralcd.cpp with externs in
ultralcd.h). I also added a conditional error that the progress bar and
the filament display may not work well together.
- Fixed issue when BAL area probing is shorter than it should be for
grid probing
- Warning when BAL activated with Delta Kinematics
- Fix XY_TRAVEL_SPEED when homing Z axis
Tosh stepper drivers need to be driven slower, so the stepper code
was interleaved to separate the pin HIGH from the pin LOW. This adds
enough instructions to make it work, without needing nops.
# The first commit's message is:
SD Card Alpha Sorting
First iteration of alphabetical sorting for SD cards, both
slow+efficient and fast+rammy. Option for folders to sort first, last,
or not at all.
# This is the 2nd commit message:
Expand on More RAM concept, address minor bugs
# This is the 3rd commit message:
Improvements, more SORT_USES_MORE_RAM
With this option, always keeps the dir in RAM, doubling as a cache for
getfilename. A board with only 8K of SRAM is cutting it very close.
# This is the 4th commit message:
Completed SORT_USES_MORE_RAM implementation
For the MORE_RAM option we need to buffer both the short and long
names, even though long names are sometimes redundant. Worst case, all
the names are max length. We can save some RAM by not storing these. We
could save more RAM by only storing the visible part of the long name.
FW retraction is extended onto swap retraction invoked by 'G10 S1'.
Bookkeeping of the retract state of all extruders allows for having one
extruder fw standard retracted while another extruder is swap retracted.
An LCD menu item for the swap retract and recover length was added.
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.
I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
if you try to enable Z_DUAL_STEPPER_DRIVERS the error "You cannot have dual drivers for both Y and Z" shows even if you don't have defined Y_DUAL_STEPPER_DRIVERS and don't let you compile the firmware
to solve this problem i change this line:
#ifdef Z_DUAL_STEPPER_DRIVERS && Y_DUAL_STEPPER_DRIVERS
to:
#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
now the error only show if you define both Z_DUAL_STEPPER_DRIVERS and Y_DUAL_STEPPER_DRIVERS
Scott Lahteine
Wurstnase
Steve Kelly
alexborro
AnHardt
CONSULitAS
Bo Herrmannsen
Dim3nsioneer
MyMakibox
whosawhatsis
Matthew Schick
blddk
paciotti
Mark Hanford
Jim Morris
RicardoGA