Tosh stepper drivers need to be driven slower, so the stepper code
was interleaved to separate the pin HIGH from the pin LOW. This adds
enough instructions to make it work, without needing nops.
# The first commit's message is:
SD Card Alpha Sorting
First iteration of alphabetical sorting for SD cards, both
slow+efficient and fast+rammy. Option for folders to sort first, last,
or not at all.
# This is the 2nd commit message:
Expand on More RAM concept, address minor bugs
# This is the 3rd commit message:
Improvements, more SORT_USES_MORE_RAM
With this option, always keeps the dir in RAM, doubling as a cache for
getfilename. A board with only 8K of SRAM is cutting it very close.
# This is the 4th commit message:
Completed SORT_USES_MORE_RAM implementation
For the MORE_RAM option we need to buffer both the short and long
names, even though long names are sometimes redundant. Worst case, all
the names are max length. We can save some RAM by not storing these. We
could save more RAM by only storing the visible part of the long name.
FW retraction is extended onto swap retraction invoked by 'G10 S1'.
Bookkeeping of the retract state of all extruders allows for having one
extruder fw standard retracted while another extruder is swap retracted.
An LCD menu item for the swap retract and recover length was added.
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.
I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
if you try to enable Z_DUAL_STEPPER_DRIVERS the error "You cannot have dual drivers for both Y and Z" shows even if you don't have defined Y_DUAL_STEPPER_DRIVERS and don't let you compile the firmware
to solve this problem i change this line:
#ifdef Z_DUAL_STEPPER_DRIVERS && Y_DUAL_STEPPER_DRIVERS
to:
#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
now the error only show if you define both Z_DUAL_STEPPER_DRIVERS and Y_DUAL_STEPPER_DRIVERS
If "SHOW_TEMP_ADC_VALUES" is defined in Configuration_adv.h, the M105
command will present, after tradicional temperatures, the ADC value read
from temp sensors. This is great for adjusting thermistor tables with
thermocouple.
From Pronterface you can see the ADC value and compare with a
thermocouple reading.. then you just need to create your own thermistor
table.
Since this merge doesnt change the original information, it doesnt mess
with PC software parsing (tested under Pronterface and Repetier-Host).
This is _not_ automatically the cronological, since deleting a file will free
the filesystem descriptor for it, which then will be used by the next file copied on it.
Since this makes the auto0.g file very inaccessible, I put the option back, to have it in the prepare menu.
this should satisfy https://github.com/ErikZalm/Marlin/pull/373
as a reminder, auto0.g will be executed every time after a boot with sd card present and file present.
thereafter, if there is a file auto1.g this will be done. Thats IMHO the best place to put settings, and prepare heating.
I also execute again after each (now again via the prepare menu) before starting a new print/ after a failed one.
It for me 100% replaces any start.gcode form the slicers.
also, removed some trouble for compilation with corexy.
I think that babystepping is only possible in z for a delta tower.
not sure if it would be usefull to step individual motors on a delta, i don't own one
It is a realtime control over the head position via the LCD menu system that works _while_ printing.
Using it, one can e.g. tune the z-position in realtime, while printing the first layer.
Also, lost steps can be manually added/removed, but thats not the prime feature.
Stuff is placed into the Tune->Babystep *
It is not possible to have realtime control via gcode sending due to the buffering, so I did not include a gcode yet. However, it could be added, but it movements will not be realtime then.
Historically, a very similar thing was implemented for the "Kaamermaker" project, while Joris was babysitting his offspring, hence the name.
say goodby to fuddling around with the z-axis.
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped in either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
Scott Lahteine
Bo Herrmannsen
alexborro
Dim3nsioneer
MyMakibox
whosawhatsis
Matthew Schick
blddk
paciotti
Mark Hanford
Jim Morris
RicardoGA
Erik van der Zalm
fmalpartida
bkubicek
Richard Miles
Robert F-C
Nicolas Rossi