46d59784ad
Rename preocess_command to process_next_command
10 years ago
513077c317
Minor change to fan kick
10 years ago
76438195f0
NO_TIMEOUTS and ADVANCED_OK off by default
10 years ago
d2563804c8
Add LF to file errors
10 years ago
e114662cfa
Adjust SdBaseFile spacing
10 years ago
98e91f5253
Allow lsDive to recurse with minimal stack usage
10 years ago
0f6cd3640b
Drop extraneous ok_to_send
10 years ago
0ce355d9e7
Use MSG_OK in M105
10 years ago
78beef2d73
Use Mendel default for INVERT_Y_DIR
10 years ago
1a4a09c26f
Display unknown XYZ on the LCD as "---"
- Also show 2 digits past decimal for Z on DOGM
10 years ago
68ce419147
Note on segment size
10 years ago
8b92249f18
Bring arc_offset into auto scope
10 years ago
80807b2d71
Consolidate arc code, remove motion_control.*
10 years ago
f65833931d
Formatting tweaks
10 years ago
fcfd99c1ae
Add comments to lcd_control_temperature_menu
10 years ago
d693e0f378
Use WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1 as difference limit
10 years ago
6697a8f375
Watch the heater a little longer
10 years ago
5693a6e3c9
Fix heating error message
10 years ago
27ad381e25
Allow fractional seconds in G4 and M0
10 years ago
b2bd9aae7c
SCARA_SEGMENTS_PER_SECOND
10 years ago
9e95ceb3fc
Split up prepare_move by type
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
10 years ago
873f7d6f2a
Check that configs are up-to-date
10 years ago
f48599f172
add pin definition to some motherboards
10 years ago
b5200e184c
Remove extra setup_for_endstop_move
10 years ago
8d814de558
Return void in prevent_dangerous_extrude
10 years ago
367e2eb9f4
Global setup_for_endstop_move
10 years ago
1d5677cc3b
add missing Z-bits
10 years ago
df12e68e7d
add missing Z_PROBE-bit
10 years ago
fa951f8a0b
Always do st_synchronize() before G28
10 years ago
27a3b1d895
disable sled pin by default
10 years ago
fb44b53ae3
sled improvements
- create sled pin definition
- G28 Works with sled
10 years ago
46d1932380
add plan buffer remaining for 'P' and block buffer remaining 'B'
10 years ago
429c6ccad2
Neaten config formatting
10 years ago
8332a15899
Fix testing of runaway options in temperature.cpp
10 years ago
526ad82d20
activate advanced_ok and no_timeout
10 years ago
2b92b01afc
Fix typo in SanityCheck.h
10 years ago
2445ae3d3a
Combine thermal runaway and watch-period
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
10 years ago
9b3d4380d3
Only watch the heater that was set
10 years ago
b55f32f8a1
replace some bools
this PR replaces some bools with one char. this will safe 3 bytes and should also be sometimes a little bit faster.
10 years ago
e70e6e2b48
Correction traductions
10 years ago
f73f4ce555
Make some z probe and servo code tweaks
10 years ago
28c87ec81b
Disable all heaters on temp error
10 years ago
79106638a8
Fix documentation of heating sanity check
10 years ago
6110494a56
Change default to 4°C in 16s
10 years ago
54deb9eea3
Enable WATCH_TEMP_PERIOD by default
10 years ago
deedb00c18
Document WATCH_TEMP_PERIOD
10 years ago
cb4ea75fab
Support for MKS BASE 1.0 board
10 years ago
0cb87795a3
advanced 'ok'
ok N(linenumber) P(bufferremaining)
the host can use this to send the data much faster.
Some pseudo code:
If (bufferremaining > 0) send command
## as long there is free buffer send command
Also
if (linenumber > lastsend - bufferremaining) send command
## as long last linenumber received is bigger than lastsend (host) - last bufferremaining received
10 years ago
b425851441
Rename Configuration_megatronics.h to Configuration.h
10 years ago
d1148a0198
Rename Configuration_megatronics.h to Configuration.h
10 years ago
Scott Lahteine
Christian Bohn
Wurstnase
Wurstnase
Laurent DELAGE
brupje