af7e3f5076
Print active extruder with M105 for MAX6675
Was omitted when T0 is a MAX6675.
9 years ago
d46d9d998e
Add maximum bed integral term in example configurations.
9 years ago
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
9 years ago
f0523b5816
Initialize the display earlier
to have it ready to display errors during (temperature)-setup.
9 years ago
790c697c19
Fix DEGREES macro
9 years ago
03d5709b09
M110 is a known command
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
9 years ago
d76a01194d
Slight size reduction by adding idle()
9 years ago
2deb5a8ac5
Temporary Hack
REVERT THIS CHANGE
In proper use, we want to force the vendor to update this file to reflect distribution parameters
However, until most users have converted to automatic versioning,
we “grant them a pass”
9 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
9 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
da246f5cb1
Activate BED_MINTEMP error.
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
9 years ago
959da98d8e
Call kill() only once when triggered by a temperature error
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
9 years ago
68f6f149d0
Reduce code size with out_of_range_error function
- Affects code size when automatic bed leveling is enabled
9 years ago
94120740d8
faster compare
!(~(ab)&0x3) and ab == 0x3 are equal
9 years ago
b55f8718c3
Indent G90/G91, G92
9 years ago
b0d520b109
Indent G30, G31/G32
9 years ago
ffe27a6225
Indent G29
9 years ago
86083badc2
Indent G4, G10/G11, G28
9 years ago
47d7a9cb5e
Indent G2/G3
9 years ago
350f239d84
Indent G0/G1
9 years ago
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
9 years ago
15a2351675
No need for +1 on initial seen_pointer
9 years ago
550dd87b2a
Set seen_pointer before calling code_value
9 years ago
063881b5bd
Fix a couple of doubled semicolons
9 years ago
0c0ace2a04
Remove start_watching_heater() fom M104 and M109
9 years ago
00716d0ca0
Small start_watching_heater adjustment
9 years ago
bde9c70d42
Suppress the line mismatch error after M303
9 years ago
ff98b8632b
new endstop bits
9 years ago
9b0fa9c309
Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS
9 years ago
bc0764894a
Shift call of start_watching_heater() into setTargetHotend()
to warrant watching is set or reset.
Make setTargetBed() in _lcd_preheat() dependant of TEMP_SENSOR_BED.
Use disable_all_heaters() in lcd_cooldown() and abort_on_endstop_hit.
9 years ago
b878bc5620
Introducing the Kossel Pro Build Configuration
10 years ago
1d8f61ca8a
AT90USB is defined in pins.h
9 years ago
735bf2d35f
Describe Custom M Code
10 years ago
f39658c822
M120 and M121 are reversed
9 years ago
6eb4f90ce7
Also synchronize configurator copies of configs
10 years ago
9d1961ebe3
Witbox and Hephestos are just RAMPS_13_EFB
10 years ago
89d2ee6f13
Make output on display dependant of ULTRA_LCD
10 years ago
cb6e82dc60
Change from kill() to kill(const char *)
in temperature.cpp
10 years ago
9d13942278
Use new kill() with parameter.
10 years ago
f4a93ed997
Add a string parameter to kill()
Makes the output on the LCD adjustable.
10 years ago
2990c6c45f
Use new kill_() for _temp_error()
instead of stop(). We really want to require a reset and no chance to set a new temperature.
10 years ago
082ed3beed
Propagate Configuration.h changes
Updated all the example Configuration.h files for the new display type.
10 years ago
152b681bb5
Added link to controller github
Added the link to the github information about the
ELB_FULL_GRAPHIC_CONTROLLER
10 years ago
4d4fa3607b
Remove Duemilanove
No way to fit Marlin into 32K.
10 years ago
ca8d1756d5
Define fixes
Fixed a couple defines that were not changed or commented out.
10 years ago
b96b28b7cc
language.h: update documentation for LANGUAGE_INCLUDE
language.h: update documentation for LANGUAGE_INCLUDE
@thinkyhead What do you think? I think there should be a warning like
this.
10 years ago
258bcdefe0
move dogm font selection to configuration_adv.h
10 years ago
7750180c93
transpire -> expire
Minor wording correction.
10 years ago
70163dafb9
Use _temp_error() for all errors thrown by different mechanisms
Now ending in an endless loop.
Tidy up the output format.
We now get:
ERRORTEXT ", system stopped! Heater_ID: " HEATERID
Where ERRORTEXT can be:
"Heating failed"
"Thermal Runaway"
"MAXTEMP triggered"
"MINTEMP triggered"
and soon
"Thermal Jump"
HEATERID can be
0, 1, 2 ,3 , "bed"
This messages are always followed by the common:
"Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
10 years ago
a0f362c735
Simplify & optimize with current_command_args
10 years ago
AnHardt
Jonathan Bastien-Filiatrault
Scott Lahteine
Richard Wackerbarth
wurstnase
Ed Boston
CONSULitAS
Christian Bohn