a274769f4f
Clean up spacing and comments
Also clean up some trailing spaces in a few other sources
10 years ago
d3bce05d54
Fix up spacing for filament sensor values
10 years ago
b4b10a57fe
Fix configurator section directives and values lists
10 years ago
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
10 years ago
06906bc1c8
Merge (PR#2295)
10 years ago
318318b02f
Add pins_RAMPS_13_EFB.h to reduce redundancy
10 years ago
346c8b339b
Remove a test from pins_RAMPS_13.h
- Add 3 new lines to `pins.h` to remove 2 redundant tests in
`pins_RAMPS_13.h`
10 years ago
b93cddfcc9
Add lost MKS_BASE to pins.h (PR#2297)
10 years ago
6ab7b560af
Rework buzzing (PR#2296)
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.
Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.
All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.
To do: Check the conditions for the BEEPER-pin in all pin-files.
10 years ago
29122db2fa
Fix ULTRA_LCD spelling in HAS_LCD_BUZZ
10 years ago
1418470ae9
Merge PR( #2271 )
10 years ago
1d94d098bf
Formatting tweaks as part of fixing issue 1497
10 years ago
e602c28ad9
Set auto fan pins to OUTPUT during init
Fixes the problem of these pins being left in INPUT state, as described
in #1497
10 years ago
90f858aa85
Use translated strings for axis movement (PR#2280)
Suggest we use the translated strings here. They use (except for
German) the phrasing “Move X” instead of just the axis letter, but they
should fit the available space. The “Extruder” string would be the
same, except it will be translated.
10 years ago
e2a4a83586
Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281 )
10 years ago
6b1b3adaf0
Consistent punctuation in SanityCheck errors (PR#2283)
10 years ago
eb81982fcd
Fix error next command in autotune (PR#2274)
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
10 years ago
55b23c896a
Optimise out_of_range_error() (PR#2265)
by avoiding the strncopy()
10 years ago
b0860adab6
Fix volumetric multiplier display for filament sensor (PR#2264)
The volumetric multiplier display needs to be multiplied by 100 in order to make it an integer for display purposes.
10 years ago
45642b7fe8
Respect DISABLE_AXIS settings (PR#2216)
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
10 years ago
c85a486445
make the dual z-endstop optional (PR#2277)
it's disabled by default
10 years ago
962b107341
Prevent current_command_args from bypassing nul (PR#2270)
10 years ago
4061279218
Merge pull request #2260 from Wackerbarth/DropArduino0.x.x
Deprecate Support for Arduino IDE < 1.0.5
10 years ago
06ae832276
Deprecate Support for Arduino IDE < 1.0.5
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
10 years ago
4c3ca0b5b6
Deprecate Support for Arduino IDE < 1.0.5
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
10 years ago
ff6081be3a
Parse N[0-9]+[ ]* differently (PR #2263 )
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
10 years ago
d8e2f5d333
Merge pull request #2167 from thinkyhead/reverse_zoffset_sign
Reverse the sign of zprobe_zoffset
10 years ago
aad121864e
Include "Z" in M851 report
10 years ago
96a3fba8ac
Reverse the sign of zprobe_zoffset
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
10 years ago
1ad2c5bfc0
Merge pull request #2257 from fmalpartida/bugFixing
Updated SAV MkI extension module header connector.
10 years ago
f92907183c
Updated SAV MkI pin header.
10 years ago
58941e543e
ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
#defining something just to define something else doesn’t
make sense
If you want SDCARDDETECTINVERTED, just define it yourself.
If the previous code was intended to define, undefined and then again define the term, that code is improper.
10 years ago
cf5d64d940
Merge PR #2118
10 years ago
788eb6e647
planner.cpp: remove tab
planner.cpp: single evil and hidden tab removed ♻️ 😏
10 years ago
3a5963c0e7
Configuration_adv.h: Add FAN_MIN_PWM for slow fan stopping issue …
* all Configuration_adv.h: Add #define FAN_MIN_PWM for slow fan stopping
issue
* for K8200: uncommented with tested (and working) values
10 years ago
e55e65d1e4
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
@CONSULitAS
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)
@thinkyhead thanks for idea on linear scaling
10 years ago
5239a4e839
Merge bPR #1882
10 years ago
8d295547be
* Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button.
10 years ago
3eea5222cf
Merge PR #1767
10 years ago
6d0e91328d
Renamed Board_megatronics_1 to Board_minitronics
10 years ago
c4a2e5ac23
Renamed Pins_megatronics_1 to Pins_minitronics
10 years ago
2076906aaa
Renamed Pins_megatronics_1 to Pins_minitronics
10 years ago
10733a2bb0
added minirambo pin definitions. V2
10 years ago
0c7bdf569c
Merge branch 'ProbeDeployment' into Development
10 years ago
303d47228e
Define Probe Path in new format
10 years ago
ad09d6a60f
3 Step Allen Key Probe
10 years ago
8359cdf01d
Check compatibility for Teensy-based processor
The instruction say to set a #define in fastio.h
However, that value is not included before this test.
10 years ago
6b095af9b1
Merge branch 'GenerateVersionHeader' into Development
10 years ago
b3a3080b4b
Suppress error when on detached head
10 years ago
54375cc7a4
Quote paths so build scripts work when directories have space in their name.
Currently if you clone Marlin to a directory with a space in the name, Arduino will generate an error.
Because when executed the path ends up split into two separate arguments.
10 years ago
Scott Lahteine
Richard Wackerbarth
AnHardt
Scott Lahteine
MagoKimbra
filipmu
wurstnase
fmalpartida
CONSULitAS
paclema
atfield90
tonokip
Daniel Friesen