From ffe0e2d19aea47b9f51937cc40a9bcaa3a370e1d Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Fri, 7 Apr 2017 13:52:21 -0500 Subject: [PATCH] SPINDLE/LASER pins changes --- Marlin/pinsDebug_list.h | 4 +- Marlin/pins_3DRAG.h | 57 +++++++++ Marlin/pins_AZTEEG_X3.h | 35 ++++++ Marlin/pins_AZTEEG_X3_PRO.h | 38 ++++++ Marlin/pins_BAM_DICE_DUE.h | 7 ++ Marlin/pins_BQ_ZUM_MEGA_3D.h | 12 ++ Marlin/pins_BRAINWAVE.h | 34 +++++ Marlin/pins_BRAINWAVE_PRO.h | 60 ++++++++- Marlin/pins_FELIX2.h | 7 ++ Marlin/pins_GEN3_MONOLITHIC.h | 26 ++++ Marlin/pins_GEN3_PLUS.h | 27 +++- Marlin/pins_GEN6.h | 35 ++++++ Marlin/pins_GEN6_DELUXE.h | 26 ++++ Marlin/pins_GEN7_12.h | 52 +++++++- Marlin/pins_GEN7_13.h | 25 ++++ Marlin/pins_GEN7_14.h | 49 ++++++-- Marlin/pins_GEN7_CUSTOM.h | 37 +++++- Marlin/pins_K8400.h | 5 + Marlin/pins_MEGACONTROLLER.h | 8 ++ Marlin/pins_MEGATRONICS.h | 8 ++ Marlin/pins_MEGATRONICS_2.h | 12 +- Marlin/pins_MEGATRONICS_3.h | 27 ++++ Marlin/pins_MIGHTYBOARD_REVE.h | 31 ++++- Marlin/pins_MINIRAMBO.h | 10 ++ Marlin/pins_MINITRONICS.h | 23 ++++ Marlin/pins_MKS_BASE.h | 13 +- Marlin/pins_OMCA.h | 25 ++++ Marlin/pins_OMCA_A.h | 27 +++- Marlin/pins_RAMBO.h | 8 ++ Marlin/pins_RAMPS.h | 26 ++++ Marlin/pins_RAMPS_OLD.h | 8 ++ Marlin/pins_RIGIDBOARD.h | 18 +-- Marlin/pins_RUMBA.h | 12 +- Marlin/pins_SANGUINOLOLU_11.h | 98 +++++++++++++-- Marlin/pins_SAV_MKI.h | 16 ++- Marlin/pins_SETHI.h | 25 ++++ Marlin/pins_TEENSY2.h | 8 ++ Marlin/pins_TEENSYLU.h | 163 ++++++++++++++++-------- Marlin/pins_ULTIMAIN_2.h | 21 ++++ Marlin/pins_ULTIMAKER.h | 16 +++ Marlin/pins_ULTIMAKER_OLD.h | 220 ++++++++++++++++++++++++++++++--- 41 files changed, 1248 insertions(+), 111 deletions(-) diff --git a/Marlin/pinsDebug_list.h b/Marlin/pinsDebug_list.h index 758c332dc8..dfdd411046 100644 --- a/Marlin/pinsDebug_list.h +++ b/Marlin/pinsDebug_list.h @@ -515,8 +515,8 @@ #if PIN_EXISTS(SPINDLE_LASER_ENABLE) REPORT_NAME_DIGITAL(SPINDLE_LASER_ENABLE_PIN, __LINE__ ) #endif -#if PIN_EXISTS(SPINDLE_SPEED_LASER_POWER) - REPORT_NAME_DIGITAL(SPINDLE_SPEED_LASER_POWER_PIN, __LINE__ ) +#if PIN_EXISTS(SPINDLE_LASER_PWM) + REPORT_NAME_DIGITAL(SPINDLE_LASER_PWM_PIN, __LINE__ ) #endif #if PIN_EXISTS(SR_CLK) REPORT_NAME_DIGITAL(SR_CLK_PIN, __LINE__ ) diff --git a/Marlin/pins_3DRAG.h b/Marlin/pins_3DRAG.h index 9eaf2c9f65..feadea4e3c 100644 --- a/Marlin/pins_3DRAG.h +++ b/Marlin/pins_3DRAG.h @@ -43,6 +43,8 @@ #define RAMPS_D9_PIN 8 #define MOSFET_D_PIN 12 +#define CASE_LIGHT_PIN -1 // MUST BE HARDWARE PWM but one is not available on expansion header + #include "pins_RAMPS.h" // @@ -104,3 +106,58 @@ #define BEEPER_PIN 33 #endif // ULTRA_LCD && NEWPANEL + +/** + * M3/M4/M5 - Spindle/Laser Control + * + * If you want to control the speed of your spindle then you'll have + * have to sacrifce the Extruder and pull some signals off the Z stepper + * driver socket. + * + * The following assumes: + * - the Z stepper driver socket is empty + * - the extruder driver socket has a driver board plugged into it + * - the Z stepper wires are attached the the extruder connector + * + * If you want to keep the extruder AND don't have a LCD display then + * you can still control the power on/off and spindle direction. + * + * Where to get spindle signals + * + * stepper signal socket name socket name + * ------- + * SPINDLE_LASER_ENABLE_PIN /ENABLE O| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_LASER_PWM_PIN STEP O| |O VDD + * SPINDLE_DIR_PIN DIR O| |O GND + * ------- + * + * Note: Socket names vary from vendor to vendor + */ +#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not good with 3DRAG +#undef SPINDLE_LASER_ENABLE_PIN +#undef SPINDLE_DIR_PIN + +#if ENABLED(SPINDLE_LASER_ENABLE) + #if !EXTRUDERS + #undef E0_DIR_PIN + #undef E0_ENABLE_PIN + #undef E0_STEP_PIN + #undef Z_DIR_PIN + #undef Z_ENABLE_PIN + #undef Z_STEP_PIN + #define Z_DIR_PIN 28 + #define Z_ENABLE_PIN 24 + #define Z_STEP_PIN 26 + #define SPINDLE_LASER_PWM_PIN 46 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 62 // Pin should have a pullup! + #define SPINDLE_DIR_PIN 48 + #elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // use expansion header if no LCD in use + #define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup/pulldown! + #define SPINDLE_DIR_PIN 17 + #endif +#endif diff --git a/Marlin/pins_AZTEEG_X3.h b/Marlin/pins_AZTEEG_X3.h index 364697d608..430a9fa427 100644 --- a/Marlin/pins_AZTEEG_X3.h +++ b/Marlin/pins_AZTEEG_X3.h @@ -24,12 +24,20 @@ * AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments */ +#ifndef __AVR_ATmega2560__ + #error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu." +#endif + #if HOTENDS > 2 || E_STEPPERS > 2 #error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif #define BOARD_NAME "Azteeg X3" +#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming + #define OK_TO_CHANGE_CASE_LIGHT // in from from the include file +#endif + #include "pins_RAMPS_13.h" // @@ -63,3 +71,30 @@ #define STAT_LED_BLUE_PIN 11 #endif + +// +// Misc +// +#if ENABLED(OK_TO_CHANGE_CASE_LIGHT) && STAT_LED_RED_PIN == 6 + #undef STAT_LED_RED_PIN + #undef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 6 // open collector FET driver +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board +#undef SPINDLE_LASER_ENABLE_PIN +#undef SPINDLE_DIR_PIN + +#if ENABLED(SPINDLE_LASER_ENABLE) + #undef SDA // use EXP3 header + #undef SCL + #if SERVO0_PIN == 7 + #undef SERVO0_PIN + #def SERVO0_PIN 11 + #define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup! + #define SPINDLE_DIR_PIN 21 +#endif diff --git a/Marlin/pins_AZTEEG_X3_PRO.h b/Marlin/pins_AZTEEG_X3_PRO.h index 41df3be5b8..7701f8b681 100644 --- a/Marlin/pins_AZTEEG_X3_PRO.h +++ b/Marlin/pins_AZTEEG_X3_PRO.h @@ -30,8 +30,16 @@ #define BOARD_NAME "Azteeg X3 Pro" +#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming + #define OK_TO_CHANGE_CASE_LIGHT // in from from the include file +#endif + #include "pins_RAMPS.h" +#ifndef __AVR_ATmega2560__ + #error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu." +#endif + // // Servos // @@ -126,7 +134,37 @@ #if ENABLED(VIKI2) || ENABLED(miniVIKI) #undef SD_DETECT_PIN #define SD_DETECT_PIN 49 // For easy adapter board + #undef BEEPER_PIN + #define BEEPER_PIN 12 // 33 isn't physically available to the LCD display #else #define STAT_LED_RED_PIN 32 #define STAT_LED_BLUE_PIN 35 #endif + +// +// Misc. Functions +// +#undef DOGLCD_A0 // steal pin 44 for the case light +#define DOGLCD_A0 57 +#if ENABLED(OK_TO_CHANGE_CASE_LIGHT) + #undef CASE_LIGHT_PIN + #define CASE_LIGHT_PIN 44 // must have a hardware PWM +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board +#undef SPINDLE_LASER_ENABLE_PIN +#undef SPINDLE_DIR_PIN + +#if ENABLED(SPINDLE_LASER_ENABLE) // use EXP2 header + #if ENABLED(VIKI2) || ENABLED(miniVIKI) + #undef BTN_EN2 + #define BTN_EN2 31 // need 7 for the spindle speed PWM + #endif + #define SPINDLE_LASER_PWM_PIN 7 // must have a hardware PWM + #define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup! + #define SPINDLE_DIR_PIN 21 +#endif + diff --git a/Marlin/pins_BAM_DICE_DUE.h b/Marlin/pins_BAM_DICE_DUE.h index 0da4f08c40..2b34cddd83 100644 --- a/Marlin/pins_BAM_DICE_DUE.h +++ b/Marlin/pins_BAM_DICE_DUE.h @@ -30,6 +30,13 @@ #define BOARD_NAME "2PrintBeta Due" +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 66 // Pin should have a pullup/pulldown! +#define SPINDLE_DIR_PIN 67 +#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #include "pins_RAMPS.h" // diff --git a/Marlin/pins_BQ_ZUM_MEGA_3D.h b/Marlin/pins_BQ_ZUM_MEGA_3D.h index 402c1cb2ff..84722f11c9 100644 --- a/Marlin/pins_BQ_ZUM_MEGA_3D.h +++ b/Marlin/pins_BQ_ZUM_MEGA_3D.h @@ -46,6 +46,18 @@ #define ORIG_E2_AUTO_FAN_PIN 6 #define ORIG_E3_AUTO_FAN_PIN 6 +// +// Misc. Functions +// +#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 42 + #include "pins_RAMPS_13.h" // diff --git a/Marlin/pins_BRAINWAVE.h b/Marlin/pins_BRAINWAVE.h index ba9d04099c..0d17cac10f 100644 --- a/Marlin/pins_BRAINWAVE.h +++ b/Marlin/pins_BRAINWAVE.h @@ -27,6 +27,40 @@ * https://github.com/unrepentantgeek/brainwave-arduino */ +/** + * Rev B 16 JAN 2017 + * + * Added pointer to a currently available Arduino IDE extension that will + * allow this board to use the latest Marlin software + */ + +/** + * Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB + * This is the only known IDE extension that is compatible with the pin definitions + * in this file, Adrduino 1.6.12 and the latest mainstream Marlin software. + * + * "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share + * the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such + * that PWM1A, PWM1B & PWM1C can not be used. + * + * Installation: + * + * 1. In the Arduino IDE, under Files -> Preferences paste the following URL + * https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json + * 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB + * and then click on "Install" + * 3. Select "AT90USB646_STANDARD" from the 'Tools -> Boards' menu. + */ + +/** + * To burn the bootloader that comes with Marlin_AT90USB: + * + * 1. Connect your programmer to the board. + * 2. In Arduino IDE select "AT90USB646_STANDARD" and then select the programmer. + * 3. In Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + #ifndef __AVR_AT90USB646__ #error "Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu." #endif diff --git a/Marlin/pins_BRAINWAVE_PRO.h b/Marlin/pins_BRAINWAVE_PRO.h index b353581f0a..1884d3cb13 100644 --- a/Marlin/pins_BRAINWAVE_PRO.h +++ b/Marlin/pins_BRAINWAVE_PRO.h @@ -27,14 +27,70 @@ * https://github.com/unrepentantgeek/brainwave-arduino */ +/** + * Rev B 16 JAN 2017 + * + * Added pointers to currently available Arduino IDE extensions that will + * allow this board to use the latest Marlin software + */ + +/** + * There are three Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. All have been used with Arduino 1.6.12 + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu + * + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. + * + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * This is basically Teensyduino but with a bootloader that can handle image sizes + * larger than 64K. + * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB + * Uses the bootloader from Printerboard above. + * + * "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share + * the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such + * that PWM1A, PWM1B & PWM1C can not be used. + * + * Installation: + * + * 1. In the Arduino IDE, under Files -> Preferences paste the following URL + * https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json + * 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB + * and then click on "Install" + * 3. Select "AT90USB1286_TEENSYPP" from the 'Tools -> Boards' menu. + */ + +/** + * To burn the bootloader that comes with Printrboard and Marlin_AT90USB: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" or "AT90USB1286_TEENSYPP" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + #ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Brainwave Pro' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Teensy++ 2.0', 'AT90USB1286_TEENSYPP', or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #include "fastio.h" #if DISABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical. - #error "Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config" + #error "Uncomment '#define AT90USBxx_TEENSYPP_ASSIGNMENTS' in fastio.h for this config" #endif #define BOARD_NAME "Brainwave Pro" diff --git a/Marlin/pins_FELIX2.h b/Marlin/pins_FELIX2.h index 28894fe97a..5d6765c840 100644 --- a/Marlin/pins_FELIX2.h +++ b/Marlin/pins_FELIX2.h @@ -54,3 +54,10 @@ #define SD_DETECT_PIN 6 #endif // NEWPANEL && ULTRA_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// +#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not valid with this board +#undef SPINDLE_LASER_ENABLE_PIN +#undef SPINDLE_DIR_PIN diff --git a/Marlin/pins_GEN3_MONOLITHIC.h b/Marlin/pins_GEN3_MONOLITHIC.h index e7a5dfb0d1..dae4046fd2 100644 --- a/Marlin/pins_GEN3_MONOLITHIC.h +++ b/Marlin/pins_GEN3_MONOLITHIC.h @@ -24,6 +24,31 @@ * Gen3 Monolithic Electronics pin assignments */ +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #ifndef __AVR_ATmega644P__ #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif @@ -73,3 +98,4 @@ #define PS_ON_PIN 14 // Alex, does this work on the card? // Alex extras from Gen3+ + diff --git a/Marlin/pins_GEN3_PLUS.h b/Marlin/pins_GEN3_PLUS.h index b5236d87ea..85c47305b3 100644 --- a/Marlin/pins_GEN3_PLUS.h +++ b/Marlin/pins_GEN3_PLUS.h @@ -24,6 +24,32 @@ * Gen3+ pin assignments */ +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the SANGUINO board and then select the CPU. + * + */ + + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif @@ -73,4 +99,3 @@ // #define SDSS 4 #define PS_ON_PIN 14 - diff --git a/Marlin/pins_GEN6.h b/Marlin/pins_GEN6.h index 9d1e1bcf18..10a285790d 100644 --- a/Marlin/pins_GEN6.h +++ b/Marlin/pins_GEN6.h @@ -24,6 +24,33 @@ * Gen6 pin assignments */ + /** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega1284P__ #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." @@ -80,7 +107,15 @@ // #define SDSS 17 #define DEBUG_PIN 0 +#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM // RS485 pins #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 6 diff --git a/Marlin/pins_GEN6_DELUXE.h b/Marlin/pins_GEN6_DELUXE.h index b1a1037ed9..5834068667 100644 --- a/Marlin/pins_GEN6_DELUXE.h +++ b/Marlin/pins_GEN6_DELUXE.h @@ -24,6 +24,32 @@ * Gen6 Deluxe pin assignments */ +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the SANGUINO board and then select the CPU. + * + */ + + #define BOARD_NAME "Gen6 Deluxe" #include "pins_GEN6.h" diff --git a/Marlin/pins_GEN7_12.h b/Marlin/pins_GEN7_12.h index 53edb32811..b0f178ff34 100644 --- a/Marlin/pins_GEN7_12.h +++ b/Marlin/pins_GEN7_12.h @@ -24,8 +24,35 @@ * Gen7 v1.1, v1.2, v1.3 pin assignments */ + /** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) - #error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif #ifndef BOARD_NAME @@ -39,10 +66,13 @@ // // Limit Switches // -#define X_STOP_PIN 7 -#define Y_STOP_PIN 5 +#define X_MIN_PIN 7 +#define Y_MIN_PIN 5 #define Z_MIN_PIN 1 #define Z_MAX_PIN 0 +#define Y_MAX_PIN 2 +#define X_MAX_PIN 6 + // // Z Probe (when not Z_MIN_PIN) @@ -91,6 +121,12 @@ // #define PS_ON_PIN 15 +#if GEN7_VERSION < 13 + #define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM +#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header + #define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM +#endif + // All these generations of Gen7 supply thermistor power // via PS_ON, so ignore bad thermistor readings #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE @@ -101,3 +137,13 @@ #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown! +#define SPINDLE_DIR_PIN 11 +#if GEN7_VERSION < 13 + #define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header + #define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM +#endif diff --git a/Marlin/pins_GEN7_13.h b/Marlin/pins_GEN7_13.h index 2365ae8be8..03ea131f46 100644 --- a/Marlin/pins_GEN7_13.h +++ b/Marlin/pins_GEN7_13.h @@ -24,6 +24,31 @@ * Gen7 v1.3 pin assignments */ + /** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #define BOARD_NAME "Gen7 v1.3" #define GEN7_VERSION 13 // v1.3 diff --git a/Marlin/pins_GEN7_14.h b/Marlin/pins_GEN7_14.h index d200137b48..9d4e16af33 100644 --- a/Marlin/pins_GEN7_14.h +++ b/Marlin/pins_GEN7_14.h @@ -24,8 +24,35 @@ * Gen7 v1.4 pin assignments */ +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) - #error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Gen7 v1.4" @@ -67,17 +94,25 @@ // // Heaters // -#define HEATER_0_PIN 4 -#define HEATER_BED_PIN 3 +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 // // Misc. Functions // -#define PS_ON_PIN 15 +#define PS_ON_PIN 15 +#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM // A pin for debugging -#define DEBUG_PIN 0 +#define DEBUG_PIN 0 // RS485 pins -#define TX_ENABLE_PIN 12 -#define RX_ENABLE_PIN 13 +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 21 diff --git a/Marlin/pins_GEN7_CUSTOM.h b/Marlin/pins_GEN7_CUSTOM.h index 81809d61ae..9b83df9aee 100644 --- a/Marlin/pins_GEN7_CUSTOM.h +++ b/Marlin/pins_GEN7_CUSTOM.h @@ -27,8 +27,35 @@ * Please review the pins and adjust them for your needs. */ +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) - #error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Gen7 Custom" @@ -76,6 +103,7 @@ // #define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support #define PS_ON_PIN 19 +#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM // A pin for debugging #define DEBUG_PIN -1 @@ -101,3 +129,10 @@ // RS485 pins //#define TX_ENABLE_PIN 12 //#define RX_ENABLE_PIN 13 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 6 diff --git a/Marlin/pins_K8400.h b/Marlin/pins_K8400.h index 1ef8049c13..3e2cd4b212 100644 --- a/Marlin/pins_K8400.h +++ b/Marlin/pins_K8400.h @@ -66,3 +66,8 @@ #undef PS_ON_PIN #undef KILL_PIN #undef SD_DETECT_PIN + +#if Z_STEP_PIN == 26 + #undef Z_STEP_PIN + #define Z_STEP_PIN 32 +#endif diff --git a/Marlin/pins_MEGACONTROLLER.h b/Marlin/pins_MEGACONTROLLER.h index c81f3547b8..c4a10705ab 100644 --- a/Marlin/pins_MEGACONTROLLER.h +++ b/Marlin/pins_MEGACONTROLLER.h @@ -127,6 +127,7 @@ // #define SDSS 53 #define LED_PIN 13 +#define CASE_LIGHT_PIN 2 // // LCD / Controller @@ -152,3 +153,10 @@ #define SD_DETECT_PIN 49 #endif // MINIPANEL + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 7 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 8 diff --git a/Marlin/pins_MEGATRONICS.h b/Marlin/pins_MEGATRONICS.h index 5b8d41f4f5..ba97fa2556 100644 --- a/Marlin/pins_MEGATRONICS.h +++ b/Marlin/pins_MEGATRONICS.h @@ -97,6 +97,7 @@ #define SDSS 53 #define LED_PIN 13 #define PS_ON_PIN 12 +#define CASE_LIGHT_PIN 2 // // LCD / Controller @@ -120,3 +121,10 @@ #define SD_DETECT_PIN -1 // RAMPS doesn't use this #endif // ULTRA_LCD && NEWPANEL + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 11 diff --git a/Marlin/pins_MEGATRONICS_2.h b/Marlin/pins_MEGATRONICS_2.h index be3ed4cf4a..0cbb769453 100644 --- a/Marlin/pins_MEGATRONICS_2.h +++ b/Marlin/pins_MEGATRONICS_2.h @@ -71,8 +71,8 @@ #define E1_DIR_PIN 39 #define E1_ENABLE_PIN 28 -#define E2_STEP_PIN 23 -#define E2_DIR_PIN 24 +#define E2_STEP_PIN 23 // ? schematic says 24 +#define E2_DIR_PIN 24 // ? schematic says 23 #define E2_ENABLE_PIN 22 // @@ -112,6 +112,7 @@ #define SDSS 53 #define LED_PIN 13 #define PS_ON_PIN 12 +#define CASE_LIGHT_PIN 2 // // LCD / Controller @@ -129,3 +130,10 @@ #define BTN_EN1 61 #define BTN_EN2 59 #define BTN_ENC 43 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 11 diff --git a/Marlin/pins_MEGATRONICS_3.h b/Marlin/pins_MEGATRONICS_3.h index 419f80ba59..aa6c40374f 100644 --- a/Marlin/pins_MEGATRONICS_3.h +++ b/Marlin/pins_MEGATRONICS_3.h @@ -28,6 +28,8 @@ #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif +#define MEGATRONICS_31 + #if ENABLED(MEGATRONICS_31) #define BOARD_NAME "Megatronics v3.1" #else @@ -129,6 +131,7 @@ #define SDSS 53 #define LED_PIN 13 #define PS_ON_PIN 12 +#define CASE_LIGHT_PIN 45 // try the keypad connector // // LCD / Controller @@ -164,3 +167,27 @@ #endif #endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if DISABLED(REPRAPWORLD_KEYPAD) // try to use the keypad connector first + #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 43 // Pin should have a pullup! + #define SPINDLE_DIR_PIN 42 +#elif EXTRUDERS <= 2 + // try to hijack the last extruder so that we can get the PWM signal off the Y breakout + // move all the Y signals to the E2 extruder socket - makes dual Y steppers harder + #undef Y_ENABLE_PIN + #undef Y_STEP_PIN + #undef Y_DIR_PIN + #undef E2_STEP_PIN + #undef E2_ENABLE_PIN + #undef E2_DIR_PIN + #define Y_ENABLE_PIN 23 + #define Y_STEP_PIN 22 + #define Y_DIR_PIN 60 + #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup! + #define SPINDLE_DIR_PIN 5 +#endif diff --git a/Marlin/pins_MIGHTYBOARD_REVE.h b/Marlin/pins_MIGHTYBOARD_REVE.h index 933486177e..bd13a379d9 100644 --- a/Marlin/pins_MIGHTYBOARD_REVE.h +++ b/Marlin/pins_MIGHTYBOARD_REVE.h @@ -41,6 +41,17 @@ * */ +/** + * Rev B 2 JAN 2017 + * + * Added pin definitions for: + * M3, M4 & M5 spindle control commands + * case light + * + * Corrected pin assignment for MOSFET_B_PIN pin. Changed it from 9 to 11. The port + * number (B5) agrees with the schematic but B5 is assigned to logical pin 11. + */ + #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif @@ -140,7 +151,7 @@ // With no heated bed, an additional 24V fan is possible. // #define MOSFET_A_PIN 6 // H3 -#define MOSFET_B_PIN 11 // B5 +#define MOSFET_B_PIN 11 // B5 - Rev A of this file had this pin assigned to 9 #define MOSFET_C_PIN 45 // L4 #define MOSFET_D_PIN 44 // L5 @@ -193,11 +204,11 @@ #define LED_PIN 13 // B7 #define CUTOFF_RESET_PIN 16 // H1 #define CUTOFF_TEST_PIN 17 // H0 +#define CASE_LIGHT_PIN 44 // L5 MUST BE HARDWARE PWM // // LCD / Controller // - #ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER #define LCD_PINS_RS 33 // C4, LCD-STROBE @@ -246,7 +257,6 @@ #endif - // // SD Card // @@ -255,7 +265,20 @@ #define MAX_PIN THERMO_SCK_PIN -//check if all pins are defined in mega/pins_arduino.h +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 66 // K4 Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 8 // H5 MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 67 // K5 + + + + + + + +// Check if all pins are defined in mega/pins_arduino.h #include static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h" "to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below"); diff --git a/Marlin/pins_MINIRAMBO.h b/Marlin/pins_MINIRAMBO.h index 551926a5fa..de3c6b08ae 100644 --- a/Marlin/pins_MINIRAMBO.h +++ b/Marlin/pins_MINIRAMBO.h @@ -111,6 +111,7 @@ // #define SDSS 53 #define LED_PIN 13 +#define CASE_LIGHT_PIN 9 // // LCD / Controller @@ -140,3 +141,12 @@ #endif // NEWPANEL #endif // ULTRA_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// + +// use P1 connector for spindle pins +#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 19 diff --git a/Marlin/pins_MINITRONICS.h b/Marlin/pins_MINITRONICS.h index d9a03c41fc..43f63ab231 100644 --- a/Marlin/pins_MINITRONICS.h +++ b/Marlin/pins_MINITRONICS.h @@ -24,6 +24,13 @@ * Minitronics v1.0/1.1 pin assignments */ +/** + * Rev B 2 JAN 2017 + * + * Added pin definitions for M3, M4 & M5 spindle control commands + * + */ + #ifndef __AVR_ATmega1281__ #error "Oops! Make sure you have 'Minitronics' selected from the 'Tools -> Boards' menu." #endif @@ -123,3 +130,19 @@ #define SD_DETECT_PIN -1 // Minitronics doesn't use this #endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) // assumes we're only doing CNC work (no 3D printing) + #undef HEATER_BED_PIN + #undef TEMP_BED_PIN // need to free up some pins but also need to + #undef TEMP_0_PIN // re-assign them (to unused pins) because Marlin + #undef TEMP_1_PIN // requires the presence of certain pins or else it + #define HEATER_BED_PIN 4 // won't compile + #define TEMP_BED_PIN 50 + #define TEMP_0_PIN 51 + #define SPINDLE_LASER_ENABLE_PIN 52 // using A6 because it already has a pull up on it + #define SPINDLE_LASER_PWM_PIN 3 // WARNING - LED & resistor pull up to +12/+24V stepper voltage + #define SPINDLE_DIR_PIN 53 +#endif diff --git a/Marlin/pins_MKS_BASE.h b/Marlin/pins_MKS_BASE.h index 12bf8b7491..dcf9b90f29 100644 --- a/Marlin/pins_MKS_BASE.h +++ b/Marlin/pins_MKS_BASE.h @@ -22,6 +22,8 @@ /** * MKS BASE 1.0 – Arduino Mega2560 with RAMPS v1.4 pin assignments + * + * Rev B - Override pin definitions for CASE_LIGHT and M3/M4/M5 spindle control */ #if HOTENDS > 2 || E_STEPPERS > 2 @@ -36,4 +38,13 @@ // Power outputs EFBF or EFBE #define MOSFET_D_PIN 7 -#include "pins_RAMPS.h" \ No newline at end of file +#define CASE_LIGHT_PIN 2 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 2 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 15 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 19 + +#include "pins_RAMPS.h" diff --git a/Marlin/pins_OMCA.h b/Marlin/pins_OMCA.h index 545c8646f2..8715efcd44 100644 --- a/Marlin/pins_OMCA.h +++ b/Marlin/pins_OMCA.h @@ -51,6 +51,31 @@ * REF http://sanguino.cc/hardware */ +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)" #endif diff --git a/Marlin/pins_OMCA_A.h b/Marlin/pins_OMCA_A.h index d325a648d9..3686973c95 100644 --- a/Marlin/pins_OMCA_A.h +++ b/Marlin/pins_OMCA_A.h @@ -50,8 +50,33 @@ * */ +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #ifndef __AVR_ATmega644__ - #error "Oops! Make sure you have 'SanguinoA' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Alpha OMCA" diff --git a/Marlin/pins_RAMBO.h b/Marlin/pins_RAMBO.h index e4df16677f..c99cd79233 100644 --- a/Marlin/pins_RAMBO.h +++ b/Marlin/pins_RAMBO.h @@ -137,6 +137,7 @@ #define LED_PIN 13 #define FILWIDTH_PIN 3 // Analog Input #define PS_ON_PIN 4 +#define CASE_LIGHT_PIN 46 // // LCD / Controller @@ -208,3 +209,10 @@ #endif // !NEWPANEL #endif // ULTRA_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 31 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 32 diff --git a/Marlin/pins_RAMPS.h b/Marlin/pins_RAMPS.h index 767e990857..9bd1a252c3 100644 --- a/Marlin/pins_RAMPS.h +++ b/Marlin/pins_RAMPS.h @@ -204,6 +204,16 @@ #define PS_ON_PIN 12 +#if !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) + #undef CASE_LIGHT_PIN + #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first + #define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM + #elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \ + && (ENABLED(PANEL_ONE) || ENABLED(VIKI2) || ENABLED(miniVIKI) || ENABLED(MINIPANEL) || ENABLED(REPRAPWORLD_KEYPAD))) // try to use AUX 2 + #define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM + #endif +#endif + // // LCD / Controller // @@ -361,3 +371,19 @@ #endif // NEWPANEL #endif // ULTRA_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE_PIN) + #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first + #define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN 5 + #elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \ + && (ENABLED(PANEL_ONE) || ENABLED(VIKI2) || ENABLED(miniVIKI) || ENABLED(MINIPANEL) || ENABLED(REPRAPWORLD_KEYPAD))) // try to use AUX 2 + #define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN 65 + #endif +#endif diff --git a/Marlin/pins_RAMPS_OLD.h b/Marlin/pins_RAMPS_OLD.h index 29812bbdf4..870f2fbd15 100644 --- a/Marlin/pins_RAMPS_OLD.h +++ b/Marlin/pins_RAMPS_OLD.h @@ -101,3 +101,11 @@ #define SDPOWER 48 #define SDSS 53 #define LED_PIN 13 +#define CASE_LIGHT_PIN 45 // MUST BE HARDWARE PWM + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 43 diff --git a/Marlin/pins_RIGIDBOARD.h b/Marlin/pins_RIGIDBOARD.h index 0e48caf73b..5bd06e40eb 100644 --- a/Marlin/pins_RIGIDBOARD.h +++ b/Marlin/pins_RIGIDBOARD.h @@ -82,16 +82,16 @@ // // Heaters / Fans // -#undef HEATER_BED_PIN +#undef HEATER_BED_PIN #define HEATER_BED_PIN 10 -#undef FAN_PIN +#undef FAN_PIN #define FAN_PIN 8 // Same as RAMPS_13_EEF // // Misc. Functions // -#undef PS_ON_PIN +#undef PS_ON_PIN #define PS_ON_PIN -1 // @@ -110,24 +110,24 @@ #define BTN_RT 32 // 'R' button - #undef BTN_ENC + #undef BTN_ENC #define BTN_ENC 31 // Disable encoder - #undef BTN_EN1 + #undef BTN_EN1 #define BTN_EN1 -1 - #undef BTN_EN2 + #undef BTN_EN2 #define BTN_EN2 -1 - #undef SD_DETECT_PIN + #undef SD_DETECT_PIN #define SD_DETECT_PIN 22 #elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) - #undef SD_DETECT_PIN + #undef SD_DETECT_PIN #define SD_DETECT_PIN 22 - #undef KILL_PIN + #undef KILL_PIN #define KILL_PIN 32 #endif diff --git a/Marlin/pins_RUMBA.h b/Marlin/pins_RUMBA.h index 376197c556..23a9c3ad10 100644 --- a/Marlin/pins_RUMBA.h +++ b/Marlin/pins_RUMBA.h @@ -100,7 +100,7 @@ #endif #if TEMP_SENSOR_2 == -1 - #define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_BED is defined as thermocouple) + #define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple) #else #define TEMP_2_PIN 13 // Analog Input (default connector for thermistor *T2* on rumba board is used) #endif @@ -109,7 +109,7 @@ //#define TEMP_X_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used) #if TEMP_SENSOR_BED == -1 - #define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_2 is defined as thermocouple) + #define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple) #else #define TEMP_BED_PIN 11 // Analog Input (default connector for thermistor *THB* on rumba board is used) #endif @@ -133,6 +133,7 @@ #define LED_PIN 13 #define PS_ON_PIN 45 #define KILL_PIN 46 +#define CASE_LIGHT_PIN 45 // // LCD / Controller @@ -148,3 +149,10 @@ #define BTN_EN1 11 #define BTN_EN2 12 #define BTN_ENC 43 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 14 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 15 diff --git a/Marlin/pins_SANGUINOLOLU_11.h b/Marlin/pins_SANGUINOLOLU_11.h index 62d92b61e8..6bac9d7a8a 100644 --- a/Marlin/pins_SANGUINOLOLU_11.h +++ b/Marlin/pins_SANGUINOLOLU_11.h @@ -24,6 +24,33 @@ * Sanguinololu board pin assignments */ +/** + * Rev B 26 DEC 2016 + * + * 1) added pointer to a current Arduino IDE extension + * 2) added support for M3, M4 & M5 spindle control commands + * 3) added case light pin definition + * + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu." #endif @@ -96,19 +123,26 @@ // // Misc. Functions // + /** - * On some broken versions of the Sanguino libraries the pin definitions are wrong, - * which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368. + * In some versions of the Sanguino libraries the pin + * definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi). + * If you encounter issues with these pins, upgrade your + * Sanguino libraries! See #368. */ //#define SDSS 24 #define SDSS 31 #if IS_MELZI - #define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368. + #define LED_PIN 27 #elif MB(STB_11) #define LCD_BACKLIGHT_PIN 17 // LCD backlight LED #endif +#if DISABLED(SPINDLE_LASER_ENABLE) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header + #define CASE_LIGHT_PIN 4 // MUST BE HARDWARE PWM - see if IO Header is available +#endif + // // LCD / Controller // @@ -181,14 +215,62 @@ #else #define BTN_ENC 30 #endif - #elif ENABLED(OLED_PANEL_TINYBOY2) - #define BTN_ENC 28 - #define LCD_SDSS -1 - #else // !Panelolu2, !TinyBoy2 + #else // !Panelolu2 #define BTN_ENC 16 #define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi - #endif // !Panelolu2, !TinyBoy2 + #endif // !Panelolu2 #define SD_DETECT_PIN -1 #endif // ULTRA_LCD && NEWPANEL + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) + #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header + + #define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN 11 + + #elif !MB(MELZI) // use X stepper motor socket + + /** + * To control the spindle speed and have an LCD you must sacrifice + * the Extruder and pull some signals off the X stepper driver socket. + * + * The following assumes: + * - The X stepper driver socket is empty + * - The extruder driver socket has a driver board plugged into it + * - The X stepper wires are attached the the extruder connector + */ + + /** + * Where to get the spindle signals + * + * spindle signal socket name socket name + * ------- + * /ENABLE O| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_LASER_PWM_PIN STEP O| |O VDD + * SPINDLE_LASER_ENABLE_PIN DIR O| |O GND + * ------- + * + * Note: Socket names vary from vendor to vendor. + */ + #undef X_DIR_PIN + #undef X_ENABLE_PIN + #undef X_STEP_PIN + #define X_DIR_PIN 0 + #define X_ENABLE_PIN 14 + #define X_STEP_PIN 1 + #define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 21 // Pin should have a pullup! + #define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin + #endif +#endif // SPINDLE_LASER_ENABLE diff --git a/Marlin/pins_SAV_MKI.h b/Marlin/pins_SAV_MKI.h index 019139d1e2..2048af9251 100644 --- a/Marlin/pins_SAV_MKI.h +++ b/Marlin/pins_SAV_MKI.h @@ -115,7 +115,6 @@ #define EXT_AUX_A4 4 // Analog #define EXT_AUX_A4_IO 44 // Digital IO, 42 (teensy), 44 (marlin) - // // LCD / Controller // @@ -134,10 +133,23 @@ #endif // SAV_3DLCD #if ENABLED(SAV_3DLCD) || ENABLED(SAV_3DGLCD) + #define BTN_EN1 EXT_AUX_A1_IO #define BTN_EN2 EXT_AUX_A0_IO #define BTN_ENC EXT_AUX_PWM_D24 #define KILL_PIN EXT_AUX_A2_IO #define HOME_PIN EXT_AUX_A4_IO -#endif // SAV_3DLCD || SAV_3DGLCD + +#else // Try to use the expansion header for spindle control + + // + // M3/M4/M5 - Spindle/Laser Control + // + #define SPINDLE_LASER_PWM_PIN 24 // 12 AT90USB… pin # + #define SPINDLE_LASER_ENABLE_PIN 39 // Pin should have a pullup! 41 AT90USB… pin # + #define SPINDLE_DIR_PIN 40 // 42 AT90USB… pin # + + #define CASE_LIGHT_PIN 0 // 24 AT90USB… pin # + +#endif diff --git a/Marlin/pins_SETHI.h b/Marlin/pins_SETHI.h index 12521f40a1..a05bb9eb27 100644 --- a/Marlin/pins_SETHI.h +++ b/Marlin/pins_SETHI.h @@ -24,6 +24,31 @@ * Sethi 3D_1 pin assignments - www.sethi3d.com.br */ +/** + * Rev B 26 DEC 2016 + * + * added pointer to a current Arduino IDE extension + * this assumes that this board uses the Sanguino pin map + */ + +/** + * A useable Arduino IDE extension (board manager) can be found at + * https://github.com/Lauszus/Sanguino + * + * This extension has been tested on Arduino 1.6.12 & 1.8.0 + * + * Here's the JSON path: + * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json + * + * When installing select 1.0.2 + * + * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino + * Just use the above JSON URL instead of Sparkfun's JSON. + * + * Once installed select the Sanguino board and then select the CPU. + * + */ + #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) #error "Oops! Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu." #endif diff --git a/Marlin/pins_TEENSY2.h b/Marlin/pins_TEENSY2.h index b7cf484be3..971de27e8b 100644 --- a/Marlin/pins_TEENSY2.h +++ b/Marlin/pins_TEENSY2.h @@ -124,6 +124,7 @@ #define SDSS 20 // 8 #define LED_PIN 6 #define PS_ON_PIN 27 +#define CASE_LIGHT_PIN 1 // MUST BE HARDWARE PWM // // LCD / Controller @@ -139,3 +140,10 @@ #define BTN_EN2 39 #define BTN_ENC 40 #endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 0 // MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 7 diff --git a/Marlin/pins_TEENSYLU.h b/Marlin/pins_TEENSYLU.h index b0fc8aec5f..d845e312e3 100644 --- a/Marlin/pins_TEENSYLU.h +++ b/Marlin/pins_TEENSYLU.h @@ -12,27 +12,82 @@ * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License - * along with this program. If not, see . + * along with this program. If not, see . * */ /** - * Teensylu 0.7 pin assignments (AT90USB1286) - * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! - * http://www.pjrc.com/teensy/teensyduino.html - * See http://reprap.org/wiki/Printrboard for more info + * rev B 30 DEC 2016 + * + * The original version of this file did NOT result in a useful program because: + * 1. The pin numbers assumed that the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line + * in FASTIO.h was commented out. There wasn't an Arduino IDE 1.6.x extension/package + * that supported this pin map so the latest Marlin wouldn't compile. + * 2. The silkscreen for the four end stops don't agree with the schematic. Activating + * the X endstop would tell the software that the Y endstop just went active. + * 3. The thermistor inputs also had heater names assigned to them. The result was + * thermistor inputs that were set to digital outputs. + * + * Rev B corrects the above problems by: + * 1. The "Marlin_AT90USB" extension/package was developed. This extension enables the + * latest Marlin software to compile using Arduino IDE 1.6.x and 1.80. + * 2. The endstop pin numbers in this file were changed to match the silkscreen. This + * makes it a little confusing when trying to correlate the schematic with the pin + * numbers used in this file. + * 3. The offending heater names were deleted. + * + * To create a useable image for Teensylu do the following: + * a) Install the Marlin_AT90USB extension with either of the following methods: + * Automatic - paste this URL into preferences and then use Boards manager + * https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json + * Manual: + * 1. Copy the following URL into Go to "https://github.com/Bob-the-Kuhn/Marlin_AT90USB", + * click on the "Clone or Download" button and then click on "Download ZIP" button. + * 2. Unzip the file, find the "Marlin_AT90USB" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably be + * located in a path similar to this: C:\Program Files (x86)\Arduino\hardware + * b) Connect the USBtinyISP to the board. + * c) In the Arduino IDE select the "AT90USB1286_STANDARD" board in the of the "Marlin_AT90USB" + * section and select the "USBtinyISP" programmer. + * d) In the Arduino IDE click on "burn bootloader". Don't worry about the "verify + * failed at 1F000" error message. + * e) The USBtinyISP programmer is no longer needed. Remove it. + * f) In FASTIO.h comment out the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line. + * g) To upload a sketch do the following: + * 1. remove the jumper + * 2. press reset + * 3. click on the "upload" button in the Arduino IDE + * 4. wait until the upload finishes (less than a minute) + * 5. put the jumper back on + * 6. press the reset button + * + * + * NOTE - the "Marlin_AT90USB" pin maps make PWM0A available rather than the usual PWM1C. + * These PWMs share the same physical pin. Marlin uses TIMER1 to generate + * interrupts and sets it up such that PWM1A, PWM1B & PWM1C can not be used. */ -#ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." + /** + * SILKSCREEN ERROR + * + * The silkscreen for the endstops do NOT match the schematic. The silkscreen SHOULD + * read (from left to right) X-STOP, Y-STOP, Z-STOP & E-STOP. The silkscreen actually + * reads E-STOP, X-STOP, Y-STOP & Z-STOP. + * + * The pin assignments in this file match the silkscreen. + */ + + +#if !defined(__AVR_AT90USB1286__) && !defined(__AVR_AT90USB1286P__) + #error "Oops! Make sure you have 'AT90USB1286_STANDARD' selected from the 'Tools -> Boards' menu." #endif -#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional. - #error "These Teensylu assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h" +#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) + #error "please disable (comment out) the AT90USBxx_TEENSYPP_ASSIGNMENTS flag in FASTIO.h " #endif #define BOARD_NAME "Teensylu" @@ -40,74 +95,84 @@ #define USBCON 1286 // Disable MarlinSerial etc. #define LARGE_FLASH true + +// +// Limit Switche definitions that match the SCHEMATIC +// +//#define X_STOP_PIN 13 +//#define Y_STOP_PIN 14 +//#define Z_STOP_PIN 15 +//#define E_STOP_PIN 36 + + // -// Limit Switches +// Limit Switch definitions that match the SILKSCREEN // -#define X_STOP_PIN 13 -#define Y_STOP_PIN 14 -#define Z_STOP_PIN 15 +#define X_STOP_PIN 14 +#define Y_STOP_PIN 15 +#define Z_STOP_PIN 36 +//#define E_STOP_PIN 13 // // Steppers // -#define X_STEP_PIN 0 -#define X_DIR_PIN 1 -#define X_ENABLE_PIN 39 +#define X_STEP_PIN 0 +#define X_DIR_PIN 1 +#define X_ENABLE_PIN 39 -#define Y_STEP_PIN 2 -#define Y_DIR_PIN 3 -#define Y_ENABLE_PIN 38 +#define Y_STEP_PIN 2 +#define Y_DIR_PIN 3 +#define Y_ENABLE_PIN 38 -#define Z_STEP_PIN 4 -#define Z_DIR_PIN 5 -#define Z_ENABLE_PIN 23 +#define Z_STEP_PIN 4 +#define Z_DIR_PIN 5 +#define Z_ENABLE_PIN 23 + +#define E0_STEP_PIN 6 +#define E0_DIR_PIN 7 +#define E0_ENABLE_PIN 19 -#define E0_STEP_PIN 6 -#define E0_DIR_PIN 7 -#define E0_ENABLE_PIN 19 -// // Temperature Sensors -// -#define TEMP_0_PIN 7 // Analog Input (Extruder) -#define TEMP_BED_PIN 6 // Analog Input (Bed) + +#define TEMP_0_PIN 7 // Analog Input (Extruder) +#define TEMP_BED_PIN 6 // Analog Input (Bed) // // Heaters / Fans // -#define HEATER_0_PIN 21 // Extruder -#define HEATER_1_PIN 46 -#define HEATER_2_PIN 47 -#define HEATER_BED_PIN 20 - -// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin -// fastio pin numbering otherwise -#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN) - #define FAN_PIN 22 -#else - #define FAN_PIN 16 -#endif +#define HEATER_0_PIN 21 // Extruder +#define HEATER_BED_PIN 20 + +#define FAN_PIN 22 // // Misc. Functions // -#define SDSS 8 +#define SDSS 8 +#define CASE_LIGHT_PIN 24 // // LCD / Controller // #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) - #define BEEPER_PIN -1 + #define BEEPER_PIN -1 #if ENABLED(LCD_I2C_PANELOLU2) - #define BTN_EN1 27 // RX1 - fastio.h pin mapping 27 - #define BTN_EN2 26 // TX1 - fastio.h pin mapping 26 - #define BTN_ENC 43 // A3 - fastio.h pin mapping 43 - #define SDSS 40 // use SD card on Panelolu2 (Teensyduino pin mapping) + #define BTN_EN1 27 + #define BTN_EN2 26 + #define BTN_ENC 43 + #define SDSS 40 // use SD card on Panelolu2 #endif // LCD_I2C_PANELOLU2 - #define SD_DETECT_PIN -1 + #define SD_DETECT_PIN -1 #endif // ULTRA_LCD && NEWPANEL +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 42 diff --git a/Marlin/pins_ULTIMAIN_2.h b/Marlin/pins_ULTIMAIN_2.h index 731f6f88fe..d4b99fafc7 100644 --- a/Marlin/pins_ULTIMAIN_2.h +++ b/Marlin/pins_ULTIMAIN_2.h @@ -24,6 +24,14 @@ * Ultiboard v2.0 pin assignments */ +/** + * Rev B 2 JAN 2017 + * + * Added pin definitions for: + * M3, M4 & M5 spindle control commands + * case light + */ + #ifndef __AVR_ATmega2560__ #error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu." #endif @@ -110,3 +118,16 @@ #define BTN_EN1 40 #define BTN_EN2 41 #define BTN_ENC 19 + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) // use the LED_PIN for spindle speed control or case light + #undef LED_PIN + #define SPINDLE_DIR_PIN 16 + #define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 8 // MUST BE HARDWARE PWM +#else + #undef LED_PIN + #define CASE_LIGHT_PIN 8 +#endif diff --git a/Marlin/pins_ULTIMAKER.h b/Marlin/pins_ULTIMAKER.h index 4b4b31ad8c..cb11768071 100644 --- a/Marlin/pins_ULTIMAKER.h +++ b/Marlin/pins_ULTIMAKER.h @@ -24,6 +24,14 @@ * Ultimaker pin assignments */ +/** + * Rev B 2 JAN 2017 + * + * Added pin definitions for: + * M3, M4 & M5 spindle control commands + * case light + */ + #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif @@ -102,6 +110,7 @@ #define LED_PIN 13 #define PS_ON_PIN 12 #define SUICIDE_PIN 54 // PIN that has to be turned on right after start, to keep power flowing. +#define CASE_LIGHT_PIN 8 // // LCD / Controller @@ -146,3 +155,10 @@ #endif // !NEWPANEL #endif // ULTRA_LCD + +// +// M3/M4/M5 - Spindle/Laser Control +// +#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup! +#define SPINDLE_DIR_PIN 11 // use the EXP3 PWM header diff --git a/Marlin/pins_ULTIMAKER_OLD.h b/Marlin/pins_ULTIMAKER_OLD.h index b42ba69585..5dafda2d39 100644 --- a/Marlin/pins_ULTIMAKER_OLD.h +++ b/Marlin/pins_ULTIMAKER_OLD.h @@ -24,6 +24,42 @@ * Ultimaker pin assignments (Old electronics) */ + /** + * Rev B 3 JAN 2017 + * + * Details on pin definitions for M3, M4 & M5 spindle control commands and for + * the CASE_LIGHT_PIN are at the end of this file. + * + * This started out as an attempt to add pin definitions for M3, M4 & M5 spindle + * control commands but quickly turned into a head scratcher as the sources for + * the revisions provided inconsistent information. + * + * As best I can determine: + * 1.5.3 boards should use the pins_ULTIMAKER.h file which means the BOARD_NAME + * define in this file should say 1.5.3 rather than 1.5.4 + * This file is meant for 1.1 - 1.3 boards. + * The endstops for the 1.0 boards use different definitions than on the 1.1 - 1.3 + * boards. + * + * I've added sections that have the 1.0 and 1.5.3 + endstop definitions so you can + * easily switch if needed. I've also copied over the 1.5.3 + LCD definitions. + * + * To be 100% sure of the board you have: + * 1. In Configuration_adv.h enable "PINS_DEBUGGING" + * 2. Compile & uploade + * 3. Enter the command "M43 W1 I1". This command will report that pin nmumber and + * name of any pin that changes state. + * 4. Using a 1k (approximately) resistor pull the endstops and some of the LCD pins + * to ground and see what is reported. + * 5. If the reported pin doesn't match the file then try a different board revision + * and repeat steps 2 - 5 + */ + +#define board_rev_1_1_TO_1_3 +//#define board_rev_1_0 +//#define board_rev_1_5 + + #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif @@ -37,18 +73,38 @@ // // Limit Switches // -#define X_MIN_PIN 15 -#define X_MAX_PIN 14 -#define Y_MIN_PIN 17 -#define Y_MAX_PIN 16 -#define Z_MIN_PIN 19 -#define Z_MAX_PIN 18 +#if ENABLED(board_rev_1_1_TO_1_3) + #define X_MIN_PIN 15 // SW1 + #define X_MAX_PIN 14 // SW2 + #define Y_MIN_PIN 17 // SW3 + #define Y_MAX_PIN 16 // SW4 + #define Z_MIN_PIN 19 // SW5 + #define Z_MAX_PIN 18 // SW6 +#endif + +#if ENABLED(board_rev_1_0) + #define X_MIN_PIN 13 // SW1 + #define X_MAX_PIN 12 // SW2 + #define Y_MIN_PIN 11 // SW3 + #define Y_MAX_PIN 10 // SW4 + #define Z_MIN_PIN 9 // SW5 + #define Z_MAX_PIN 8 // SW6 +#endif + +#if ENABLED(board_rev_1_5) + #define X_MIN_PIN 22 + #define X_MAX_PIN 24 + #define Y_MIN_PIN 26 + #define Y_MAX_PIN 28 + #define Z_MIN_PIN 30 + #define Z_MAX_PIN 32 +#endif // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN - #define Z_MIN_PROBE_PIN 18 + #define Z_MIN_PROBE_PIN Z_MAX_PIN #endif // @@ -70,9 +126,9 @@ #define E0_DIR_PIN 45 #define E0_ENABLE_PIN 41 -#define E1_STEP_PIN -1 -#define E1_DIR_PIN -1 -#define E1_ENABLE_PIN -1 +#define E1_STEP_PIN -1 // 49 +#define E1_DIR_PIN -1 // 47 +#define E1_ENABLE_PIN -1 // 48 // // Temperature Sensors @@ -84,14 +140,144 @@ // Heaters / Fans // #define HEATER_0_PIN 2 -#define HEATER_1_PIN 1 +//#define HEATER_1_PIN 3 // used for case light Rev A said "1" +#define HEATER_BED_PIN 4 // // LCD / Controller // -#define LCD_PINS_RS 24 -#define LCD_PINS_ENABLE 22 -#define LCD_PINS_D4 36 -#define LCD_PINS_D5 34 -#define LCD_PINS_D6 32 -#define LCD_PINS_D7 30 +#if ENABLED(board_rev_1_0) || ENABLED(board_rev_1_1_TO_1_3) + #define LCD_PINS_RS 24 + #define LCD_PINS_ENABLE 22 + #define LCD_PINS_D4 36 + #define LCD_PINS_D5 34 + #define LCD_PINS_D6 32 + #define LCD_PINS_D7 30 +#elif ENABLED(board_rev_1_5) && ENABLED(ULTRA_LCD) + + #define BEEPER_PIN 18 + + #if ENABLED(NEWPANEL) + + #define LCD_PINS_RS 20 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 16 + #define LCD_PINS_D5 21 + #define LCD_PINS_D6 5 + #define LCD_PINS_D7 6 + + // buttons are directly attached + #define BTN_EN1 40 + #define BTN_EN2 42 + #define BTN_ENC 19 + + #define SD_DETECT_PIN 38 + + #else // !NEWPANEL - Old style panel with shift register + + // buttons are attached to a shift register + #define SHIFT_CLK 38 + #define SHIFT_LD 42 + #define SHIFT_OUT 40 + #define SHIFT_EN 17 + + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 5 + #define LCD_PINS_D4 6 + #define LCD_PINS_D5 21 + #define LCD_PINS_D6 20 + #define LCD_PINS_D7 19 + + #define SD_DETECT_PIN -1 + + #endif // !NEWPANEL + +#endif // ULTRA_LCD + +// +// case light - see spindle section for more info on available hardware PWMs +// +#if !PIN_EXISTS(CASE_LIGHT) && ENABLED(board_rev_1_5) + #define CASE_LIGHT_PIN 7 // use PWM - MUST BE HARDWARE PWM +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) + + #if ENABLED(board_rev_1_0) // use the last three SW positions + + #undef Z_MIN_PROBE_PIN + #undef X_MIN_PIN // SW1 + #undef X_MAX_PIN // SW2 + #undef Y_MIN_PIN // SW3 + #undef Y_MAX_PIN // SW4 + #undef Z_MIN_PIN // SW5 + #undef Z_MAX_PIN // SW6 + + #define X_STOP_PIN 13 // SW1 (didn't change) - also has a useable hardware PWM + #define Y_STOP_PIN 12 // SW2 + #define Z_STOP_PIN 11 // SW3 + + #define SPINDLE_DIR_PIN 10 // SW4 + #define SPINDLE_LASER_PWM_PIN 9 // SW5 MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 8 // SW6 Pin should have a pullup! + + #elif ENABLED(board_rev_1_5) // use the same pins - but now they are on a different connector + + #define SPINDLE_DIR_PIN 10 // EXP3-6 (silkscreen says 10) + #define SPINDLE_LASER_PWM_PIN 9 // EXP3-7 (silkscreen says 9) MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 8 // EXP3-8 (silkscreen says 8) Pin should have a pullup! + + #elif ENABLED(board_rev_1_1_TO_1_3) + + /** + * Only four hardware PWMs physically connected to anything on these boards: + * + * HEATER_0_PIN 2 silkscreen varies - usually "PWM 1" or "HEATER1" + * HEATER_1_PIN 3 silkscreen varies - usually "PWM 2" or "HEATER2" + * HEATER_BED_PIN 4 silkscreen varies - usually "PWM 3" or "HEATED BED" + * E0_DIR_PIN 45 + * + * If one of the heaters is used then special precautions will usually be needed. + * They have an LED and resistor pullup to +24V which could damage 3.3V-5V ICs. + */ + #if EXTRUDERS == 1 // Move E0 stepper module to the spare and get signals from E0 + #undef E0_STEP_PIN + #undef E0_DIR_PIN + #undef E0_ENABLE_PIN + #define E0_STEP_PIN 49 + #define E0_DIR_PIN 47 + #define E0_ENABLE_PIN 48 + #define SPINDLE_DIR_PIN 43 + #define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup! + #elif TEMP_SENSOR_BED == 0 // Can't use E0 so see if HEATER_BED_PIN is available + #undef HEATER_BED_PIN + #define SPINDLE_DIR_PIN 38 // Probably pin 4 on 10 pin connector closest to the E0 socket + #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM - Special precautions usually needed. + #define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup! (Probably pin 6 on the 10-pin + // connector closest to the E0 socket) + #endif + #endif +#endif + +/** + * Where to get the spindle signals on the E0 socket + * + * spindle signal socket name socket name + * ------- + * SPINDLE_LASER_ENABLE_PIN /ENABLE *| |O VMOT + * MS1 O| |O GND + * MS2 O| |O 2B + * MS3 O| |O 2A + * /RESET O| |O 1A + * /SLEEP O| |O 1B + * SPINDLE_DIR_PIN STEP O| |O VDD + * SPINDLE_LASER_PWM_PIN DIR O| |O GND + * ------- + * * - pin closest to MS1, MS2 & MS3 jumpers on the board + * + * Note: Socket names vary from vendor to vendor. + */