Browse Source

Improve Malyan M200 integration (#15462)

pull/1/head
Me No Dev 5 years ago
committed by Scott Lahteine
parent
commit
fc6a0937b8
  1. 91
      Marlin/src/lcd/extui_malyan_lcd.cpp
  2. 16
      Marlin/src/pins/stm32/pins_MALYAN_M200.h
  3. 37
      config/examples/Malyan/M200/Configuration.h
  4. 8
      config/examples/Malyan/M200/Configuration_adv.h

91
Marlin/src/lcd/extui_malyan_lcd.cpp

@ -117,17 +117,27 @@ void write_to_lcd(const char * const message) {
* the command portion begins after the : * the command portion begins after the :
*/ */
void process_lcd_c_command(const char* command) { void process_lcd_c_command(const char* command) {
const int target_val = command[1] ? atoi(command + 1) : -1;
if (target_val < 0) {
DEBUG_ECHOLNPAIR("UNKNOWN C COMMAND ", command);
return;
}
switch (command[0]) { switch (command[0]) {
case 'C': // Cope with both V1 early rev and later LCDs. case 'C': // Cope with both V1 early rev and later LCDs.
case 'S': case 'S':
feedrate_percentage = atoi(command + 1) * 10; feedrate_percentage = target_val * 10;
LIMIT(feedrate_percentage, 10, 999); LIMIT(feedrate_percentage, 10, 999);
break; break;
case 'T': ExtUI::setTargetTemp_celsius(atoi(command + 1), ExtUI::extruder_t::E0); break; case 'T':
// Sometimes the LCD will send commands to turn off both extruder and bed, though
// this should not happen since the printing screen is up. Better safe than sorry.
if (!print_job_timer.isRunning() || target_val > 0)
ExtUI::setTargetTemp_celsius(target_val, ExtUI::extruder_t::E0);
break;
#if HAS_HEATED_BED #if HAS_HEATED_BED
case 'P': ExtUI::setTargetTemp_celsius(atoi(command + 1), ExtUI::heater_t::BED); break; case 'P': ExtUI::setTargetTemp_celsius(target_val, ExtUI::heater_t::BED); break;
#endif #endif
default: DEBUG_ECHOLNPAIR("UNKNOWN C COMMAND ", command); default: DEBUG_ECHOLNPAIR("UNKNOWN C COMMAND ", command);
@ -143,6 +153,7 @@ void process_lcd_c_command(const char* command) {
*/ */
void process_lcd_eb_command(const char* command) { void process_lcd_eb_command(const char* command) {
char elapsed_buffer[10]; char elapsed_buffer[10];
static uint8_t iteration = 0;
duration_t elapsed; duration_t elapsed;
switch (command[0]) { switch (command[0]) {
case '0': { case '0': {
@ -150,6 +161,13 @@ void process_lcd_eb_command(const char* command) {
sprintf_P(elapsed_buffer, PSTR("%02u%02u%02u"), uint16_t(elapsed.hour()), uint16_t(elapsed.minute()) % 60, uint16_t(elapsed.second()) % 60); sprintf_P(elapsed_buffer, PSTR("%02u%02u%02u"), uint16_t(elapsed.hour()), uint16_t(elapsed.minute()) % 60, uint16_t(elapsed.second()) % 60);
char message_buffer[MAX_CURLY_COMMAND]; char message_buffer[MAX_CURLY_COMMAND];
uint8_t done_pct = print_job_timer.isRunning() ? (iteration * 10) : 100;
iteration = (iteration + 1) % 10; // Provide progress animation
#if ENABLED(SDSUPPORT)
if (ExtUI::isPrintingFromMedia() || ExtUI::isPrintingFromMediaPaused())
done_pct = card.percentDone();
#endif
sprintf_P(message_buffer, sprintf_P(message_buffer,
PSTR("{T0:%03i/%03i}{T1:000/000}{TP:%03i/%03i}{TQ:%03i}{TT:%s}"), PSTR("{T0:%03i/%03i}{T1:000/000}{TP:%03i/%03i}{TQ:%03i}{TT:%s}"),
int(thermalManager.degHotend(0)), thermalManager.degTargetHotend(0), int(thermalManager.degHotend(0)), thermalManager.degTargetHotend(0),
@ -159,7 +177,7 @@ void process_lcd_eb_command(const char* command) {
0, 0, 0, 0,
#endif #endif
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
card.percentDone(), done_pct,
#else #else
0, 0,
#endif #endif
@ -186,7 +204,7 @@ void process_lcd_j_command(const char* command) {
auto move_axis = [command](const auto axis) { auto move_axis = [command](const auto axis) {
const float dist = atof(command + 1) / 10.0; const float dist = atof(command + 1) / 10.0;
ExtUI::setAxisPosition_mm(ExtUI::getAxisPosition_mm(axis) + dist, axis); ExtUI::setAxisPosition_mm(ExtUI::getAxisPosition_mm(axis) + dist, axis);
} };
switch (command[0]) { switch (command[0]) {
case 'E': break; case 'E': break;
@ -330,7 +348,6 @@ void process_lcd_s_command(const char* command) {
void process_lcd_command(const char* command) { void process_lcd_command(const char* command) {
const char *current = command; const char *current = command;
current++; // skip the leading {. The trailing one is already gone.
byte command_code = *current++; byte command_code = *current++;
if (*current == ':') { if (*current == ':') {
@ -350,6 +367,31 @@ void process_lcd_command(const char* command) {
DEBUG_ECHOLNPAIR("UNKNOWN COMMAND FORMAT ", command); DEBUG_ECHOLNPAIR("UNKNOWN COMMAND FORMAT ", command);
} }
// Parse LCD commands mixed with G-Code
void parse_lcd_byte(byte b) {
static bool parsing_lcd_cmd = false;
static char inbound_buffer[MAX_CURLY_COMMAND];
if (!parsing_lcd_cmd) {
if (b == '{' || b == '\n' || b == '\r') { // A line-ending or opening brace
parsing_lcd_cmd = b == '{'; // Brace opens an LCD command
if (inbound_count) { // Looks like a G-code is in the buffer
inbound_buffer[inbound_count] = '\0'; // Reset before processing
inbound_count = 0;
queue.enqueue_one_now(inbound_buffer); // Handle the G-code command
}
}
}
else if (b == '}') { // Closing brace on an LCD command
parsing_lcd_cmd = false; // Unflag and...
inbound_buffer[inbound_count] = '\0'; // reset before processing
inbound_count = 0;
process_lcd_command(inbound_buffer); // Handle the LCD command
}
else if (inbound_count < MAX_CURLY_COMMAND - 2)
inbound_buffer[inbound_count++] = b; // Buffer only if space remains
}
/** /**
* UC means connected. * UC means connected.
* UD means disconnected * UD means disconnected
@ -360,8 +402,8 @@ void update_usb_status(const bool forceUpdate) {
// This is mildly different than stock, which // This is mildly different than stock, which
// appears to use the usb discovery status. // appears to use the usb discovery status.
// This is more logical. // This is more logical.
if (last_usb_connected_status != Serial || forceUpdate) { if (last_usb_connected_status != SerialUSB || forceUpdate) {
last_usb_connected_status = Serial; last_usb_connected_status = SerialUSB;
write_to_lcd_P(last_usb_connected_status ? PSTR("{R:UC}\r\n") : PSTR("{R:UD}\r\n")); write_to_lcd_P(last_usb_connected_status ? PSTR("{R:UC}\r\n") : PSTR("{R:UD}\r\n"));
} }
} }
@ -391,24 +433,14 @@ namespace ExtUI {
/** /**
* - from printer on startup: * - from printer on startup:
* {SYS:STARTED}{VER:29}{SYS:STARTED}{R:UD} * {SYS:STARTED}{VER:29}{SYS:STARTED}{R:UD}
* The optimize attribute fixes a register Compile
* error for amtel.
*/ */
static char inbound_buffer[MAX_CURLY_COMMAND];
// First report USB status. // First report USB status.
update_usb_status(false); update_usb_status(false);
// now drain commands... // now drain commands...
while (LCD_SERIAL.available()) { while (LCD_SERIAL.available()) {
const byte b = (byte)LCD_SERIAL.read() & 0x7F; parse_lcd_byte((byte)LCD_SERIAL.read() & 0x7F);
inbound_buffer[inbound_count++] = b;
if (b == '}' || inbound_count == sizeof(inbound_buffer) - 1) {
inbound_buffer[inbound_count - 1] = '\0';
process_lcd_command(inbound_buffer);
inbound_count = 0;
inbound_buffer[0] = 0;
}
} }
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
@ -438,22 +470,23 @@ namespace ExtUI {
write_to_lcd_P("}"); write_to_lcd_P("}");
} }
void onPrintTimerStarted() { write_to_lcd_P(PSTR("{SYS:BUILD}")); }
void onPrintTimerPaused() {}
void onPrintTimerStopped() { write_to_lcd_P(PSTR("{TQ:100}")); }
// Not needed for Malyan LCD // Not needed for Malyan LCD
void onStatusChanged(const char * const msg) { UNUSED(msg); } void onStatusChanged(const char * const) {}
void onMediaInserted() {}; void onMediaInserted() {};
void onMediaError() {}; void onMediaError() {};
void onMediaRemoved() {}; void onMediaRemoved() {};
void onPlayTone(const uint16_t frequency, const uint16_t duration) { UNUSED(frequency); UNUSED(duration); } void onPlayTone(const uint16_t, const uint16_t) {}
void onPrintTimerStarted() {}
void onPrintTimerPaused() {}
void onPrintTimerStopped() {}
void onFilamentRunout(const extruder_t extruder) {} void onFilamentRunout(const extruder_t extruder) {}
void onUserConfirmRequired(const char * const msg) { UNUSED(msg); } void onUserConfirmRequired(const char * const) {}
void onFactoryReset() {} void onFactoryReset() {}
void onStoreSettings(char *buff) { UNUSED(buff); } void onStoreSettings(char*) {}
void onLoadSettings(const char *buff) { UNUSED(buff); } void onLoadSettings(const char*) {}
void onConfigurationStoreWritten(bool success) { UNUSED(success); } void onConfigurationStoreWritten(bool) {}
void onConfigurationStoreRead(bool success) { UNUSED(success); } void onConfigurationStoreRead(bool) {}
} }
#endif // MALYAN_LCD #endif // MALYAN_LCD

16
Marlin/src/pins/stm32/pins_MALYAN_M200.h

@ -42,6 +42,8 @@
// On STM32F103: // On STM32F103:
// PB3, PB6, PB7, and PB8 can be used with pwm, which rules out TIM2 and TIM4. // PB3, PB6, PB7, and PB8 can be used with pwm, which rules out TIM2 and TIM4.
// On STM32F070, 16 and 17 are in use, but 1 and 3 are available. // On STM32F070, 16 and 17 are in use, but 1 and 3 are available.
#undef STEP_TIMER
#undef TEMP_TIMER
#define STEP_TIMER 1 #define STEP_TIMER 1
#define TEMP_TIMER 3 #define TEMP_TIMER 3
@ -84,15 +86,7 @@
#define HEATER_0_PIN PB6 // HOTEND0 MOSFET #define HEATER_0_PIN PB6 // HOTEND0 MOSFET
#define HEATER_BED_PIN PB7 // BED MOSFET #define HEATER_BED_PIN PB7 // BED MOSFET
// FAN_PIN is commented out here because the M200 example #define MALYAN_FAN1_PIN PB8 // FAN1 header on board - PRINT FAN
// Configuration_adv.h does NOT override E0_AUTO_FAN_PIN. #define MALYAN_FAN2_PIN PB3 // FAN2 header on board - CONTROLLER FAN
#ifndef FAN_PIN
//#define FAN_PIN PB8 // FAN1 header on board - PRINT FAN
#endif
#define FAN1_PIN PB3 // FAN2 header on board - CONTROLLER FAN
#define FAN2_PIN -1 // FAN3 header on board - EXTRUDER0 FAN
// This board has only the controller fan and the extruder fan #define FAN1_PIN MALYAN_FAN2_PIN
// If someone hacks to put a direct power fan on the controller, PB3 could
// be used as a separate print cooling fan.
#define ORIG_E0_AUTO_FAN_PIN PB8

37
config/examples/Malyan/M200/Configuration.h

@ -146,7 +146,7 @@
#define EXTRUDERS 1 #define EXTRUDERS 1
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
// For Cyclops or any "multi-extruder" that shares a single nozzle. // For Cyclops or any "multi-extruder" that shares a single nozzle.
//#define SINGLENOZZLE //#define SINGLENOZZLE
@ -474,9 +474,10 @@
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// Ultimaker // Ultimaker
#define DEFAULT_Kp 26.15 //#define DEFAULT_Kp 26.15
#define DEFAULT_Ki 2.74 //#define DEFAULT_Ki 2.74
#define DEFAULT_Kd 62.35 //#define DEFAULT_Kd 62.35
// MakerGear // MakerGear
//#define DEFAULT_Kp 7.0 //#define DEFAULT_Kp 7.0
//#define DEFAULT_Ki 0.1 //#define DEFAULT_Ki 0.1
@ -487,6 +488,11 @@
//#define DEFAULT_Ki 2.25 //#define DEFAULT_Ki 2.25
//#define DEFAULT_Kd 440 //#define DEFAULT_Kd 440
// Malyan M200
#define DEFAULT_Kp 20.0
#define DEFAULT_Ki 2.02
#define DEFAULT_Kd 100.00
#endif // PIDTEMP #endif // PIDTEMP
//=========================================================================== //===========================================================================
@ -506,7 +512,7 @@
* heater. If your configuration is significantly different than this and you don't understand * heater. If your configuration is significantly different than this and you don't understand
* the issues involved, don't use bed PID until someone else verifies that your hardware works. * the issues involved, don't use bed PID until someone else verifies that your hardware works.
*/ */
//#define PIDTEMPBED #define PIDTEMPBED
//#define BED_LIMIT_SWITCHING //#define BED_LIMIT_SWITCHING
@ -524,9 +530,9 @@
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 231.09 //#define DEFAULT_bedKp 231.09
#define DEFAULT_bedKi 45.21 //#define DEFAULT_bedKi 45.21
#define DEFAULT_bedKd 295.34 //#define DEFAULT_bedKd 295.34
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
//from pidautotune //from pidautotune
@ -534,6 +540,11 @@
//#define DEFAULT_bedKi 1.41 //#define DEFAULT_bedKi 1.41
//#define DEFAULT_bedKd 1675.16 //#define DEFAULT_bedKd 1675.16
// Malyan M200
#define DEFAULT_bedKp 14.00
#define DEFAULT_bedKi 0.9
#define DEFAULT_bedKd 120.4
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#endif // PIDTEMPBED #endif // PIDTEMPBED
@ -1051,8 +1062,8 @@
// @section machine // @section machine
// The size of the print bed // The size of the print bed
#define X_BED_SIZE 200 #define X_BED_SIZE 120
#define Y_BED_SIZE 200 #define Y_BED_SIZE 120
// Travel limits (mm) after homing, corresponding to endstop positions. // Travel limits (mm) after homing, corresponding to endstop positions.
#define X_MIN_POS 0 #define X_MIN_POS 0
@ -1060,7 +1071,7 @@
#define Z_MIN_POS 0 #define Z_MIN_POS 0
#define X_MAX_POS X_BED_SIZE #define X_MAX_POS X_BED_SIZE
#define Y_MAX_POS Y_BED_SIZE #define Y_MAX_POS Y_BED_SIZE
#define Z_MAX_POS 200 #define Z_MAX_POS 120
/** /**
* Software Endstops * Software Endstops
@ -1278,7 +1289,7 @@
#endif #endif
// Add a menu item to move between bed corners for manual bed adjustment // Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS //#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS) #if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
@ -1627,7 +1638,7 @@
*/ */
//#define SPI_SPEED SPI_HALF_SPEED //#define SPI_SPEED SPI_HALF_SPEED
//#define SPI_SPEED SPI_QUARTER_SPEED //#define SPI_SPEED SPI_QUARTER_SPEED
#define SPI_SPEED SPI_EIGHTH_SPEED //#define SPI_SPEED SPI_EIGHTH_SPEED
/** /**
* SD CARD: ENABLE CRC * SD CARD: ENABLE CRC

8
config/examples/Malyan/M200/Configuration_adv.h

@ -277,9 +277,9 @@
* The fan will turn on automatically whenever any stepper is enabled * The fan will turn on automatically whenever any stepper is enabled
* and turn off after a set period after all steppers are turned off. * and turn off after a set period after all steppers are turned off.
*/ */
//#define USE_CONTROLLER_FAN #define USE_CONTROLLER_FAN // Malyan M200: uncomment if you use FAN2 to cool the board (original)
#if ENABLED(USE_CONTROLLER_FAN) #if ENABLED(USE_CONTROLLER_FAN)
//#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan #define CONTROLLER_FAN_PIN MALYAN_FAN2_PIN // Set a custom pin for the controller fan
#define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
#define CONTROLLERFAN_SPEED 255 // 255 == full speed #define CONTROLLERFAN_SPEED 255 // 255 == full speed
//#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled
@ -346,7 +346,9 @@
* Multiple extruders can be assigned to the same pin in which case * Multiple extruders can be assigned to the same pin in which case
* the fan will turn on when any selected extruder is above the threshold. * the fan will turn on when any selected extruder is above the threshold.
*/ */
//#define E0_AUTO_FAN_PIN -1 //#define FAN_PIN MALYAN_FAN1_PIN // Malyan M200: uncomment if you use FAN1 to cool the part and FAN2 to cool the extruder
//#define E0_AUTO_FAN_PIN MALYAN_FAN2_PIN // Malyan M200: uncomment if you use FAN1 to cool the part and FAN2 to cool the extruder
#define E0_AUTO_FAN_PIN MALYAN_FAN1_PIN // Malyan M200: uncomment if you use FAN1 to cool the extruder and the part (original)
#define E1_AUTO_FAN_PIN -1 #define E1_AUTO_FAN_PIN -1
#define E2_AUTO_FAN_PIN -1 #define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1 #define E3_AUTO_FAN_PIN -1

Loading…
Cancel
Save