Browse Source

software_endstops: use *_MIN_POS and *_MAX_POS for arcs

If [XYZ]_HOME_POS and [XYZ]_MIN_POS aren't 0, these corrections are
wrong.  Use the same logic as in Marlin.pde:prepare_move: ie, clamp to
[XYZ]_{MIN,MAX}_POS.

While we're here, put this cut-and-paste code in a function
clamp_to_software_endstops.

Signed-off-by: Ian Jackson <ijackson@chiark.greenend.org.uk>
pull/1/head
Ian Jackson 12 years ago
parent
commit
faccb35850
  1. 1
      Marlin/Marlin.h
  2. 20
      Marlin/Marlin.pde
  3. 12
      Marlin/motion_control.cpp

1
Marlin/Marlin.h

@ -169,6 +169,7 @@ bool IsStopped();
void enquecommand(const char *cmd); //put an ascii command at the end of the current buffer. void enquecommand(const char *cmd); //put an ascii command at the end of the current buffer.
void prepare_arc_move(char isclockwise); void prepare_arc_move(char isclockwise);
void clamp_to_software_endstops(float target[3]);
#ifdef FAST_PWM_FAN #ifdef FAST_PWM_FAN
void setPwmFrequency(uint8_t pin, int val); void setPwmFrequency(uint8_t pin, int val);

20
Marlin/Marlin.pde

@ -1541,19 +1541,25 @@ void get_arc_coordinates()
} }
} }
void prepare_move() void clamp_to_software_endstops(float target[3])
{ {
if (min_software_endstops) { if (min_software_endstops) {
if (destination[X_AXIS] < X_MIN_POS) destination[X_AXIS] = X_MIN_POS; if (target[X_AXIS] < X_MIN_POS) target[X_AXIS] = X_MIN_POS;
if (destination[Y_AXIS] < Y_MIN_POS) destination[Y_AXIS] = Y_MIN_POS; if (target[Y_AXIS] < Y_MIN_POS) target[Y_AXIS] = Y_MIN_POS;
if (destination[Z_AXIS] < Z_MIN_POS) destination[Z_AXIS] = Z_MIN_POS; if (target[Z_AXIS] < Z_MIN_POS) target[Z_AXIS] = Z_MIN_POS;
} }
if (max_software_endstops) { if (max_software_endstops) {
if (destination[X_AXIS] > X_MAX_POS) destination[X_AXIS] = X_MAX_POS; if (target[X_AXIS] > X_MAX_POS) target[X_AXIS] = X_MAX_POS;
if (destination[Y_AXIS] > Y_MAX_POS) destination[Y_AXIS] = Y_MAX_POS; if (target[Y_AXIS] > Y_MAX_POS) target[Y_AXIS] = Y_MAX_POS;
if (destination[Z_AXIS] > Z_MAX_POS) destination[Z_AXIS] = Z_MAX_POS; if (target[Z_AXIS] > Z_MAX_POS) target[Z_AXIS] = Z_MAX_POS;
} }
}
void prepare_move()
{
clamp_to_software_endstops(destination);
previous_millis_cmd = millis(); previous_millis_cmd = millis();
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate*feedmultiply/60/100.0, active_extruder); plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate*feedmultiply/60/100.0, active_extruder);
for(int8_t i=0; i < NUM_AXIS; i++) { for(int8_t i=0; i < NUM_AXIS; i++) {

12
Marlin/motion_control.cpp

@ -125,17 +125,7 @@ void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8
arc_target[axis_linear] += linear_per_segment; arc_target[axis_linear] += linear_per_segment;
arc_target[E_AXIS] += extruder_per_segment; arc_target[E_AXIS] += extruder_per_segment;
if (min_software_endstops) { clamp_to_software_endstops(arc_target);
if (arc_target[X_AXIS] < X_HOME_POS) arc_target[X_AXIS] = X_HOME_POS;
if (arc_target[Y_AXIS] < Y_HOME_POS) arc_target[Y_AXIS] = Y_HOME_POS;
if (arc_target[Z_AXIS] < Z_HOME_POS) arc_target[Z_AXIS] = Z_HOME_POS;
}
if (max_software_endstops) {
if (arc_target[X_AXIS] > X_MAX_LENGTH) arc_target[X_AXIS] = X_MAX_LENGTH;
if (arc_target[Y_AXIS] > Y_MAX_LENGTH) arc_target[Y_AXIS] = Y_MAX_LENGTH;
if (arc_target[Z_AXIS] > Z_MAX_LENGTH) arc_target[Z_AXIS] = Z_MAX_LENGTH;
}
plan_buffer_line(arc_target[X_AXIS], arc_target[Y_AXIS], arc_target[Z_AXIS], arc_target[E_AXIS], feed_rate, extruder); plan_buffer_line(arc_target[X_AXIS], arc_target[Y_AXIS], arc_target[Z_AXIS], arc_target[E_AXIS], feed_rate, extruder);
} }

Loading…
Cancel
Save