Browse Source

Rename BEEPER to BEEPER_PIN

For consistency with other pins, allowing use of `PIN_EXISTS` macro.
pull/1/head
Scott Lahteine 9 years ago
committed by Richard Wackerbarth
parent
commit
f03e063750
  1. 20
      Marlin/pins_GEN7_CUSTOM.h
  2. 28
      Marlin/pins_OMCA_A.h
  3. 6
      Marlin/pins_RAMPS_13.h
  4. 34
      Marlin/pins_RUMBA.h

20
Marlin/pins_GEN7_CUSTOM.h

@ -13,34 +13,34 @@
#define X_STEP_PIN 21 // different from standard GEN7 #define X_STEP_PIN 21 // different from standard GEN7
#define X_DIR_PIN 20 // different from standard GEN7 #define X_DIR_PIN 20 // different from standard GEN7
#define X_ENABLE_PIN 24 #define X_ENABLE_PIN 24
#define X_STOP_PIN 0 #define X_STOP_PIN 0
//y axis pins //y axis pins
#define Y_STEP_PIN 23 #define Y_STEP_PIN 23
#define Y_DIR_PIN 22 #define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24 #define Y_ENABLE_PIN 24
#define Y_STOP_PIN 1 #define Y_STOP_PIN 1
//z axis pins //z axis pins
#define Z_STEP_PIN 26 #define Z_STEP_PIN 26
#define Z_DIR_PIN 25 #define Z_DIR_PIN 25
#define Z_ENABLE_PIN 24 #define Z_ENABLE_PIN 24
#define Z_STOP_PIN 2 #define Z_STOP_PIN 2
//extruder pins //extruder pins
#define E0_STEP_PIN 28 #define E0_STEP_PIN 28
#define E0_DIR_PIN 27 #define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24 #define E0_ENABLE_PIN 24
#define TEMP_0_PIN 2 #define TEMP_0_PIN 2
#define TEMP_1_PIN -1 #define TEMP_1_PIN -1
#define TEMP_2_PIN -1 #define TEMP_2_PIN -1
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) #define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define HEATER_0_PIN 4 #define HEATER_0_PIN 4
#define HEATER_1_PIN -1 #define HEATER_1_PIN -1
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#define HEATER_BED_PIN 3 // (bed) #define HEATER_BED_PIN 3 // (bed)
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support #define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support
@ -56,9 +56,9 @@
//#define TX_ENABLE_PIN 12 //#define TX_ENABLE_PIN 12
//#define RX_ENABLE_PIN 13 //#define RX_ENABLE_PIN 13
#define BEEPER_PIN -1 #define BEEPER_PIN -1
#define SD_DETECT_PIN -1 #define SD_DETECT_PIN -1
#define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work #define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work
#define KILL_PIN -1 #define KILL_PIN -1
//Pins for 4bit LCD Support //Pins for 4bit LCD Support

28
Marlin/pins_OMCA_A.h

@ -35,39 +35,39 @@
#define X_STEP_PIN 21 #define X_STEP_PIN 21
#define X_DIR_PIN 20 #define X_DIR_PIN 20
#define X_ENABLE_PIN 24 #define X_ENABLE_PIN 24
#define X_STOP_PIN 0 #define X_STOP_PIN 0
#define Y_STEP_PIN 23 #define Y_STEP_PIN 23
#define Y_DIR_PIN 22 #define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24 #define Y_ENABLE_PIN 24
#define Y_STOP_PIN 1 #define Y_STOP_PIN 1
#define Z_STEP_PIN 26 #define Z_STEP_PIN 26
#define Z_DIR_PIN 25 #define Z_DIR_PIN 25
#define Z_ENABLE_PIN 24 #define Z_ENABLE_PIN 24
#define Z_STOP_PIN 2 #define Z_STOP_PIN 2
#define E0_STEP_PIN 28 #define E0_STEP_PIN 28
#define E0_DIR_PIN 27 #define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24 #define E0_ENABLE_PIN 24
#define E1_STEP_PIN -1 // 19 #define E1_STEP_PIN -1 // 19
#define E1_DIR_PIN -1 // 18 #define E1_DIR_PIN -1 // 18
#define E1_ENABLE_PIN 24 #define E1_ENABLE_PIN 24
#define E2_STEP_PIN -1 // 17 #define E2_STEP_PIN -1 // 17
#define E2_DIR_PIN -1 // 16 #define E2_DIR_PIN -1 // 16
#define E2_ENABLE_PIN 24 #define E2_ENABLE_PIN 24
#define SDPOWER -1 #define SDPOWER -1
#define SDSS 11 #define SDSS 11
#define SD_DETECT_PIN -1 // 10 optional also used as mode pin #define SD_DETECT_PIN -1 // 10 optional also used as mode pin
#define LED_PIN -1 #define LED_PIN -1
#define FAN_PIN 3 #define FAN_PIN 3
#define PS_ON_PIN -1 #define PS_ON_PIN -1
#define KILL_PIN -1 #define KILL_PIN -1
#define HEATER_0_PIN 4 #define HEATER_0_PIN 4
#define HEATER_1_PIN -1 // 12 #define HEATER_1_PIN -1 // 12
#define HEATER_2_PIN -1 // 13 #define HEATER_2_PIN -1 // 13
#define TEMP_0_PIN 0 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_0_PIN 0 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!

6
Marlin/pins_RAMPS_13.h

@ -117,10 +117,10 @@
#if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) || MB(RAMPS_13_SF) #if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) || MB(RAMPS_13_SF)
#define HEATER_BED_PIN -1 // NO BED #define HEATER_BED_PIN -1 // NO BED
#else #else
#define HEATER_BED_PIN 8 // BED #define HEATER_BED_PIN 8 // BED
#endif #endif
#define TEMP_BED_PIN 14 // ANALOG NUMBERING #define TEMP_BED_PIN 14 // ANALOG NUMBERING
#if HAS_SERVOS #if HAS_SERVOS
#define SERVO0_PIN 11 #define SERVO0_PIN 11
@ -136,7 +136,7 @@
#endif #endif
#if ENABLED(Z_PROBE_SLED) #if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1 #define SLED_PIN -1
#endif #endif
#if ENABLED(ULTRA_LCD) #if ENABLED(ULTRA_LCD)

34
Marlin/pins_RUMBA.h

@ -42,41 +42,41 @@
#define LED_PIN 13 #define LED_PIN 13
#define FAN_PIN 7 #define FAN_PIN 7
#define FAN1_PIN 8 #define FAN1_PIN 8
#define PS_ON_PIN 45 #define PS_ON_PIN 45
#define KILL_PIN 46 #define KILL_PIN 46
#if (TEMP_SENSOR_0==0) #if (TEMP_SENSOR_0==0)
#define TEMP_0_PIN -1 #define TEMP_0_PIN -1
#define HEATER_0_PIN -1 #define HEATER_0_PIN -1
#else #else
#define HEATER_0_PIN 2 // EXTRUDER 1 #define HEATER_0_PIN 2 // EXTRUDER 1
#if (TEMP_SENSOR_0==-1) #if (TEMP_SENSOR_0==-1)
#define TEMP_0_PIN 6 // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used #define TEMP_0_PIN 6 // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
#else #else
#define TEMP_0_PIN 15 // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used #define TEMP_0_PIN 15 // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used
#endif #endif
#endif #endif
#if (TEMP_SENSOR_1==0) #if (TEMP_SENSOR_1==0)
#define TEMP_1_PIN -1 #define TEMP_1_PIN -1
#define HEATER_1_PIN -1 #define HEATER_1_PIN -1
#else #else
#define HEATER_1_PIN 3 // EXTRUDER 2 #define HEATER_1_PIN 3 // EXTRUDER 2
#if (TEMP_SENSOR_1==-1) #if (TEMP_SENSOR_1==-1)
#define TEMP_1_PIN 5 // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used #define TEMP_1_PIN 5 // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
#else #else
#define TEMP_1_PIN 14 // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used #define TEMP_1_PIN 14 // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used
#endif #endif
#endif #endif
#if (TEMP_SENSOR_2==0) #if (TEMP_SENSOR_2==0)
#define TEMP_2_PIN -1 #define TEMP_2_PIN -1
#define HEATER_2_PIN -1 #define HEATER_2_PIN -1
#else #else
#define HEATER_2_PIN 6 // EXTRUDER 3 #define HEATER_2_PIN 6 // EXTRUDER 3
#if (TEMP_SENSOR_2==-1) #if (TEMP_SENSOR_2==-1)
#define TEMP_2_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple #define TEMP_2_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple
#else #else
@ -88,14 +88,14 @@
//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4 //optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4
#if (TEMP_SENSOR_BED==0) #if (TEMP_SENSOR_BED==0)
#define TEMP_BED_PIN -1 #define TEMP_BED_PIN -1
#define HEATER_BED_PIN -1 #define HEATER_BED_PIN -1
#else #else
#define HEATER_BED_PIN 9 // BED #define HEATER_BED_PIN 9 // BED
#if (TEMP_SENSOR_BED==-1) #if (TEMP_SENSOR_BED==-1)
#define TEMP_BED_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple #define TEMP_BED_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple
#else #else
#define TEMP_BED_PIN 11 // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used #define TEMP_BED_PIN 11 // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
#endif #endif
#endif #endif

Loading…
Cancel
Save