diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 56f512f13f..403e281b42 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -416,7 +416,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 13
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -559,7 +559,7 @@
   //#define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
   //#define PID_OPENLOOP          // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
-  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+  #define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
                                   // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 #endif
 
@@ -749,7 +749,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {  161.0, 161.0, 800, 830 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {  161.0, 161.0, 800, 820 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -1166,7 +1166,7 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE + X_MIN_POS
 #define Y_MAX_POS Y_BED_SIZE + Y_MIN_POS
-#define Z_MAX_POS 210
+#define Z_MAX_POS 200
 
 /**
  * Software Endstops
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index cf173755b5..c68605cd27 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -507,11 +507,11 @@
 #if ENABLED(CASE_LIGHT_ENABLE)
   #define CASE_LIGHT_PIN LED_CASE_PIN         // Override the default pin if needed
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
-  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_ON false         // Set default power-up state on
   #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255   // Set default power-up brightness (0-255, requires PWM pin)
   #define CASE_LIGHT_MAX_PWM 255              // Limit pwm
   #define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
-  #define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
+  //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
   //#define CASE_LIGHT_USE_NEOPIXEL           // Use NeoPixel LED as case light, requires NEOPIXEL_LED.
   #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
     #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
@@ -3158,7 +3158,7 @@
  *  - M206 and M428 are disabled.
  *  - G92 will revert to its behavior from Marlin 1.0.
  */
-//#define NO_WORKSPACE_OFFSETS
+#define NO_WORKSPACE_OFFSETS
 
 // Extra options for the M114 "Current Position" report
 //#define M114_DETAIL         // Use 'M114` for details to check planner calculations
@@ -3236,17 +3236,23 @@
   #define USER_DESC_1 "Home & UBL Info"
   #define USER_GCODE_1 "G28\nG29 W"
 
-  #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
-  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+  #define USER_DESC_2 "Light ON"
+  #define USER_GCODE_2 "M355 S1"
 
-  #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
-  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+  #define USER_DESC_3 "Light OFF"
+  #define USER_GCODE_3 "M355 S0"
 
-  #define USER_DESC_4 "Heat Bed/Home/Level"
-  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+//  #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
+//  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
 
-  #define USER_DESC_5 "Power off"
-  #define USER_GCODE_5 "M81"
+//  #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
+//  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+
+//  #define USER_DESC_4 "Heat Bed/Home/Level"
+//  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+
+  #define USER_DESC_4 "Power off"
+  #define USER_GCODE_4 "M81"
 
 #endif