Drop DISABLE_M(IN|AX)_ENDSTOPS, replace with individual endstop flags

Marlin/Conditionals.h

@@ -275,17 +275,25 @@
   #include "Arduino.h"
 
   /**
-   * ENDSTOPPULLUPS
+   * Set ENDSTOPPULLUPS for unused endstop switches
    */
   #if ENABLED(ENDSTOPPULLUPS)
-    #if DISABLED(DISABLE_MAX_ENDSTOPS)
+    #if DISABLED(USE_XMAX_PLUG)
       #define ENDSTOPPULLUP_XMAX
+    #endif
+    #if DISABLED(USE_YMAX_PLUG)
       #define ENDSTOPPULLUP_YMAX
+    #endif
+    #if DISABLED(USE_ZMAX_PLUG)
       #define ENDSTOPPULLUP_ZMAX
     #endif
-    #if DISABLED(DISABLE_MIN_ENDSTOPS)
+    #if DISABLED(USE_XMIN_PLUG)
       #define ENDSTOPPULLUP_XMIN
+    #endif
+    #if DISABLED(USE_YMIN_PLUG)
       #define ENDSTOPPULLUP_YMIN
+    #endif
+    #if DISABLED(USE_ZMIN_PLUG)
       #define ENDSTOPPULLUP_ZMIN
     #endif
     #if DISABLED(DISABLE_Z_MIN_PROBE_ENDSTOP)

Marlin/Configuration.h

@@ -346,8 +346,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -370,8 +384,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/SanityCheck.h

@@ -419,6 +419,17 @@
   #error TEMP_SENSOR_0 is required.
 #endif
 
+/**
+ * Endstops
+ */
+#if DISABLED(HAS_ENDSTOP_X_MIN) && DISABLED(HAS_ENDSTOP_X_MAX)
+ #error You must enable HAS_ENDSTOP_X_MIN or HAS_ENDSTOP_X_MAX
+#elif DISABLED(HAS_ENDSTOP_Y_MIN) && DISABLED(HAS_ENDSTOP_Y_MAX)
+ #error You must enable HAS_ENDSTOP_Y_MIN or HAS_ENDSTOP_Y_MAX
+#elif DISABLED(HAS_ENDSTOP_Z_MIN) && DISABLED(HAS_ENDSTOP_Z_MAX)
+ #error You must enable HAS_ENDSTOP_Z_MIN or HAS_ENDSTOP_Z_MAX
+#endif
+
 /**
  * Warnings for old configurations
  */
@@ -456,6 +467,8 @@
   #error Z_RAISE_BEFORE_HOMING is deprecated. Use MIN_Z_HEIGHT_FOR_HOMING instead.
 #elif defined(FILAMENT_SENSOR)
   #error FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead.
+#elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
+  #error DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated - set USE_*_ENDSTOP flags instead
 #endif
 
 #endif //SANITYCHECK_H

Marlin/example_configurations/Felix/Configuration.h

@@ -328,8 +328,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -352,8 +366,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -325,8 +325,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -349,8 +363,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Hephestos/Configuration.h

@@ -338,8 +338,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -362,8 +376,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/K8200/Configuration.h

@@ -363,8 +363,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -387,8 +401,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -346,8 +346,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -370,8 +384,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/RigidBot/Configuration.h

@@ -340,8 +340,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -364,8 +378,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/SCARA/Configuration.h

@@ -354,8 +354,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 //#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -378,8 +392,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/TAZ4/Configuration.h

@@ -367,8 +367,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -391,8 +405,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/WITBOX/Configuration.h

@@ -338,8 +338,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -362,8 +376,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -346,8 +346,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -370,8 +384,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/generic/Configuration.h

@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG // a Z probe
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -370,8 +370,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG // a Z probe
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -394,8 +408,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/makibox/Configuration.h

@@ -349,8 +349,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -373,8 +387,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -336,8 +336,22 @@
 // Enable this option for Toshiba steppers
 #define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -360,8 +374,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/pins.h

@@ -209,55 +209,37 @@
   #endif
 #endif
 
-#if ENABLED(DISABLE_MAX_ENDSTOPS)
-  #undef X_MAX_PIN
-  #undef Y_MAX_PIN
-  #undef Z_MAX_PIN
-  #define X_MAX_PIN          -1
-  #define Y_MAX_PIN          -1
-  #define Z_MAX_PIN          -1
-#endif
-
-#if ENABLED(DISABLE_MIN_ENDSTOPS)
-  #undef X_MIN_PIN
-  #undef Y_MIN_PIN
-  #undef Z_MIN_PIN
-  #define X_MIN_PIN          -1
-  #define Y_MIN_PIN          -1
-  #define Z_MIN_PIN          -1
-#endif
-
 #if ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP) || DISABLED(Z_MIN_PROBE_ENDSTOP) // Allow code to compile regardless of Z_MIN_PROBE_ENDSTOP setting.
   #undef Z_MIN_PROBE_PIN
   #define Z_MIN_PROBE_PIN    -1
 #endif
 
-#if ENABLED(DISABLE_XMAX_ENDSTOP)
+#if DISABLED(USE_XMAX_PLUG)
   #undef X_MAX_PIN
   #define X_MAX_PIN          -1
 #endif
 
-#if ENABLED(DISABLE_XMIN_ENDSTOP)
-  #undef X_MIN_PIN
-  #define X_MIN_PIN          -1
-#endif
-
-#if ENABLED(DISABLE_YMAX_ENDSTOP)
+#if DISABLED(USE_YMAX_PLUG)
   #undef Y_MAX_PIN
   #define Y_MAX_PIN          -1
 #endif
 
-#if ENABLED(DISABLE_YMIN_ENDSTOP)
-  #undef Y_MIN_PIN
-  #define Y_MIN_PIN          -1
-#endif
-
-#if ENABLED(DISABLE_ZMAX_ENDSTOP)
+#if DISABLED(USE_ZMAX_PLUG)
   #undef Z_MAX_PIN
   #define Z_MAX_PIN          -1
 #endif
 
-#if ENABLED(DISABLE_ZMIN_ENDSTOP)
+#if DISABLED(USE_XMIN_PLUG)
+  #undef X_MIN_PIN
+  #define X_MIN_PIN          -1
+#endif
+
+#if DISABLED(USE_YMIN_PLUG)
+  #undef Y_MIN_PIN
+  #define Y_MIN_PIN          -1
+#endif
+
+#if DISABLED(USE_ZMIN_PLUG)
   #undef Z_MIN_PIN
   #define Z_MIN_PIN          -1
 #endif

Marlin/pins_FELIX2.h

@@ -29,8 +29,6 @@
 #undef HEATER_1_PIN
 #define HEATER_1_PIN        7 // EXTRUDER 2
 
-#define DISABLE_MAX_ENDSTOPS
-
 #undef SDPOWER
 #define SDPOWER             1