Fix comments in Configuration_adv.h

8 years ago · e08915a723
16 changed files with 272 additions and 320 deletions
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/K8200/Configuration_adv.h
@ -53,22 +53,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 60        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 8     // Degrees Celsius
@ -86,11 +83,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/RigidBot/Configuration_adv.h
+++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 3000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/TAZ4/Configuration_adv.h
+++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 120   // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@ -52,22 +52,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -85,11 +82,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@ -47,22 +47,19 @@
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control

 /**
- * Thermal Protection parameters
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
 */
-  /**
-   * Thermal Protection protects your printer from damage and fire if a
-   * thermistor falls out or temperature sensors fail in any way.
-   *
-   * The issue: If a thermistor falls out or a temperature sensor fails,
-   * Marlin can no longer sense the actual temperature. Since a disconnected
-   * thermistor reads as a low temperature, the firmware will keep the heater on.
-   *
-   * The solution: Once the temperature reaches the target, start observing.
-   * If the temperature stays too far below the target (hysteresis) for too long (period),
-   * the firmware will halt the machine as a safety precaution.
-   *
-   * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
-   */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
@ -80,11 +77,11 @@
  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif

-  /**
-   * Thermal Protection parameters for the bed
-   * are like the above for the hotends.
-   * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
-   */
+/**
+ * Thermal Protection parameters for the bed
+ * are like the above for the hotends.
+ * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now.
+ */
 #if ENABLED(THERMAL_PROTECTION_BED)
  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius