Rename QUIET_PROBING

Marlin/src/inc/Conditionals_post.h

@@ -2373,7 +2373,7 @@
 #endif
 
 #if HAS_BED_PROBE && (EITHER(PROBING_HEATERS_OFF, PROBING_FANS_OFF) || DELAY_BEFORE_PROBING > 0)
-  #define QUIET_PROBING 1
+  #define HAS_QUIET_PROBING 1
 #endif
 #if EITHER(ADVANCED_PAUSE_FEATURE, PROBING_HEATERS_OFF)
   #define HEATER_IDLE_HANDLER 1

Marlin/src/lcd/menu/menu_bed_corners.cpp

@@ -104,7 +104,7 @@ static int8_t bed_corner;
     #if ENABLED(BLTOUCH) && DISABLED(BLTOUCH_HS_MODE)
       bltouch.deploy(); // DEPLOY in LOW SPEED MODE on every probe action
     #endif
-    TERN_(QUIET_PROBING, probe.set_probing_paused(true));
+    TERN_(HAS_QUIET_PROBING, probe.set_probing_paused(true));
 
     // Move down until the probe is triggered
     do_blocking_move_to_z(last_z - (LEVEL_CORNERS_PROBE_TOLERANCE), manual_feedrate_mm_s.z);
@@ -141,7 +141,7 @@ static int8_t bed_corner;
       TERN_(LEVEL_CORNERS_VERIFY_RAISED, verify_corner = true);
     }
 
-    TERN_(QUIET_PROBING, probe.set_probing_paused(false));
+    TERN_(HAS_QUIET_PROBING, probe.set_probing_paused(false));
 
     #if ENABLED(BLTOUCH) && DISABLED(BLTOUCH_HS_MODE)
       bltouch.stow();

Marlin/src/module/motion.cpp

@@ -1321,7 +1321,7 @@ void do_homing_move(const AxisEnum axis, const float distance, const feedRate_t
 
   if (is_home_dir) {
 
-    #if HOMING_Z_WITH_PROBE && QUIET_PROBING
+    #if HOMING_Z_WITH_PROBE && HAS_QUIET_PROBING
       if (axis == Z_AXIS) probe.set_probing_paused(true);
     #endif
 
@@ -1360,7 +1360,7 @@ void do_homing_move(const AxisEnum axis, const float distance, const feedRate_t
 
   if (is_home_dir) {
 
-    #if HOMING_Z_WITH_PROBE && QUIET_PROBING
+    #if HOMING_Z_WITH_PROBE && HAS_QUIET_PROBING
       if (axis == Z_AXIS) probe.set_probing_paused(false);
     #endif
 

Marlin/src/module/probe.cpp

@@ -73,7 +73,7 @@
   #include "../feature/tmc_util.h"
 #endif
 
-#if QUIET_PROBING
+#if HAS_QUIET_PROBING
   #include "stepper/indirection.h"
 #endif
 
@@ -236,7 +236,7 @@ xyz_pos_t Probe::offset; // Initialized by settings.load()
 
 #endif // Z_PROBE_ALLEN_KEY
 
-#if QUIET_PROBING
+#if HAS_QUIET_PROBING
 
   void Probe::set_probing_paused(const bool p) {
     TERN_(PROBING_HEATERS_OFF, thermalManager.pause(p));
@@ -254,7 +254,7 @@ xyz_pos_t Probe::offset; // Initialized by settings.load()
     );
   }
 
-#endif // QUIET_PROBING
+#endif // HAS_QUIET_PROBING
 
 /**
  * Raise Z to a minimum height to make room for a probe to move
@@ -437,7 +437,7 @@ bool Probe::probe_down_to_z(const float z, const feedRate_t fr_mm_s) {
     endstops.enable(true);
   #endif
 
-  TERN_(QUIET_PROBING, set_probing_paused(true));
+  TERN_(HAS_QUIET_PROBING, set_probing_paused(true));
 
   // Move down until the probe is triggered
   do_blocking_move_to_z(z, fr_mm_s);
@@ -451,7 +451,7 @@ bool Probe::probe_down_to_z(const float z, const feedRate_t fr_mm_s) {
     #endif
   ;
 
-  TERN_(QUIET_PROBING, set_probing_paused(false));
+  TERN_(HAS_QUIET_PROBING, set_probing_paused(false));
 
   // Re-enable stealthChop if used. Disable diag1 pin on driver.
   #if ENABLED(SENSORLESS_PROBING)

Marlin/src/module/probe.h

@@ -202,7 +202,7 @@ public:
     static void servo_probe_init();
   #endif
 
-  #if QUIET_PROBING
+  #if HAS_QUIET_PROBING
     static void set_probing_paused(const bool p);
   #endif