Scott Lahteine
9 years ago
155 changed files with 10242 additions and 8335 deletions
@ -0,0 +1,4 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
rm -rf .build/ |
||||
|
DISPLAY=:1.0 ~/bin/arduino --verify --board marlin:avr:mega Marlin/Marlin.ino |
||||
@ -0,0 +1,5 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
for opt in "$@" ; do |
||||
|
eval "sed -i 's/\(\/\/ *\)*\(\#define *$opt\)/\/\/\2/g' Marlin/Configuration.h" |
||||
|
done |
||||
@ -0,0 +1,5 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
for opt in "$@" ; do |
||||
|
eval "sed -i 's/\/\/ *\(#define *$opt\)/\1/g' Marlin/Configuration.h" |
||||
|
done |
||||
@ -0,0 +1,5 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
for opt in "$@" ; do |
||||
|
eval "sed -i 's/\/\/ *\(#define *$opt\)/\1/g' Marlin/Configuration_adv.h" |
||||
|
done |
||||
@ -0,0 +1,3 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
eval "sed -i 's/\(#define *$1\) *.*$/\1 $2/g' Marlin/Configuration.h" |
||||
@ -0,0 +1,3 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
eval "sed -i 's/\(#define *$1\) *.*$/\1 $2/g' Marlin/Configuration_adv.h" |
||||
@ -0,0 +1,3 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
eval "sed -i 's/\(#define *$2\) *.*$/\1 $3/g' Marlin/pins_$1.h" |
||||
@ -0,0 +1,5 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
cp Marlin/Configuration.h.backup Marlin/Configuration.h |
||||
|
cp Marlin/Configuration_adv.h.backup Marlin/Configuration_adv.h |
||||
|
cp Marlin/pins_RAMPS_14.h.backup Marlin/pins_RAMPS_14.h |
||||
@ -0,0 +1,3 @@ |
|||||
|
#!/usr/bin/env bash |
||||
|
|
||||
|
eval "cp Marlin/example_configurations/$1/Configuration* Marlin/" |
||||
File diff suppressed because it is too large
@ -1 +0,0 @@ |
|||||
Header set Access-Control-Allow-Origin "*" |
|
||||
@ -1,64 +0,0 @@ |
|||||
#ifndef BOARDS_H |
|
||||
#define BOARDS_H |
|
||||
|
|
||||
#define BOARD_UNKNOWN -1 |
|
||||
|
|
||||
#define BOARD_GEN7_CUSTOM 10 // Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
|
||||
#define BOARD_GEN7_12 11 // Gen7 v1.1, v1.2
|
|
||||
#define BOARD_GEN7_13 12 // Gen7 v1.3
|
|
||||
#define BOARD_GEN7_14 13 // Gen7 v1.4
|
|
||||
#define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0
|
|
||||
#define BOARD_SETHI 20 // Sethi 3D_1
|
|
||||
#define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2
|
|
||||
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
|
||||
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
|
||||
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
|
||||
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
|
||||
#define BOARD_RAMPS_13_SF 38 // RAMPS 1.3 / 1.4 (Power outputs: Spindle, Controller Fan)
|
|
||||
#define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like)
|
|
||||
#define BOARD_RIGIDBOARD 42 // Invent-A-Part RigidBoard
|
|
||||
#define BOARD_GEN6 5 // Gen6
|
|
||||
#define BOARD_GEN6_DELUXE 51 // Gen6 deluxe
|
|
||||
#define BOARD_SANGUINOLOLU_11 6 // Sanguinololu < 1.2
|
|
||||
#define BOARD_SANGUINOLOLU_12 62 // Sanguinololu 1.2 and above
|
|
||||
#define BOARD_MELZI 63 // Melzi
|
|
||||
#define BOARD_STB_11 64 // STB V1.1
|
|
||||
#define BOARD_AZTEEG_X1 65 // Azteeg X1
|
|
||||
#define BOARD_MELZI_MAKR3D 66 // Melzi with ATmega1284 (MaKr3d version)
|
|
||||
#define BOARD_AZTEEG_X3 67 // Azteeg X3
|
|
||||
#define BOARD_AZTEEG_X3_PRO 68 // Azteeg X3 Pro
|
|
||||
#define BOARD_ULTIMAKER 7 // Ultimaker
|
|
||||
#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
|
||||
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
|
||||
#define BOARD_3DRAG 77 // 3Drag Controller
|
|
||||
#define BOARD_K8200 78 // Vellemann K8200 Controller (derived from 3Drag Controller)
|
|
||||
#define BOARD_TEENSYLU 8 // Teensylu
|
|
||||
#define BOARD_RUMBA 80 // Rumba
|
|
||||
#define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286)
|
|
||||
#define BOARD_BRAINWAVE 82 // Brainwave (AT90USB646)
|
|
||||
#define BOARD_SAV_MKI 83 // SAV Mk-I (AT90USB1286)
|
|
||||
#define BOARD_TEENSY2 84 // Teensy++2.0 (AT90USB1286) - CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
|
||||
#define BOARD_BRAINWAVE_PRO 85 // Brainwave Pro (AT90USB1286)
|
|
||||
#define BOARD_GEN3_PLUS 9 // Gen3+
|
|
||||
#define BOARD_GEN3_MONOLITHIC 22 // Gen3 Monolithic Electronics
|
|
||||
#define BOARD_MEGATRONICS 70 // Megatronics
|
|
||||
#define BOARD_MEGATRONICS_2 701 // Megatronics v2.0
|
|
||||
#define BOARD_MINITRONICS 702 // Minitronics v1.0/1.1
|
|
||||
#define BOARD_MEGATRONICS_3 703 // Megatronics v3.0
|
|
||||
#define BOARD_OMCA_A 90 // Alpha OMCA board
|
|
||||
#define BOARD_OMCA 91 // Final OMCA board
|
|
||||
#define BOARD_RAMBO 301 // Rambo
|
|
||||
#define BOARD_MINIRAMBO 302 // Mini-Rambo
|
|
||||
#define BOARD_MEGACONTROLLER 310 // Mega controller
|
|
||||
#define BOARD_ELEFU_3 21 // Elefu Ra Board (v3)
|
|
||||
#define BOARD_5DPRINT 88 // 5DPrint D8 Driver Board
|
|
||||
#define BOARD_LEAPFROG 999 // Leapfrog
|
|
||||
#define BOARD_MKS_BASE 40 // MKS BASE 1.0
|
|
||||
#define BOARD_BAM_DICE 401 // 2PrintBeta BAM&DICE with STK drivers
|
|
||||
#define BOARD_BAM_DICE_DUE 402 // 2PrintBeta BAM&DICE Due with STK drivers
|
|
||||
|
|
||||
#define BOARD_99 99 // This is in pins.h but...?
|
|
||||
|
|
||||
#define MB(board) (MOTHERBOARD==BOARD_##board) |
|
||||
|
|
||||
#endif //__BOARDS_H
|
|
||||
@ -1,228 +0,0 @@ |
|||||
#ifndef LANGUAGE_H |
|
||||
#define LANGUAGE_H |
|
||||
|
|
||||
#include "Configuration.h" |
|
||||
|
|
||||
#define LANGUAGE_CONCAT(M) #M |
|
||||
#define GENERATE_LANGUAGE_INCLUDE(M) LANGUAGE_CONCAT(language_##M.h) |
|
||||
|
|
||||
|
|
||||
// NOTE: IF YOU CHANGE LANGUAGE FILES OR MERGE A FILE WITH CHANGES
|
|
||||
//
|
|
||||
// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h"
|
|
||||
// ==> ALSO TRY ALL AVAILABLE LANGUAGE OPTIONS
|
|
||||
// See also documentation/LCDLanguageFont.md
|
|
||||
|
|
||||
// Languages
|
|
||||
// en English
|
|
||||
// pl Polish
|
|
||||
// fr French
|
|
||||
// de German
|
|
||||
// es Spanish
|
|
||||
// ru Russian
|
|
||||
// bg Bulgarian
|
|
||||
// it Italian
|
|
||||
// pt Portuguese
|
|
||||
// pt-br Portuguese (Brazil)
|
|
||||
// fi Finnish
|
|
||||
// an Aragonese
|
|
||||
// nl Dutch
|
|
||||
// ca Catalan
|
|
||||
// eu Basque-Euskera
|
|
||||
// kana Japanese
|
|
||||
// kana_utf Japanese
|
|
||||
// cn Chinese
|
|
||||
|
|
||||
// fallback if no language is set, don't change
|
|
||||
#ifndef LANGUAGE_INCLUDE |
|
||||
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) |
|
||||
#endif |
|
||||
|
|
||||
#if ENABLED(USE_AUTOMATIC_VERSIONING) |
|
||||
#include "_Version.h" |
|
||||
#else |
|
||||
#include "Default_Version.h" |
|
||||
#endif |
|
||||
|
|
||||
#define PROTOCOL_VERSION "1.0" |
|
||||
|
|
||||
#if MB(ULTIMAKER)|| MB(ULTIMAKER_OLD)|| MB(ULTIMAIN_2) |
|
||||
#define MACHINE_NAME "Ultimaker" |
|
||||
#define SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin"
|
|
||||
#elif MB(RUMBA) |
|
||||
#define MACHINE_NAME "Rumba" |
|
||||
#elif MB(3DRAG) |
|
||||
#define MACHINE_NAME "3Drag" |
|
||||
#define SOURCE_CODE_URL "http://3dprint.elettronicain.it/"
|
|
||||
#elif MB(K8200) |
|
||||
#define MACHINE_NAME "K8200" |
|
||||
#define SOURCE_CODE_URL "https://github.com/CONSULitAS/Marlin-K8200"
|
|
||||
#elif MB(5DPRINT) |
|
||||
#define MACHINE_NAME "Makibox" |
|
||||
#elif MB(SAV_MKI) |
|
||||
#define MACHINE_NAME "SAV MkI" |
|
||||
#define SOURCE_CODE_URL "https://github.com/fmalpartida/Marlin/tree/SAV-MkI-config"
|
|
||||
#elif !defined(MACHINE_NAME) |
|
||||
#define MACHINE_NAME "3D Printer" |
|
||||
#endif |
|
||||
|
|
||||
#ifdef CUSTOM_MACHINE_NAME |
|
||||
#undef MACHINE_NAME |
|
||||
#define MACHINE_NAME CUSTOM_MACHINE_NAME |
|
||||
#endif |
|
||||
|
|
||||
#ifndef SOURCE_CODE_URL |
|
||||
#define SOURCE_CODE_URL "https://github.com/MarlinFirmware/Marlin"
|
|
||||
#endif |
|
||||
|
|
||||
#ifndef DETAILED_BUILD_VERSION |
|
||||
#error BUILD_VERSION Information must be specified |
|
||||
#endif |
|
||||
|
|
||||
#ifndef MACHINE_UUID |
|
||||
#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" |
|
||||
#endif |
|
||||
|
|
||||
|
|
||||
#define STRINGIFY_(n) #n |
|
||||
#define STRINGIFY(n) STRINGIFY_(n) |
|
||||
|
|
||||
|
|
||||
// Common LCD messages
|
|
||||
|
|
||||
/* nothing here yet */ |
|
||||
|
|
||||
// Common serial messages
|
|
||||
#define MSG_MARLIN "Marlin" |
|
||||
|
|
||||
// Serial Console Messages (do not translate those!)
|
|
||||
|
|
||||
#define MSG_Enqueueing "enqueueing \"" |
|
||||
#define MSG_POWERUP "PowerUp" |
|
||||
#define MSG_EXTERNAL_RESET " External Reset" |
|
||||
#define MSG_BROWNOUT_RESET " Brown out Reset" |
|
||||
#define MSG_WATCHDOG_RESET " Watchdog Reset" |
|
||||
#define MSG_SOFTWARE_RESET " Software Reset" |
|
||||
#define MSG_AUTHOR " | Author: " |
|
||||
#define MSG_CONFIGURATION_VER " Last Updated: " |
|
||||
#define MSG_FREE_MEMORY " Free Memory: " |
|
||||
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: " |
|
||||
#define MSG_OK "ok" |
|
||||
#define MSG_WAIT "wait" |
|
||||
#define MSG_FILE_SAVED "Done saving file." |
|
||||
#define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line: " |
|
||||
#define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line: " |
|
||||
#define MSG_ERR_NO_CHECKSUM "No Checksum with line number, Last Line: " |
|
||||
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No Line Number with checksum, Last Line: " |
|
||||
#define MSG_FILE_PRINTED "Done printing file" |
|
||||
#define MSG_BEGIN_FILE_LIST "Begin file list" |
|
||||
#define MSG_END_FILE_LIST "End file list" |
|
||||
#define MSG_INVALID_EXTRUDER "Invalid extruder" |
|
||||
#define MSG_INVALID_SOLENOID "Invalid solenoid" |
|
||||
#define MSG_ERR_NO_THERMISTORS "No thermistors - no temperature" |
|
||||
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin " DETAILED_BUILD_VERSION " SOURCE_CODE_URL:" SOURCE_CODE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n" |
|
||||
#define MSG_COUNT_X " Count X: " |
|
||||
#define MSG_ERR_KILLED "Printer halted. kill() called!" |
|
||||
#define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)" |
|
||||
#define MSG_RESEND "Resend: " |
|
||||
#define MSG_UNKNOWN_COMMAND "Unknown command: \"" |
|
||||
#define MSG_ACTIVE_EXTRUDER "Active Extruder: " |
|
||||
#define MSG_X_MIN "x_min: " |
|
||||
#define MSG_X_MAX "x_max: " |
|
||||
#define MSG_Y_MIN "y_min: " |
|
||||
#define MSG_Y_MAX "y_max: " |
|
||||
#define MSG_Z_MIN "z_min: " |
|
||||
#define MSG_Z_MAX "z_max: " |
|
||||
#define MSG_Z2_MAX "z2_max: " |
|
||||
#define MSG_Z_PROBE "z_probe: " |
|
||||
#define MSG_ERR_MATERIAL_INDEX "M145 S<index> out of range (0-1)" |
|
||||
#define MSG_ERR_M421_REQUIRES_XYZ "M421 requires XYZ parameters" |
|
||||
#define MSG_ERR_MESH_INDEX_OOB "Mesh XY index is out of bounds" |
|
||||
#define MSG_ERR_M428_TOO_FAR "Too far from reference point" |
|
||||
#define MSG_M119_REPORT "Reporting endstop status" |
|
||||
#define MSG_ENDSTOP_HIT "TRIGGERED" |
|
||||
#define MSG_ENDSTOP_OPEN "open" |
|
||||
#define MSG_HOTEND_OFFSET "Hotend offsets:" |
|
||||
|
|
||||
#define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir" |
|
||||
#define MSG_SD_INIT_FAIL "SD init fail" |
|
||||
#define MSG_SD_VOL_INIT_FAIL "volume.init failed" |
|
||||
#define MSG_SD_OPENROOT_FAIL "openRoot failed" |
|
||||
#define MSG_SD_CARD_OK "SD card ok" |
|
||||
#define MSG_SD_WORKDIR_FAIL "workDir open failed" |
|
||||
#define MSG_SD_OPEN_FILE_FAIL "open failed, File: " |
|
||||
#define MSG_SD_FILE_OPENED "File opened: " |
|
||||
#define MSG_SD_SIZE " Size: " |
|
||||
#define MSG_SD_FILE_SELECTED "File selected" |
|
||||
#define MSG_SD_WRITE_TO_FILE "Writing to file: " |
|
||||
#define MSG_SD_PRINTING_BYTE "SD printing byte " |
|
||||
#define MSG_SD_NOT_PRINTING "Not SD printing" |
|
||||
#define MSG_SD_ERR_WRITE_TO_FILE "error writing to file" |
|
||||
#define MSG_SD_CANT_ENTER_SUBDIR "Cannot enter subdir: " |
|
||||
|
|
||||
#define MSG_STEPPER_TOO_HIGH "Steprate too high: " |
|
||||
#define MSG_ENDSTOPS_HIT "endstops hit: " |
|
||||
#define MSG_ERR_COLD_EXTRUDE_STOP " cold extrusion prevented" |
|
||||
#define MSG_ERR_LONG_EXTRUDE_STOP " too long extrusion prevented" |
|
||||
#define MSG_TOO_COLD_FOR_M600 "M600 Hotend too cold to change filament" |
|
||||
#define MSG_BABYSTEPPING_X "Babystepping X" |
|
||||
#define MSG_BABYSTEPPING_Y "Babystepping Y" |
|
||||
#define MSG_BABYSTEPPING_Z "Babystepping Z" |
|
||||
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Error in menu structure" |
|
||||
|
|
||||
#define MSG_ERR_EEPROM_WRITE "Error writing to EEPROM!" |
|
||||
|
|
||||
// temperature.cpp strings
|
|
||||
#define MSG_PID_AUTOTUNE "PID Autotune" |
|
||||
#define MSG_PID_AUTOTUNE_START MSG_PID_AUTOTUNE " start" |
|
||||
#define MSG_PID_AUTOTUNE_FAILED MSG_PID_AUTOTUNE " failed!" |
|
||||
#define MSG_PID_BAD_EXTRUDER_NUM MSG_PID_AUTOTUNE_FAILED " Bad extruder number" |
|
||||
#define MSG_PID_TEMP_TOO_HIGH MSG_PID_AUTOTUNE_FAILED " Temperature too high" |
|
||||
#define MSG_PID_TIMEOUT MSG_PID_AUTOTUNE_FAILED " timeout" |
|
||||
#define MSG_BIAS " bias: " |
|
||||
#define MSG_D " d: " |
|
||||
#define MSG_T_MIN " min: " |
|
||||
#define MSG_T_MAX " max: " |
|
||||
#define MSG_KU " Ku: " |
|
||||
#define MSG_TU " Tu: " |
|
||||
#define MSG_CLASSIC_PID " Classic PID " |
|
||||
#define MSG_KP " Kp: " |
|
||||
#define MSG_KI " Ki: " |
|
||||
#define MSG_KD " Kd: " |
|
||||
#define MSG_B "B:" |
|
||||
#define MSG_T "T:" |
|
||||
#define MSG_AT " @:" |
|
||||
#define MSG_PID_AUTOTUNE_FINISHED MSG_PID_AUTOTUNE " finished! Put the last Kp, Ki and Kd constants from below into Configuration.h" |
|
||||
#define MSG_PID_DEBUG " PID_DEBUG " |
|
||||
#define MSG_PID_DEBUG_INPUT ": Input " |
|
||||
#define MSG_PID_DEBUG_OUTPUT " Output " |
|
||||
#define MSG_PID_DEBUG_PTERM " pTerm " |
|
||||
#define MSG_PID_DEBUG_ITERM " iTerm " |
|
||||
#define MSG_PID_DEBUG_DTERM " dTerm " |
|
||||
#define MSG_PID_DEBUG_CTERM " cTerm " |
|
||||
#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !" |
|
||||
|
|
||||
#define MSG_HEATER_BED "bed" |
|
||||
#define MSG_STOPPED_HEATER ", system stopped! Heater_ID: " |
|
||||
#define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !" |
|
||||
#define MSG_T_HEATING_FAILED "Heating failed" |
|
||||
#define MSG_T_THERMAL_RUNAWAY "Thermal Runaway" |
|
||||
#define MSG_T_MAXTEMP "MAXTEMP triggered" |
|
||||
#define MSG_T_MINTEMP "MINTEMP triggered" |
|
||||
|
|
||||
// Debug
|
|
||||
#define MSG_DEBUG_ECHO "DEBUG ECHO ENABLED" |
|
||||
#define MSG_DEBUG_INFO "DEBUG INFO ENABLED" |
|
||||
#define MSG_DEBUG_ERRORS "DEBUG ERRORS ENABLED" |
|
||||
#define MSG_DEBUG_DRYRUN "DEBUG DRYRUN ENABLED" |
|
||||
|
|
||||
// LCD Menu Messages
|
|
||||
|
|
||||
#if DISABLED(DISPLAY_CHARSET_HD44780_JAPAN) && DISABLED(DISPLAY_CHARSET_HD44780_WESTERN) && DISABLED(DISPLAY_CHARSET_HD44780_CYRILLIC) |
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN |
|
||||
#endif |
|
||||
|
|
||||
#include LANGUAGE_INCLUDE |
|
||||
#include "language_en.h" |
|
||||
|
|
||||
#endif //__LANGUAGE_H
|
|
||||
@ -1,344 +0,0 @@ |
|||||
/* configurator.css */ |
|
||||
/* Styles for Marlin Configurator */ |
|
||||
|
|
||||
.clear { clear: both; } |
|
||||
|
|
||||
/* Prevent selection except PRE tags */ |
|
||||
* { |
|
||||
-webkit-touch-callout: none; |
|
||||
-webkit-user-select: none; |
|
||||
-khtml-user-select: none; |
|
||||
-moz-user-select: none; |
|
||||
-ms-user-select: none; |
|
||||
user-select: none; |
|
||||
} |
|
||||
pre { |
|
||||
-webkit-touch-callout: text; |
|
||||
-webkit-user-select: text; |
|
||||
-khtml-user-select: text; |
|
||||
-moz-user-select: text; |
|
||||
-ms-user-select: text; |
|
||||
user-select: text; |
|
||||
} |
|
||||
|
|
||||
body { margin: 0; padding: 0; background: #56A; color: #000; font-family: monospace; } |
|
||||
#main { |
|
||||
max-width: 1100px; |
|
||||
margin: 0 auto 10px; |
|
||||
padding: 0 2%; width: 96%; |
|
||||
} |
|
||||
|
|
||||
h1, h2, h3, h4, h5, h6 { clear: both; } |
|
||||
|
|
||||
h1, p.info { font-family: sans-serif; } |
|
||||
h1 { |
|
||||
height: 38px; |
|
||||
margin-bottom: -30px; |
|
||||
color: #FFF; |
|
||||
background: transparent url(logo.png) right top no-repeat; |
|
||||
} |
|
||||
p.info { padding: 0; color: #000; } |
|
||||
p.info span { color: #800; } |
|
||||
|
|
||||
#message { text-align: center; } |
|
||||
#message { width: 80%; margin: 0 auto 0.25em; color: #FF0; } |
|
||||
#message p { padding: 2px 0; font-weight: bold; border-radius: 0.8em; } |
|
||||
#message p.message { color: #080; background: #CFC; } |
|
||||
#message p.error { color: #F00; background: #FF4; } |
|
||||
#message p.warning { color: #FF0; background: #BA4; } |
|
||||
#message p.message span, |
|
||||
#message p.error span, |
|
||||
#message p.warning span { |
|
||||
color: #A00; |
|
||||
background: rgba(255, 255, 255, 1); |
|
||||
border: 1px solid rgba(0,0,0,0.5); |
|
||||
border-radius: 1em; |
|
||||
float: right; |
|
||||
margin-right: 0.5em; |
|
||||
padding: 0 3px; |
|
||||
font-family: sans-serif; |
|
||||
font-size: small; |
|
||||
position: relative; |
|
||||
top: -1px; |
|
||||
} |
|
||||
|
|
||||
#help strong { color: #0DD; } |
|
||||
img { display: none; } |
|
||||
|
|
||||
/* Forms */ |
|
||||
|
|
||||
#config_form { |
|
||||
display: block; |
|
||||
background: #EEE; |
|
||||
padding: 6px 20px 20px; |
|
||||
color: #000; |
|
||||
position: relative; |
|
||||
border-radius: 1.5em; |
|
||||
border-top-left-radius: 0; |
|
||||
} |
|
||||
fieldset { |
|
||||
height: 16.1em; |
|
||||
overflow-y: scroll; |
|
||||
overflow-x: hidden; |
|
||||
margin-top: 10px; |
|
||||
} |
|
||||
label, input, select, textarea { display: block; float: left; margin: 1px 0; } |
|
||||
label.newline, textarea, fieldset { clear: both; } |
|
||||
label { |
|
||||
width: 120px; /* label area */ |
|
||||
height: 1em; |
|
||||
padding: 10px 460px 10px 1em; |
|
||||
margin-right: -450px; |
|
||||
text-align: right; |
|
||||
} |
|
||||
label.blocked, label.added.blocked, label.added.blocked.sublabel { color: #AAA; } |
|
||||
|
|
||||
label.added.sublabel { |
|
||||
width: auto; |
|
||||
margin: 11px -2.5em 0 1em; |
|
||||
padding: 0 3em 0 0; |
|
||||
font-style: italic; |
|
||||
color: #444; |
|
||||
} |
|
||||
label+label.added.sublabel { |
|
||||
margin-left: 0; |
|
||||
} |
|
||||
|
|
||||
input[type="text"], select { margin: 0.75em 0 0; } |
|
||||
input[type="checkbox"], input[type="radio"], input[type="file"] { margin: 1em 0 0; } |
|
||||
input[type="checkbox"].enabler, input[type="radio"].enabler { margin-left: 1em; } |
|
||||
|
|
||||
input:disabled { color: #BBB; } |
|
||||
|
|
||||
#config_form input[type="text"].subitem { width: 4em; } |
|
||||
#config_form input[type="text"].subitem+.subitem { margin-left: 4px; } |
|
||||
|
|
||||
input[type="text"].added { width: 20em; } |
|
||||
label.added { |
|
||||
width: 265px; /* label area */ |
|
||||
height: 1em; |
|
||||
padding: 10px 370px 10px 1em; |
|
||||
margin-right: -360px; |
|
||||
text-align: right; |
|
||||
} |
|
||||
|
|
||||
ul.tabs { padding: 0; list-style: none; } |
|
||||
ul.tabs li { display: inline; } |
|
||||
ul.tabs li a, |
|
||||
ul.tabs li a.active:hover, |
|
||||
ul.tabs li a.active:active { |
|
||||
display: block; |
|
||||
float: left; |
|
||||
background: #1E4059; |
|
||||
color: #CCC; |
|
||||
font-size: 110%; |
|
||||
border-radius: 0.25em 0.25em 0 0; |
|
||||
margin: 0 4px 0 0; |
|
||||
padding: 2px 8px; |
|
||||
text-decoration: none; |
|
||||
font-family: georgia,"times new roman",times; |
|
||||
} |
|
||||
ul.tabs li a.active:link, |
|
||||
ul.tabs li a.active:visited { |
|
||||
background: #DDD; |
|
||||
color: #06F; |
|
||||
cursor: default; |
|
||||
margin-top: -4px; |
|
||||
padding-bottom: 4px; |
|
||||
padding-top: 4px; |
|
||||
} |
|
||||
ul.tabs li a:hover, |
|
||||
ul.tabs li a:active { |
|
||||
background: #000; |
|
||||
color: #FFF; |
|
||||
} |
|
||||
|
|
||||
fieldset { display: none; border: 1px solid #AAA; border-radius: 1em; } |
|
||||
fieldset legend { display: none; } |
|
||||
|
|
||||
.hilightable span { |
|
||||
display: block; |
|
||||
float: left; |
|
||||
width: 100%; |
|
||||
height: 1.3em; |
|
||||
background: rgba(225,255,0,1); |
|
||||
margin: 0 -100% -1em 0; |
|
||||
} |
|
||||
|
|
||||
#serial_stepper { padding-top: 0.75em; display: block; float: left; } |
|
||||
/*#SERIAL_PORT { display: none; }*/ |
|
||||
|
|
||||
/* Tooltips */ |
|
||||
|
|
||||
#tooltip { |
|
||||
display: none; |
|
||||
max-width: 30em; |
|
||||
padding: 8px; |
|
||||
border: 2px solid #73d699; |
|
||||
border-radius: 1em; |
|
||||
position: absolute; |
|
||||
z-index: 999; |
|
||||
font-family: sans-serif; |
|
||||
font-size: 85%; |
|
||||
color: #000; |
|
||||
line-height: 1.1; |
|
||||
background: #e2ff99; /* Old browsers */ |
|
||||
background: -moz-linear-gradient(top, #e2ff99 0%, #73d699 100%); /* FF3.6+ */ |
|
||||
background: -webkit-gradient(linear, left top, left bottom, color-stop(0%,#e2ff99), color-stop(100%,#73d699)); /* Chrome,Safari4+ */ |
|
||||
background: -webkit-linear-gradient(top, #e2ff99 0%,#73d699 100%); /* Chrome10+,Safari5.1+ */ |
|
||||
background: -o-linear-gradient(top, #e2ff99 0%,#73d699 100%); /* Opera 11.10+ */ |
|
||||
background: -ms-linear-gradient(top, #e2ff99 0%,#73d699 100%); /* IE10+ */ |
|
||||
background: linear-gradient(to bottom, #e2ff99 0%,#73d699 100%); /* W3C */ |
|
||||
filter: progid:DXImageTransform.Microsoft.gradient( startColorstr='#e2ff99', endColorstr='#73d699',GradientType=0 ); /* IE6-9 */ |
|
||||
-webkit-box-shadow: 0px 6px 25px -4px rgba(0,0,0,0.75); |
|
||||
-moz-box-shadow: 0px 6px 25px -4px rgba(0,0,0,0.75); |
|
||||
box-shadow: 0px 6px 25px -4px rgba(0,0,0,0.75); |
|
||||
} |
|
||||
#tooltip>span { |
|
||||
position: absolute; |
|
||||
content: ""; |
|
||||
width: 0; |
|
||||
height: 0; |
|
||||
border-left: 8px solid transparent; |
|
||||
border-right: 8px solid transparent; |
|
||||
border-top: 8px solid #73d699; |
|
||||
z-index: 999; |
|
||||
bottom: -10px; |
|
||||
left: 20px; |
|
||||
} |
|
||||
#tooltip>strong { color: #00B; } |
|
||||
|
|
||||
/* Tooltips Checkbox */ |
|
||||
|
|
||||
#tipson { |
|
||||
width: auto; |
|
||||
height: auto; |
|
||||
padding: 0; |
|
||||
margin-right: 0; |
|
||||
float: right; |
|
||||
font-weight: bold; |
|
||||
font-size: 100%; |
|
||||
font-family: helvetica; |
|
||||
text-align: left; |
|
||||
cursor: pointer; |
|
||||
} |
|
||||
#tipson input { float: none; display: inline; cursor: pointer; } |
|
||||
|
|
||||
/* Config Text */ |
|
||||
|
|
||||
pre.config { |
|
||||
height: 25em; |
|
||||
padding: 10px; |
|
||||
border: 2px solid #888; |
|
||||
border-radius: 5px; |
|
||||
overflow: auto; |
|
||||
clear: both; |
|
||||
background-color: #FFF; |
|
||||
color: #000; |
|
||||
font-family: "Fira Mono", monospace; |
|
||||
font-size: small; |
|
||||
} |
|
||||
|
|
||||
/* Pre Headers */ |
|
||||
|
|
||||
h2 { |
|
||||
width: 100%; |
|
||||
margin: 12px -300px 4px 0; |
|
||||
padding: 0; |
|
||||
float: left; |
|
||||
} |
|
||||
|
|
||||
/* Disclosure Widget */ |
|
||||
|
|
||||
span.disclose, a.download, a.download-all {︎ |
|
||||
display: block; |
|
||||
float: right; |
|
||||
margin-top: 12px; |
|
||||
} |
|
||||
|
|
||||
span.disclose { |
|
||||
margin-right: -10px; /* total width */ |
|
||||
margin-left: 14px; |
|
||||
width: 0; |
|
||||
height: 0; |
|
||||
position: relative; |
|
||||
left: 3px; |
|
||||
top: 3px; |
|
||||
cursor: pointer; |
|
||||
border-left: 8px solid transparent; |
|
||||
border-right: 8px solid transparent; |
|
||||
border-top: 10px solid #000; |
|
||||
} |
|
||||
span.disclose.closed { |
|
||||
margin-right: -8px; /* total width */ |
|
||||
margin-left: 10px; |
|
||||
left: 0; |
|
||||
top: 0; |
|
||||
border-top: 8px solid transparent; |
|
||||
border-bottom: 8px solid transparent; |
|
||||
border-right: 10px solid #000; |
|
||||
} |
|
||||
span.disclose.almost { |
|
||||
-ms-transform: rotate(45deg); /* IE 9 */ |
|
||||
-webkit-transform: rotate(45deg); /* Chrome, Safari, Opera */ |
|
||||
transform: rotate(45deg); |
|
||||
} |
|
||||
span.disclose.closed.almost { |
|
||||
left: 1px; |
|
||||
top: 3px; |
|
||||
-ms-transform: rotate(315deg); /* IE 9 */ |
|
||||
-webkit-transform: rotate(315deg); /* Chrome, Safari, Opera */ |
|
||||
transform: rotate(315deg); |
|
||||
} |
|
||||
|
|
||||
/* Download Button */ |
|
||||
|
|
||||
a.download, a.download-all { |
|
||||
visibility: hidden; |
|
||||
padding: 2px; |
|
||||
border: 1px solid #494; |
|
||||
border-radius: 4px; |
|
||||
margin: 12px 0 0; |
|
||||
background: #FFF; |
|
||||
color: #494; |
|
||||
font-family: sans-serif; |
|
||||
font-size: small; |
|
||||
font-weight: bold; |
|
||||
text-decoration: none; |
|
||||
} |
|
||||
a.download-all { margin: 9px 2em 0; color: #449; border-color: #449; } |
|
||||
|
|
||||
input[type="text"].one_of_2 { max-width: 15%; } |
|
||||
input[type="text"].one_of_3 { max-width: 10%; } |
|
||||
input[type="text"].one_of_4 { max-width: 7%; } |
|
||||
|
|
||||
select.one_of_2 { max-width: 15%; } |
|
||||
select.one_of_3 { max-width: 10%; } |
|
||||
select.one_of_4 { max-width: 14%; } |
|
||||
select.one_of_4+span.label+select.one_of_4+span.label { clear: both; margin-left: 265px; padding-left: 1.75em; } |
|
||||
select.one_of_4+span.label+select.one_of_4+span.label+select.one_of_4+span.label { clear: none; margin-left: 1em; padding-left: 0; } |
|
||||
|
|
||||
@media all and (min-width: 1140px) { |
|
||||
|
|
||||
#main { max-width: 10000px; } |
|
||||
|
|
||||
fieldset { float: left; width: 50%; height: auto; } |
|
||||
|
|
||||
#config_text, #config_adv_text { float: right; clear: right; width: 45%; } |
|
||||
|
|
||||
pre.config { height: 20em; } |
|
||||
|
|
||||
.disclose { display: none; } |
|
||||
|
|
||||
input[type="text"].one_of_2 { max-width: 15%; } |
|
||||
input[type="text"].one_of_3 { max-width: 9%; } |
|
||||
input[type="text"].one_of_4 { max-width: 8%; } |
|
||||
|
|
||||
select.one_of_2 { max-width: 15%; } |
|
||||
select.one_of_3 { max-width: 10%; } |
|
||||
select.one_of_4 { max-width: 16%; } |
|
||||
|
|
||||
} |
|
||||
|
|
||||
/*label.blocked, .blocked { display: none; }*/ |
|
||||
|
|
||||
|
Before Width: | Height: | Size: 1.2 KiB |
@ -1,129 +0,0 @@ |
|||||
<!DOCTYPE html> |
|
||||
<html> |
|
||||
<head> |
|
||||
<meta charset="UTF-8"> |
|
||||
<title>Marlin Firmware Configurator</title> |
|
||||
<link href='http://fonts.googleapis.com/css?family=Fira+Mono&subset=latin,latin-ext' rel='stylesheet' type='text/css' /> |
|
||||
<script src="js/jquery-2.1.3.min.js"></script> |
|
||||
<script src="js/binarystring.js"></script> |
|
||||
<script src="js/binaryfileuploader.js"></script> |
|
||||
<script src="js/FileSaver.min.js"></script> |
|
||||
<script src="js/jszip.min.js"></script> |
|
||||
<script src="js/jcanvas.js"></script> |
|
||||
<script src="js/jstepper.js"></script> |
|
||||
<script src="js/configurator.js"></script> |
|
||||
<link rel="stylesheet" href="css/configurator.css" type="text/css" media="all" /> |
|
||||
</head> |
|
||||
<body> |
|
||||
<section id="main"> |
|
||||
<h1>Marlin Configurator</h1> |
|
||||
<p class="info">Select presets (coming soon), modify, and download.</p> |
|
||||
|
|
||||
<div id="message"></div> |
|
||||
<div id="tabs"></div> |
|
||||
|
|
||||
<form id="config_form"> |
|
||||
|
|
||||
<div id="tooltip"></div> |
|
||||
|
|
||||
<label>Drop Files:</label><input type="file" id="file-upload" /> |
|
||||
<label id="tipson"><input type="checkbox" checked /> ?</label> |
|
||||
<a href="" class="download-all">Download Zip</a> |
|
||||
|
|
||||
<fieldset id="info"> |
|
||||
<legend>Info</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="machine"> |
|
||||
<legend>Machine</legend> |
|
||||
|
|
||||
<label class="newline">Serial Port:</label><select name="SERIAL_PORT"></select><div id="serial_stepper"></div> |
|
||||
|
|
||||
<label>Baud Rate:</label><select name="BAUDRATE"></select> |
|
||||
|
|
||||
<label>AT90USB BT IF:</label> |
|
||||
<input name="BLUETOOTH" type="checkbox" value="1" checked /> |
|
||||
|
|
||||
<label class="newline">Motherboard:</label><select name="MOTHERBOARD"></select> |
|
||||
|
|
||||
<label class="newline">Custom Name:</label><input name="CUSTOM_MACHINE_NAME" type="text" size="14" maxlength="12" value="" /> |
|
||||
|
|
||||
<label class="newline">Machine UUID:</label><input name="MACHINE_UUID" type="text" size="38" maxlength="36" value="" /> |
|
||||
|
|
||||
<label class="newline">Extruders:</label><select name="EXTRUDERS"></select> |
|
||||
|
|
||||
<label class="newline">Power Supply:</label><select name="POWER_SUPPLY"></select> |
|
||||
|
|
||||
<label>PS Default Off:</label> |
|
||||
<input name="PS_DEFAULT_OFF" type="checkbox" value="1" checked /> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="homing"> |
|
||||
<legend>Homing</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="temperature"> |
|
||||
<legend>Temperature</legend> |
|
||||
<label class="newline">Temp Sensor 0:</label><select name="TEMP_SENSOR_0"></select> |
|
||||
<label class="newline">Temp Sensor 1:</label><select name="TEMP_SENSOR_1"></select> |
|
||||
<label class="newline">Temp Sensor 2:</label><select name="TEMP_SENSOR_2"></select> |
|
||||
<label class="newline">Bed Temp Sensor:</label><select name="TEMP_SENSOR_BED"></select> |
|
||||
|
|
||||
<label>Max Diff:</label> |
|
||||
<input name="MAX_REDUNDANT_TEMP_SENSOR_DIFF" type="text" size="3" maxlength="2" /> |
|
||||
|
|
||||
<label>Temp Residency Time (s):</label> |
|
||||
<input name="TEMP_RESIDENCY_TIME" type="text" size="3" maxlength="2" /> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="extruder"> |
|
||||
<legend>Extruder</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="lcd"> |
|
||||
<legend>LCD / SD</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="bedlevel"> |
|
||||
<legend>Bed Leveling</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="fwretract"> |
|
||||
<legend>FW Retract</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="tmc"> |
|
||||
<legend>TMC</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="l6470"> |
|
||||
<legend>L6470</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="extras"> |
|
||||
<legend>Extras</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<fieldset id="more"> |
|
||||
<legend>More…</legend> |
|
||||
</fieldset> |
|
||||
|
|
||||
<section id="config_text"> |
|
||||
<h2>Configuration.h</h2> |
|
||||
<span class="disclose"></span> |
|
||||
<a href="" class="download">Download</a> |
|
||||
<pre class="hilightable config"></pre> |
|
||||
</section> |
|
||||
|
|
||||
<section id="config_adv_text"> |
|
||||
<h2>Configuration_adv.h</h2> |
|
||||
<span class="disclose"></span> |
|
||||
<a href="" class="download">Download</a> |
|
||||
<pre class="hilightable config"></pre> |
|
||||
</section> |
|
||||
|
|
||||
<br class="clear" /> |
|
||||
</form> |
|
||||
</section> |
|
||||
</body> |
|
||||
</html> |
|
||||
@ -1,2 +0,0 @@ |
|||||
/*! @source http://purl.eligrey.com/github/FileSaver.js/blob/master/FileSaver.js */ |
|
||||
var saveAs=saveAs||typeof navigator!=="undefined"&&navigator.msSaveOrOpenBlob&&navigator.msSaveOrOpenBlob.bind(navigator)||function(view){"use strict";if(typeof navigator!=="undefined"&&/MSIE [1-9]\./.test(navigator.userAgent)){return}var doc=view.document,get_URL=function(){return view.URL||view.webkitURL||view},save_link=doc.createElementNS("http://www.w3.org/1999/xhtml","a"),can_use_save_link="download"in save_link,click=function(node){var event=doc.createEvent("MouseEvents");event.initMouseEvent("click",true,false,view,0,0,0,0,0,false,false,false,false,0,null);node.dispatchEvent(event)},webkit_req_fs=view.webkitRequestFileSystem,req_fs=view.requestFileSystem||webkit_req_fs||view.mozRequestFileSystem,throw_outside=function(ex){(view.setImmediate||view.setTimeout)(function(){throw ex},0)},force_saveable_type="application/octet-stream",fs_min_size=0,arbitrary_revoke_timeout=500,revoke=function(file){var revoker=function(){if(typeof file==="string"){get_URL().revokeObjectURL(file)}else{file.remove()}};if(view.chrome){revoker()}else{setTimeout(revoker,arbitrary_revoke_timeout)}},dispatch=function(filesaver,event_types,event){event_types=[].concat(event_types);var i=event_types.length;while(i--){var listener=filesaver["on"+event_types[i]];if(typeof listener==="function"){try{listener.call(filesaver,event||filesaver)}catch(ex){throw_outside(ex)}}}},FileSaver=function(blob,name){var filesaver=this,type=blob.type,blob_changed=false,object_url,target_view,dispatch_all=function(){dispatch(filesaver,"writestart progress write writeend".split(" "))},fs_error=function(){if(blob_changed||!object_url){object_url=get_URL().createObjectURL(blob)}if(target_view){target_view.location.href=object_url}else{var new_tab=view.open(object_url,"_blank");if(new_tab==undefined&&typeof safari!=="undefined"){view.location.href=object_url}}filesaver.readyState=filesaver.DONE;dispatch_all();revoke(object_url)},abortable=function(func){return function(){if(filesaver.readyState!==filesaver.DONE){return func.apply(this,arguments)}}},create_if_not_found={create:true,exclusive:false},slice;filesaver.readyState=filesaver.INIT;if(!name){name="download"}if(can_use_save_link){object_url=get_URL().createObjectURL(blob);save_link.href=object_url;save_link.download=name;click(save_link);filesaver.readyState=filesaver.DONE;dispatch_all();revoke(object_url);return}if(view.chrome&&type&&type!==force_saveable_type){slice=blob.slice||blob.webkitSlice;blob=slice.call(blob,0,blob.size,force_saveable_type);blob_changed=true}if(webkit_req_fs&&name!=="download"){name+=".download"}if(type===force_saveable_type||webkit_req_fs){target_view=view}if(!req_fs){fs_error();return}fs_min_size+=blob.size;req_fs(view.TEMPORARY,fs_min_size,abortable(function(fs){fs.root.getDirectory("saved",create_if_not_found,abortable(function(dir){var save=function(){dir.getFile(name,create_if_not_found,abortable(function(file){file.createWriter(abortable(function(writer){writer.onwriteend=function(event){target_view.location.href=file.toURL();filesaver.readyState=filesaver.DONE;dispatch(filesaver,"writeend",event);revoke(file)};writer.onerror=function(){var error=writer.error;if(error.code!==error.ABORT_ERR){fs_error()}};"writestart progress write abort".split(" ").forEach(function(event){writer["on"+event]=filesaver["on"+event]});writer.write(blob);filesaver.abort=function(){writer.abort();filesaver.readyState=filesaver.DONE};filesaver.readyState=filesaver.WRITING}),fs_error)}),fs_error)};dir.getFile(name,{create:false},abortable(function(file){file.remove();save()}),abortable(function(ex){if(ex.code===ex.NOT_FOUND_ERR){save()}else{fs_error()}}))}),fs_error)}),fs_error)},FS_proto=FileSaver.prototype,saveAs=function(blob,name){return new FileSaver(blob,name)};FS_proto.abort=function(){var filesaver=this;filesaver.readyState=filesaver.DONE;dispatch(filesaver,"abort")};FS_proto.readyState=FS_proto.INIT=0;FS_proto.WRITING=1;FS_proto.DONE=2;FS_proto.error=FS_proto.onwritestart=FS_proto.onprogress=FS_proto.onwrite=FS_proto.onabort=FS_proto.onerror=FS_proto.onwriteend=null;return saveAs}(typeof self!=="undefined"&&self||typeof window!=="undefined"&&window||this.content);if(typeof module!=="undefined"&&module.exports){module.exports.saveAs=saveAs}else if(typeof define!=="undefined"&&define!==null&&define.amd!=null){define([],function(){return saveAs})} |
|
||||
@ -1,79 +0,0 @@ |
|||||
function BinaryFileUploader(o) { |
|
||||
this.options = null; |
|
||||
|
|
||||
|
|
||||
this._defaultOptions = { |
|
||||
element: null, // HTML file element
|
|
||||
onFileLoad: function(file) { |
|
||||
console.log(file.toString()); |
|
||||
} |
|
||||
}; |
|
||||
|
|
||||
|
|
||||
this._init = function(o) { |
|
||||
if (!this.hasFileUploaderSupport()) return; |
|
||||
|
|
||||
this._verifyDependencies(); |
|
||||
|
|
||||
this.options = this._mergeObjects(this._defaultOptions, o); |
|
||||
this._verifyOptions(); |
|
||||
|
|
||||
this.addFileChangeListener(); |
|
||||
} |
|
||||
|
|
||||
|
|
||||
this.hasFileUploaderSupport = function() { |
|
||||
return !!(window.File && window.FileReader && window.FileList && window.Blob); |
|
||||
} |
|
||||
|
|
||||
this.addFileChangeListener = function() { |
|
||||
this.options.element.addEventListener( |
|
||||
'change', |
|
||||
this._bind(this, this.onFileChange) |
|
||||
); |
|
||||
} |
|
||||
|
|
||||
this.onFileChange = function(e) { |
|
||||
// TODO accept multiple files
|
|
||||
var file = e.target.files[0], |
|
||||
reader = new FileReader(); |
|
||||
|
|
||||
reader.onload = this._bind(this, this.onFileLoad); |
|
||||
reader.readAsBinaryString(file); |
|
||||
} |
|
||||
|
|
||||
this.onFileLoad = function(e) { |
|
||||
var content = e.target.result, |
|
||||
string = new BinaryString(content); |
|
||||
this.options.onFileLoad(string); |
|
||||
} |
|
||||
|
|
||||
|
|
||||
this._mergeObjects = function(starting, override) { |
|
||||
var merged = starting; |
|
||||
for (key in override) merged[key] = override[key]; |
|
||||
|
|
||||
return merged; |
|
||||
} |
|
||||
|
|
||||
this._verifyOptions = function() { |
|
||||
if (!(this.options.element && this.options.element.type && this.options.element.type === 'file')) { |
|
||||
throw 'Invalid element param in options. Must be a file upload DOM element'; |
|
||||
} |
|
||||
|
|
||||
if (typeof this.options.onFileLoad !== 'function') { |
|
||||
throw 'Invalid onFileLoad param in options. Must be a function'; |
|
||||
} |
|
||||
} |
|
||||
|
|
||||
this._verifyDependencies = function() { |
|
||||
if (!window.BinaryString) throw 'BinaryString is missing. Check that you\'ve correctly included it'; |
|
||||
} |
|
||||
|
|
||||
// helper function for binding methods to objects
|
|
||||
this._bind = function(object, method) { |
|
||||
return function() {return method.apply(object, arguments);}; |
|
||||
} |
|
||||
|
|
||||
this._init(o); |
|
||||
} |
|
||||
@ -1,168 +0,0 @@ |
|||||
function BinaryString(source) { |
|
||||
this._source = null; |
|
||||
this._bytes = []; |
|
||||
this._pos = 0; |
|
||||
this._length = 0; |
|
||||
|
|
||||
this._init = function(source) { |
|
||||
this._source = source; |
|
||||
this._bytes = this._stringToBytes(this._source); |
|
||||
this._length = this._bytes.length; |
|
||||
} |
|
||||
|
|
||||
this.current = function() {return this._pos;} |
|
||||
|
|
||||
this.rewind = function() {return this.jump(0);} |
|
||||
this.end = function() {return this.jump(this.length() - 1);} |
|
||||
this.next = function() {return this.jump(this.current() + 1);} |
|
||||
this.prev = function() {return this.jump(this.current() - 1);} |
|
||||
|
|
||||
this.jump = function(pos) { |
|
||||
if (pos < 0 || pos >= this.length()) return false; |
|
||||
|
|
||||
this._pos = pos; |
|
||||
return true; |
|
||||
} |
|
||||
|
|
||||
this.readByte = function(pos) { |
|
||||
pos = (typeof pos == 'number') ? pos : this.current(); |
|
||||
return this.readBytes(1, pos)[0]; |
|
||||
} |
|
||||
|
|
||||
this.readBytes = function(length, pos) { |
|
||||
length = length || 1; |
|
||||
pos = (typeof pos == 'number') ? pos : this.current(); |
|
||||
|
|
||||
if (pos > this.length() || |
|
||||
pos < 0 || |
|
||||
length <= 0 || |
|
||||
pos + length > this.length() || |
|
||||
pos + length < 0 |
|
||||
) { |
|
||||
return false; |
|
||||
} |
|
||||
|
|
||||
var bytes = []; |
|
||||
|
|
||||
for (var i = pos; i < pos + length; i++) { |
|
||||
bytes.push(this._bytes[i]); |
|
||||
} |
|
||||
|
|
||||
return bytes; |
|
||||
} |
|
||||
|
|
||||
this.length = function() {return this._length;} |
|
||||
|
|
||||
this.toString = function() { |
|
||||
var string = '', |
|
||||
length = this.length(); |
|
||||
|
|
||||
for (var i = 0; i < length; i++) { |
|
||||
string += String.fromCharCode(this.readByte(i)); |
|
||||
} |
|
||||
|
|
||||
return string; |
|
||||
} |
|
||||
|
|
||||
this.toUtf8 = function() { |
|
||||
var inc = 0, |
|
||||
string = '', |
|
||||
length = this.length(); |
|
||||
|
|
||||
// determine if first 3 characters are the BOM
|
|
||||
// then skip them in output if so
|
|
||||
if (length >= 3 && |
|
||||
this.readByte(0) === 0xEF && |
|
||||
this.readByte(1) === 0xBB && |
|
||||
this.readByte(2) === 0xBF |
|
||||
) { |
|
||||
inc = 3; |
|
||||
} |
|
||||
|
|
||||
for (; inc < length; inc++) { |
|
||||
var byte1 = this.readByte(inc), |
|
||||
byte2 = 0, |
|
||||
byte3 = 0, |
|
||||
byte4 = 0, |
|
||||
code1 = 0, |
|
||||
code2 = 0, |
|
||||
point = 0; |
|
||||
|
|
||||
switch (true) { |
|
||||
// single byte character; same as ascii
|
|
||||
case (byte1 < 0x80): |
|
||||
code1 = byte1; |
|
||||
break; |
|
||||
|
|
||||
// 2 byte character
|
|
||||
case (byte1 >= 0xC2 && byte1 < 0xE0): |
|
||||
byte2 = this.readByte(++inc); |
|
||||
|
|
||||
code1 = ((byte1 & 0x1F) << 6) + |
|
||||
(byte2 & 0x3F); |
|
||||
break; |
|
||||
|
|
||||
// 3 byte character
|
|
||||
case (byte1 >= 0xE0 && byte1 < 0xF0): |
|
||||
byte2 = this.readByte(++inc); |
|
||||
byte3 = this.readByte(++inc); |
|
||||
|
|
||||
code1 = ((byte1 & 0xFF) << 12) + |
|
||||
((byte2 & 0x3F) << 6) + |
|
||||
(byte3 & 0x3F); |
|
||||
break; |
|
||||
|
|
||||
// 4 byte character
|
|
||||
case (byte1 >= 0xF0 && byte1 < 0xF5): |
|
||||
byte2 = this.readByte(++inc); |
|
||||
byte3 = this.readByte(++inc); |
|
||||
byte4 = this.readByte(++inc); |
|
||||
|
|
||||
point = ((byte1 & 0x07) << 18) + |
|
||||
((byte2 & 0x3F) << 12) + |
|
||||
((byte3 & 0x3F) << 6) + |
|
||||
(byte4 & 0x3F) |
|
||||
point -= 0x10000; |
|
||||
|
|
||||
code1 = (point >> 10) + 0xD800; |
|
||||
code2 = (point & 0x3FF) + 0xDC00; |
|
||||
break; |
|
||||
|
|
||||
default: |
|
||||
throw 'Invalid byte ' + this._byteToString(byte1) + ' whilst converting to UTF-8'; |
|
||||
break; |
|
||||
} |
|
||||
|
|
||||
string += (code2) ? String.fromCharCode(code1, code2) |
|
||||
: String.fromCharCode(code1); |
|
||||
} |
|
||||
|
|
||||
return string; |
|
||||
} |
|
||||
|
|
||||
this.toArray = function() {return this.readBytes(this.length() - 1, 0);} |
|
||||
|
|
||||
|
|
||||
this._stringToBytes = function(str) { |
|
||||
var bytes = [], |
|
||||
chr = 0; |
|
||||
|
|
||||
for (var i = 0; i < str.length; i++) { |
|
||||
chr = str.charCodeAt(i); |
|
||||
bytes.push(chr & 0xFF); |
|
||||
} |
|
||||
|
|
||||
return bytes; |
|
||||
} |
|
||||
|
|
||||
this._byteToString = function(byte) { |
|
||||
var asString = byte.toString(16).toUpperCase(); |
|
||||
while (asString.length < 2) { |
|
||||
asString = '0' + asString; |
|
||||
} |
|
||||
|
|
||||
return '0x' + asString; |
|
||||
} |
|
||||
|
|
||||
this._init(source); |
|
||||
} |
|
||||
File diff suppressed because it is too large
@ -1,524 +0,0 @@ |
|||||
/*! |
|
||||
jCanvas v2.2.1 |
|
||||
Caleb Evans |
|
||||
2.2.1 revisions by Thinkyhead |
|
||||
*/ |
|
||||
|
|
||||
(function($, document, Math, Number, undefined) { |
|
||||
|
|
||||
// jC global object
|
|
||||
var jC = {}; |
|
||||
jC.originals = { |
|
||||
width: 20, |
|
||||
height: 20, |
|
||||
cornerRadius: 0, |
|
||||
fillStyle: 'transparent', |
|
||||
strokeStyle: 'transparent', |
|
||||
strokeWidth: 5, |
|
||||
strokeCap: 'butt', |
|
||||
strokeJoin: 'miter', |
|
||||
shadowX: 0, |
|
||||
shadowY: 0, |
|
||||
shadowBlur: 10, |
|
||||
shadowColor: 'transparent', |
|
||||
x: 0, y: 0, |
|
||||
x1: 0, y1: 0, |
|
||||
radius: 10, |
|
||||
start: 0, |
|
||||
end: 360, |
|
||||
ccw: false, |
|
||||
inDegrees: true, |
|
||||
fromCenter: true, |
|
||||
closed: false, |
|
||||
sides: 3, |
|
||||
angle: 0, |
|
||||
text: '', |
|
||||
font: 'normal 12pt sans-serif', |
|
||||
align: 'center', |
|
||||
baseline: 'middle', |
|
||||
source: '', |
|
||||
repeat: 'repeat' |
|
||||
}; |
|
||||
// Duplicate original defaults
|
|
||||
jC.defaults = $.extend({}, jC.originals); |
|
||||
|
|
||||
// Set global properties
|
|
||||
function setGlobals(context, map) { |
|
||||
context.fillStyle = map.fillStyle; |
|
||||
context.strokeStyle = map.strokeStyle; |
|
||||
context.lineWidth = map.strokeWidth; |
|
||||
context.lineCap = map.strokeCap; |
|
||||
context.lineJoin = map.strokeJoin; |
|
||||
context.shadowOffsetX = map.shadowX; |
|
||||
context.shadowOffsetY = map.shadowY; |
|
||||
context.shadowBlur = map.shadowBlur; |
|
||||
context.shadowColor = map.shadowColor; |
|
||||
} |
|
||||
|
|
||||
// Close path if chosen
|
|
||||
function closePath(context, map) { |
|
||||
if (map.closed === true) { |
|
||||
context.closePath(); |
|
||||
context.fill(); |
|
||||
context.stroke(); |
|
||||
} else { |
|
||||
context.fill(); |
|
||||
context.stroke(); |
|
||||
context.closePath(); |
|
||||
} |
|
||||
} |
|
||||
|
|
||||
// Measure angles in degrees if chosen
|
|
||||
function checkUnits(map) { |
|
||||
if (map.inDegrees === true) { |
|
||||
return Math.PI / 180; |
|
||||
} else { |
|
||||
return 1; |
|
||||
} |
|
||||
} |
|
||||
|
|
||||
// Set canvas defaults
|
|
||||
$.fn.canvas = function(args) { |
|
||||
// Reset defaults if no value is passed
|
|
||||
if (typeof args === 'undefined') { |
|
||||
jC.defaults = jC.originals; |
|
||||
} else { |
|
||||
jC.defaults = $.extend({}, jC.defaults, args); |
|
||||
} |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Load canvas
|
|
||||
$.fn.loadCanvas = function(context) { |
|
||||
if (typeof context === 'undefined') {context = '2d';} |
|
||||
return this[0].getContext(context); |
|
||||
}; |
|
||||
|
|
||||
// Create gradient
|
|
||||
$.fn.gradient = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
// Specify custom defaults
|
|
||||
gDefaults = { |
|
||||
x1: 0, y1: 0, |
|
||||
x2: 0, y2: 0, |
|
||||
r1: 10, r2: 100 |
|
||||
}, |
|
||||
params = $.extend({}, gDefaults, args), |
|
||||
gradient, stops = 0, percent, i; |
|
||||
|
|
||||
// Create radial gradient if chosen
|
|
||||
if (typeof args.r1 === 'undefined' && typeof args.r2 === 'undefined') { |
|
||||
gradient = ctx.createLinearGradient(params.x1, params.y1, params.x2, params.y2); |
|
||||
} else { |
|
||||
gradient = ctx.createRadialGradient(params.x1, params.y1, params.r1, params.x2, params.y2, params.r2); |
|
||||
} |
|
||||
|
|
||||
// Count number of color stops
|
|
||||
for (i=1; i<=Number.MAX_VALUE; i+=1) { |
|
||||
if (params['c' + i]) { |
|
||||
stops += 1; |
|
||||
} else { |
|
||||
break; |
|
||||
} |
|
||||
} |
|
||||
|
|
||||
// Calculate color stop percentages if absent
|
|
||||
for (i=1; i<=stops; i+=1) { |
|
||||
percent = Math.round((100 / (stops-1)) * (i-1)) / 100; |
|
||||
if (typeof params['s' + i] === 'undefined') { |
|
||||
params['s' + i] = percent; |
|
||||
} |
|
||||
gradient.addColorStop(params['s' + i], params['c' + i]); |
|
||||
} |
|
||||
return gradient; |
|
||||
}; |
|
||||
|
|
||||
// Create pattern
|
|
||||
$.fn.pattern = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
pattern, |
|
||||
img = document.createElement('img'); |
|
||||
img.src = params.source; |
|
||||
|
|
||||
// Create pattern
|
|
||||
function create() { |
|
||||
if (img.complete === true) { |
|
||||
// Create pattern
|
|
||||
pattern = ctx.createPattern(img, params.repeat); |
|
||||
} else { |
|
||||
throw "The pattern has not loaded yet"; |
|
||||
} |
|
||||
} |
|
||||
try { |
|
||||
create(); |
|
||||
} catch(error) { |
|
||||
img.onload = create; |
|
||||
} |
|
||||
return pattern; |
|
||||
}; |
|
||||
|
|
||||
// Clear canvas
|
|
||||
$.fn.clearCanvas = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args); |
|
||||
|
|
||||
// Draw from center if chosen
|
|
||||
if (params.fromCenter === true) { |
|
||||
params.x -= params.width / 2; |
|
||||
params.y -= params.height / 2; |
|
||||
} |
|
||||
|
|
||||
// Clear entire canvas if chosen
|
|
||||
ctx.beginPath(); |
|
||||
if (typeof args === 'undefined') { |
|
||||
ctx.clearRect(0, 0, this.width(), this.height()); |
|
||||
} else { |
|
||||
ctx.clearRect(params.x, params.y, params.width, params.height); |
|
||||
} |
|
||||
ctx.closePath(); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Save canvas
|
|
||||
$.fn.saveCanvas = function() { |
|
||||
var ctx = this.loadCanvas(); |
|
||||
ctx.save(); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Restore canvas
|
|
||||
$.fn.restoreCanvas = function() { |
|
||||
var ctx = this.loadCanvas(); |
|
||||
ctx.restore(); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Scale canvas
|
|
||||
$.fn.scaleCanvas = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args); |
|
||||
ctx.save(); |
|
||||
ctx.translate(params.x, params.y); |
|
||||
ctx.scale(params.width, params.height); |
|
||||
ctx.translate(-params.x, -params.y) |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Translate canvas
|
|
||||
$.fn.translateCanvas = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args); |
|
||||
ctx.save(); |
|
||||
ctx.translate(params.x, params.y); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Rotate canvas
|
|
||||
$.fn.rotateCanvas = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
toRad = checkUnits(params); |
|
||||
|
|
||||
ctx.save(); |
|
||||
ctx.translate(params.x, params.y); |
|
||||
ctx.rotate(params.angle * toRad); |
|
||||
ctx.translate(-params.x, -params.y); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw rectangle
|
|
||||
$.fn.drawRect = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
toRad = checkUnits(params), |
|
||||
x1, y1, x2, y2, r; |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw from center if chosen
|
|
||||
if (params.fromCenter === true) { |
|
||||
params.x -= params.width / 2; |
|
||||
params.y -= params.height / 2; |
|
||||
} |
|
||||
|
|
||||
// Draw rounded rectangle if chosen
|
|
||||
if (params.cornerRadius > 0) { |
|
||||
x1 = params.x; |
|
||||
y1 = params.y; |
|
||||
x2 = params.x + params.width; |
|
||||
y2 = params.y + params.height; |
|
||||
r = params.cornerRadius; |
|
||||
if ((x2 - x1) - (2 * r) < 0) { |
|
||||
r = (x2 - x1) / 2; |
|
||||
} |
|
||||
if ((y2 - y1) - (2 * r) < 0) { |
|
||||
r = (y2 - y1) / 2; |
|
||||
} |
|
||||
ctx.beginPath(); |
|
||||
ctx.moveTo(x1+r,y1); |
|
||||
ctx.lineTo(x2-r,y1); |
|
||||
ctx.arc(x2-r, y1+r, r, 270*toRad, 360*toRad, false); |
|
||||
ctx.lineTo(x2,y2-r); |
|
||||
ctx.arc(x2-r, y2-r, r, 0, 90*toRad, false); |
|
||||
ctx.lineTo(x1+r,y2); |
|
||||
ctx.arc(x1+r, y2-r, r, 90*toRad, 180*toRad, false); |
|
||||
ctx.lineTo(x1,y1+r); |
|
||||
ctx.arc(x1+r, y1+r, r, 180*toRad, 270*toRad, false); |
|
||||
ctx.fill(); |
|
||||
ctx.stroke(); |
|
||||
ctx.closePath(); |
|
||||
} else { |
|
||||
ctx.fillRect(params.x, params.y, params.width, params.height); |
|
||||
ctx.strokeRect(params.x, params.y, params.width, params.height); |
|
||||
} |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw arc
|
|
||||
$.fn.drawArc = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
toRad = checkUnits(params); |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw from center if chosen
|
|
||||
if (params.fromCenter === false) { |
|
||||
params.x += params.radius; |
|
||||
params.y += params.radius; |
|
||||
} |
|
||||
|
|
||||
ctx.beginPath(); |
|
||||
ctx.arc(params.x, params.y, params.radius, (params.start*toRad)-(Math.PI/2), (params.end*toRad)-(Math.PI/2), params.ccw); |
|
||||
// Close path if chosen
|
|
||||
closePath(ctx, params); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw ellipse
|
|
||||
$.fn.drawEllipse = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
controlW = params.width * (4/3); |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw from center if chosen
|
|
||||
if (params.fromCenter === false) { |
|
||||
params.x += params.width / 2; |
|
||||
params.y += params.height / 2; |
|
||||
} |
|
||||
|
|
||||
// Increment coordinates to prevent negative values
|
|
||||
params.x += 1e-10; |
|
||||
params.y += 1e-10; |
|
||||
|
|
||||
// Create ellipse
|
|
||||
ctx.beginPath(); |
|
||||
ctx.moveTo(params.x, params.y-params.height/2); |
|
||||
ctx.bezierCurveTo(params.x-controlW/2,params.y-params.height/2, |
|
||||
params.x-controlW/2,params.y+params.height/2, |
|
||||
params.x,params.y+params.height/2); |
|
||||
ctx.bezierCurveTo(params.x+controlW/2,params.y+params.height/2, |
|
||||
params.x+controlW/2,params.y-params.height/2, |
|
||||
params.x,params.y-params.height/2); |
|
||||
ctx.closePath(); |
|
||||
ctx.fill(); |
|
||||
ctx.stroke(); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw line
|
|
||||
$.fn.drawLine = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
max = Number.MAX_VALUE, l, |
|
||||
lx, ly; |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw each point
|
|
||||
ctx.beginPath(); |
|
||||
ctx.moveTo(params.x1, params.y1); |
|
||||
for (l=2; l<max; l+=1) { |
|
||||
lx = params['x' + l]; |
|
||||
ly = params['y' + l]; |
|
||||
// Stop loop when all points are drawn
|
|
||||
if (typeof lx === 'undefined' || typeof ly === 'undefined') { |
|
||||
break; |
|
||||
} |
|
||||
ctx.lineTo(lx, ly); |
|
||||
} |
|
||||
// Close path if chosen
|
|
||||
closePath(ctx, params); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw quadratic curve
|
|
||||
$.fn.drawQuad = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
max = Number.MAX_VALUE, l, |
|
||||
lx, ly, lcx, lcy; |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw each point
|
|
||||
ctx.beginPath(); |
|
||||
ctx.moveTo(params.x1, params.y1); |
|
||||
for (l=2; l<max; l+=1) { |
|
||||
lx = params['x' + l]; |
|
||||
if (typeof lx === 'undefined') break; |
|
||||
ly = params['y' + l]; |
|
||||
if (typeof ly === 'undefined') break; |
|
||||
lcx = params['cx' + (l-1)]; |
|
||||
if (typeof lcx === 'undefined') break; |
|
||||
lcy = params['cy' + (l-1)]; |
|
||||
if (typeof lcy === 'undefined') break; |
|
||||
ctx.quadraticCurveTo(lcx, lcy, lx, ly); |
|
||||
} |
|
||||
// Close path if chosen
|
|
||||
closePath(ctx, params); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw Bezier curve
|
|
||||
$.fn.drawBezier = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
max = Number.MAX_VALUE, |
|
||||
l=2, lc=1, lx, ly, lcx1, lcy1, lcx2, lcy2, i; |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw each point
|
|
||||
ctx.beginPath(); |
|
||||
ctx.moveTo(params.x1, params.y1); |
|
||||
for (i=2; i<max; i+=1) { |
|
||||
lx = params['x' + l]; |
|
||||
if (typeof lx === 'undefined') break; |
|
||||
ly = params['y' + l]; |
|
||||
if (typeof ly === 'undefined') break; |
|
||||
lcx1 = params['cx' + lc]; |
|
||||
if (typeof lcx1 === 'undefined') break; |
|
||||
lcy1 = params['cy' + lc]; |
|
||||
if (typeof lcy1 === 'undefined') break; |
|
||||
lcx2 = params['cx' + (lc+1)]; |
|
||||
if (typeof lcx2 === 'undefined') break; |
|
||||
lcy2 = params['cy' + (lc+1)]; |
|
||||
if (typeof lcy2 === 'undefined') break; |
|
||||
ctx.bezierCurveTo(lcx1, lcy1, lcx2, lcy2, lx, ly); |
|
||||
l += 1; |
|
||||
lc += 2; |
|
||||
} |
|
||||
// Close path if chosen
|
|
||||
closePath(ctx, params); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw text
|
|
||||
$.fn.drawText = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args); |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Set text-specific properties
|
|
||||
ctx.textBaseline = params.baseline; |
|
||||
ctx.textAlign = params.align; |
|
||||
ctx.font = params.font; |
|
||||
|
|
||||
ctx.strokeText(params.text, params.x, params.y); |
|
||||
ctx.fillText(params.text, params.x, params.y); |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw image
|
|
||||
$.fn.drawImage = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
// Define image source
|
|
||||
img = document.createElement('img'); |
|
||||
img.src = params.source; |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
// Draw image function
|
|
||||
function draw() { |
|
||||
if (img.complete) { |
|
||||
|
|
||||
var scaleFac = img.width / img.height; |
|
||||
|
|
||||
// If width/height are specified
|
|
||||
if (typeof args.width !== 'undefined' && typeof args.height !== 'undefined') { |
|
||||
img.width = args.width; |
|
||||
img.height = args.height; |
|
||||
// If width is specified
|
|
||||
} else if (typeof args.width !== 'undefined' && typeof args.height === 'undefined') { |
|
||||
img.width = args.width; |
|
||||
img.height = img.width / scaleFac; |
|
||||
// If height is specified
|
|
||||
} else if (typeof args.width === 'undefined' && typeof args.height !== 'undefined') { |
|
||||
img.height = args.height; |
|
||||
img.width = img.height * scaleFac; |
|
||||
} |
|
||||
|
|
||||
// Draw from center if chosen
|
|
||||
if (params.fromCenter === true) { |
|
||||
params.x -= img.width / 2; |
|
||||
params.y -= img.height / 2; |
|
||||
} |
|
||||
|
|
||||
// Draw image
|
|
||||
ctx.drawImage(img, params.x, params.y, img.width, img.height); |
|
||||
} else { |
|
||||
throw "The image has not loaded yet."; |
|
||||
} |
|
||||
} |
|
||||
|
|
||||
function dodraw() { |
|
||||
// console.log("dodraw...");
|
|
||||
try { |
|
||||
// console.log("dodraw...try...");
|
|
||||
draw(); |
|
||||
} |
|
||||
catch(error) { |
|
||||
// console.log("dodraw...catch: " + error);
|
|
||||
} |
|
||||
} |
|
||||
|
|
||||
// Draw image if already loaded
|
|
||||
// console.log("--------------------");
|
|
||||
// console.log("drawImage " + img.src);
|
|
||||
try { |
|
||||
// console.log("try...");
|
|
||||
draw(); |
|
||||
} catch(error) { |
|
||||
// console.log("catch: " + error);
|
|
||||
img.onload = dodraw; |
|
||||
} |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
// Draw polygon
|
|
||||
$.fn.drawPolygon = function(args) { |
|
||||
var ctx = this.loadCanvas(), |
|
||||
params = $.extend({}, jC.defaults, args), |
|
||||
theta, dtheta, x, y, |
|
||||
toRad = checkUnits(params), i; |
|
||||
setGlobals(ctx, params); |
|
||||
|
|
||||
if (params.sides >= 3) { |
|
||||
// Calculate points and draw
|
|
||||
theta = (Math.PI/2) + (Math.PI/params.sides) + (params.angle*toRad); |
|
||||
dtheta = (Math.PI*2) / params.sides; |
|
||||
for (i=0; i<params.sides; i+=1) { |
|
||||
x = params.x + (params.radius * Math.cos(theta)) + 1e-10; |
|
||||
y = params.y + (params.radius * Math.sin(theta)) + 1e-10; |
|
||||
if (params.fromCenter === false) { |
|
||||
x += params.radius; |
|
||||
y += params.radius; |
|
||||
} |
|
||||
ctx.lineTo(x, y); |
|
||||
theta += dtheta; |
|
||||
} |
|
||||
closePath(ctx, params); |
|
||||
} |
|
||||
return this; |
|
||||
}; |
|
||||
|
|
||||
return window.jCanvas = jC; |
|
||||
}(jQuery, document, Math, Number)); |
|
||||
File diff suppressed because one or more lines are too long
@ -1,220 +0,0 @@ |
|||||
/*! |
|
||||
* jQuery "stepper" Plugin |
|
||||
* version 0.0.1 |
|
||||
* @requires jQuery v1.3.2 or later |
|
||||
* @requires jCanvas |
|
||||
* |
|
||||
* Authored 2011-06-11 Scott Lahteine (thinkyhead.com) |
|
||||
* |
|
||||
* A very simple numerical stepper. |
|
||||
* TODO: place arrows based on div size, make 50/50 width |
|
||||
* |
|
||||
* Usage example: |
|
||||
* |
|
||||
* $('#mydiv').jstepper({ |
|
||||
* min: 1, |
|
||||
* max: 4, |
|
||||
* val: 1, |
|
||||
* arrowWidth: 15, |
|
||||
* arrowHeight: '22px', |
|
||||
* color: '#FFF', |
|
||||
* acolor: '#F70', |
|
||||
* hcolor: '#FF0', |
|
||||
* id: 'select-me', |
|
||||
* stepperClass: 'inner', |
|
||||
* textStyle: {width:'1.5em',fontSize:'20px',textAlign:'center'}, |
|
||||
* onChange: function(v) { }, |
|
||||
* }); |
|
||||
* |
|
||||
*/ |
|
||||
;(function($) { |
|
||||
var un = 'undefined'; |
|
||||
|
|
||||
$.jstepperArrows = [ |
|
||||
{ name:'prev', poly:[[1.0,0],[0,0.5],[1.0,1.0]] }, |
|
||||
{ name:'next', poly:[[0,0],[1.0,0.5],[0,1.0]] } |
|
||||
]; |
|
||||
|
|
||||
$.fn.jstepper = function(args) { |
|
||||
|
|
||||
return this.each(function() { |
|
||||
|
|
||||
var defaults = { |
|
||||
min: 1, |
|
||||
max: null, |
|
||||
val: null, |
|
||||
active: true, |
|
||||
placeholder: null, |
|
||||
arrowWidth: 0, |
|
||||
arrowHeight: 0, |
|
||||
color: '#FFF', |
|
||||
hcolor: '#FF0', |
|
||||
acolor: '#F80', |
|
||||
id: '', |
|
||||
stepperClass: '', |
|
||||
textStyle: '', |
|
||||
onChange: (function(v){ if (typeof console.log !== 'undefined') console.log("val="+v); }) |
|
||||
}; |
|
||||
|
|
||||
args = $.extend(defaults, args || {}); |
|
||||
|
|
||||
var min = args.min * 1, |
|
||||
max = (args.max !== null) ? args.max * 1 : min, |
|
||||
span = max - min + 1, |
|
||||
val = (args.val !== null) ? args.val * 1 : min, |
|
||||
active = !args.disabled, |
|
||||
placeholder = args.placeholder, |
|
||||
arrowWidth = 1 * args.arrowWidth.toString().replace(/px/,''), |
|
||||
arrowHeight = 1 * args.arrowHeight.toString().replace(/px/,''), |
|
||||
color = args.color, |
|
||||
hcolor = args.hcolor, |
|
||||
acolor = args.acolor, |
|
||||
$prev = $('<a href="#prev" style="cursor:w-resize;"><canvas/></a>'), |
|
||||
$marq = $('<div class="number"/>').css({float:'left',textAlign:'center'}), |
|
||||
$next = $('<a href="#next" style="cursor:e-resize;"><canvas/></a>'), |
|
||||
arrow = [ $prev.find('canvas')[0], $next.find('canvas')[0] ], |
|
||||
$stepper = $('<span class="jstepper"/>').append($prev).append($marq).append($next).append('<div style="clear:both;"/>'), |
|
||||
onChange = args.onChange; |
|
||||
|
|
||||
if (args.id) $stepper[0].id = args.id; |
|
||||
if (args.stepperClass) $stepper.addClass(args.stepperClass); |
|
||||
if (args.textStyle) $marq.css(args.textStyle); |
|
||||
|
|
||||
// replace a span, but embed elsewhere
|
|
||||
if (this.tagName == 'SPAN') { |
|
||||
var previd = this.id; |
|
||||
$(this).replaceWith($stepper); |
|
||||
if (previd) $stepper.attr('id',previd); |
|
||||
} |
|
||||
else { |
|
||||
$(this).append($stepper); |
|
||||
} |
|
||||
|
|
||||
// hook to call functions on this object
|
|
||||
$stepper[0].ui = { |
|
||||
|
|
||||
refresh: function() { |
|
||||
this.updateNumber(); |
|
||||
this._drawArrow(0, 1); |
|
||||
this._drawArrow(1, 1); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
_drawArrow: function(i,state) { |
|
||||
var $elm = $(arrow[i]), |
|
||||
desc = $.jstepperArrows[i], |
|
||||
fillStyle = (state == 2) ? hcolor : (state == 3) ? acolor : color, |
|
||||
draw = { fillStyle: fillStyle }, |
|
||||
w = $elm.width(), h = $elm.height(); |
|
||||
|
|
||||
if (w <= 0) w = $elm.attr('width'); |
|
||||
if (h <= 0) h = $elm.attr('height'); |
|
||||
|
|
||||
$.each(desc.poly,function(i,v){ |
|
||||
++i; |
|
||||
draw['x'+i] = v[0] * w; |
|
||||
draw['y'+i] = v[1] * h; |
|
||||
}); |
|
||||
$elm.restoreCanvas().clearCanvas().drawLine(draw); |
|
||||
}, |
|
||||
|
|
||||
updateNumber: function() { |
|
||||
$marq.html((active || placeholder === null) ? val.toString() : placeholder); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
_doclick: function(i) { |
|
||||
this.add(i ? 1 : -1); |
|
||||
this._drawArrow(i, 3); |
|
||||
var self = this; |
|
||||
setTimeout(function(){ self._drawArrow(i, 2); }, 50); |
|
||||
}, |
|
||||
|
|
||||
add: function(x) { |
|
||||
val = (((val - min) + x + span) % span) + min; |
|
||||
this.updateNumber(); |
|
||||
this.didChange(val); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
min: function(v) { |
|
||||
if (typeof v === un) return min; |
|
||||
this.setRange(v,max); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
max: function(v) { |
|
||||
if (typeof v === un) return max; |
|
||||
this.setRange(min,v); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
val: function(v) { |
|
||||
if (typeof v === un) return val; |
|
||||
val = (((v - min) + span) % span) + min; |
|
||||
this.updateNumber(); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
setRange: function(lo, hi, ini) { |
|
||||
if (lo > hi) hi = (lo += hi -= lo) - hi; |
|
||||
min = lo; max = hi; span = hi - lo + 1; |
|
||||
if (typeof ini !== un) val = ini; |
|
||||
if (val < min) val = min; |
|
||||
if (val > max) val = max; |
|
||||
this.updateNumber(); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
active: function(a) { |
|
||||
if (typeof a === un) return active; |
|
||||
(active = a) ? $marq.removeClass('inactive') : $marq.addClass('inactive'); |
|
||||
this.updateNumber(); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
disable: function() { this.active(false); return this; }, |
|
||||
enable: function() { this.active(true); return this; }, |
|
||||
|
|
||||
clearPlaceholder: function() { |
|
||||
this.setPlaceholder(null); |
|
||||
return this; |
|
||||
}, |
|
||||
setPlaceholder: function(p) { |
|
||||
placeholder = p; |
|
||||
if (!active) this.updateNumber(); |
|
||||
return this; |
|
||||
}, |
|
||||
|
|
||||
didChange: onChange |
|
||||
|
|
||||
}; |
|
||||
|
|
||||
// set hover and click for each arrow
|
|
||||
$.each($.jstepperArrows, function(i,desc) { |
|
||||
var $elm = $(arrow[i]), |
|
||||
w = arrowWidth ? arrowWidth : $elm.width() ? $elm.width() : 15, |
|
||||
h = arrowHeight ? arrowHeight : $elm.height() ? $elm.height() : 24; |
|
||||
$elm[0]._index = i; |
|
||||
$elm |
|
||||
.css({float:'left'}) |
|
||||
.attr({width:w,height:h,'class':desc.name}) |
|
||||
.hover( |
|
||||
function(e) { $stepper[0].ui._drawArrow(e.target._index, 2); }, |
|
||||
function(e) { $stepper[0].ui._drawArrow(e.target._index, 1); } |
|
||||
) |
|
||||
.click(function(e){ |
|
||||
$stepper[0].ui._doclick(e.target._index); |
|
||||
return false; |
|
||||
}); |
|
||||
}); |
|
||||
|
|
||||
// init the visuals first time
|
|
||||
$stepper[0].ui.refresh(); |
|
||||
|
|
||||
}); // this.each
|
|
||||
|
|
||||
}; // $.fn.jstepper
|
|
||||
|
|
||||
})( jQuery ); |
|
||||
|
|
||||
File diff suppressed because one or more lines are too long
@ -0,0 +1,115 @@ |
|||||
|
/*
|
||||
|
|
||||
|
mcp4728.cpp - Arduino library for MicroChip MCP4728 I2C D/A converter |
||||
|
For implementation details, please take a look at the datasheet http://ww1.microchip.com/downloads/en/DeviceDoc/22187a.pdf
|
||||
|
For discussion and feedback, please go to http://arduino.cc/forum/index.php/topic,51842.0.html
|
||||
|
*/ |
||||
|
|
||||
|
|
||||
|
/* _____PROJECT INCLUDES_____________________________________________________ */ |
||||
|
#include "dac_mcp4728.h" |
||||
|
|
||||
|
#if ENABLED(DAC_STEPPER_CURRENT) |
||||
|
|
||||
|
// Used Global variables
|
||||
|
uint16_t mcp4728_values[4]; |
||||
|
|
||||
|
/*
|
||||
|
Begin I2C, get current values (input register and eeprom) of mcp4728 |
||||
|
*/ |
||||
|
void mcp4728_init() { |
||||
|
Wire.begin(); |
||||
|
Wire.requestFrom(int(DAC_DEV_ADDRESS), 24); |
||||
|
while(Wire.available()) { |
||||
|
int deviceID = Wire.receive(); |
||||
|
int hiByte = Wire.receive(); |
||||
|
int loByte = Wire.receive(); |
||||
|
|
||||
|
int isEEPROM = (deviceID & 0B00001000) >> 3; |
||||
|
int channel = (deviceID & 0B00110000) >> 4; |
||||
|
if (isEEPROM != 1) { |
||||
|
mcp4728_values[channel] = word((hiByte & 0B00001111), loByte); |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
|
||||
|
/*
|
||||
|
Write input resister value to specified channel using fastwrite method. |
||||
|
Channel : 0-3, Values : 0-4095 |
||||
|
*/ |
||||
|
uint8_t mcp4728_analogWrite(uint8_t channel, uint16_t value) { |
||||
|
mcp4728_values[channel] = value; |
||||
|
return mcp4728_fastWrite(); |
||||
|
} |
||||
|
/*
|
||||
|
Write all input resistor values to EEPROM using SequencialWrite method. |
||||
|
This will update both input register and EEPROM value |
||||
|
This will also write current Vref, PowerDown, Gain settings to EEPROM |
||||
|
*/ |
||||
|
uint8_t mcp4728_eepromWrite() { |
||||
|
Wire.beginTransmission(DAC_DEV_ADDRESS); |
||||
|
Wire.send(SEQWRITE); |
||||
|
for (uint8_t channel=0; channel <= 3; channel++) { |
||||
|
Wire.send(DAC_STEPPER_VREF << 7 | 0 << 5 | DAC_STEPPER_GAIN << 4 | highByte(mcp4728_values[channel])); |
||||
|
Wire.send(lowByte(mcp4728_values[channel])); |
||||
|
} |
||||
|
return Wire.endTransmission(); |
||||
|
} |
||||
|
|
||||
|
/*
|
||||
|
Write Voltage reference setting to all input regiters |
||||
|
*/ |
||||
|
uint8_t mcp4728_setVref_all(uint8_t value) { |
||||
|
Wire.beginTransmission(DAC_DEV_ADDRESS); |
||||
|
Wire.send(VREFWRITE | value << 3 | value << 2 | value << 1 | value); |
||||
|
return Wire.endTransmission(); |
||||
|
} |
||||
|
/*
|
||||
|
Write Gain setting to all input regiters |
||||
|
*/ |
||||
|
uint8_t mcp4728_setGain_all(uint8_t value) { |
||||
|
Wire.beginTransmission(DAC_DEV_ADDRESS); |
||||
|
Wire.send(GAINWRITE | value << 3 | value << 2 | value << 1 | value); |
||||
|
return Wire.endTransmission(); |
||||
|
} |
||||
|
|
||||
|
/*
|
||||
|
Return Input Regiter value |
||||
|
*/ |
||||
|
uint16_t mcp4728_getValue(uint8_t channel) { return mcp4728_values[channel]; } |
||||
|
|
||||
|
/*
|
||||
|
// Steph: Might be useful in the future
|
||||
|
// Return Vout
|
||||
|
uint16_t mcp4728_getVout(uint8_t channel) { |
||||
|
uint32_t vref = 2048; |
||||
|
uint32_t vOut = (vref * mcp4728_values[channel] * (_DAC_STEPPER_GAIN + 1)) / 4096; |
||||
|
if (vOut > defaultVDD) vOut = defaultVDD; |
||||
|
return vOut; |
||||
|
} |
||||
|
*/ |
||||
|
|
||||
|
/*
|
||||
|
FastWrite input register values - All DAC ouput update. refer to DATASHEET 5.6.1 |
||||
|
DAC Input and PowerDown bits update. |
||||
|
No EEPROM update |
||||
|
*/ |
||||
|
uint8_t mcp4728_fastWrite() { |
||||
|
Wire.beginTransmission(DAC_DEV_ADDRESS); |
||||
|
for (uint8_t channel=0; channel <= 3; channel++) { |
||||
|
Wire.send(highByte(mcp4728_values[channel])); |
||||
|
Wire.send(lowByte(mcp4728_values[channel])); |
||||
|
} |
||||
|
return Wire.endTransmission(); |
||||
|
} |
||||
|
|
||||
|
/*
|
||||
|
Common function for simple general commands |
||||
|
*/ |
||||
|
uint8_t mcp4728_simpleCommand(byte simpleCommand) { |
||||
|
Wire.beginTransmission(GENERALCALL); |
||||
|
Wire.send(simpleCommand); |
||||
|
return Wire.endTransmission(); |
||||
|
} |
||||
|
|
||||
|
#endif // DAC_STEPPER_CURRENT
|
||||
@ -0,0 +1,44 @@ |
|||||
|
/**
|
||||
|
Arduino library for MicroChip MCP4728 I2C D/A converter. |
||||
|
*/ |
||||
|
|
||||
|
#ifndef mcp4728_h |
||||
|
#define mcp4728_h |
||||
|
|
||||
|
#include "Configuration.h" |
||||
|
#include "Configuration_adv.h" |
||||
|
|
||||
|
#if ENABLED(DAC_STEPPER_CURRENT) |
||||
|
#include "WProgram.h" |
||||
|
#include "Wire.h" |
||||
|
//#include <Wire.h>
|
||||
|
|
||||
|
#define defaultVDD 5000 |
||||
|
#define BASE_ADDR 0x60 |
||||
|
#define RESET 0B00000110 |
||||
|
#define WAKE 0B00001001 |
||||
|
#define UPDATE 0B00001000 |
||||
|
#define MULTIWRITE 0B01000000 |
||||
|
#define SINGLEWRITE 0B01011000 |
||||
|
#define SEQWRITE 0B01010000 |
||||
|
#define VREFWRITE 0B10000000 |
||||
|
#define GAINWRITE 0B11000000 |
||||
|
#define POWERDOWNWRITE 0B10100000 |
||||
|
#define GENERALCALL 0B0000000 |
||||
|
#define GAINWRITE 0B11000000 |
||||
|
|
||||
|
// This is taken from the original lib, makes it easy to edit if needed
|
||||
|
#define DAC_DEV_ADDRESS (BASE_ADDR | 0x00) |
||||
|
|
||||
|
void mcp4728_init(); |
||||
|
uint8_t mcp4728_analogWrite(uint8_t channel, uint16_t value); |
||||
|
uint8_t mcp4728_eepromWrite(); |
||||
|
uint8_t mcp4728_setVref_all(uint8_t value); |
||||
|
uint8_t mcp4728_setGain_all(uint8_t value); |
||||
|
uint16_t mcp4728_getValue(uint8_t channel); |
||||
|
uint8_t mcp4728_fastWrite(); |
||||
|
uint8_t mcp4728_simpleCommand(byte simpleCommand); |
||||
|
|
||||
|
#endif |
||||
|
#endif |
||||
|
|
||||
@ -0,0 +1,630 @@ |
|||||
|
#ifndef CONFIGURATION_ADV_H |
||||
|
#define CONFIGURATION_ADV_H |
||||
|
|
||||
|
#include "Conditionals.h" |
||||
|
|
||||
|
// @section temperature
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//=============================Thermal Settings ============================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
#if ENABLED(BED_LIMIT_SWITCHING) |
||||
|
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
|
#endif |
||||
|
#define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
|
||||
|
|
||||
|
/**
|
||||
|
* Thermal Protection parameters |
||||
|
*/ |
||||
|
/**
|
||||
|
* Thermal Protection protects your printer from damage and fire if a |
||||
|
* thermistor falls out or temperature sensors fail in any way. |
||||
|
* |
||||
|
* The issue: If a thermistor falls out or a temperature sensor fails, |
||||
|
* Marlin can no longer sense the actual temperature. Since a disconnected |
||||
|
* thermistor reads as a low temperature, the firmware will keep the heater on. |
||||
|
* |
||||
|
* The solution: Once the temperature reaches the target, start observing. |
||||
|
* If the temperature stays too far below the target (hysteresis) for too long (period), |
||||
|
* the firmware will halt the machine as a safety precaution. |
||||
|
* |
||||
|
* If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD |
||||
|
*/ |
||||
|
#if ENABLED(THERMAL_PROTECTION_HOTENDS) |
||||
|
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
|
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
|
|
||||
|
/**
|
||||
|
* Whenever an M104 or M109 increases the target temperature the firmware will wait for the |
||||
|
* WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE |
||||
|
* degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109, |
||||
|
* but only if the current temperature is far enough below the target for a reliable test. |
||||
|
* |
||||
|
* If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE |
||||
|
* WATCH_TEMP_INCREASE should not be below 2. |
||||
|
*/ |
||||
|
#define WATCH_TEMP_PERIOD 16 // Seconds
|
||||
|
#define WATCH_TEMP_INCREASE 4 // Degrees Celsius
|
||||
|
#endif |
||||
|
|
||||
|
/**
|
||||
|
* Thermal Protection parameters for the bed |
||||
|
* are like the above for the hotends. |
||||
|
* WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. |
||||
|
*/ |
||||
|
#if ENABLED(THERMAL_PROTECTION_BED) |
||||
|
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
|
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
#endif |
||||
|
|
||||
|
#if ENABLED(PIDTEMP) |
||||
|
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
|
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
|
#define PID_ADD_EXTRUSION_RATE |
||||
|
#if ENABLED(PID_ADD_EXTRUSION_RATE) |
||||
|
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
|
||||
|
#define LPQ_MAX_LEN 50 |
||||
|
#endif |
||||
|
#endif |
||||
|
|
||||
|
/**
|
||||
|
* Automatic Temperature: |
||||
|
* The hotend target temperature is calculated by all the buffered lines of gcode. |
||||
|
* The maximum buffered steps/sec of the extruder motor is called "se". |
||||
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor> |
||||
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by |
||||
|
* mintemp and maxtemp. Turn this off by executing M109 without F* |
||||
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. |
||||
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode |
||||
|
*/ |
||||
|
#define AUTOTEMP |
||||
|
#if ENABLED(AUTOTEMP) |
||||
|
#define AUTOTEMP_OLDWEIGHT 0.98 |
||||
|
#endif |
||||
|
|
||||
|
//Show Temperature ADC value
|
||||
|
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
|
||||
|
//#define SHOW_TEMP_ADC_VALUES
|
||||
|
|
||||
|
// @section extruder
|
||||
|
|
||||
|
// extruder run-out prevention.
|
||||
|
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
|
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
|
#define EXTRUDER_RUNOUT_MINTEMP 190 |
||||
|
#define EXTRUDER_RUNOUT_SECONDS 30. |
||||
|
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
|
||||
|
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
|
||||
|
#define EXTRUDER_RUNOUT_EXTRUDE 100 |
||||
|
|
||||
|
// @section temperature
|
||||
|
|
||||
|
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
|
||||
|
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
|
||||
|
#define TEMP_SENSOR_AD595_OFFSET 0.0 |
||||
|
#define TEMP_SENSOR_AD595_GAIN 1.0 |
||||
|
|
||||
|
//This is for controlling a fan to cool down the stepper drivers
|
||||
|
//it will turn on when any driver is enabled
|
||||
|
//and turn off after the set amount of seconds from last driver being disabled again
|
||||
|
#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable)
|
||||
|
#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
|
||||
|
#define CONTROLLERFAN_SPEED 255 // == full speed
|
||||
|
|
||||
|
// When first starting the main fan, run it at full speed for the
|
||||
|
// given number of milliseconds. This gets the fan spinning reliably
|
||||
|
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
|
//#define FAN_KICKSTART_TIME 100
|
||||
|
|
||||
|
// This defines the minimal speed for the main fan, run in PWM mode
|
||||
|
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
|
||||
|
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
|
||||
|
//#define FAN_MIN_PWM 50
|
||||
|
|
||||
|
// @section extruder
|
||||
|
|
||||
|
// Extruder cooling fans
|
||||
|
// Configure fan pin outputs to automatically turn on/off when the associated
|
||||
|
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
|
// Multiple extruders can be assigned to the same pin in which case
|
||||
|
// the fan will turn on when any selected extruder is above the threshold.
|
||||
|
#define EXTRUDER_0_AUTO_FAN_PIN 11 |
||||
|
#define EXTRUDER_1_AUTO_FAN_PIN 6 |
||||
|
#define EXTRUDER_2_AUTO_FAN_PIN -1 |
||||
|
#define EXTRUDER_3_AUTO_FAN_PIN -1 |
||||
|
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 |
||||
|
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
|
||||
|
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//=============================Mechanical Settings===========================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
// @section homing
|
||||
|
|
||||
|
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
|
||||
|
// @section extras
|
||||
|
|
||||
|
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
|
||||
|
// A single Z stepper driver is usually used to drive 2 stepper motors.
|
||||
|
// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
|
||||
|
// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
|
||||
|
// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
|
||||
|
// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
|
||||
|
//#define Z_DUAL_STEPPER_DRIVERS
|
||||
|
|
||||
|
#if ENABLED(Z_DUAL_STEPPER_DRIVERS) |
||||
|
|
||||
|
// Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
|
||||
|
// That way the machine is capable to align the bed during home, since both Z steppers are homed.
|
||||
|
// There is also an implementation of M666 (software endstops adjustment) to this feature.
|
||||
|
// After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
|
||||
|
// One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
|
||||
|
// If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
|
||||
|
// Play a little bit with small adjustments (0.5mm) and check the behaviour.
|
||||
|
// The M119 (endstops report) will start reporting the Z2 Endstop as well.
|
||||
|
|
||||
|
//#define Z_DUAL_ENDSTOPS
|
||||
|
|
||||
|
#if ENABLED(Z_DUAL_ENDSTOPS) |
||||
|
#define Z2_MAX_PIN 36 //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
|
||||
|
const bool Z2_MAX_ENDSTOP_INVERTING = false; |
||||
|
#define DISABLE_XMAX_ENDSTOP //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
|
||||
|
#endif |
||||
|
|
||||
|
#endif // Z_DUAL_STEPPER_DRIVERS
|
||||
|
|
||||
|
// Same again but for Y Axis.
|
||||
|
//#define Y_DUAL_STEPPER_DRIVERS
|
||||
|
|
||||
|
#if ENABLED(Y_DUAL_STEPPER_DRIVERS) |
||||
|
// Define if the two Y drives need to rotate in opposite directions
|
||||
|
#define INVERT_Y2_VS_Y_DIR true |
||||
|
#endif |
||||
|
|
||||
|
// Enable this for dual x-carriage printers.
|
||||
|
// A dual x-carriage design has the advantage that the inactive extruder can be parked which
|
||||
|
// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
|
||||
|
// allowing faster printing speeds.
|
||||
|
//#define DUAL_X_CARRIAGE
|
||||
|
#if ENABLED(DUAL_X_CARRIAGE) |
||||
|
// Configuration for second X-carriage
|
||||
|
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
|
// the second x-carriage always homes to the maximum endstop.
|
||||
|
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
|
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
|
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
|
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
|
// However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
|
||||
|
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
|
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
|
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
|
|
||||
|
// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
|
||||
|
#define X2_ENABLE_PIN 29 |
||||
|
#define X2_STEP_PIN 25 |
||||
|
#define X2_DIR_PIN 23 |
||||
|
|
||||
|
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
|
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
|
// as long as it supports dual x-carriages. (M605 S0)
|
||||
|
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
|
// that additional slicer support is not required. (M605 S1)
|
||||
|
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
|
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
|
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
|
|
||||
|
// This is the default power-up mode which can be later using M605.
|
||||
|
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0 |
||||
|
|
||||
|
// Default settings in "Auto-park Mode"
|
||||
|
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
|
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
|
|
||||
|
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
|
#define DEFAULT_DUPLICATION_X_OFFSET 100 |
||||
|
|
||||
|
#endif //DUAL_X_CARRIAGE
|
||||
|
|
||||
|
// @section homing
|
||||
|
|
||||
|
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
|
#define X_HOME_BUMP_MM 5 |
||||
|
#define Y_HOME_BUMP_MM 5 |
||||
|
#define Z_HOME_BUMP_MM 2 |
||||
|
#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
|
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
|
||||
|
// When G28 is called, this option will make Y home before X
|
||||
|
//#define HOME_Y_BEFORE_X
|
||||
|
|
||||
|
// @section machine
|
||||
|
|
||||
|
#define AXIS_RELATIVE_MODES {false, false, false, false} |
||||
|
|
||||
|
// @section machine
|
||||
|
|
||||
|
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
|
#define INVERT_X_STEP_PIN false |
||||
|
#define INVERT_Y_STEP_PIN false |
||||
|
#define INVERT_Z_STEP_PIN false |
||||
|
#define INVERT_E_STEP_PIN false |
||||
|
|
||||
|
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
|
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
|
||||
|
// Time can be set by M18 and M84.
|
||||
|
#define DEFAULT_STEPPER_DEACTIVE_TIME 60 |
||||
|
#define DISABLE_INACTIVE_X true |
||||
|
#define DISABLE_INACTIVE_Y true |
||||
|
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
|
||||
|
#define DISABLE_INACTIVE_E true |
||||
|
|
||||
|
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
|
#define DEFAULT_MINTRAVELFEEDRATE 0.0 |
||||
|
|
||||
|
// @section lcd
|
||||
|
|
||||
|
#if ENABLED(ULTIPANEL) |
||||
|
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
|
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
|
#endif |
||||
|
|
||||
|
// @section extras
|
||||
|
|
||||
|
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
#define DEFAULT_MINSEGMENTTIME 20000 |
||||
|
|
||||
|
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
|
#define SLOWDOWN |
||||
|
|
||||
|
// Frequency limit
|
||||
|
// See nophead's blog for more info
|
||||
|
// Not working O
|
||||
|
//#define XY_FREQUENCY_LIMIT 15
|
||||
|
|
||||
|
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
||||
|
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
||||
|
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
||||
|
#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
|
||||
|
|
||||
|
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
|
||||
|
#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
|
||||
|
|
||||
|
// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
|
||||
|
#define DIGIPOT_MOTOR_CURRENT {150, 170, 180, 190, 180} // Values 0-255 (bq ZUM Mega 3D (default): X = 150 [~1.17A]; Y = 170 [~1.33A]; Z = 180 [~1.41A]; E0 = 190 [~1.49A])
|
||||
|
|
||||
|
// Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current)
|
||||
|
//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
|
||||
|
|
||||
|
// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
|
||||
|
//#define DIGIPOT_I2C
|
||||
|
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
|
||||
|
#define DIGIPOT_I2C_NUM_CHANNELS 8 |
||||
|
// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
|
||||
|
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} |
||||
|
|
||||
|
//===========================================================================
|
||||
|
//=============================Additional Features===========================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
|
||||
|
#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
|
||||
|
#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
|
||||
|
|
||||
|
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
|
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
|
||||
|
// @section lcd
|
||||
|
|
||||
|
#if ENABLED(SDSUPPORT) |
||||
|
|
||||
|
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
|
||||
|
// around this by connecting a push button or single throw switch to the pin defined
|
||||
|
// as SD_DETECT_PIN in your board's pins definitions.
|
||||
|
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
|
||||
|
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
|
||||
|
#define SD_DETECT_INVERTED |
||||
|
|
||||
|
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
|
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
|
|
||||
|
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
|
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
|
// using:
|
||||
|
#define MENU_ADDAUTOSTART |
||||
|
|
||||
|
// Show a progress bar on HD44780 LCDs for SD printing
|
||||
|
//#define LCD_PROGRESS_BAR
|
||||
|
|
||||
|
#if ENABLED(LCD_PROGRESS_BAR) |
||||
|
// Amount of time (ms) to show the bar
|
||||
|
#define PROGRESS_BAR_BAR_TIME 2000 |
||||
|
// Amount of time (ms) to show the status message
|
||||
|
#define PROGRESS_BAR_MSG_TIME 3000 |
||||
|
// Amount of time (ms) to retain the status message (0=forever)
|
||||
|
#define PROGRESS_MSG_EXPIRE 0 |
||||
|
// Enable this to show messages for MSG_TIME then hide them
|
||||
|
//#define PROGRESS_MSG_ONCE
|
||||
|
#endif |
||||
|
|
||||
|
// This allows hosts to request long names for files and folders with M33
|
||||
|
#define LONG_FILENAME_HOST_SUPPORT |
||||
|
|
||||
|
// This option allows you to abort SD printing when any endstop is triggered.
|
||||
|
// This feature must be enabled with "M540 S1" or from the LCD menu.
|
||||
|
// To have any effect, endstops must be enabled during SD printing.
|
||||
|
// With ENDSTOPS_ONLY_FOR_HOMING you must send "M120" to enable endstops.
|
||||
|
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
||||
|
|
||||
|
#endif // SDSUPPORT
|
||||
|
|
||||
|
// for dogm lcd displays you can choose some additional fonts:
|
||||
|
#if ENABLED(DOGLCD) |
||||
|
// save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
|
||||
|
// we don't have a big font for Cyrillic, Kana
|
||||
|
//#define USE_BIG_EDIT_FONT
|
||||
|
|
||||
|
// If you have spare 2300Byte of progmem and want to use a
|
||||
|
// smaller font on the Info-screen uncomment the next line.
|
||||
|
#define USE_SMALL_INFOFONT |
||||
|
#endif // DOGLCD
|
||||
|
|
||||
|
// @section more
|
||||
|
|
||||
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
|
#define USE_WATCHDOG |
||||
|
|
||||
|
#if ENABLED(USE_WATCHDOG) |
||||
|
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
|
||||
|
// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
|
||||
|
// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
|
||||
|
//#define WATCHDOG_RESET_MANUAL
|
||||
|
#endif |
||||
|
|
||||
|
// @section lcd
|
||||
|
|
||||
|
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
|
||||
|
// it can e.g. be used to change z-positions in the print startup phase in real-time
|
||||
|
// does not respect endstops!
|
||||
|
//#define BABYSTEPPING
|
||||
|
#if ENABLED(BABYSTEPPING) |
||||
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||
|
//not implemented for deltabots!
|
||||
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||
|
#endif |
||||
|
|
||||
|
// @section extruder
|
||||
|
|
||||
|
// extruder advance constant (s2/mm3)
|
||||
|
//
|
||||
|
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
|
//
|
||||
|
// Hooke's law says: force = k * distance
|
||||
|
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
|
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
|
//#define ADVANCE
|
||||
|
|
||||
|
#if ENABLED(ADVANCE) |
||||
|
#define EXTRUDER_ADVANCE_K .0 |
||||
|
#define D_FILAMENT 2.85 |
||||
|
#endif |
||||
|
|
||||
|
// @section extras
|
||||
|
|
||||
|
// Arc interpretation settings:
|
||||
|
#define MM_PER_ARC_SEGMENT 1 |
||||
|
#define N_ARC_CORRECTION 25 |
||||
|
|
||||
|
const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
|
||||
|
// @section temperature
|
||||
|
|
||||
|
// Control heater 0 and heater 1 in parallel.
|
||||
|
//#define HEATERS_PARALLEL
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//================================= Buffers =================================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
// @section hidden
|
||||
|
|
||||
|
// The number of linear motions that can be in the plan at any give time.
|
||||
|
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
|
#if ENABLED(SDSUPPORT) |
||||
|
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
|
#else |
||||
|
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
|
#endif |
||||
|
|
||||
|
// @section more
|
||||
|
|
||||
|
//The ASCII buffer for receiving from the serial:
|
||||
|
#define MAX_CMD_SIZE 96 |
||||
|
#define BUFSIZE 4 |
||||
|
|
||||
|
// Bad Serial-connections can miss a received command by sending an 'ok'
|
||||
|
// Therefore some clients abort after 30 seconds in a timeout.
|
||||
|
// Some other clients start sending commands while receiving a 'wait'.
|
||||
|
// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
|
||||
|
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
|
||||
|
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
|
//#define ADVANCED_OK
|
||||
|
|
||||
|
// @section fwretract
|
||||
|
|
||||
|
// Firmware based and LCD controlled retract
|
||||
|
// M207 and M208 can be used to define parameters for the retraction.
|
||||
|
// The retraction can be called by the slicer using G10 and G11
|
||||
|
// until then, intended retractions can be detected by moves that only extrude and the direction.
|
||||
|
// the moves are than replaced by the firmware controlled ones.
|
||||
|
|
||||
|
//#define FWRETRACT //ONLY PARTIALLY TESTED
|
||||
|
#if ENABLED(FWRETRACT) |
||||
|
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
|
||||
|
#define RETRACT_LENGTH 3 //default retract length (positive mm)
|
||||
|
#define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
|
||||
|
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
|
||||
|
#define RETRACT_ZLIFT 0 //default retract Z-lift
|
||||
|
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
|
||||
|
#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
|
||||
|
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
|
#endif |
||||
|
|
||||
|
// Add support for experimental filament exchange support M600; requires display
|
||||
|
#if ENABLED(ULTIPANEL) |
||||
|
//#define FILAMENTCHANGEENABLE
|
||||
|
#if ENABLED(FILAMENTCHANGEENABLE) |
||||
|
#define FILAMENTCHANGE_XPOS 3 |
||||
|
#define FILAMENTCHANGE_YPOS 3 |
||||
|
#define FILAMENTCHANGE_ZADD 10 |
||||
|
#define FILAMENTCHANGE_FIRSTRETRACT -2 |
||||
|
#define FILAMENTCHANGE_FINALRETRACT -100 |
||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||
|
#endif |
||||
|
#endif |
||||
|
|
||||
|
/******************************************************************************\
|
||||
|
* enable this section if you have TMC26X motor drivers. |
||||
|
* you need to import the TMC26XStepper library into the Arduino IDE for this |
||||
|
******************************************************************************/ |
||||
|
|
||||
|
// @section tmc
|
||||
|
|
||||
|
//#define HAVE_TMCDRIVER
|
||||
|
#if ENABLED(HAVE_TMCDRIVER) |
||||
|
|
||||
|
//#define X_IS_TMC
|
||||
|
#define X_MAX_CURRENT 1000 //in mA
|
||||
|
#define X_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define X2_IS_TMC
|
||||
|
#define X2_MAX_CURRENT 1000 //in mA
|
||||
|
#define X2_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define Y_IS_TMC
|
||||
|
#define Y_MAX_CURRENT 1000 //in mA
|
||||
|
#define Y_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define Y2_IS_TMC
|
||||
|
#define Y2_MAX_CURRENT 1000 //in mA
|
||||
|
#define Y2_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define Z_IS_TMC
|
||||
|
#define Z_MAX_CURRENT 1000 //in mA
|
||||
|
#define Z_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define Z2_IS_TMC
|
||||
|
#define Z2_MAX_CURRENT 1000 //in mA
|
||||
|
#define Z2_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define E0_IS_TMC
|
||||
|
#define E0_MAX_CURRENT 1000 //in mA
|
||||
|
#define E0_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define E1_IS_TMC
|
||||
|
#define E1_MAX_CURRENT 1000 //in mA
|
||||
|
#define E1_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define E2_IS_TMC
|
||||
|
#define E2_MAX_CURRENT 1000 //in mA
|
||||
|
#define E2_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
//#define E3_IS_TMC
|
||||
|
#define E3_MAX_CURRENT 1000 //in mA
|
||||
|
#define E3_SENSE_RESISTOR 91 //in mOhms
|
||||
|
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
|
|
||||
|
#endif |
||||
|
|
||||
|
/******************************************************************************\
|
||||
|
* enable this section if you have L6470 motor drivers. |
||||
|
* you need to import the L6470 library into the Arduino IDE for this |
||||
|
******************************************************************************/ |
||||
|
|
||||
|
// @section l6470
|
||||
|
|
||||
|
//#define HAVE_L6470DRIVER
|
||||
|
#if ENABLED(HAVE_L6470DRIVER) |
||||
|
|
||||
|
//#define X_IS_L6470
|
||||
|
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define X2_IS_L6470
|
||||
|
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define Y_IS_L6470
|
||||
|
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define Y2_IS_L6470
|
||||
|
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define Z_IS_L6470
|
||||
|
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define Z2_IS_L6470
|
||||
|
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define E0_IS_L6470
|
||||
|
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define E1_IS_L6470
|
||||
|
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define E2_IS_L6470
|
||||
|
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
//#define E3_IS_L6470
|
||||
|
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
|
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
|
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
|
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
|
||||
|
#endif |
||||
|
|
||||
|
#include "Conditionals.h" |
||||
|
#include "SanityCheck.h" |
||||
|
|
||||
|
#endif //CONFIGURATION_ADV_H
|
||||
@ -0,0 +1,8 @@ |
|||||
|
# Example Configuration for BQ [Hephestos 2](http://www.bq.com/uk/hephestos-2) |
||||
|
This configuration file is based on the original configuration file shipped with the heavily modified Marlin fork by BQ. The original firmware and configuration file can be found at [BQ Github repository](https://github.com/bq/Marlin). |
||||
|
|
||||
|
NOTE: The look and feel of the Hephestos 2 while navigating the LCD menu will change by using the original Marlin firmware. |
||||
|
|
||||
|
## Changelog |
||||
|
* 2016/03/01 - Initial release |
||||
|
* 2016/03/21 - Activated four point auto leveling by default; updated miscellaneous z-probe values |
||||
@ -0,0 +1,944 @@ |
|||||
|
#ifndef CONFIGURATION_H |
||||
|
#define CONFIGURATION_H |
||||
|
|
||||
|
#include "boards.h" |
||||
|
#include "macros.h" |
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= Getting Started =============================
|
||||
|
//===========================================================================
|
||||
|
/*
|
||||
|
Here are some standard links for getting your machine calibrated: |
||||
|
* http://reprap.org/wiki/Calibration
|
||||
|
* http://youtu.be/wAL9d7FgInk
|
||||
|
* http://calculator.josefprusa.cz
|
||||
|
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
* http://www.thingiverse.com/thing:5573
|
||||
|
* https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
|
||||
|
* http://www.thingiverse.com/thing:298812
|
||||
|
*/ |
||||
|
|
||||
|
// This configuration file contains the basic settings.
|
||||
|
// Advanced settings can be found in Configuration_adv.h
|
||||
|
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= DELTA Printer ===============================
|
||||
|
//===========================================================================
|
||||
|
// For a Delta printer replace the configuration files with the files in the
|
||||
|
// example_configurations/delta directory.
|
||||
|
//
|
||||
|
|
||||
|
#define DELTA |
||||
|
#if ENABLED(DELTA) |
||||
|
|
||||
|
// Make delta curves from many straight lines (linear interpolation).
|
||||
|
// This is a trade-off between visible corners (not enough segments)
|
||||
|
// and processor overload (too many expensive sqrt calls).
|
||||
|
#define DELTA_SEGMENTS_PER_SECOND 160 |
||||
|
|
||||
|
// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
|
||||
|
|
||||
|
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
|
#define DELTA_DIAGONAL_ROD 317.3 + 2.5 // mm
|
||||
|
|
||||
|
// Horizontal offset from middle of printer to smooth rod center.
|
||||
|
#define DELTA_SMOOTH_ROD_OFFSET 220.1 // mm
|
||||
|
|
||||
|
// Horizontal offset of the universal joints on the end effector.
|
||||
|
#define DELTA_EFFECTOR_OFFSET 24.0 // mm
|
||||
|
|
||||
|
// Horizontal offset of the universal joints on the carriages.
|
||||
|
#define DELTA_CARRIAGE_OFFSET 22.0 // mm
|
||||
|
|
||||
|
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
|
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET + 1) |
||||
|
|
||||
|
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
|
#define DELTA_PRINTABLE_RADIUS 140.0 |
||||
|
|
||||
|
#endif |
||||
|
|
||||
|
// @section info
|
||||
|
|
||||
|
#if ENABLED(USE_AUTOMATIC_VERSIONING) |
||||
|
#include "_Version.h" |
||||
|
#else |
||||
|
#include "Default_Version.h" |
||||
|
#endif |
||||
|
|
||||
|
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
|
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
|
// build by the user have been successfully uploaded into firmware.
|
||||
|
#define STRING_CONFIG_H_AUTHOR "(oxivanisher)" // Who made the changes.
|
||||
|
#define SHOW_BOOTSCREEN |
||||
|
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
|
||||
|
#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
|
||||
|
|
||||
|
// @section machine
|
||||
|
|
||||
|
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
||||
|
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
||||
|
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
||||
|
// :[0,1,2,3,4,5,6,7]
|
||||
|
#define SERIAL_PORT 0 |
||||
|
|
||||
|
// This determines the communication speed of the printer
|
||||
|
// :[2400,9600,19200,38400,57600,115200,250000]
|
||||
|
#define BAUDRATE 250000 |
||||
|
|
||||
|
// Enable the Bluetooth serial interface on AT90USB devices
|
||||
|
//#define BLUETOOTH
|
||||
|
|
||||
|
// The following define selects which electronics board you have.
|
||||
|
// Please choose the name from boards.h that matches your setup
|
||||
|
#ifndef MOTHERBOARD |
||||
|
#define MOTHERBOARD BOARD_RAMPS_14_EFB |
||||
|
#endif |
||||
|
|
||||
|
// Optional custom name for your RepStrap or other custom machine
|
||||
|
// Displayed in the LCD "Ready" message
|
||||
|
#define CUSTOM_MACHINE_NAME "Kossel k800XL" |
||||
|
|
||||
|
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
||||
|
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
|
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
|
||||
|
// This defines the number of extruders
|
||||
|
// :[1,2,3,4]
|
||||
|
#define EXTRUDERS 1 |
||||
|
|
||||
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
|
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
|
//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
|
//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
|
||||
|
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
|
// 1 = ATX
|
||||
|
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||
|
// :{1:'ATX',2:'X-Box 360'}
|
||||
|
|
||||
|
#define POWER_SUPPLY 2 |
||||
|
|
||||
|
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
|
#define PS_DEFAULT_OFF |
||||
|
|
||||
|
// @section temperature
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= Thermal Settings ============================
|
||||
|
//===========================================================================
|
||||
|
//
|
||||
|
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
||||
|
//
|
||||
|
//// Temperature sensor settings:
|
||||
|
// -3 is thermocouple with MAX31855 (only for sensor 0)
|
||||
|
// -2 is thermocouple with MAX6675 (only for sensor 0)
|
||||
|
// -1 is thermocouple with AD595
|
||||
|
// 0 is not used
|
||||
|
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
||||
|
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
||||
|
// 3 is Mendel-parts thermistor (4.7k pullup)
|
||||
|
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
||||
|
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
||||
|
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
||||
|
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
||||
|
// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
|
||||
|
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||||
|
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||||
|
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
|
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
|
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
|
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||||
|
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
|
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
|
// 70 is the 100K thermistor found in the bq Hephestos 2
|
||||
|
//
|
||||
|
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
||||
|
// (but gives greater accuracy and more stable PID)
|
||||
|
// 51 is 100k thermistor - EPCOS (1k pullup)
|
||||
|
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
||||
|
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
|
||||
|
//
|
||||
|
// 1047 is Pt1000 with 4k7 pullup
|
||||
|
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
|
// 147 is Pt100 with 4k7 pullup
|
||||
|
// 110 is Pt100 with 1k pullup (non standard)
|
||||
|
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
|
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
|
//#define DUMMY_THERMISTOR_998_VALUE 25
|
||||
|
//#define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-3': "Thermocouple + MAX31855 (only for sensor 0)", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
|
||||
|
#define TEMP_SENSOR_0 5 |
||||
|
#define TEMP_SENSOR_1 0 |
||||
|
#define TEMP_SENSOR_2 0 |
||||
|
#define TEMP_SENSOR_3 0 |
||||
|
#define TEMP_SENSOR_BED 5 |
||||
|
|
||||
|
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
|
||||
|
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
|
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 |
||||
|
|
||||
|
// Actual temperature must be close to target for this long before M109 returns success
|
||||
|
#define TEMP_RESIDENCY_TIME 10 // (seconds)
|
||||
|
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
|
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
|
||||
|
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
||||
|
// to check that the wiring to the thermistor is not broken.
|
||||
|
// Otherwise this would lead to the heater being powered on all the time.
|
||||
|
#define HEATER_0_MINTEMP 5 |
||||
|
#define HEATER_1_MINTEMP 5 |
||||
|
#define HEATER_2_MINTEMP 5 |
||||
|
#define HEATER_3_MINTEMP 5 |
||||
|
#define BED_MINTEMP 5 |
||||
|
|
||||
|
// When temperature exceeds max temp, your heater will be switched off.
|
||||
|
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
|
// You should use MINTEMP for thermistor short/failure protection.
|
||||
|
#define HEATER_0_MAXTEMP 275 |
||||
|
#define HEATER_1_MAXTEMP 275 |
||||
|
#define HEATER_2_MAXTEMP 275 |
||||
|
#define HEATER_3_MAXTEMP 275 |
||||
|
#define BED_MAXTEMP 150 |
||||
|
|
||||
|
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
|
||||
|
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R
|
||||
|
//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= PID Settings ================================
|
||||
|
//===========================================================================
|
||||
|
// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
|
||||
|
|
||||
|
// Comment the following line to disable PID and enable bang-bang.
|
||||
|
#define PIDTEMP |
||||
|
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
|
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
|
#if ENABLED(PIDTEMP) |
||||
|
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
|
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
|
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
|
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
|
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
|
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
|
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
|
#define K1 0.95 //smoothing factor within the PID
|
||||
|
|
||||
|
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
|
// oXis Kossel k800 XL
|
||||
|
#define DEFAULT_Kp 22.04 |
||||
|
#define DEFAULT_Ki 1.65 |
||||
|
#define DEFAULT_Kd 73.67 |
||||
|
|
||||
|
// Kossel k800 XL
|
||||
|
//#define DEFAULT_Kp 22.25
|
||||
|
//#define DEFAULT_Ki 1.45
|
||||
|
//#define DEFAULT_Kd 85.30
|
||||
|
|
||||
|
// MakerGear
|
||||
|
//#define DEFAULT_Kp 7.0
|
||||
|
//#define DEFAULT_Ki 0.1
|
||||
|
//#define DEFAULT_Kd 12
|
||||
|
|
||||
|
// Mendel Parts V9 on 12V
|
||||
|
//#define DEFAULT_Kp 63.0
|
||||
|
//#define DEFAULT_Ki 2.25
|
||||
|
//#define DEFAULT_Kd 440
|
||||
|
|
||||
|
#endif // PIDTEMP
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= PID > Bed Temperature Control ===============
|
||||
|
//===========================================================================
|
||||
|
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
|
//
|
||||
|
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
|
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
|
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
|
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
|
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
|
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
|
// If this is enabled, find your own PID constants below.
|
||||
|
//#define PIDTEMPBED
|
||||
|
|
||||
|
//#define BED_LIMIT_SWITCHING
|
||||
|
|
||||
|
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
|
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
|
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
|
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
|
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
|
||||
|
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
|
|
||||
|
#if ENABLED(PIDTEMPBED) |
||||
|
|
||||
|
#define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
|
||||
|
|
||||
|
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
|
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
|
#define DEFAULT_bedKp 15.00 |
||||
|
#define DEFAULT_bedKi .04 |
||||
|
#define DEFAULT_bedKd 305.4 |
||||
|
|
||||
|
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
|
//from pidautotune
|
||||
|
//#define DEFAULT_bedKp 97.1
|
||||
|
//#define DEFAULT_bedKi 1.41
|
||||
|
//#define DEFAULT_bedKd 1675.16
|
||||
|
|
||||
|
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
|
#endif // PIDTEMPBED
|
||||
|
|
||||
|
// @section extruder
|
||||
|
|
||||
|
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
|
//can be software-disabled for whatever purposes by
|
||||
|
#define PREVENT_DANGEROUS_EXTRUDE |
||||
|
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
||||
|
#define PREVENT_LENGTHY_EXTRUDE |
||||
|
|
||||
|
#define EXTRUDE_MINTEMP 170 |
||||
|
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//======================== Thermal Runaway Protection =======================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
/**
|
||||
|
* Thermal Protection protects your printer from damage and fire if a |
||||
|
* thermistor falls out or temperature sensors fail in any way. |
||||
|
* |
||||
|
* The issue: If a thermistor falls out or a temperature sensor fails, |
||||
|
* Marlin can no longer sense the actual temperature. Since a disconnected |
||||
|
* thermistor reads as a low temperature, the firmware will keep the heater on. |
||||
|
* |
||||
|
* If you get "Thermal Runaway" or "Heating failed" errors the |
||||
|
* details can be tuned in Configuration_adv.h |
||||
|
*/ |
||||
|
|
||||
|
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
|
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= Mechanical Settings =========================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
// @section machine
|
||||
|
|
||||
|
// Uncomment this option to enable CoreXY kinematics
|
||||
|
//#define COREXY
|
||||
|
|
||||
|
// Uncomment this option to enable CoreXZ kinematics
|
||||
|
//#define COREXZ
|
||||
|
|
||||
|
// Enable this option for Toshiba steppers
|
||||
|
//#define CONFIG_STEPPERS_TOSHIBA
|
||||
|
|
||||
|
// @section homing
|
||||
|
|
||||
|
// coarse Endstop Settings
|
||||
|
//#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
|
||||
|
#if DISABLED(ENDSTOPPULLUPS) |
||||
|
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
|
#define ENDSTOPPULLUP_XMAX |
||||
|
#define ENDSTOPPULLUP_YMAX |
||||
|
#define ENDSTOPPULLUP_ZMAX |
||||
|
//#define ENDSTOPPULLUP_XMIN
|
||||
|
//#define ENDSTOPPULLUP_YMIN
|
||||
|
#define ENDSTOPPULLUP_ZMIN |
||||
|
//#define ENDSTOPPULLUP_ZMIN_PROBE
|
||||
|
#endif |
||||
|
|
||||
|
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
|
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
//#define DISABLE_MAX_ENDSTOPS
|
||||
|
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================= Z Probe Options =============================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
|
||||
|
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
|
||||
|
//
|
||||
|
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
|
||||
|
//
|
||||
|
// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
|
||||
|
// Example: To park the head outside the bed area when homing with G28.
|
||||
|
//
|
||||
|
// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
|
||||
|
//
|
||||
|
// For a servo-based Z probe, you must set up servo support below, including
|
||||
|
// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and SERVO_ENDSTOP_ANGLES.
|
||||
|
//
|
||||
|
// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
|
||||
|
// - Use 5V for powered (usu. inductive) sensors.
|
||||
|
// - Otherwise connect:
|
||||
|
// - normally-closed switches to GND and D32.
|
||||
|
// - normally-open switches to 5V and D32.
|
||||
|
//
|
||||
|
// Normally-closed switches are advised and are the default.
|
||||
|
//
|
||||
|
// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
|
||||
|
// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
|
||||
|
// default pin for all RAMPS-based boards. Some other boards map differently.
|
||||
|
// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
|
||||
|
//
|
||||
|
// WARNING:
|
||||
|
// Setting the wrong pin may have unexpected and potentially disastrous consequences.
|
||||
|
// Use with caution and do your homework.
|
||||
|
//
|
||||
|
//#define Z_MIN_PROBE_ENDSTOP
|
||||
|
|
||||
|
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
|
||||
|
// The Z_MIN_PIN will then be used for both Z-homing and probing.
|
||||
|
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN |
||||
|
|
||||
|
// To use a probe you must enable one of the two options above!
|
||||
|
|
||||
|
// This option disables the use of the Z_MIN_PROBE_PIN
|
||||
|
// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
|
||||
|
// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
|
||||
|
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
|
||||
|
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
||||
|
|
||||
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
|
// :{0:'Low',1:'High'}
|
||||
|
#define X_ENABLE_ON 0 |
||||
|
#define Y_ENABLE_ON 0 |
||||
|
#define Z_ENABLE_ON 0 |
||||
|
#define E_ENABLE_ON 0 // For all extruders
|
||||
|
|
||||
|
// Disables axis stepper immediately when it's not being used.
|
||||
|
// WARNING: When motors turn off there is a chance of losing position accuracy!
|
||||
|
#define DISABLE_X false |
||||
|
#define DISABLE_Y false |
||||
|
#define DISABLE_Z false |
||||
|
// Warn on display about possibly reduced accuracy
|
||||
|
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
||||
|
|
||||
|
// @section extruder
|
||||
|
|
||||
|
#define DISABLE_E false // For all extruders
|
||||
|
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
|
||||
|
// @section machine
|
||||
|
|
||||
|
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
|
#define INVERT_X_DIR false |
||||
|
#define INVERT_Y_DIR false |
||||
|
#define INVERT_Z_DIR false |
||||
|
|
||||
|
// @section extruder
|
||||
|
|
||||
|
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
|
#define INVERT_E0_DIR true |
||||
|
#define INVERT_E1_DIR false |
||||
|
#define INVERT_E2_DIR false |
||||
|
#define INVERT_E3_DIR false |
||||
|
|
||||
|
// @section homing
|
||||
|
//#define MIN_Z_HEIGHT_FOR_HOMING 7 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
|
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
|
||||
|
// ENDSTOP SETTINGS:
|
||||
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
// :[-1,1]
|
||||
|
#define X_HOME_DIR 1 |
||||
|
#define Y_HOME_DIR 1 |
||||
|
#define Z_HOME_DIR 1 |
||||
|
|
||||
|
#define min_software_endstops false // If true, axis won't move to coordinates less than HOME_POS.
|
||||
|
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
|
||||
|
// @section machine
|
||||
|
|
||||
|
// Travel limits after homing (units are in mm)
|
||||
|
#define X_MIN_POS -DELTA_PRINTABLE_RADIUS |
||||
|
#define Y_MIN_POS -DELTA_PRINTABLE_RADIUS |
||||
|
#define Z_MIN_POS 0 |
||||
|
#define X_MAX_POS DELTA_PRINTABLE_RADIUS |
||||
|
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS |
||||
|
#define Z_MAX_POS MANUAL_Z_HOME_POS |
||||
|
|
||||
|
//===========================================================================
|
||||
|
//========================= Filament Runout Sensor ==========================
|
||||
|
//===========================================================================
|
||||
|
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
|
||||
|
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
|
||||
|
// It is assumed that when logic high = filament available
|
||||
|
// when logic low = filament ran out
|
||||
|
#if ENABLED(FILAMENT_RUNOUT_SENSOR) |
||||
|
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
|
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
|
#define FILAMENT_RUNOUT_SCRIPT "M600" |
||||
|
#endif |
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================ Mesh Bed Leveling ============================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
//#define MESH_BED_LEVELING // Enable mesh bed leveling.
|
||||
|
|
||||
|
#if ENABLED(MESH_BED_LEVELING) |
||||
|
#define MESH_MIN_X 10 |
||||
|
#define MESH_MAX_X (X_MAX_POS - (MESH_MIN_X)) |
||||
|
#define MESH_MIN_Y 10 |
||||
|
#define MESH_MAX_Y (Y_MAX_POS - (MESH_MIN_Y)) |
||||
|
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
|
#define MESH_NUM_Y_POINTS 3 |
||||
|
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
|
||||
|
|
||||
|
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
|
||||
|
|
||||
|
#if ENABLED(MANUAL_BED_LEVELING) |
||||
|
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
||||
|
#endif // MANUAL_BED_LEVELING
|
||||
|
|
||||
|
#endif // MESH_BED_LEVELING
|
||||
|
|
||||
|
//===========================================================================
|
||||
|
//============================ Bed Auto Leveling ============================
|
||||
|
//===========================================================================
|
||||
|
|
||||
|
// @section bedlevel
|
||||
|
|
||||
|
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||
|
//#define DEBUG_LEVELING_FEATURE
|
||||
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
|
|
||||
|
#if ENABLED(AUTO_BED_LEVELING_FEATURE) |
||||
|
|
||||
|
// There are 2 different ways to specify probing locations:
|
||||
|
//
|
||||
|
// - "grid" mode
|
||||
|
// Probe several points in a rectangular grid.
|
||||
|
// You specify the rectangle and the density of sample points.
|
||||
|
// This mode is preferred because there are more measurements.
|
||||
|
//
|
||||
|
// - "3-point" mode
|
||||
|
// Probe 3 arbitrary points on the bed (that aren't collinear)
|
||||
|
// You specify the XY coordinates of all 3 points.
|
||||
|
|
||||
|
// Enable this to sample the bed in a grid (least squares solution).
|
||||
|
// Note: this feature generates 10KB extra code size.
|
||||
|
#define AUTO_BED_LEVELING_GRID |
||||
|
|
||||
|
#if ENABLED(AUTO_BED_LEVELING_GRID) |
||||
|
|
||||
|
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10) |
||||
|
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS |
||||
|
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS |
||||
|
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS |
||||
|
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS |
||||
|
|
||||
|
#define MIN_PROBE_EDGE 20 // The Z probe minimum square sides can be no smaller than this.
|
||||
|
|
||||
|
// Non-linear bed leveling will be used.
|
||||
|
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||
|
// Useful for deltas where the print surface may appear like a bowl or dome shape.
|
||||
|
// Works best with AUTO_BED_LEVELING_GRID_POINTS 5 or higher.
|
||||
|
#define AUTO_BED_LEVELING_GRID_POINTS 7 |
||||
|
|
||||
|
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
|
||||
|
// Arbitrary points to probe.
|
||||
|
// A simple cross-product is used to estimate the plane of the bed.
|
||||
|
#define ABL_PROBE_PT_1_X 15 |
||||
|
#define ABL_PROBE_PT_1_Y 180 |
||||
|
#define ABL_PROBE_PT_2_X 15 |
||||
|
#define ABL_PROBE_PT_2_Y 20 |
||||
|
#define ABL_PROBE_PT_3_X 170 |
||||
|
#define ABL_PROBE_PT_3_Y 20 |
||||
|
|
||||
|
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
|
||||
|
// Z Probe to nozzle (X,Y) offset, relative to (0, 0).
|
||||
|
// X and Y offsets must be integers.
|
||||
|
//
|
||||
|
// In the following example the X and Y offsets are both positive:
|
||||
|
// #define X_PROBE_OFFSET_FROM_EXTRUDER 10
|
||||
|
// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
|
||||
|
//
|
||||
|
// +-- BACK ---+
|
||||
|
// | |
|
||||
|
// L | (+) P | R <-- probe (20,20)
|
||||
|
// E | | I
|
||||
|
// F | (-) N (+) | G <-- nozzle (10,10)
|
||||
|
// T | | H
|
||||
|
// | (-) | T
|
||||
|
// | |
|
||||
|
// O-- FRONT --+
|
||||
|
// (0,0)
|
||||
|
#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // X offset: -left [of the nozzle] +right
|
||||
|
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Y offset: -front [of the nozzle] +behind
|
||||
|
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z offset: -below [the nozzle] (always negative!)
|
||||
|
|
||||
|
#define XY_TRAVEL_SPEED 7000 // X and Y axis travel speed between probes, in mm/min.
|
||||
|
|
||||
|
#define Z_RAISE_BEFORE_PROBING 20 // How much the Z axis will be raised before traveling to the first probing point.
|
||||
|
#define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points.
|
||||
|
#define Z_RAISE_AFTER_PROBING 20 // How much the Z axis will be raised after the last probing point.
|
||||
|
|
||||
|
#define Z_PROBE_END_SCRIPT "G1 Z20 X0 Y0 F7000" |
||||
|
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
|
||||
|
// Useful to retract a deployable Z probe.
|
||||
|
|
||||
|
// Probes are sensors/switches that need to be activated before they can be used
|
||||
|
// and deactivated after the use.
|
||||
|
// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE
|
||||
|
|
||||
|
// A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER
|
||||
|
// when the hardware endstops are active.
|
||||
|
//#define FIX_MOUNTED_PROBE
|
||||
|
|
||||
|
// A Servo Probe can be defined in the servo section below.
|
||||
|
|
||||
|
// An Allen Key Probe is currently predefined only in the delta example configurations.
|
||||
|
|
||||
|
//#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
|
||||
|
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
|
||||
|
// it is highly recommended you leave Z_SAFE_HOMING enabled!
|
||||
|
|
||||
|
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
|
||||
|
// This feature is meant to avoid Z homing with Z probe outside the bed area.
|
||||
|
// When defined, it will:
|
||||
|
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
|
||||
|
// - If stepper drivers timeout, it will need X and Y homing again before Z homing.
|
||||
|
// - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28).
|
||||
|
// - Block Z homing only when the Z probe is outside bed area.
|
||||
|
|
||||
|
#if ENABLED(Z_SAFE_HOMING) |
||||
|
|
||||
|
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
|
||||
|
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
|
||||
|
|
||||
|
#endif |
||||
|
|
||||
|
#endif // AUTO_BED_LEVELING_FEATURE
|
||||
|
|
||||
|
|
||||
|
// @section homing
|
||||
|
|
||||
|
// The position of the homing switches
|
||||
|
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
|
#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
|
|
||||
|
// Manual homing switch locations:
|
||||
|
// For deltabots this means top and center of the Cartesian print volume.
|
||||
|
#if ENABLED(MANUAL_HOME_POSITIONS) |
||||
|
#define MANUAL_X_HOME_POS 0 |
||||
|
#define MANUAL_Y_HOME_POS 0 |
||||
|
#define MANUAL_Z_HOME_POS 386.5 // For delta: Distance between nozzle and print surface after homing.
|
||||
|
#endif |
||||
|
|
||||
|
// @section movement
|
||||
|
|
||||
|
/**
|
||||
|
* MOVEMENT SETTINGS |
||||
|
*/ |
||||
|
|
||||
|
#define HOMING_FEEDRATE {60*60, 60*60, 60*60, 0} // set the homing speeds (mm/min)
|
||||
|
|
||||
|
// default settings
|
||||
|
#define XYZ_FULL_STEPS_PER_ROTATION 200 |
||||
|
#define XYZ_MICROSTEPS 16 |
||||
|
#define XYZ_BELT_PITCH 2 |
||||
|
#define XYZ_PULLEY_TEETH 16 |
||||
|
#define XYZ_STEPS ((XYZ_FULL_STEPS_PER_ROTATION) * (XYZ_MICROSTEPS) / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH)) |
||||
|
|
||||
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 158} // default steps per unit for PowerWasp
|
||||
|
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec)
|
||||
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
|
||||
|
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
|
||||
|
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
|
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
|
#define DEFAULT_ZJERK 20.0 // (mm/sec)
|
||||
|
#define DEFAULT_EJERK 20.0 // (mm/sec)
|
||||
|
|
||||
|
|
||||
|
//=============================================================================
|
||||
|
//============================= Additional Features ===========================
|
||||
|
//=============================================================================
|
||||
|
|
||||
|
// @section more
|
||||
|
|
||||
|
// Custom M code points
|
||||
|
#define CUSTOM_M_CODES |
||||
|
#if ENABLED(CUSTOM_M_CODES) |
||||
|
#if ENABLED(AUTO_BED_LEVELING_FEATURE) |
||||
|
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851 |
||||
|
#define Z_PROBE_OFFSET_RANGE_MIN -20 |
||||
|
#define Z_PROBE_OFFSET_RANGE_MAX 20 |
||||
|
#endif |
||||
|
#endif |
||||
|
|
||||
|
// @section extras
|
||||
|
|
||||
|
// EEPROM
|
||||
|
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
|
// M500 - stores parameters in EEPROM
|
||||
|
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
|
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
|
//define this to enable EEPROM support
|
||||
|
#define EEPROM_SETTINGS |
||||
|
|
||||
|
#if ENABLED(EEPROM_SETTINGS) |
||||
|
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
|
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
|
#endif |
||||
|
|
||||
|
//
|
||||
|
// Host Keepalive
|
||||
|
//
|
||||
|
// By default Marlin will send a busy status message to the host
|
||||
|
// every 2 seconds when it can't accept commands.
|
||||
|
//
|
||||
|
//#define DISABLE_HOST_KEEPALIVE // Enable this option if your host doesn't like keepalive messages.
|
||||
|
|
||||
|
//
|
||||
|
// M100 Free Memory Watcher
|
||||
|
//
|
||||
|
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
|
||||
|
|
||||
|
// @section temperature
|
||||
|
|
||||
|
// Preheat Constants
|
||||
|
#define PLA_PREHEAT_HOTEND_TEMP 180 |
||||
|
#define PLA_PREHEAT_HPB_TEMP 70 |
||||
|
#define PLA_PREHEAT_FAN_SPEED 100 // Insert Value between 0 and 255
|
||||
|
|
||||
|
#define ABS_PREHEAT_HOTEND_TEMP 240 |
||||
|
#define ABS_PREHEAT_HPB_TEMP 110 |
||||
|
#define ABS_PREHEAT_FAN_SPEED 100 // Insert Value between 0 and 255
|
||||
|
|
||||
|
//==============================LCD and SD support=============================
|
||||
|
// @section lcd
|
||||
|
|
||||
|
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
|
// en, pl, fr, de, es, ru, bg, it, pt, pt_utf8, pt-br, pt-br_utf8, fi, an, nl, ca, eu, kana, kana_utf8, cn, cz, test
|
||||
|
// See also language.h
|
||||
|
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) |
||||
|
|
||||
|
// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
|
||||
|
// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
|
||||
|
// See also https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
|
||||
|
#define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware
|
||||
|
//#define DISPLAY_CHARSET_HD44780_WESTERN
|
||||
|
//#define DISPLAY_CHARSET_HD44780_CYRILLIC
|
||||
|
|
||||
|
//#define ULTRA_LCD //general LCD support, also 16x2
|
||||
|
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
|
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||
|
// Changed behaviour! If you need SDSUPPORT uncomment it!
|
||||
|
//#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
||||
|
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
|
||||
|
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
||||
|
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
||||
|
//#define REVERSE_MENU_DIRECTION // When enabled CLOCKWISE moves UP in the LCD menu
|
||||
|
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
|
//#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
|
//#define SPEAKER // The sound device is a speaker - not a buzzer. A buzzer resonates with his own frequency.
|
||||
|
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
|
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
|
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||
|
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
|
// http://reprap.org/wiki/PanelOne
|
||||
|
//#define PANEL_ONE
|
||||
|
|
||||
|
// The MaKr3d Makr-Panel with graphic controller and SD support
|
||||
|
// http://reprap.org/wiki/MaKr3d_MaKrPanel
|
||||
|
//#define MAKRPANEL
|
||||
|
|
||||
|
// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
|
||||
|
// http://panucatt.com
|
||||
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||
|
//#define VIKI2
|
||||
|
//#define miniVIKI
|
||||
|
|
||||
|
// This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
|
||||
|
//
|
||||
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||
|
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
||||
|
//#define SD_DETECT_INVERTED
|
||||
|
|
||||
|
// The RepRapDiscount Smart Controller (white PCB)
|
||||
|
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
||||
|
#define REPRAP_DISCOUNT_SMART_CONTROLLER |
||||
|
|
||||
|
// The GADGETS3D G3D LCD/SD Controller (blue PCB)
|
||||
|
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
|
||||
|
//#define G3D_PANEL
|
||||
|
|
||||
|
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
|
||||
|
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
|
//
|
||||
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||
|
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
|
||||
|
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||||
|
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
|
||||
|
//#define REPRAPWORLD_KEYPAD
|
||||
|
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
|
||||
|
|
||||
|
// The Elefu RA Board Control Panel
|
||||
|
// http://www.elefu.com/index.php?route=product/product&product_id=53
|
||||
|
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||
|
//#define RA_CONTROL_PANEL
|
||||
|
|
||||
|
// The MakerLab Mini Panel with graphic controller and SD support
|
||||
|
// http://reprap.org/wiki/Mini_panel
|
||||
|
//#define MINIPANEL
|
||||
|
|
||||
|
/**
|
||||
|
* I2C Panels |
||||
|
*/ |
||||
|
|
||||
|
//#define LCD_I2C_SAINSMART_YWROBOT
|
||||
|
|
||||
|
//#define LCM1602 // LCM1602 Adapter for 16x2 LCD
|
||||
|
|
||||
|
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||||
|
//
|
||||
|
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
|
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
|
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
|
||||
|
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
|
||||
|
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
|
//#define LCD_I2C_PANELOLU2
|
||||
|
|
||||
|
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
|
//#define LCD_I2C_VIKI
|
||||
|
|
||||
|
// SSD1306 OLED generic display support
|
||||
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||
|
//#define U8GLIB_SSD1306
|
||||
|
|
||||
|
// Shift register panels
|
||||
|
// ---------------------
|
||||
|
// 2 wire Non-latching LCD SR from:
|
||||
|
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
|
//#define SAV_3DLCD
|
||||
|
|
||||
|
// @section extras
|
||||
|
|
||||
|
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
|
//#define FAST_PWM_FAN
|
||||
|
|
||||
|
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||||
|
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
|
// is too low, you should also increment SOFT_PWM_SCALE.
|
||||
|
//#define FAN_SOFT_PWM
|
||||
|
|
||||
|
// Incrementing this by 1 will double the software PWM frequency,
|
||||
|
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
||||
|
// However, control resolution will be halved for each increment;
|
||||
|
// at zero value, there are 128 effective control positions.
|
||||
|
#define SOFT_PWM_SCALE 0 |
||||
|
|
||||
|
// Temperature status LEDs that display the hotend and bet temperature.
|
||||
|
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
|
// Otherwise the RED led is on. There is 1C hysteresis.
|
||||
|
//#define TEMP_STAT_LEDS
|
||||
|
|
||||
|
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
||||
|
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
|
//#define PHOTOGRAPH_PIN 23
|
||||
|
|
||||
|
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
|
//#define SF_ARC_FIX
|
||||
|
|
||||
|
// Support for the BariCUDA Paste Extruder.
|
||||
|
//#define BARICUDA
|
||||
|
|
||||
|
//define BlinkM/CyzRgb Support
|
||||
|
//#define BLINKM
|
||||
|
|
||||
|
/*********************************************************************\
|
||||
|
* R/C SERVO support |
||||
|
* Sponsored by TrinityLabs, Reworked by codexmas |
||||
|
**********************************************************************/ |
||||
|
|
||||
|
// Number of servos
|
||||
|
//
|
||||
|
// If you select a configuration below, this will receive a default value and does not need to be set manually
|
||||
|
// set it manually if you have more servos than extruders and wish to manually control some
|
||||
|
// leaving it undefined or defining as 0 will disable the servo subsystem
|
||||
|
// If unsure, leave commented / disabled
|
||||
|
//
|
||||
|
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
||||
|
|
||||
|
// Servo Endstops
|
||||
|
//
|
||||
|
// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
|
||||
|
// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500.
|
||||
|
//
|
||||
|
//#define X_ENDSTOP_SERVO_NR 1
|
||||
|
//#define Y_ENDSTOP_SERVO_NR 2
|
||||
|
//#define Z_ENDSTOP_SERVO_NR 0
|
||||
|
//#define SERVO_ENDSTOP_ANGLES {{0,0}, {0,0}, {70,0}} // X,Y,Z Axis Extend and Retract angles
|
||||
|
|
||||
|
// Servo deactivation
|
||||
|
//
|
||||
|
// With this option servos are powered only during movement, then turned off to prevent jitter.
|
||||
|
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
|
||||
|
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) |
||||
|
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
|
||||
|
// 300ms is a good value but you can try less delay.
|
||||
|
// If the servo can't reach the requested position, increase it.
|
||||
|
#define SERVO_DEACTIVATION_DELAY 300 |
||||
|
#endif |
||||
|
|
||||
|
/**********************************************************************\
|
||||
|
* Support for a filament diameter sensor |
||||
|
* Also allows adjustment of diameter at print time (vs at slicing) |
||||
|
* Single extruder only at this point (extruder 0) |
||||
|
* |
||||
|
* Motherboards |
||||
|
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector |
||||
|
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) |
||||
|
* 301 - Rambo - uses Analog input 3 |
||||
|
* Note may require analog pins to be defined for different motherboards |
||||
|
**********************************************************************/ |
||||
|
// Uncomment below to enable
|
||||
|
//#define FILAMENT_SENSOR
|
||||
|
|
||||
|
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
|
|
||||
|
#if ENABLED(FILAMENT_SENSOR) |
||||
|
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
|
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
|
||||
|
#define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm
|
||||
|
#define MEASURED_LOWER_LIMIT 1.60 //lower limit factor for sensor reading validation in mm
|
||||
|
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
|
||||
|
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
|
||||
|
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
|
||||
|
//#define FILAMENT_LCD_DISPLAY
|
||||
|
#endif |
||||
|
|
||||
|
#include "Configuration_adv.h" |
||||
|
#include "thermistortables.h" |
||||
|
|
||||
|
#endif //CONFIGURATION_H
|
||||
@ -0,0 +1,21 @@ |
|||||
|
# Configuration for Kossel k800 XL |
||||
|
This example configuration ist for a Kossel XL with a printable bed diameter of 280mm and a height of 385mm. It also has the auto bed leveling probe (with a endstop switch) and the heat bed activated. |
||||
|
|
||||
|
## Configuration |
||||
|
You might have/want to edit at least the following settings in Configuration.h: |
||||
|
* <code>MANUAL_Z_HOME_POS<code> The hight of your printing space available, auto bed leveling makes this not as important as before |
||||
|
* <code>DELTA_PRINTABLE_RADIUS</code> The printable radius |
||||
|
* <code>DEFAULT_AXIS_STEPS_PER_UNIT</code> [http://zennmaster.com/makingstuff/reprap-101-calibrating-your-extruder-part-1-e-steps](The steps for the extruder to optimize the amount of filament flow) |
||||
|
|
||||
|
### Fine tuning |
||||
|
* Increase <code>DELTA_RADIUS</code> when the model is convex (bulge in the middle) |
||||
|
* Increase <code>DELTA_DIAGONAL_ROD</code> when the model is larger then expected |
||||
|
|
||||
|
### [http://reprap.org/wiki/PID_Tuning](PID Tuning) |
||||
|
* <code>DEFAULT_Kp</code> (PID tuning for the hotend) |
||||
|
* <code>DEFAULT_Ki</code> (PID tuning for the hotend) |
||||
|
* <code>DEFAULT_Kd</code> (PID tuning for the hotend) |
||||
|
|
||||
|
### PSU Options |
||||
|
* The power supply is configured to 2 (to use a relay to switch 12V on and off) |
||||
|
* It is configured to be off by default |
||||
Some files were not shown because too many files changed in this diff
Loading…
Reference in new issue