From dd06017f642b0396389e85796e447ecee47fdd4b Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Wed, 19 Jun 2019 01:03:24 -0500 Subject: [PATCH] Bring configs up to date --- Marlin/Configuration_adv.h | 4 ++-- config/examples/Anet/A6/Configuration.h | 3 +-- config/examples/BQ/Hephestos_2/Configuration.h | 2 +- .../Dagoma/Disco Ultimate/Configuration_adv.h | 2 +- config/examples/Einstart-S/Configuration.h | 17 ++++++++++++++--- .../Formbot/Raptor/Configuration_adv.h | 18 +++++++++--------- .../examples/Geeetech/A10/Configuration_adv.h | 2 +- config/examples/Geeetech/A20M/Configuration.h | 1 - .../Geeetech/MeCreator2/Configuration_adv.h | 15 +++++++++++++++ .../Prusa i3 Pro B/bltouch/Configuration.h | 1 + config/examples/JGAurora/A1/Configuration.h | 1 - .../examples/JGAurora/A1/Configuration_adv.h | 2 +- .../examples/JGAurora/A5S/Configuration_adv.h | 2 +- .../Black_STM32F407VET6/Configuration_adv.h | 2 ++ config/examples/Tronxy/X5S/Configuration.h | 3 ++- .../delta/Anycubic/Kossel/Configuration.h | 1 + .../Tevo Little Monster/Configuration_adv.h | 12 ++++++++++++ .../delta/kossel_mini/Configuration_adv.h | 1 + 18 files changed, 65 insertions(+), 24 deletions(-) diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index ee3b619089..24cb61a130 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -917,7 +917,7 @@ */ //#define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. @@ -1159,7 +1159,7 @@ #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. // Note: Extra time may be added to mitigate controller latency. - #define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. #if ENABLED(MOVE_Z_WHEN_IDLE) #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 1fe45195e7..35336af8d9 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -989,15 +989,14 @@ #if 1 // 0 for less clearance #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points -#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 5 // Z position after probing is done #else #define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow #define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points -#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 3 // Z position after probing is done #endif +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping // For M851 give a range for adjusting the Z probe offset diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 39a44bf1f1..b7df3c08c2 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -1299,7 +1299,7 @@ // Homing speeds (mm/m) #define HOMING_FEEDRATE_XY (50*60) -#define HOMING_FEEDRATE_Z ( 4*60) +#define HOMING_FEEDRATE_Z (4*60) // Validate that endstops are triggered on homing moves #define VALIDATE_HOMING_ENDSTOPS diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index e37841ad4b..2b6535ee8c 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -917,7 +917,7 @@ */ //#define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index ea46969022..cfa8a8a6ab 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -379,13 +379,13 @@ * 147 : Pt100 with 4k7 pullup * 110 : Pt100 with 1k pullup (non standard) * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * * Use these for Testing or Development purposes. NEVER for production machine. * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * 666 : Custom table generated for 200K thermistor with 10k pullup on Einstart S - * - * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 666 #define TEMP_SENSOR_1 0 @@ -820,6 +820,7 @@ * or (with LCD_BED_LEVELING) the LCD controller. */ //#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 /** * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. @@ -928,6 +929,7 @@ */ #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 5 // Z position after probing is done #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping @@ -1970,6 +1972,15 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +// +// Extensible UI +// +// Enable third-party or vendor customized user interfaces that aren't +// packaged with Marlin. Source code for the user interface will need to +// be placed in "src/lcd/extensible_ui/lib" +// +//#define EXTENSIBLE_UI + // // Einstart S OLED SSD1306 // diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index e90e5c74a4..ae03cf7601 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -2255,25 +2255,25 @@ #define CUSTOM_USER_MENUS #endif #if ENABLED(CUSTOM_USER_MENUS) - #define CUSTOM_USER_MENU_TITLE "Commissioning" - //#define USER_SCRIPT_DONE "M117 User Script Done" + #define CUSTOM_USER_MENU_TITLE "Commissioning" + //#define USER_SCRIPT_DONE "M117 User Script Done" #define USER_SCRIPT_AUDIBLE_FEEDBACK #define USER_SCRIPT_RETURN // Return to status screen after a script #define USER_DESC_1 "UBL Commission Step 1" - #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 P1 \n G29 S1 \n M117 Run Step 2 \n" + #define USER_GCODE_1 "M502\nM500\nM501\nM190 S75\nG28\nG29 P1\nG29 S1\nM117 Run Step 2" #define USER_DESC_2 "UBL Commission Step 2" - #define USER_GCODE_2 "G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M117 Set Z Offset \n" + #define USER_GCODE_2 "G29 S1\nG29 S0\nG29 F 10.0\nG29 A\nM500\nG28\nG29 L1\nM109 S225\nG1 X150 Y 150\nG1 Z0\nM117 Set Z Offset" #define USER_DESC_3 "Prep for Z Adjust" - #define USER_GCODE_3 "M190 75 \n M104 235 \n G28 \n G29 L1 \n G1 X150 Y 150 \n G1 Z0 \n" + #define USER_GCODE_3 "M190 75\nM104 235\nG28\nG29 L1\nG1 X150 Y 150\nG1 Z0" - #define USER_DESC_4 "Fill Mesh Points" - #define USER_GCODE_4 "G29 P3 \n G29 P3 \n G29 P3 \n G29 T \n" + #define USER_DESC_4 "Fill Mesh Points" + #define USER_GCODE_4 "G29 P3\nG29 P3\nG29 P3\nG29 T" - #define USER_DESC_5 "Run Mesh Validation" - #define USER_GCODE_5 "G26 \n" + #define USER_DESC_5 "Run Mesh Validation" + #define USER_GCODE_5 "G26" #endif /** diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 8ec7846854..fec17c7972 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -917,7 +917,7 @@ */ //#define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 7cc7c4ec9b..cd4c809d7f 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -1694,7 +1694,6 @@ // ULTIPANEL as seen on Thingiverse. // #define ULTIPANEL -#define NEWPANEL // // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index eaaa4d40c2..678fea6af0 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -2218,6 +2218,21 @@ */ #define FASTER_GCODE_PARSER +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + /** * G-code Macros * diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index f35724fc23..ed0b780bb2 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -321,6 +321,7 @@ #define AUTO_POWER_FANS // Turn on PSU if fans need power #define AUTO_POWER_E_FANS #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN #define POWER_TIMEOUT 30 #endif diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index a7d0b2ad45..4d4a40f8ae 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -1982,7 +1982,6 @@ // MKS Robin 320x240 color display // Also used for JGAurora A5S & A1 TFT LCD's (16-bit Parallel LCD via FSMC) #define MKS_ROBIN_TFT -#define PRINTER_EVENT_LEDS //============================================================================= //============================ Other Controllers ============================ diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 8aa1304936..3b1873187a 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -922,7 +922,7 @@ */ //#define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 8aa1304936..3b1873187a 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -922,7 +922,7 @@ */ //#define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) - //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 5a95ba2206..ae1cb02185 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -1166,6 +1166,8 @@ #endif #endif + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 8990e24cd1..b23399d8ff 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -445,7 +445,8 @@ #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) - #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 383b4a3154..e44f2aa704 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -1311,6 +1311,7 @@ //#define AUTO_BED_LEVELING_UBL //#define MESH_BED_LEVELING #endif + /** * Normally G28 leaves leveling disabled on completion. Enable * this option to have G28 restore the prior leveling state. diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 1fd43d6e5c..72a3aee019 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -2236,6 +2236,18 @@ //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode #endif +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + /** * User-defined menu items that execute custom GCode */ diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 3695eed54f..58c6260c48 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -754,6 +754,7 @@ #define CALIBRATION_PIN_PULLUP #endif #endif + /** * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible