andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

G34 Z stepper locking (#20091) 

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
vanilla_fb_2.0.x
InsanityAutomation 4 years ago
committed by Scott Lahteine
parent
7b745345f7
commit
dc949f5488
6 changed files with 341 additions and 298 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 5
      Marlin/src/gcode/calibrate/G28.cpp
  2. 622
      Marlin/src/gcode/calibrate/G34_M422.cpp
  3. 2
      Marlin/src/gcode/gcode.cpp
  4. 2
      Marlin/src/gcode/gcode.h
  5. 7
      Marlin/src/inc/SanityCheck.h
  6. 1
      platformio.ini

5
Marlin/src/gcode/calibrate/G28.cpp
View File

@ -375,6 +375,11 @@ void GcodeSuite::G28() {
// Home Z last if homing towards the bed
#if DISABLED(HOME_Z_FIRST)
if (doZ) {
#if EITHER(Z_MULTI_ENDSTOPS, Z_STEPPER_AUTO_ALIGN)
stepper.set_all_z_lock(false);
stepper.set_separate_multi_axis(false);
#endif
TERN_(BLTOUCH, bltouch.init());
TERN(Z_SAFE_HOMING, home_z_safely(), homeaxis(Z_AXIS));
probe.move_z_after_homing();

622
Marlin/src/gcode/calibrate/G34_M422.cpp
View File

@ -22,7 +22,7 @@
#include "../../inc/MarlinConfigPre.h"
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
#if EITHER(Z_MULTI_ENDSTOPS, Z_STEPPER_AUTO_ALIGN)
#include "../../feature/z_stepper_align.h"
@ -51,364 +51,398 @@
/**
* G34: Z-Stepper automatic alignment
*
* I<iterations>
* T<accuracy>
* A<amplification>
* R<recalculate> points based on current probe offsets
* Manual stepper lock controls (reset by G28):
* L Unlock all steppers
* Z<1-4> Z stepper to lock / unlock
* S<state> 0=UNLOCKED 1=LOCKED. If omitted, assume LOCKED.
*
* Examples:
* G34 Z1 ; Lock Z1
* G34 L Z2 ; Unlock all, then lock Z2
* G34 Z2 S0 ; Unlock Z2
*
* With Z_STEPPER_AUTO_ALIGN:
* I<iterations> Number of tests. If omitted, Z_STEPPER_ALIGN_ITERATIONS.
* T<accuracy> Target Accuracy factor. If omitted, Z_STEPPER_ALIGN_ACC.
* A<amplification> Provide an Amplification value. If omitted, Z_STEPPER_ALIGN_AMP.
* R Flag to recalculate points based on current probe offsets
*/
void GcodeSuite::G34() {
DEBUG_SECTION(log_G34, "G34", DEBUGGING(LEVELING));
if (DEBUGGING(LEVELING)) log_machine_info();
do { // break out on error
#if NUM_Z_STEPPER_DRIVERS == 4
SERIAL_ECHOLNPGM("Alignment for 4 steppers is Experimental!");
#elif NUM_Z_STEPPER_DRIVERS > 4
SERIAL_ECHOLNPGM("Alignment not supported for over 4 steppers");
break;
#endif
const int8_t z_auto_align_iterations = parser.intval('I', Z_STEPPER_ALIGN_ITERATIONS);
if (!WITHIN(z_auto_align_iterations, 1, 30)) {
SERIAL_ECHOLNPGM("?(I)teration out of bounds (1-30).");
break;
planner.synchronize(); // Prevent damage
const bool seenL = parser.seen('L');
if (seenL) stepper.set_all_z_lock(false);
const bool seenZ = parser.seenval('Z');
if (seenZ) {
const bool state = parser.boolval('S', true);
switch (parser.intval('Z')) {
case 1: stepper.set_z1_lock(state); break;
case 2: stepper.set_z2_lock(state); break;
#if NUM_Z_STEPPER_DRIVERS >= 3
case 3: stepper.set_z3_lock(state); break;
#if NUM_Z_STEPPER_DRIVERS >= 4
case 4: stepper.set_z4_lock(state); break;
#endif
#endif
}
}
const float z_auto_align_accuracy = parser.floatval('T', Z_STEPPER_ALIGN_ACC);
if (!WITHIN(z_auto_align_accuracy, 0.01f, 1.0f)) {
SERIAL_ECHOLNPGM("?(T)arget accuracy out of bounds (0.01-1.0).");
break;
}
if (seenL || seenZ) {
stepper.set_separate_multi_axis(seenZ);
return;
}
const float z_auto_align_amplification =
#if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
Z_STEPPER_ALIGN_AMP;
#else
parser.floatval('A', Z_STEPPER_ALIGN_AMP);
if (!WITHIN(ABS(z_auto_align_amplification), 0.5f, 2.0f)) {
SERIAL_ECHOLNPGM("?(A)mplification out of bounds (0.5-2.0).");
break;
}
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
do { // break out on error
#if NUM_Z_STEPPER_DRIVERS == 4
SERIAL_ECHOLNPGM("Alignment for 4 steppers is Experimental!");
#elif NUM_Z_STEPPER_DRIVERS > 4
SERIAL_ECHOLNPGM("Alignment not supported for over 4 steppers");
break;
#endif
if (parser.seen('R')) z_stepper_align.reset_to_default();
const int8_t z_auto_align_iterations = parser.intval('I', Z_STEPPER_ALIGN_ITERATIONS);
if (!WITHIN(z_auto_align_iterations, 1, 30)) {
SERIAL_ECHOLNPGM("?(I)teration out of bounds (1-30).");
break;
}
const ProbePtRaise raise_after = parser.boolval('E') ? PROBE_PT_STOW : PROBE_PT_RAISE;
const float z_auto_align_accuracy = parser.floatval('T', Z_STEPPER_ALIGN_ACC);
if (!WITHIN(z_auto_align_accuracy, 0.01f, 1.0f)) {
SERIAL_ECHOLNPGM("?(T)arget accuracy out of bounds (0.01-1.0).");
break;
}
// Wait for planner moves to finish!
planner.synchronize();
const float z_auto_align_amplification = TERN(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS, Z_STEPPER_ALIGN_AMP, parser.floatval('A', Z_STEPPER_ALIGN_AMP));
if (!WITHIN(ABS(z_auto_align_amplification), 0.5f, 2.0f)) {
SERIAL_ECHOLNPGM("?(A)mplification out of bounds (0.5-2.0).");
break;
}
// Disable the leveling matrix before auto-aligning
#if HAS_LEVELING
TERN_(RESTORE_LEVELING_AFTER_G34, const bool leveling_was_active = planner.leveling_active);
set_bed_leveling_enabled(false);
#endif
if (parser.seen('R')) z_stepper_align.reset_to_default();
TERN_(CNC_WORKSPACE_PLANES, workspace_plane = PLANE_XY);
const ProbePtRaise raise_after = parser.boolval('E') ? PROBE_PT_STOW : PROBE_PT_RAISE;
// Always home with tool 0 active
#if HAS_MULTI_HOTEND
const uint8_t old_tool_index = active_extruder;
tool_change(0, true);
#endif
// Disable the leveling matrix before auto-aligning
#if HAS_LEVELING
TERN_(RESTORE_LEVELING_AFTER_G34, const bool leveling_was_active = planner.leveling_active);
set_bed_leveling_enabled(false);
#endif
TERN_(HAS_DUPLICATION_MODE, set_duplication_enabled(false));
// In BLTOUCH HS mode, the probe travels in a deployed state.
// Users of G34 might have a badly misaligned bed, so raise Z by the
// length of the deployed pin (BLTOUCH stroke < 7mm)
#define Z_BASIC_CLEARANCE (Z_CLEARANCE_BETWEEN_PROBES + 7.0f * BOTH(BLTOUCH, BLTOUCH_HS_MODE))
// Compute a worst-case clearance height to probe from. After the first
// iteration this will be re-calculated based on the actual bed position
auto magnitude2 = [&](const uint8_t i, const uint8_t j) {
const xy_pos_t diff = z_stepper_align.xy[i] - z_stepper_align.xy[j];
return HYPOT2(diff.x, diff.y);
};
float z_probe = Z_BASIC_CLEARANCE + (G34_MAX_GRADE) * 0.01f * SQRT(
#if NUM_Z_STEPPER_DRIVERS == 3
_MAX(magnitude2(0, 1), magnitude2(1, 2), magnitude2(2, 0))
#elif NUM_Z_STEPPER_DRIVERS == 4
_MAX(magnitude2(0, 1), magnitude2(1, 2), magnitude2(2, 3),
magnitude2(3, 0), magnitude2(0, 2), magnitude2(1, 3))
#else
magnitude2(0, 1)
TERN_(CNC_WORKSPACE_PLANES, workspace_plane = PLANE_XY);
// Always home with tool 0 active
#if HAS_MULTI_HOTEND
const uint8_t old_tool_index = active_extruder;
tool_change(0, true);
#endif
);
// Home before the alignment procedure
if (!all_axes_known()) home_all_axes();
TERN_(HAS_DUPLICATION_MODE, set_duplication_enabled(false));
// Move the Z coordinate realm towards the positive - dirty trick
current_position.z += z_probe * 0.5f;
sync_plan_position();
// Now, the Z origin lies below the build plate. That allows to probe deeper, before run_z_probe throws an error.
// This hack is un-done at the end of G34 - either by re-homing, or by using the probed heights of the last iteration.
// In BLTOUCH HS mode, the probe travels in a deployed state.
// Users of G34 might have a badly misaligned bed, so raise Z by the
// length of the deployed pin (BLTOUCH stroke < 7mm)
#define Z_BASIC_CLEARANCE (Z_CLEARANCE_BETWEEN_PROBES + 7.0f * BOTH(BLTOUCH, BLTOUCH_HS_MODE))
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
float last_z_align_move[NUM_Z_STEPPER_DRIVERS] = ARRAY_N(NUM_Z_STEPPER_DRIVERS, 10000.0f, 10000.0f, 10000.0f, 10000.0f);
#else
float last_z_align_level_indicator = 10000.0f;
#endif
float z_measured[NUM_Z_STEPPER_DRIVERS] = { 0 },
z_maxdiff = 0.0f,
amplification = z_auto_align_amplification;
// Compute a worst-case clearance height to probe from. After the first
// iteration this will be re-calculated based on the actual bed position
auto magnitude2 = [&](const uint8_t i, const uint8_t j) {
const xy_pos_t diff = z_stepper_align.xy[i] - z_stepper_align.xy[j];
return HYPOT2(diff.x, diff.y);
};
float z_probe = Z_BASIC_CLEARANCE + (G34_MAX_GRADE) * 0.01f * SQRT(
#if NUM_Z_STEPPER_DRIVERS == 3
_MAX(magnitude2(0, 1), magnitude2(1, 2), magnitude2(2, 0))
#elif NUM_Z_STEPPER_DRIVERS == 4
_MAX(magnitude2(0, 1), magnitude2(1, 2), magnitude2(2, 3),
magnitude2(3, 0), magnitude2(0, 2), magnitude2(1, 3))
#else
magnitude2(0, 1)
#endif
);
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
bool adjustment_reverse = false;
#endif
// Home before the alignment procedure
if (!all_axes_known()) home_all_axes();
#if HAS_DISPLAY
PGM_P const msg_iteration = GET_TEXT(MSG_ITERATION);
const uint8_t iter_str_len = strlen_P(msg_iteration);
#endif
// Move the Z coordinate realm towards the positive - dirty trick
current_position.z += z_probe * 0.5f;
sync_plan_position();
// Now, the Z origin lies below the build plate. That allows to probe deeper, before run_z_probe throws an error.
// This hack is un-done at the end of G34 - either by re-homing, or by using the probed heights of the last iteration.
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
float last_z_align_move[NUM_Z_STEPPER_DRIVERS] = ARRAY_N(NUM_Z_STEPPER_DRIVERS, 10000.0f, 10000.0f, 10000.0f, 10000.0f);
#else
float last_z_align_level_indicator = 10000.0f;
#endif
float z_measured[NUM_Z_STEPPER_DRIVERS] = { 0 },
z_maxdiff = 0.0f,
amplification = z_auto_align_amplification;
// Final z and iteration values will be used after breaking the loop
float z_measured_min;
uint8_t iteration = 0;
bool err_break = false; // To break out of nested loops
while (iteration < z_auto_align_iterations) {
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> probing all positions.");
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
bool adjustment_reverse = false;
#endif
const int iter = iteration + 1;
SERIAL_ECHOLNPAIR("\nG34 Iteration: ", iter);
#if HAS_DISPLAY
char str[iter_str_len + 2 + 1];
sprintf_P(str, msg_iteration, iter);
ui.set_status(str);
PGM_P const msg_iteration = GET_TEXT(MSG_ITERATION);
const uint8_t iter_str_len = strlen_P(msg_iteration);
#endif
// Initialize minimum value
z_measured_min = 100000.0f;
float z_measured_max = -100000.0f;
// Probe all positions (one per Z-Stepper)
LOOP_L_N(i, NUM_Z_STEPPER_DRIVERS) {
// iteration odd/even --> downward / upward stepper sequence
const uint8_t iprobe = (iteration & 1) ? NUM_Z_STEPPER_DRIVERS - 1 - i : i;
// Safe clearance even on an incline
if ((iteration == 0 || i > 0) && z_probe > current_position.z) do_blocking_move_to_z(z_probe);
if (DEBUGGING(LEVELING))
DEBUG_ECHOLNPAIR_P(PSTR("Probing X"), z_stepper_align.xy[iprobe].x, SP_Y_STR, z_stepper_align.xy[iprobe].y);
// Probe a Z height for each stepper.
// Probing sanity check is disabled, as it would trigger even in normal cases because
// current_position.z has been manually altered in the "dirty trick" above.
const float z_probed_height = probe.probe_at_point(z_stepper_align.xy[iprobe], raise_after, 0, true, false);
if (isnan(z_probed_height)) {
SERIAL_ECHOLNPGM("Probing failed");
LCD_MESSAGEPGM(MSG_LCD_PROBING_FAILED);
err_break = true;
break;
}
// Final z and iteration values will be used after breaking the loop
float z_measured_min;
uint8_t iteration = 0;
bool err_break = false; // To break out of nested loops
while (iteration < z_auto_align_iterations) {
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("> probing all positions.");
const int iter = iteration + 1;
SERIAL_ECHOLNPAIR("\nG34 Iteration: ", iter);
#if HAS_DISPLAY
char str[iter_str_len + 2 + 1];
sprintf_P(str, msg_iteration, iter);
ui.set_status(str);
#endif
// Add height to each value, to provide a more useful target height for
// the next iteration of probing. This allows adjustments to be made away from the bed.
z_measured[iprobe] = z_probed_height + Z_CLEARANCE_BETWEEN_PROBES;
// Initialize minimum value
z_measured_min = 100000.0f;
float z_measured_max = -100000.0f;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(iprobe + 1), " measured position is ", z_measured[iprobe]);
// Probe all positions (one per Z-Stepper)
LOOP_L_N(i, NUM_Z_STEPPER_DRIVERS) {
// iteration odd/even --> downward / upward stepper sequence
const uint8_t iprobe = (iteration & 1) ? NUM_Z_STEPPER_DRIVERS - 1 - i : i;
// Safe clearance even on an incline
if ((iteration == 0 || i > 0) && z_probe > current_position.z) do_blocking_move_to_z(z_probe);
if (DEBUGGING(LEVELING))
DEBUG_ECHOLNPAIR_P(PSTR("Probing X"), z_stepper_align.xy[iprobe].x, SP_Y_STR, z_stepper_align.xy[iprobe].y);
// Probe a Z height for each stepper.
// Probing sanity check is disabled, as it would trigger even in normal cases because
// current_position.z has been manually altered in the "dirty trick" above.
const float z_probed_height = probe.probe_at_point(z_stepper_align.xy[iprobe], raise_after, 0, true, false);
if (isnan(z_probed_height)) {
SERIAL_ECHOLNPGM("Probing failed");
LCD_MESSAGEPGM(MSG_LCD_PROBING_FAILED);
err_break = true;
break;
}
// Remember the minimum measurement to calculate the correction later on
z_measured_min = _MIN(z_measured_min, z_measured[iprobe]);
z_measured_max = _MAX(z_measured_max, z_measured[iprobe]);
} // for (i)
// Add height to each value, to provide a more useful target height for
// the next iteration of probing. This allows adjustments to be made away from the bed.
z_measured[iprobe] = z_probed_height + Z_CLEARANCE_BETWEEN_PROBES;
if (err_break) break;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(iprobe + 1), " measured position is ", z_measured[iprobe]);
// Adapt the next probe clearance height based on the new measurements.
// Safe_height = lowest distance to bed (= highest measurement) plus highest measured misalignment.
z_maxdiff = z_measured_max - z_measured_min;
z_probe = Z_BASIC_CLEARANCE + z_measured_max + z_maxdiff;
// Remember the minimum measurement to calculate the correction later on
z_measured_min = _MIN(z_measured_min, z_measured[iprobe]);
z_measured_max = _MAX(z_measured_max, z_measured[iprobe]);
} // for (i)
#if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Replace the initial values in z_measured with calculated heights at
// each stepper position. This allows the adjustment algorithm to be
// shared between both possible probing mechanisms.
// This must be done after the next z_probe height is calculated, so that
// the height is calculated from actual print area positions, and not
// extrapolated motor movements.
// Compute the least-squares fit for all probed points.
// Calculate the Z position of each stepper and store it in z_measured.
// This allows the actual adjustment logic to be shared by both algorithms.
linear_fit_data lfd;
incremental_LSF_reset(&lfd);
LOOP_L_N(i, NUM_Z_STEPPER_DRIVERS) {
SERIAL_ECHOLNPAIR("PROBEPT_", int(i), ": ", z_measured[i]);
incremental_LSF(&lfd, z_stepper_align.xy[i], z_measured[i]);
}
finish_incremental_LSF(&lfd);
if (err_break) break;
z_measured_min = 100000.0f;
LOOP_L_N(i, NUM_Z_STEPPER_DRIVERS) {
z_measured[i] = -(lfd.A * z_stepper_align.stepper_xy[i].x + lfd.B * z_stepper_align.stepper_xy[i].y + lfd.D);
z_measured_min = _MIN(z_measured_min, z_measured[i]);
}
// Adapt the next probe clearance height based on the new measurements.
// Safe_height = lowest distance to bed (= highest measurement) plus highest measured misalignment.
z_maxdiff = z_measured_max - z_measured_min;
z_probe = Z_BASIC_CLEARANCE + z_measured_max + z_maxdiff;
#if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Replace the initial values in z_measured with calculated heights at
// each stepper position. This allows the adjustment algorithm to be
// shared between both possible probing mechanisms.
// This must be done after the next z_probe height is calculated, so that
// the height is calculated from actual print area positions, and not
// extrapolated motor movements.
// Compute the least-squares fit for all probed points.
// Calculate the Z position of each stepper and store it in z_measured.
// This allows the actual adjustment logic to be shared by both algorithms.
linear_fit_data lfd;
incremental_LSF_reset(&lfd);
LOOP_L_N(i, NUM_Z_STEPPER_DRIVERS) {
SERIAL_ECHOLNPAIR("PROBEPT_", int(i), ": ", z_measured[i]);
incremental_LSF(&lfd, z_stepper_align.xy[i], z_measured[i]);
}
finish_incremental_LSF(&lfd);
SERIAL_ECHOLNPAIR("CALCULATED STEPPER POSITIONS: Z1=", z_measured[0], " Z2=", z_measured[1], " Z3=", z_measured[2]);
#endif
z_measured_min = 100000.0f;
LOOP_L_N(i, NUM_Z_STEPPER_DRIVERS) {
z_measured[i] = -(lfd.A * z_stepper_align.stepper_xy[i].x + lfd.B * z_stepper_align.stepper_xy[i].y + lfd.D);
z_measured_min = _MIN(z_measured_min, z_measured[i]);
}
SERIAL_ECHOLNPAIR("\n"
"DIFFERENCE Z1-Z2=", ABS(z_measured[0] - z_measured[1])
#if NUM_Z_STEPPER_DRIVERS == 3
, " Z2-Z3=", ABS(z_measured[1] - z_measured[2])
, " Z3-Z1=", ABS(z_measured[2] - z_measured[0])
#endif
);
#if HAS_DISPLAY
char fstr1[10];
#if NUM_Z_STEPPER_DRIVERS == 2
char msg[6 + (6 + 5) * 1 + 1];
#else
char msg[6 + (6 + 5) * 3 + 1], fstr2[10], fstr3[10];
SERIAL_ECHOLNPAIR("CALCULATED STEPPER POSITIONS: Z1=", z_measured[0], " Z2=", z_measured[1], " Z3=", z_measured[2]);
#endif
sprintf_P(msg,
PSTR("Diffs Z1-Z2=%s"
#if NUM_Z_STEPPER_DRIVERS == 3
" Z2-Z3=%s"
" Z3-Z1=%s"
#endif
), dtostrf(ABS(z_measured[0] - z_measured[1]), 1, 3, fstr1)
SERIAL_ECHOLNPAIR("\n"
"DIFFERENCE Z1-Z2=", ABS(z_measured[0] - z_measured[1])
#if NUM_Z_STEPPER_DRIVERS == 3
, dtostrf(ABS(z_measured[1] - z_measured[2]), 1, 3, fstr2)
, dtostrf(ABS(z_measured[2] - z_measured[0]), 1, 3, fstr3)
, " Z2-Z3=", ABS(z_measured[1] - z_measured[2])
, " Z3-Z1=", ABS(z_measured[2] - z_measured[0])
#endif
);
ui.set_status(msg);
#endif
#if HAS_DISPLAY
char fstr1[10];
#if NUM_Z_STEPPER_DRIVERS == 2
char msg[6 + (6 + 5) * 1 + 1];
#else
char msg[6 + (6 + 5) * 3 + 1], fstr2[10], fstr3[10];
#endif
sprintf_P(msg,
PSTR("Diffs Z1-Z2=%s"
#if NUM_Z_STEPPER_DRIVERS == 3
" Z2-Z3=%s"
" Z3-Z1=%s"
#endif
), dtostrf(ABS(z_measured[0] - z_measured[1]), 1, 3, fstr1)
#if NUM_Z_STEPPER_DRIVERS == 3
, dtostrf(ABS(z_measured[1] - z_measured[2]), 1, 3, fstr2)
, dtostrf(ABS(z_measured[2] - z_measured[0]), 1, 3, fstr3)
#endif
);
ui.set_status(msg);
#endif
auto decreasing_accuracy = [](const float &v1, const float &v2){
if (v1 < v2 * 0.7f) {
SERIAL_ECHOLNPGM("Decreasing Accuracy Detected.");
LCD_MESSAGEPGM(MSG_DECREASING_ACCURACY);
return true;
}
return false;
};
auto decreasing_accuracy = [](const float &v1, const float &v2){
if (v1 < v2 * 0.7f) {
SERIAL_ECHOLNPGM("Decreasing Accuracy Detected.");
LCD_MESSAGEPGM(MSG_DECREASING_ACCURACY);
return true;
}
return false;
};
#if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
#if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Check if the applied corrections go in the correct direction.
// Calculate the sum of the absolute deviations from the mean of the probe measurements.
// Compare to the last iteration to ensure it's getting better.
// Check if the applied corrections go in the correct direction.
// Calculate the sum of the absolute deviations from the mean of the probe measurements.
// Compare to the last iteration to ensure it's getting better.
// Calculate mean value as a reference
float z_measured_mean = 0.0f;
LOOP_L_N(zstepper, NUM_Z_STEPPER_DRIVERS) z_measured_mean += z_measured[zstepper];
z_measured_mean /= NUM_Z_STEPPER_DRIVERS;
// Calculate mean value as a reference
float z_measured_mean = 0.0f;
LOOP_L_N(zstepper, NUM_Z_STEPPER_DRIVERS) z_measured_mean += z_measured[zstepper];
z_measured_mean /= NUM_Z_STEPPER_DRIVERS;
// Calculate the sum of the absolute deviations from the mean value
float z_align_level_indicator = 0.0f;
LOOP_L_N(zstepper, NUM_Z_STEPPER_DRIVERS)
z_align_level_indicator += ABS(z_measured[zstepper] - z_measured_mean);
// Calculate the sum of the absolute deviations from the mean value
float z_align_level_indicator = 0.0f;
LOOP_L_N(zstepper, NUM_Z_STEPPER_DRIVERS)
z_align_level_indicator += ABS(z_measured[zstepper] - z_measured_mean);
// If it's getting worse, stop and throw an error
err_break = decreasing_accuracy(last_z_align_level_indicator, z_align_level_indicator);
if (err_break) break;
// If it's getting worse, stop and throw an error
err_break = decreasing_accuracy(last_z_align_level_indicator, z_align_level_indicator);
if (err_break) break;
last_z_align_level_indicator = z_align_level_indicator;
#endif
last_z_align_level_indicator = z_align_level_indicator;
#endif
// The following correction actions are to be enabled for select Z-steppers only
stepper.set_separate_multi_axis(true);
bool success_break = true;
// Correct the individual stepper offsets
LOOP_L_N(zstepper, NUM_Z_STEPPER_DRIVERS) {
// Calculate current stepper move
float z_align_move = z_measured[zstepper] - z_measured_min;
const float z_align_abs = ABS(z_align_move);
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Optimize one iteration's correction based on the first measurements
if (z_align_abs) amplification = (iteration == 1) ? _MIN(last_z_align_move[zstepper] / z_align_abs, 2.0f) : z_auto_align_amplification;
// Check for less accuracy compared to last move
if (decreasing_accuracy(last_z_align_move[zstepper], z_align_abs)) {
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " last_z_align_move = ", last_z_align_move[zstepper]);
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " z_align_abs = ", z_align_abs);
adjustment_reverse = !adjustment_reverse;
}
// The following correction actions are to be enabled for select Z-steppers only
stepper.set_separate_multi_axis(true);
bool success_break = true;
// Correct the individual stepper offsets
LOOP_L_N(zstepper, NUM_Z_STEPPER_DRIVERS) {
// Calculate current stepper move
float z_align_move = z_measured[zstepper] - z_measured_min;
const float z_align_abs = ABS(z_align_move);
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Optimize one iteration's correction based on the first measurements
if (z_align_abs) amplification = (iteration == 1) ? _MIN(last_z_align_move[zstepper] / z_align_abs, 2.0f) : z_auto_align_amplification;
// Check for less accuracy compared to last move
if (decreasing_accuracy(last_z_align_move[zstepper], z_align_abs)) {
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " last_z_align_move = ", last_z_align_move[zstepper]);
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " z_align_abs = ", z_align_abs);
adjustment_reverse = !adjustment_reverse;
}
// Remember the alignment for the next iteration, but only if steppers move,
// otherwise it would be just zero (in case this stepper was at z_measured_min already)
if (z_align_abs > 0) last_z_align_move[zstepper] = z_align_abs;
#endif
// Remember the alignment for the next iteration, but only if steppers move,
// otherwise it would be just zero (in case this stepper was at z_measured_min already)
if (z_align_abs > 0) last_z_align_move[zstepper] = z_align_abs;
#endif
// Stop early if all measured points achieve accuracy target
if (z_align_abs > z_auto_align_accuracy) success_break = false;
// Stop early if all measured points achieve accuracy target
if (z_align_abs > z_auto_align_accuracy) success_break = false;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " corrected by ", z_align_move);
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " corrected by ", z_align_move);
// Lock all steppers except one
stepper.set_all_z_lock(true, zstepper);
// Lock all steppers except one
stepper.set_all_z_lock(true, zstepper);
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Decreasing accuracy was detected so move was inverted.
// Will match reversed Z steppers on dual steppers. Triple will need more work to map.
if (adjustment_reverse) {
z_align_move = -z_align_move;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " correction reversed to ", z_align_move);
}
#endif
#if DISABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
// Decreasing accuracy was detected so move was inverted.
// Will match reversed Z steppers on dual steppers. Triple will need more work to map.
if (adjustment_reverse) {
z_align_move = -z_align_move;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " correction reversed to ", z_align_move);
}
#endif
// Do a move to correct part of the misalignment for the current stepper
do_blocking_move_to_z(amplification * z_align_move + current_position.z);
} // for (zstepper)
// Do a move to correct part of the misalignment for the current stepper
do_blocking_move_to_z(amplification * z_align_move + current_position.z);
} // for (zstepper)
// Back to normal stepper operations
stepper.set_all_z_lock(false);
stepper.set_separate_multi_axis(false);
// Back to normal stepper operations
stepper.set_all_z_lock(false);
stepper.set_separate_multi_axis(false);
if (err_break) break;
if (err_break) break;
if (success_break) {
SERIAL_ECHOLNPGM("Target accuracy achieved.");
LCD_MESSAGEPGM(MSG_ACCURACY_ACHIEVED);
break;
}
if (success_break) {
SERIAL_ECHOLNPGM("Target accuracy achieved.");
LCD_MESSAGEPGM(MSG_ACCURACY_ACHIEVED);
break;
}
iteration++;
} // while (iteration < z_auto_align_iterations)
iteration++;
} // while (iteration < z_auto_align_iterations)
if (err_break)
SERIAL_ECHOLNPGM("G34 aborted.");
else {
SERIAL_ECHOLNPAIR("Did ", int(iteration + (iteration != z_auto_align_iterations)), " of ", int(z_auto_align_iterations));
SERIAL_ECHOLNPAIR_F("Accuracy: ", z_maxdiff);
}
if (err_break)
SERIAL_ECHOLNPGM("G34 aborted.");
else {
SERIAL_ECHOLNPAIR("Did ", int(iteration + (iteration != z_auto_align_iterations)), " of ", int(z_auto_align_iterations));
SERIAL_ECHOLNPAIR_F("Accuracy: ", z_maxdiff);
}
// Stow the probe, as the last call to probe.probe_at_point(...) left
// the probe deployed if it was successful.
probe.stow();
// Stow the probe, as the last call to probe.probe_at_point(...) left
// the probe deployed if it was successful.
probe.stow();
#if ENABLED(HOME_AFTER_G34)
// After this operation the z position needs correction
set_axis_never_homed(Z_AXIS);
// Home Z after the alignment procedure
process_subcommands_now_P(PSTR("G28Z"));
#else
// Use the probed height from the last iteration to determine the Z height.
// z_measured_min is used, because all steppers are aligned to z_measured_min.
// Ideally, this would be equal to the 'z_probe * 0.5f' which was added earlier.
current_position.z -= z_measured_min - (float)Z_CLEARANCE_BETWEEN_PROBES;
sync_plan_position();
#endif
#if ENABLED(HOME_AFTER_G34)
// After this operation the z position needs correction
set_axis_never_homed(Z_AXIS);
// Home Z after the alignment procedure
process_subcommands_now_P(PSTR("G28Z"));
#else
// Use the probed height from the last iteration to determine the Z height.
// z_measured_min is used, because all steppers are aligned to z_measured_min.
// Ideally, this would be equal to the 'z_probe * 0.5f' which was added earlier.
current_position.z -= z_measured_min - (float)Z_CLEARANCE_BETWEEN_PROBES;
sync_plan_position();
#endif
// Restore the active tool after homing
TERN_(HAS_MULTI_HOTEND, tool_change(old_tool_index, DISABLED(PARKING_EXTRUDER))); // Fetch previous tool for parking extruder
// Restore the active tool after homing
TERN_(HAS_MULTI_HOTEND, tool_change(old_tool_index, DISABLED(PARKING_EXTRUDER))); // Fetch previous tool for parking extruder
#if BOTH(HAS_LEVELING, RESTORE_LEVELING_AFTER_G34)
set_bed_leveling_enabled(leveling_was_active);
#endif
#if BOTH(HAS_LEVELING, RESTORE_LEVELING_AFTER_G34)
set_bed_leveling_enabled(leveling_was_active);
#endif
}while(0);
}while(0);
#endif
}
#endif // Z_MULTI_ENDSTOPS || Z_STEPPER_AUTO_ALIGN
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
/**
* M422: Set a Z-Stepper automatic alignment XY point.
* Use repeatedly to set multiple points.

2
Marlin/src/gcode/gcode.cpp
View File

@ -327,7 +327,7 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
case 33: G33(); break; // G33: Delta Auto-Calibration
#endif
#if EITHER(Z_STEPPER_AUTO_ALIGN, MECHANICAL_GANTRY_CALIBRATION)
#if ANY(Z_MULTI_ENDSTOPS, Z_STEPPER_AUTO_ALIGN, MECHANICAL_GANTRY_CALIBRATION)
case 34: G34(); break; // G34: Z Stepper automatic alignment using probe
#endif

2
Marlin/src/gcode/gcode.h
View File

@ -468,7 +468,7 @@ private:
TERN_(DELTA_AUTO_CALIBRATION, static void G33());
#if EITHER(Z_STEPPER_AUTO_ALIGN, MECHANICAL_GANTRY_CALIBRATION)
#if ANY(Z_MULTI_ENDSTOPS, Z_STEPPER_AUTO_ALIGN, MECHANICAL_GANTRY_CALIBRATION)
static void G34();
#endif

7
Marlin/src/inc/SanityCheck.h
View File

@ -2792,8 +2792,11 @@ static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
#error "Z_STEPPER_AUTO_ALIGN requires NUM_Z_STEPPER_DRIVERS greater than 1."
#elif !HAS_BED_PROBE
#error "Z_STEPPER_AUTO_ALIGN requires a Z-bed probe."
#elif ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS) && NUM_Z_STEPPER_DRIVERS < 3
#error "Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS requires NUM_Z_STEPPER_DRIVERS to be 3 or 4."
#elif ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
static_assert(WITHIN(Z_STEPPER_ALIGN_AMP, 0.5, 2.0), "Z_STEPPER_ALIGN_AMP must be between 0.5 and 2.0.");
#if NUM_Z_STEPPER_DRIVERS < 3
#error "Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS requires NUM_Z_STEPPER_DRIVERS to be 3 or 4."
#endif
#endif
#endif

1
platformio.ini
View File

@ -316,6 +316,7 @@ EXT_SOLENOID|MANUAL_SOLENOID_CONTROL = src_filter=+<src/feature/solenoid.cpp> +<
HAS_CUTTER = src_filter=+<src/feature/spindle_laser.cpp> +<src/gcode/control/M3-M5.cpp>
EXPERIMENTAL_I2CBUS = src_filter=+<src/feature/twibus.cpp> +<src/gcode/feature/i2c>
MECHANICAL_GANTRY_CAL.+ = src_filter=+<src/gcode/calibrate/G34.cpp>
Z_MULTI_ENDSTOPS = src_filter=+<src/gcode/calibrate/G34_M422.cpp>
Z_STEPPER_AUTO_ALIGN = src_filter=+<src/feature/z_stepper_align.cpp> +<src/gcode/calibrate/G34_M422.cpp>
G26_MESH_VALIDATION = src_filter=+<src/gcode/bedlevel/G26.cpp>
ASSISTED_TRAMMING = src_filter=+<src/gcode/bedlevel/G35.cpp>

Write Preview
Loading…
Cancel
Save