diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 0f9ebe2a5a..de2b10ba37 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -6686,6 +6686,35 @@ inline void gcode_T(uint8_t tmp_extruder) {
         }
         // No extra case for AUTO_BED_LEVELING_FEATURE in DUAL_X_CARRIAGE. Does that mean they don't work together?
       #else // !DUAL_X_CARRIAGE
+
+        //
+        // Set current_position to the position of the new nozzle.
+        // Offsets are based on linear distance, so we need to get
+        // the resulting position in coordinate space.
+        //
+        // - With grid or 3-point leveling, offset XYZ by a tilted vector
+        // - With mesh leveling, update Z for the new position
+        // - Otherwise, just use the raw linear distance
+        //
+        // Software endstops are altered here too. Consider a case where:
+        //   E0 at X=0 ... E1 at X=10
+        // When we switch to E1 now X=10, but E1 can't move left.
+        // To express this we apply the change in XY to the software endstops.
+        // E1 can move farther right than E0, so the right limit is extended.
+        //
+        // Note that we don't adjust the Z software endstops. Why not?
+        // Consider a case where Z=0 (here) and switching to E1 makes Z=1
+        // because the bed is 1mm lower at the new position. As long as
+        // the first nozzle is out of the way, the carriage should be
+        // allowed to move 1mm lower. This technically "breaks" the
+        // Z software endstop. But this is technically correct (and
+        // there is no viable alternative).
+        //
+        float xydiff[2] = {
+          hotend_offset[X_AXIS][tmp_extruder] - hotend_offset[X_AXIS][active_extruder],
+          hotend_offset[Y_AXIS][tmp_extruder] - hotend_offset[Y_AXIS][active_extruder]
+        };
+
         #if ENABLED(AUTO_BED_LEVELING_FEATURE)
           // Offset extruder, make sure to apply the bed level rotation matrix
           vector_3 tmp_offset_vec = vector_3(hotend_offset[X_AXIS][tmp_extruder],
@@ -6721,17 +6750,26 @@ inline void gcode_T(uint8_t tmp_extruder) {
             }
           #endif
 
-        #else // !AUTO_BED_LEVELING_FEATURE
+        #elif ENABLED(MESH_BED_LEVELING)
 
-          // The newly-selected extruder is actually at...
-          for (int i=X_AXIS; i<=Y_AXIS; i++) {
-            float diff = hotend_offset[i][tmp_extruder] - hotend_offset[i][active_extruder];
-            current_position[i] += diff;
-            position_shift[i] += diff; // Offset the coordinate space
-            update_software_endstops((AxisEnum)i);
+          if (mbl.active()) {
+            float xpos = current_position[X_AXIS] - home_offset[X_AXIS],
+                  ypos = current_position[Y_AXIS] - home_offset[Y_AXIS];
+            current_position[Z_AXIS] += mbl.get_z(xpos + xydiff[X_AXIS], ypos + xydiff[Y_AXIS]) - mbl.get_z(xpos, ypos);
           }
 
-        #endif // !AUTO_BED_LEVELING_FEATURE
+        #else // no bed leveling
+
+          // The newly-selected extruder XY is actually at...
+          current_position[X_AXIS] += xydiff[X_AXIS];
+          current_position[Y_AXIS] += xydiff[Y_AXIS];
+
+        #endif // no bed leveling
+
+        for (uint8_t i = X_AXIS; i <= Y_AXIS; i++) {
+          position_shift[i] += xydiff[i];
+          update_software_endstops((AxisEnum)i);
+        }
 
         // Set the new active extruder
         active_extruder = tmp_extruder;