Scott Lahteine
8 years ago
committed by
GitHub
GitHub
5 changed files with 213 additions and 13 deletions
@ -0,0 +1,205 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
|
|||
/**
|
|||
* Mightyboard Rev.E pin assignments |
|||
*/ |
|||
|
|||
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) |
|||
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." |
|||
#endif |
|||
|
|||
#define DEFAULT_MACHINE_NAME "MB Replicator" |
|||
#define BOARD_NAME "Mightyboard" |
|||
|
|||
#define LARGE_FLASH true |
|||
|
|||
//
|
|||
// Servos
|
|||
//
|
|||
#define SERVO0_PIN 36 // C1 (1280-EX1)
|
|||
#define SERVO1_PIN 37 // C0 (1280-EX2)
|
|||
#define SERVO2_PIN 40 // G1 (1280-EX3)
|
|||
#define SERVO3_PIN 41 // G0 (1280-EX4)
|
|||
|
|||
//
|
|||
// Limit Switches
|
|||
//
|
|||
#define X_MIN_PIN 49 // L0
|
|||
#define X_MAX_PIN 48 // L1
|
|||
#define Y_MIN_PIN 47 // L2
|
|||
#define Y_MAX_PIN 46 // L3
|
|||
#define Z_MIN_PIN 43 // L6
|
|||
#define Z_MAX_PIN 42 // L7
|
|||
|
|||
//
|
|||
// Z Probe (when not Z_MIN_PIN)
|
|||
//
|
|||
#ifndef Z_MIN_PROBE_PIN |
|||
#define Z_MIN_PROBE_PIN 42 |
|||
#endif |
|||
|
|||
//
|
|||
// Steppers
|
|||
//
|
|||
#define X_STEP_PIN 55 // F1
|
|||
#define X_DIR_PIN 54 // F0
|
|||
#define X_ENABLE_PIN 56 // F2
|
|||
|
|||
#define Y_STEP_PIN 59 // F5
|
|||
#define Y_DIR_PIN 58 // F4
|
|||
#define Y_ENABLE_PIN 60 // F6
|
|||
|
|||
#define Z_STEP_PIN 63 // K1
|
|||
#define Z_DIR_PIN 62 // K0
|
|||
#define Z_ENABLE_PIN 64 // K2
|
|||
|
|||
#define E0_STEP_PIN 25 // A3
|
|||
#define E0_DIR_PIN 24 // A2
|
|||
#define E0_ENABLE_PIN 26 // A4
|
|||
|
|||
#define E1_STEP_PIN 29 // A7
|
|||
#define E1_DIR_PIN 28 // A6
|
|||
#define E1_ENABLE_PIN 39 // G2
|
|||
|
|||
//
|
|||
// I2C Digipots - MCP4018
|
|||
// Address 5E (2F << 1)
|
|||
// Set from 0 - 127 with stop bit.
|
|||
// (Ex. 3F << 1 | 1)
|
|||
//
|
|||
#define DIGIPOTS_I2C_SCL 76 // J5
|
|||
#define DIGIPOTS_I2C_SDA_X 57 // F3
|
|||
#define DIGIPOTS_I2C_SDA_Y 61 // F7
|
|||
#define DIGIPOTS_I2C_SDA_Z 65 // K3
|
|||
#define DIGIPOTS_I2C_SDA_E0 27 // A5
|
|||
#define DIGIPOTS_I2C_SDA_E1 77 // J6
|
|||
|
|||
//
|
|||
// Temperature Sensors
|
|||
//
|
|||
#define TEMP_BED_PIN 69 // K7
|
|||
|
|||
// SPI for Max6675 or Max31855 Thermocouple
|
|||
// Uses a separate SPI bus
|
|||
//
|
|||
// 3 E5 DO (SO)
|
|||
// 5 E3 CS1
|
|||
// 2 E4 CS2
|
|||
// 78 E2 SCK
|
|||
//
|
|||
#define THERMO_SCK_PIN 78 // E2
|
|||
#define THERMO_DO_PIN 3 // E5
|
|||
#define THERMO_CS1 5 // E3
|
|||
#define THERMO_CS2 2 // E4
|
|||
|
|||
//
|
|||
// Augmentation for auto-assigning plugs
|
|||
//
|
|||
// Two thermocouple connectors allows for either
|
|||
// 2 extruders or 1 extruder and a heated bed.
|
|||
// With no heated bed, an additional 24V fan is possible.
|
|||
//
|
|||
#define MOSFET_A_PIN 6 // H3
|
|||
#define MOSFET_B_PIN 9 // B5
|
|||
#define MOSFET_C_PIN 45 // L4
|
|||
#define MOSFET_D_PIN 44 // L5
|
|||
|
|||
#if HOTENDS > 1 |
|||
#if TEMP_SENSOR_BED |
|||
#define IS_EEB |
|||
#else |
|||
#define IS_EEF |
|||
#endif |
|||
#elif TEMP_SENSOR_BED |
|||
#define IS_EFB |
|||
#else |
|||
#define IS_EFF |
|||
#endif |
|||
|
|||
//
|
|||
// Heaters / Fans (24V)
|
|||
//
|
|||
#define HEATER_0_PIN MOSFET_A_PIN |
|||
|
|||
#if ENABLED(IS_EFB) // Hotend, Fan, Bed
|
|||
#define FAN_PIN MOSFET_B_PIN |
|||
#define HEATER_BED_PIN MOSFET_C_PIN |
|||
#elif ENABLED(IS_EEF) // Hotend, Hotend, Fan
|
|||
#define HEATER_1_PIN MOSFET_B_PIN |
|||
#define FAN_PIN MOSFET_C_PIN |
|||
#elif ENABLED(IS_EEB) // Hotend, Hotend, Bed
|
|||
#define HEATER_1_PIN MOSFET_B_PIN |
|||
#define HEATER_BED_PIN MOSFET_C_PIN |
|||
#elif ENABLED(IS_EFF) // Hotend, Fan, Fan
|
|||
#define FAN_PIN MOSFET_B_PIN |
|||
#define FAN1_PIN MOSFET_C_PIN |
|||
#elif ENABLED(IS_SF) // Spindle, Fan
|
|||
#define FAN_PIN MOSFET_C_PIN |
|||
#endif |
|||
|
|||
#ifndef FAN_PIN |
|||
#define FAN_PIN MOSFET_D_PIN |
|||
#endif |
|||
|
|||
//
|
|||
// Extruder Auto Fan Pins
|
|||
//
|
|||
#define EXTRUDER_0_AUTO_FAN 7 // H4
|
|||
#define EXTRUDER_1_AUTO_FAN 12 // B6
|
|||
|
|||
//
|
|||
// Misc. Functions
|
|||
//
|
|||
#define LED_PIN 13 // B7
|
|||
#define CUTOFF_RESET_PIN 16 // H1
|
|||
#define CUTOFF_TEST_PIN 17 // H0
|
|||
|
|||
//
|
|||
// LCD / Controller
|
|||
//
|
|||
// Replicator uses a 3-wire SR controller with HD44780
|
|||
// For now, pretend it's the SAV
|
|||
//
|
|||
#define SAV_3DLCD |
|||
#define SR_DATA_PIN 34 // C3
|
|||
#define SR_CLK_PIN 35 // C2
|
|||
#define SR_STROBE_PIN 33 // C4
|
|||
|
|||
#define BTN_UP 75 // J4
|
|||
#define BTN_DOWN 73 // J3
|
|||
#define BTN_LEFT 72 // J2
|
|||
#define BTN_RIGHT 14 // J1
|
|||
#define BTN_CENTER 15 // J0
|
|||
#define BTN_ENC BTN_CENTER |
|||
|
|||
#define BEEPER_PIN 4 // G5
|
|||
|
|||
#define STAT_LED_RED 32 // C5
|
|||
#define STAT_LED_BLUE 31 // C6 (Actually green)
|
|||
|
|||
//
|
|||
// SD Card
|
|||
//
|
|||
#define SDSS 53 // B0
|
|||
#define SD_DETECT_PIN 30 // C7
|
|||
|
|||
Loading…
Reference in new issue