diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index b8c41301c9..dd5fe41525 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -27,10 +27,10 @@ #define THERMISTORHEATER_2 3 #define THERMISTORBED 3 +//#define HEATER_0_USES_THERMISTOR //#define HEATER_1_USES_THERMISTOR -//#define HEATER_2_USES_THERMISTOR -#define HEATER_1_USES_AD595 -//#define HEATER_2_USES_AD595 +#define HEATER_0_USES_AD595 +//#define HEATER_1_USES_AD595 // Select one of these only to define how the bed temp is read. //#define BED_USES_THERMISTOR @@ -47,8 +47,8 @@ const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the // For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false // This determines the communication speed of the printer -//#define BAUDRATE 250000 -#define BAUDRATE 115200 +#define BAUDRATE 250000 +//#define BAUDRATE 115200 //#define BAUDRATE 230400 // Comment out (using // at the start of the line) to disable SD support: @@ -57,7 +57,7 @@ const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the #define LCD_WIDTH 16 #define LCD_HEIGHT 2 -//#define ULTIPANEL +#define ULTIPANEL #ifdef ULTIPANEL //#define NEWPANEL //enable this if you have a click-encoder panel #define SDSUPPORT @@ -157,15 +157,17 @@ const int dropsegments=5; //everything with this number of steps will be ignore //#define TEMP_HYSTERESIS 5 // (C°) range of +/- temperatures considered "close" to the target one //// The minimal temperature defines the temperature below which the heater will not be enabled -#define MINTEMP 5 -#define BED_MINTEMP 5 +#define HEATER_0_MINTEMP 5 +//#define HEATER_1_MINTEMP 5 +//#define BED_MINTEMP 5 // When temperature exceeds max temp, your heater will be switched off. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // You should use MINTEMP for thermistor short/failure protection. -#define MAXTEMP 275 -#define BED_MAXTEMP 150 +#define HEATER_0_MAXTEMP 275 +//#define_HEATER_1_MAXTEMP 275 +//#define BED_MAXTEMP 150 /// PID settings: // Uncomment the following line to enable PID support. diff --git a/Marlin/Marlin.h b/Marlin/Marlin.h index cc43f00b2d..130cd865e8 100644 --- a/Marlin/Marlin.h +++ b/Marlin/Marlin.h @@ -57,7 +57,7 @@ void ClearToSend(); void get_coordinates(); void prepare_move(); -void kill(byte debug); +void kill(); //void check_axes_activity(); //void plan_init(); diff --git a/Marlin/Marlin.pde b/Marlin/Marlin.pde index cb55131df3..a95ae1fe9c 100644 --- a/Marlin/Marlin.pde +++ b/Marlin/Marlin.pde @@ -54,6 +54,8 @@ char version_string[] = "1.0.0 Alpha 1"; //------------------- // G0 -> G1 // G1 - Coordinated Movement X Y Z E +// G2 - CW ARC +// G3 - CCW ARC // G4 - Dwell S or P // G28 - Home all Axis // G90 - Use Absolute Coordinates diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index 7a9c56e10b..4406e94806 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -68,11 +68,18 @@ unsigned long previous_millis_heater, previous_millis_bed_heater; float Kc=DEFAULT_Kc; #endif //PIDTEMP -#ifdef MINTEMP -int minttemp = temp2analog(MINTEMP); +#ifdef HEATER_0_MINTEMP +int minttemp_0 = temp2analog(HEATER_0_MINTEMP); #endif //MINTEMP -#ifdef MAXTEMP -int maxttemp = temp2analog(MAXTEMP); +#ifdef HEATER_0_MAXTEMP +int maxttemp_0 = temp2analog(HEATER_0_MAXTEMP); +#endif //MAXTEMP + +#ifdef HEATER_1_MINTEMP +int minttemp_1 = temp2analog(HEATER_1_MINTEMP); +#endif //MINTEMP +#ifdef HEATER_1_MAXTEMP +int maxttemp_1 = temp2analog(HEATER_1_MAXTEMP); #endif //MAXTEMP #ifdef BED_MINTEMP @@ -173,29 +180,28 @@ CRITICAL_SECTION_END; // For a thermistor, it uses the RepRap thermistor temp table. // This is needed because PID in hydra firmware hovers around a given analog value, not a temp value. // This function is derived from inversing the logic from a portion of getTemperature() in FiveD RepRap firmware. -float temp2analog(int celsius) { - #ifdef HEATER_USES_THERMISTOR_1 +int temp2analog(int celsius) { + #ifdef HEATER_0_USES_THERMISTOR int raw = 0; byte i; - for (i=1; i raw) + if (heater_0_temptable[i][0] > raw) { - celsius = temptable_1[i-1][1] + - (raw - temptable_1[i-1][0]) * - (temptable_1[i][1] - temptable_1[i-1][1]) / - (temptable_1[i][0] - temptable_1[i-1][0]); + celsius = heater_0_temptable[i-1][1] + + (raw - heater_0_temptable[i-1][0]) * + (float)(heater_0_temptable[i][1] - heater_0_temptable[i-1][1]) / + (float)(heater_0_temptable[i][0] - heater_0_temptable[i-1][0]); break; } } // Overflow: Set to last value in the table - if (i == NUMTEMPS_HEATER_1) celsius = temptable_1[i-1][1]; + if (i == NUMTEMPS_HEATER_0) celsius = heater_0_temptable[i-1][1]; return celsius; - #elif defined HEATER_1_USES_AD595 + #elif defined HEATER_0_USES_AD595 return raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR; #endif } @@ -403,13 +409,13 @@ ISR(TIMER0_COMPB_vect) if(temp_count >= 16) // 6 ms * 16 = 96ms. { - #ifdef HEATER_1_USES_AD595 + #ifdef HEATER_0_USES_AD595 current_raw[0] = raw_temp_0_value; #else current_raw[0] = 16383 - raw_temp_0_value; #endif - #ifdef HEATER_2_USES_AD595 + #ifdef HEATER_1_USES_AD595 current_raw[2] = raw_temp_2_value; #else current_raw[2] = 16383 - raw_temp_2_value; @@ -426,35 +432,43 @@ ISR(TIMER0_COMPB_vect) raw_temp_0_value = 0; raw_temp_1_value = 0; raw_temp_2_value = 0; -#ifdef MAXTEMP +#ifdef HEATER_0_MAXTEMP #if (HEATER_0_PIN > -1) - if(current_raw[0] >= maxttemp) { + if(current_raw[0] >= maxttemp_0) { target_raw[0] = 0; analogWrite(HEATER_0_PIN, 0); Serial.println("!! Temperature extruder 0 switched off. MAXTEMP triggered !!"); + kill(); } #endif - #if (HEATER_2_PIN > -1) - if(current_raw[2] >= maxttemp) { +#endif +#ifdef HEATER_1_MAXTEMP + #if (HEATER_1_PIN > -1) + if(current_raw[2] >= maxttemp_1) { target_raw[2] = 0; analogWrite(HEATER_2_PIN, 0); Serial.println("!! Temperature extruder 1 switched off. MAXTEMP triggered !!"); + kill() } #endif #endif //MAXTEMP -#ifdef MINTEMP +#ifdef HEATER_0_MINTEMP #if (HEATER_0_PIN > -1) - if(current_raw[0] <= minttemp) { + if(current_raw[0] <= minttemp_0) { target_raw[0] = 0; analogWrite(HEATER_0_PIN, 0); Serial.println("!! Temperature extruder 0 switched off. MINTEMP triggered !!"); + kill(); } #endif +#endif +#ifdef HEATER_1_MINTEMP #if (HEATER_2_PIN > -1) - if(current_raw[2] <= minttemp) { + if(current_raw[2] <= minttemp_1) { target_raw[2] = 0; analogWrite(HEATER_2_PIN, 0); Serial.println("!! Temperature extruder 1 switched off. MINTEMP triggered !!"); + kill(); } #endif #endif //MAXTEMP @@ -464,6 +478,7 @@ ISR(TIMER0_COMPB_vect) target_raw[1] = 0; WRITE(HEATER_1_PIN, 0); Serial.println("!! Temperatur heated bed switched off. MINTEMP triggered !!"); + kill(); } #endif #endif @@ -473,6 +488,7 @@ ISR(TIMER0_COMPB_vect) target_raw[1] = 0; WRITE(HEATER_1_PIN, 0); Serial.println("!! Temperature heated bed switched off. MAXTEMP triggered !!"); + kill(); } #endif #endif diff --git a/Marlin/temperature.h b/Marlin/temperature.h index 986aca9998..7d9b7926e9 100644 --- a/Marlin/temperature.h +++ b/Marlin/temperature.h @@ -27,8 +27,8 @@ void tp_init(); void manage_heater(); //int temp2analogu(int celsius, const short table[][2], int numtemps); //float analog2tempu(int raw, const short table[][2], int numtemps); -float temp2analog(int celsius); -float temp2analogBed(int celsius); +int temp2analog(int celsius); +int temp2analogBed(int celsius); float analog2temp(int raw); float analog2tempBed(int raw); diff --git a/Marlin/thermistortables.h b/Marlin/thermistortables.h index 0ea1991dce..9e3af6c52b 100644 --- a/Marlin/thermistortables.h +++ b/Marlin/thermistortables.h @@ -3,7 +3,7 @@ #define OVERSAMPLENR 16 -#if (THERMISTORHEATER_1 == 1) || (THERMISTORHEATER_2 == 1) || (THERMISTORBED == 1) //100k bed thermistor +#if (THERMISTORHEATER_0 == 1) || (THERMISTORHEATER_1 == 1) || (THERMISTORBED == 1) //100k bed thermistor #define NUMTEMPS_1 61 const short temptable_1[NUMTEMPS_1][2] = { @@ -70,7 +70,7 @@ const short temptable_1[NUMTEMPS_1][2] = { { 1008*OVERSAMPLENR , 0 } //safety }; #endif -#if (THERMISTORHEATER_1 == 2) || (THERMISTORHEATER_2 == 2) || (THERMISTORBED == 2) //200k bed thermistor +#if (THERMISTORHEATER_0 == 2) || (THERMISTORHEATER_1 == 2) || (THERMISTORBED == 2) //200k bed thermistor #define NUMTEMPS_2 21 const short temptable_2[NUMTEMPS_2][2] = { {1*OVERSAMPLENR, 848}, @@ -97,7 +97,7 @@ const short temptable_2[NUMTEMPS_2][2] = { }; #endif -#if (THERMISTORHEATER_1 == 3) || (THERMISTORHEATER_2 == 3) || (THERMISTORBED == 3) //mendel-parts +#if (THERMISTORHEATER_0 == 3) || (THERMISTORHEATER_1 == 3) || (THERMISTORBED == 3) //mendel-parts #define NUMTEMPS_3 28 const short temptable_3[NUMTEMPS_3][2] = { {1*OVERSAMPLENR,864}, @@ -131,7 +131,7 @@ const short temptable_3[NUMTEMPS_3][2] = { }; #endif -#if (THERMISTORHEATER_1 == 4) || (THERMISTORHEATER_2 == 4) || (THERMISTORBED == 4) //10k thermistor +#if (THERMISTORHEATER_0 == 4) || (THERMISTORHEATER_1 == 4) || (THERMISTORBED == 4) //10k thermistor #define NUMTEMPS_4 20 short temptable_4[NUMTEMPS_4][2] = { @@ -158,7 +158,7 @@ short temptable_4[NUMTEMPS_4][2] = { }; #endif -#if (THERMISTORHEATER_1 == 5) || (THERMISTORHEATER_2 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2) +#if (THERMISTORHEATER_0 == 5) || (THERMISTORHEATER_1 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2) #define NUMTEMPS_5 61 const short temptable_5[NUMTEMPS_5][2] = { @@ -226,7 +226,7 @@ const short temptable_5[NUMTEMPS_5][2] = { }; #endif -#if (THERMISTORHEATER_1 == 6) || (THERMISTORHEATER_2 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor +#if (THERMISTORHEATER_0 == 6) || (THERMISTORHEATER_1 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor #define NUMTEMPS_6 36 const short temptable_6[NUMTEMPS_6][2] = { {28*OVERSAMPLENR, 250}, @@ -268,7 +268,7 @@ const short temptable_6[NUMTEMPS_6][2] = { }; #endif -#if (THERMISTORHEATER_1 == 7) || (THERMISTORHEATER_2 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01 +#if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01 #define NUMTEMPS_7 54 const short temptable_7[NUMTEMPS_7][2] = { {46*OVERSAMPLENR, 270}, @@ -330,56 +330,56 @@ const short temptable_7[NUMTEMPS_7][2] = { +#if THERMISTORHEATER_0 == 1 +#define NUMTEMPS_HEATER_0 NUMTEMPS_1 +#define heater_0_temptable temptable_1 +#elif THERMISTORHEATER_0 == 2 +#define NUMTEMPS_HEATER_0 NUMTEMPS_2 +#define heater_0_temptable temptable_2 +#elif THERMISTORHEATER_0 == 3 +#define NUMTEMPS_HEATER_0 NUMTEMPS_3 +#define heater_0_temptable temptable_3 +#elif THERMISTORHEATER_0 == 4 +#define NUMTEMPS_HEATER_0 NUMTEMPS_4 +#define heater_0_temptable temptable_4 +#elif THERMISTORHEATER_0 == 5 +#define NUMTEMPS_HEATER_0 NUMTEMPS_5 +#define heater_0_temptable temptable_5 +#elif THERMISTORHEATER_0 == 6 +#define NUMTEMPS_HEATER_0 NUMTEMPS_6 +#define heater_0_temptable temptable_6 +#elif THERMISTORHEATER_0 == 7 +#define NUMTEMPS_HEATER_0 NUMTEMPS_7 +#define heater_0_temptable temptable_7 +#elif defined HEATER_0_USES_THERMISTOR +#error No heater 0 thermistor table specified +#endif + #if THERMISTORHEATER_1 == 1 #define NUMTEMPS_HEATER_1 NUMTEMPS_1 -#define temptable_1 temptable_1 +#define heater_1_temptable temptable_1 #elif THERMISTORHEATER_1 == 2 #define NUMTEMPS_HEATER_1 NUMTEMPS_2 -#define temptable_1 temptable_2 +#define heater_1_temptable temptable_2 #elif THERMISTORHEATER_1 == 3 #define NUMTEMPS_HEATER_1 NUMTEMPS_3 -#define temptable_1 temptable_3 +#define heater_1_temptable temptable_3 #elif THERMISTORHEATER_1 == 4 #define NUMTEMPS_HEATER_1 NUMTEMPS_4 -#define temptable_1 temptable_4 +#define heater_1_temptable temptable_4 #elif THERMISTORHEATER_1 == 5 #define NUMTEMPS_HEATER_1 NUMTEMPS_5 -#define temptable_1 temptable_5 +#define heater_1_temptable temptable_5 #elif THERMISTORHEATER_1 == 6 #define NUMTEMPS_HEATER_1 NUMTEMPS_6 -#define temptable_1 temptable_6 +#define heater_1_temptable temptable_6 #elif THERMISTORHEATER_1 == 7 #define NUMTEMPS_HEATER_1 NUMTEMPS_7 -#define temptable_1 temptable_7 +#define heater_1_temptable temptable_7 #elif defined HEATER_1_USES_THERMISTOR #error No heater 1 thermistor table specified #endif -#if THERMISTORHEATER_2 == 1 -#define NUMTEMPS_HEATER_2 NUMTEMPS_1 -#define temptable_2 temptable_1 -#elif THERMISTORHEATER_2 == 2 -#define NUMTEMPS_HEATER_2 NUMTEMPS_2 -#define temptable_2 temptable_2 -#elif THERMISTORHEATER_2 == 3 -#define NUMTEMPS_HEATER_2 NUMTEMPS_3 -#define temptable_2 temptable_3 -#elif THERMISTORHEATER_2 == 4 -#define NUMTEMPS_HEATER_2 NUMTEMPS_4 -#define temptable_2 temptable_4 -#elif THERMISTORHEATER_2 == 5 -#define NUMTEMPS_HEATER_2 NUMTEMPS_5 -#define temptable_2 temptable_5 -#elif THERMISTORHEATER_2 == 6 -#define NUMTEMPS_HEATER_2 NUMTEMPS_6 -#define temptable_2 temptable_6 -#elif THERMISTORHEATER_2 == 7 -#define NUMTEMPS_HEATER22 NUMTEMPS_7 -#define temptable_2 temptable_7 -#elif defined HEATER_2_USES_THERMISTOR -#error No heater 2 thermistor table specified -#endif - #if THERMISTORBED == 1 #define BNUMTEMPS NUMTEMPS_1