diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h index 5b0960fdd4..174f9e386e 100644 --- a/Marlin/configurator/config/Configuration.h +++ b/Marlin/configurator/config/Configuration.h @@ -31,7 +31,7 @@ Here are some standard links for getting your machine calibrated: //=========================================================================== //============================= SCARA Printer =============================== //=========================================================================== -// For a Delta printer replace the configuration files with the files in the +// For a Scara printer replace the configuration files with the files in the // example_configurations/SCARA directory. // @@ -65,7 +65,7 @@ Here are some standard links for getting your machine calibrated: // The following define selects which electronics board you have. // Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD - #define MOTHERBOARD BOARD_ULTIMAKER + #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif // Define this to set a custom name for your generic Mendel, @@ -79,10 +79,17 @@ Here are some standard links for getting your machine calibrated: // :[1,2,3,4] #define EXTRUDERS 1 +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX // 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) // :{1:'ATX',2:'X-Box 360'} + #define POWER_SUPPLY 1 // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. @@ -131,9 +138,9 @@ Here are some standard links for getting your machine calibrated: // Use it for Testing or Development purposes. NEVER for production machine. // #define DUMMY_THERMISTOR_998_VALUE 25 // #define DUMMY_THERMISTOR_999_VALUE 100 -// :{ 0: "Not used", 4: "10k !! do not use for a hotend. Bad resolution at high temp. !!", 1: "100k / 4.7k - EPCOS", 51: "100k / 1k - EPCOS", 6: "100k / 4.7k EPCOS - Not as accurate as Table 1", 5: "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 7: "100k / 4.7k Honeywell 135-104LAG-J01", 71: "100k / 4.7k Honeywell 135-104LAF-J01", 8: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", 9: "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", 10: "100k / 4.7k RS 198-961", 11: "100k / 4.7k beta 3950 1%", 12: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", 13: "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", 60: "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", 55: "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 2: "200k / 4.7k - ATC Semitec 204GT-2", 52: "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", 3: "Mendel-parts / 4.7k", 1047: "Pt1000 / 4.7k", 1010: "Pt1000 / 1k (non standard)", 20: "PT100 (Ultimainboard V2.x)", 147: "Pt100 / 4.7k", 110: "Pt100 / 1k (non-standard)", 998: "Dummy 1", 999: "Dummy 2" } -#define TEMP_SENSOR_0 -1 -#define TEMP_SENSOR_1 -1 + +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 #define TEMP_SENSOR_2 0 #define TEMP_SENSOR_3 0 #define TEMP_SENSOR_BED 0 @@ -327,6 +334,7 @@ your extruder heater takes 2 minutes to hit the target on heating. // #define ENDSTOPPULLUP_XMIN // #define ENDSTOPPULLUP_YMIN // #define ENDSTOPPULLUP_ZMIN + // #define ENDSTOPPULLUP_ZPROBE #endif // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). @@ -336,10 +344,16 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. +const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. //#define DISABLE_MAX_ENDSTOPS //#define DISABLE_MIN_ENDSTOPS // @section machine +// If you want to enable the Z Probe pin, but disable its use, uncomment the line below. +// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have +// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe, +// this has no effect. +//#define DISABLE_Z_PROBE_ENDSTOP // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} @@ -361,9 +375,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o // @section machine // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR true +#define INVERT_X_DIR false #define INVERT_Y_DIR false -#define INVERT_Z_DIR true +#define INVERT_Z_DIR false // @section extruder @@ -391,8 +405,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o #define X_MIN_POS 0 #define Y_MIN_POS 0 #define Z_MIN_POS 0 -#define X_MAX_POS 205 -#define Y_MAX_POS 205 +#define X_MAX_POS 200 +#define Y_MAX_POS 200 #define Z_MAX_POS 200 //=========================================================================== @@ -561,18 +575,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o // default settings -#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts +#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker +#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. -// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). -// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). -// For the other hotends it is their distance from the extruder 0 hotend. -// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) #define DEFAULT_XYJERK 20.0 // (mm/sec) @@ -614,11 +623,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o // Preheat Constants #define PLA_PREHEAT_HOTEND_TEMP 180 #define PLA_PREHEAT_HPB_TEMP 70 -#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 +#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 #define ABS_PREHEAT_HOTEND_TEMP 240 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 +#define ABS_PREHEAT_HPB_TEMP 110 +#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 //==============================LCD and SD support============================= // @section lcd @@ -626,7 +635,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o // Define your display language below. Replace (en) with your language code and uncomment. // en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test // See also language.h -//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) +#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) // Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. // To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. @@ -730,7 +739,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ // #define PHOTOGRAPH_PIN 23 -// SF send wrong arc g-codes when using Arc Point as fillet procedure +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure //#define SF_ARC_FIX // Support for the BariCUDA Paste Extruder. @@ -784,7 +793,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) //defines used in the code -#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially +#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY diff --git a/Marlin/configurator/config/Configuration_adv.h b/Marlin/configurator/config/Configuration_adv.h index 8acdeb969c..daf3144d9e 100644 --- a/Marlin/configurator/config/Configuration_adv.h +++ b/Marlin/configurator/config/Configuration_adv.h @@ -192,7 +192,7 @@ #define X_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5 #define Z_HOME_BUMP_MM 2 -#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate) //#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. // @section machine @@ -335,7 +335,7 @@ #define EXTRUDER_ADVANCE_K .0 #define D_FILAMENT 2.85 #define STEPS_MM_E 836 -#endif // ADVANCE +#endif // Arc interpretation settings: #define MM_PER_ARC_SEGMENT 1 diff --git a/Marlin/configurator/config/boards.h b/Marlin/configurator/config/boards.h index 0798139787..8a60f011d5 100644 --- a/Marlin/configurator/config/boards.h +++ b/Marlin/configurator/config/boards.h @@ -10,10 +10,11 @@ #define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0 #define BOARD_SETHI 20 // Sethi 3D_1 #define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2 -#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Extruder, Fan, Bed) -#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Extruder0, Extruder1, Bed) -#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Extruder, Fan, Fan) -#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Extruder0, Extruder1, Fan) +#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) +#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) +#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) +#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan) +#define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like) #define BOARD_DUEMILANOVE_328P 4 // Duemilanove w/ ATMega328P pin assignments #define BOARD_GEN6 5 // Gen6 #define BOARD_GEN6_DELUXE 51 // Gen6 deluxe @@ -28,14 +29,15 @@ #define BOARD_ULTIMAKER 7 // Ultimaker #define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare) #define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20) -#define BOARD_3DRAG 77 // 3Drag -#define BOARD_K8200 78 // Vellemann K8200 (derived from 3Drag) +#define BOARD_3DRAG 77 // 3Drag Controller +#define BOARD_K8200 78 // Vellemann K8200 Controller (derived from 3Drag Controller) #define BOARD_TEENSYLU 8 // Teensylu #define BOARD_RUMBA 80 // Rumba #define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286) #define BOARD_BRAINWAVE 82 // Brainwave (AT90USB646) #define BOARD_SAV_MKI 83 // SAV Mk-I (AT90USB1286) #define BOARD_TEENSY2 84 // Teensy++2.0 (AT90USB1286) - CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make +#define BOARD_BRAINWAVE_PRO 85 // Brainwave Pro (AT90USB1286) #define BOARD_GEN3_PLUS 9 // Gen3+ #define BOARD_GEN3_MONOLITHIC 22 // Gen3 Monolithic Electronics #define BOARD_MEGATRONICS 70 // Megatronics @@ -50,10 +52,11 @@ #define BOARD_LEAPFROG 999 // Leapfrog #define BOARD_WITBOX 41 // bq WITBOX #define BOARD_HEPHESTOS 42 // bq Prusa i3 Hephestos +#define BOARD_BAM_DICE 401 // 2PrintBeta BAM&DICE with STK drivers +#define BOARD_BAM_DICE_DUE 402 // 2PrintBeta BAM&DICE Due with STK drivers #define BOARD_99 99 // This is in pins.h but...? #define MB(board) (MOTHERBOARD==BOARD_##board) -#define IS_RAMPS (MB(RAMPS_OLD) || MB(RAMPS_13_EFB) || MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF)) #endif //__BOARDS_H diff --git a/Marlin/configurator/config/language.h b/Marlin/configurator/config/language.h index f1193b9244..3fe7afd2ed 100644 --- a/Marlin/configurator/config/language.h +++ b/Marlin/configurator/config/language.h @@ -11,28 +11,35 @@ // // ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h" // ==> ALSO TRY ALL AVAILABLE LANGUAGE OPTIONS +// See also documentation/LCDLanguageFont.md // Languages -// en English -// pl Polish -// fr French -// de German -// es Spanish -// ru Russian -// it Italian -// pt Portuguese -// pt-br Portuguese (Brazil) -// fi Finnish -// an Aragonese -// nl Dutch -// ca Catalan -// eu Basque-Euskera +// en English +// pl Polish +// fr French +// de German +// es Spanish +// ru Russian +// it Italian +// pt Portuguese +// pt-br Portuguese (Brazil) +// fi Finnish +// an Aragonese +// nl Dutch +// ca Catalan +// eu Basque-Euskera +// kana Japanese +// kana_utf Japanese #ifndef LANGUAGE_INCLUDE // pick your language from the list above #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) #endif +#ifdef HAS_AUTOMATIC_VERSIONING + #include "_Version.h" +#endif + #define PROTOCOL_VERSION "1.0" #if MB(ULTIMAKER)|| MB(ULTIMAKER_OLD)|| MB(ULTIMAIN_2) @@ -56,18 +63,37 @@ #elif MB(HEPHESTOS) #define MACHINE_NAME "HEPHESTOS" #define FIRMWARE_URL "http://www.bq.com/gb/downloads-prusa-i3-hephestos.html" -#else // Default firmware set to Mendel - #define MACHINE_NAME "Mendel" - #define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin" +#elif MB(BRAINWAVE_PRO) + #define MACHINE_NAME "Kossel Pro" + #ifndef FIRMWARE_URL + #define FIRMWARE_URL "https://github.com/OpenBeamUSA/Marlin/" + #endif +#else + #ifndef MACHINE_NAME + #define MACHINE_NAME "Mendel" + #endif #endif #ifdef CUSTOM_MENDEL_NAME + #warning CUSTOM_MENDEL_NAME deprecated - use CUSTOM_MACHINE_NAME + #define CUSTOM_MACHINE_NAME CUSTOM_MENDEL_NAME +#endif + +#ifdef CUSTOM_MACHINE_NAME #undef MACHINE_NAME - #define MACHINE_NAME CUSTOM_MENDEL_NAME + #define MACHINE_NAME CUSTOM_MACHINE_NAME +#endif + +#ifndef FIRMWARE_URL + #define FIRMWARE_URL "https://github.com/MarlinFirmware/Marlin" +#endif + +#ifndef BUILD_VERSION + #define BUILD_VERSION "V1; Sprinter/grbl mashup for gen6" #endif #ifndef MACHINE_UUID - #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" #endif @@ -114,7 +140,7 @@ #define MSG_HEATING_COMPLETE "Heating done." #define MSG_BED_HEATING "Bed Heating." #define MSG_BED_DONE "Bed done." -#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n" +#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin " BUILD_VERSION " FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n" #define MSG_COUNT_X " Count X: " #define MSG_ERR_KILLED "Printer halted. kill() called!" #define MSG_ERR_STOPPED "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)" @@ -122,12 +148,15 @@ #define MSG_UNKNOWN_COMMAND "Unknown command: \"" #define MSG_ACTIVE_EXTRUDER "Active Extruder: " #define MSG_INVALID_EXTRUDER "Invalid extruder" +#define MSG_INVALID_SOLENOID "Invalid solenoid" #define MSG_X_MIN "x_min: " #define MSG_X_MAX "x_max: " #define MSG_Y_MIN "y_min: " #define MSG_Y_MAX "y_max: " #define MSG_Z_MIN "z_min: " #define MSG_Z_MAX "z_max: " +#define MSG_Z2_MAX "z2_max: " +#define MSG_Z_PROBE "z_probe: " #define MSG_M119_REPORT "Reporting endstop status" #define MSG_ENDSTOP_HIT "TRIGGERED" #define MSG_ENDSTOP_OPEN "open" @@ -160,68 +189,48 @@ #define MSG_ERR_EEPROM_WRITE "Error writing to EEPROM!" +// temperature.cpp strings +#define MSG_PID_AUTOTUNE "PID Autotune" +#define MSG_PID_AUTOTUNE_START MSG_PID_AUTOTUNE " start" +#define MSG_PID_AUTOTUNE_FAILED MSG_PID_AUTOTUNE " failed!" +#define MSG_PID_BAD_EXTRUDER_NUM MSG_PID_AUTOTUNE_FAILED " Bad extruder number" +#define MSG_PID_TEMP_TOO_HIGH MSG_PID_AUTOTUNE_FAILED " Temperature too high" +#define MSG_PID_TIMEOUT MSG_PID_AUTOTUNE_FAILED " timeout" +#define MSG_BIAS " bias: " +#define MSG_D " d: " +#define MSG_T_MIN " min: " +#define MSG_T_MAX " max: " +#define MSG_KU " Ku: " +#define MSG_TU " Tu: " +#define MSG_CLASSIC_PID " Classic PID " +#define MSG_KP " Kp: " +#define MSG_KI " Ki: " +#define MSG_KD " Kd: " +#define MSG_OK_B "ok B:" +#define MSG_OK_T "ok T:" +#define MSG_AT " @:" +#define MSG_PID_AUTOTUNE_FINISHED MSG_PID_AUTOTUNE " finished! Put the last Kp, Ki and Kd constants from above into Configuration.h" +#define MSG_PID_DEBUG " PID_DEBUG " +#define MSG_PID_DEBUG_INPUT ": Input " +#define MSG_PID_DEBUG_OUTPUT " Output " +#define MSG_PID_DEBUG_PTERM " pTerm " +#define MSG_PID_DEBUG_ITERM " iTerm " +#define MSG_PID_DEBUG_DTERM " dTerm " +#define MSG_HEATING_FAILED "Heating failed" +#define MSG_EXTRUDER_SWITCHED_OFF "Extruder switched off. Temperature difference between temp sensors is too high !" + +#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !" +#define MSG_THERMAL_RUNAWAY_STOP "Thermal Runaway, system stopped! Heater_ID: " +#define MSG_SWITCHED_OFF_MAX " switched off. MAXTEMP triggered !!" +#define MSG_MINTEMP_EXTRUDER_OFF ": Extruder switched off. MINTEMP triggered !" +#define MSG_MAXTEMP_EXTRUDER_OFF ": Extruder" MSG_SWITCHED_OFF_MAX +#define MSG_MAXTEMP_BED_OFF "Heated bed" MSG_SWITCHED_OFF_MAX + // LCD Menu Messages -// Add your own character. Reference: https://github.com/MarlinFirmware/Marlin/pull/1434 photos -// and https://www.sparkfun.com/datasheets/LCD/HD44780.pdf page 17-18 -#ifdef DOGLCD - #define STR_Ae "\304" // 'Ä' U8glib - #define STR_ae "\344" // 'ä' - #define STR_Oe "\326" // 'Ö' - #define STR_oe STR_Oe // 'ö' - #define STR_Ue "\334" // 'Ü' - #define STR_ue STR_Ue // 'ü' - #define STR_sz "\337" // 'ß' - #define STR_h2 "\262" // '²' - #define STR_h3 "\263" // '³' - #define STR_Deg "\260" // '°' - #define STR_THERMOMETER "\377" -#else - #ifdef DISPLAY_CHARSET_HD44780_JAPAN // HD44780 ROM Code: A00 (Japan) - #define STR_ae "\xe1" - #define STR_Ae STR_ae - #define STR_oe "\357" - #define STR_Oe STR_oe - #define STR_ue "\365" - #define STR_Ue STR_ue - #define STR_sz "\342" - #define STR_h2 "2" - #define STR_h3 "3" - #define STR_Deg "\271" - #define STR_THERMOMETER "\002" - #endif - #ifdef DISPLAY_CHARSET_HD44780_WESTERN // HD44780 ROM Code: A02 (Western) - #define STR_Ae "\216" - #define STR_ae "\204" - #define STR_Oe "\211" - #define STR_oe "\204" - #define STR_Ue "\212" - #define STR_ue "\201" - #define STR_sz "\160" - #define STR_h2 "\262" - #define STR_h3 "\263" - #define STR_Deg "\337" - #define STR_THERMOMETER "\002" - #endif +#if !(defined( DISPLAY_CHARSET_HD44780_JAPAN ) || defined( DISPLAY_CHARSET_HD44780_WESTERN ) || defined( DISPLAY_CHARSET_HD44780_CYRILLIC )) + #define DISPLAY_CHARSET_HD44780_JAPAN #endif -/* -#define TESTSTRING000 "\000\001\002\003\004\005\006\007\010\011\012\013\014\015\016\017" -#define TESTSTRING020 "\020\021\022\023\024\025\026\027\030\031\032\033\034\035\036\037" -#define TESTSTRING040 "\040\041\042\043\044\045\046\047\050\051\052\053\054\055\056\057" -#define TESTSTRING060 "\060\061\062\063\064\065\066\067\070\071\072\073\074\075\076\077" -#define TESTSTRING100 "\100\101\102\103\104\105\106\107\110\111\112\113\114\115\116\117" -#define TESTSTRING120 "\120\121\122\123\124\125\126\127\130\131\132\133\134\135\136\137" -#define TESTSTRING140 "\140\141\142\143\144\145\146\147\150\151\152\153\154\155\156\157" -#define TESTSTRING160 "\160\161\162\163\164\165\166\167\170\171\172\173\174\175\176\177" -#define TESTSTRING200 "\200\201\202\203\204\205\206\207\210\211\212\213\214\215\216\217" -#define TESTSTRING220 "\220\221\222\223\224\225\226\227\230\231\232\233\234\235\236\237" -#define TESTSTRING240 "\240\241\242\243\244\245\246\247\250\251\252\253\254\255\256\257" -#define TESTSTRING260 "\260\261\262\263\264\265\266\267\270\271\272\273\274\275\276\277" -#define TESTSTRING300 "\300\301\302\303\304\305\306\307\310\311\312\313\314\315\316\317" -#define TESTSTRING320 "\320\321\322\323\324\325\326\327\330\331\332\333\334\335\336\337" -#define TESTSTRING340 "\340\341\342\343\344\345\346\347\350\351\352\353\354\355\356\357" -#define TESTSTRING360 "\360\361\362\363\364\365\366\367\370\371\372\373\374\375\376\377" -*/ #include LANGUAGE_INCLUDE #include "language_en.h"