Fix up some units comments

Marlin/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/default/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Anet/A2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Einstart-S/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Formbot/Raptor/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -468,7 +468,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -469,7 +469,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/MakerParts/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 180  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5  // mm
+  #define EXTRUDER_RUNOUT_SPEED 180  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5  // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/TheBorg/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -189,8 +189,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -477,7 +477,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -596,29 +596,29 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - MIN_PROBE_EDGE  // mm
+    #define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - MIN_PROBE_EDGE  // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   #if ENABLED(ANYCUBIC_KOSSEL_PLUS)
     // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-    #define DELTA_PRINTABLE_RADIUS 116.0 // mm
+    #define DELTA_PRINTABLE_RADIUS 116.0 // (mm)
     // Center-to-center distance of the holes in the diagonal push rods.
-    #define DELTA_DIAGONAL_ROD 267 // mm
+    #define DELTA_DIAGONAL_ROD 267 // (mm)
       // Horizontal offset from middle of printer to smooth rod center.
-    #define DELTA_SMOOTH_ROD_OFFSET 186 // mm
+    #define DELTA_SMOOTH_ROD_OFFSET 186 // (mm)
     // Horizontal offset of the universal joints on the end effector.
-    #define DELTA_EFFECTOR_OFFSET 31 // mm
+    #define DELTA_EFFECTOR_OFFSET 31 // (mm)
     // Horizontal offset of the universal joints on the carriages.
-    #define DELTA_CARRIAGE_OFFSET 20.6 // mm
+    #define DELTA_CARRIAGE_OFFSET 20.6 // (mm)
     // Horizontal distance bridged by diagonal push rods when effector is centered.
     #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET))  //mm  Get this value from auto calibrate
   #else
     // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-    #define DELTA_PRINTABLE_RADIUS 90.0 // mm
+    #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
     // Center-to-center distance of the holes in the diagonal push rods.
-    #define DELTA_DIAGONAL_ROD 218.0 // mm
+    #define DELTA_DIAGONAL_ROD 218.0 // (mm)
     // Horizontal distance bridged by diagonal push rods when effector is centered.
     #define DELTA_RADIUS 97.0 //mm  Get this value from auto calibrate
   #endif

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -562,16 +562,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 73.5 // mm
+    #define DELTA_CALIBRATION_RADIUS 73.5 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 85.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 85.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 218.0 // mm
+  #define DELTA_DIAGONAL_ROD 218.0 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 295.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

@@ -562,16 +562,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 63 // mm
+    #define DELTA_CALIBRATION_RADIUS 63 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 70.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 70.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 218.0 // mm
+  #define DELTA_DIAGONAL_ROD 218.0 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 317.94 // get this value from auto calibrate

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -562,16 +562,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 73.5 // mm
+    #define DELTA_CALIBRATION_RADIUS 73.5 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 85.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 85.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 218.0 // mm
+  #define DELTA_DIAGONAL_ROD 218.0 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 280.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -567,16 +567,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 121.5 // mm
+    #define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 151.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 151.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 356.5 // mm
+  #define DELTA_DIAGONAL_ROD 356.5 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 352.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -552,16 +552,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 121.5 // mm
+    #define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 140.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 250.0 // mm
+  #define DELTA_DIAGONAL_ROD 250.0 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 250.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -552,16 +552,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 78.0 // mm
+    #define DELTA_CALIBRATION_RADIUS 78.0 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 90.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 215.0 // mm
+  #define DELTA_DIAGONAL_ROD 215.0 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 250.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -538,16 +538,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 110.0 // mm
+    #define DELTA_CALIBRATION_RADIUS 110.0 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 127.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 127.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 301.0 // mm
+  #define DELTA_DIAGONAL_ROD 301.0 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 277.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -556,16 +556,16 @@
 
   #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
     // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
-    #define DELTA_CALIBRATION_RADIUS 121.5 // mm
+    #define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
     // Set the steprate for papertest probing
-    #define PROBE_MANUALLY_STEP 0.05 // mm
+    #define PROBE_MANUALLY_STEP 0.05 // (mm)
   #endif
 
   // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
-  #define DELTA_PRINTABLE_RADIUS 140.0 // mm
+  #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
 
   // Center-to-center distance of the holes in the diagonal push rods.
-  #define DELTA_DIAGONAL_ROD 319.5 // mm
+  #define DELTA_DIAGONAL_ROD 319.5 // (mm)
 
   // height from z=0 to home position
   #define DELTA_HEIGHT 380.00 // get this value from auto calibrate

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -466,7 +466,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -176,8 +176,8 @@
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
-  #define EXTRUDER_RUNOUT_SPEED 1500  // mm/m
-  #define EXTRUDER_RUNOUT_EXTRUDE 5   // mm
+  #define EXTRUDER_RUNOUT_SPEED 1500  // (mm/m)
+  #define EXTRUDER_RUNOUT_EXTRUDE 5   // (mm)
 #endif
 
 // @section temperature
@@ -464,7 +464,7 @@
 // Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
 // of the buffer and all stops. This should not be much greater than zero and should only be changed
 // if unwanted behavior is observed on a user's machine when running at very slow speeds.
-#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
 
 //
 // Use Junction Deviation instead of traditional Jerk Limiting