Gantry: Enable Filament Change (#15122)

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -1463,12 +1463,12 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
-  #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
+  #define NOZZLE_PARK_XY_FEEDRATE 60    // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
 #endif
 

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -1555,14 +1555,14 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
-  #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
+  #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
                                                   // This short retract is done immediately, before parking the nozzle.
   #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH        0  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -1463,12 +1463,12 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
-  #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
+  #define NOZZLE_PARK_XY_FEEDRATE 60    // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
 #endif
 

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -1555,14 +1555,14 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
-  #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
+  #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
                                                   // This short retract is done immediately, before parking the nozzle.
   #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH        0  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.