Browse Source

Clean up some pins

vanilla_fb_2.0.x
Scott Lahteine 4 years ago
parent
commit
c7ecfe28e7
  1. 10
      Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h
  2. 12
      Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h
  3. 36
      Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
  4. 2
      Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h

10
Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h

@ -48,20 +48,20 @@
//
// Limit Switches
//
#define X_STOP_PIN PC1 // "X-STOP"
#define Y_STOP_PIN PC0 // "Y-STOP"
#define Z_STOP_PIN PC15 // "Z-STOP"
#define X_STOP_PIN PC1 // X-STOP
#define Y_STOP_PIN PC0 // Y-STOP
#define Z_STOP_PIN PC15 // Z-STOP
//
// Z Probe must be this pin
//
#define Z_MIN_PROBE_PIN PC14 // "PROBE"
#define Z_MIN_PROBE_PIN PC14 // PROBE
//
// Filament Runout Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PC2 // "E0-STOP"
#define FIL_RUNOUT_PIN PC2 // E0-STOP
#endif
//

12
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h

@ -41,25 +41,25 @@
//
// Servos
//
#define SERVO0_PIN PA1 // "SERVOS"
#define SERVO0_PIN PA1 // SERVOS
//
// Limit Switches
//
#define X_STOP_PIN PC0 // "X-STOP"
#define Y_STOP_PIN PC1 // "Y-STOP"
#define Z_STOP_PIN PC2 // "Z-STOP"
#define X_STOP_PIN PC0 // X-STOP
#define Y_STOP_PIN PC1 // Y-STOP
#define Z_STOP_PIN PC2 // Z-STOP
//
// Z Probe must be this pin
//
#define Z_MIN_PROBE_PIN PC14 // "PROBE"
#define Z_MIN_PROBE_PIN PC14 // PROBE
//
// Filament Runout Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PC15 // "E0-STOP"
#define FIL_RUNOUT_PIN PC15 // E0-STOP
#endif
//

36
Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h

@ -117,11 +117,7 @@
* Several wiring options are provided below, defaulting to
* to the most compatible.
*/
//
// Drivers
//
#if HAS_TMC220x
#if HAS_TMC_UART
// SoftwareSerial with one pin per driver
// Compatible with TMC2208 and TMC2209 drivers
#define X_SERIAL_TX_PIN PA10 // RXD1
@ -140,20 +136,20 @@
#define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
#endif
/**
* MKS Robin_Wifi or another ESP8266 module
*
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
* | nc | | nc | (01) WIFI_CTRL (PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* AE
*/
/**
* MKS Robin_Wifi or another ESP8266 module
*
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
* | nc | | nc | (01) WIFI_CTRL (PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* AE
*/
// Module ESP-WIFI
#define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
@ -303,7 +299,7 @@
#define TFT_MARLINUI_COLOR 0xC7B6 // Green
#define TFT_BTARROWS_COLOR 0xDEE6 // Yellow
#define TFT_BTOKMENU_COLOR 0x145F // Cyan
#endif
#endif
#define TFT_BUFFER_SIZE 14400
#elif HAS_GRAPHICAL_TFT
#define TFT_RESET_PIN PC6

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h

@ -82,7 +82,7 @@
#define E0_DIR_PIN PB3
#define E0_ENABLE_PIN PB5
#if HAS_TMC220x
#if HAS_TMC_UART
/**
* TMC2208/TMC2209 stepper drivers
*

Loading…
Cancel
Save