Доп. меню, скролл имен файлов

Marlin/Configuration.h

@@ -473,8 +473,8 @@
 #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_DEBUG             // Sends debug data to the serial port.
   //#define PID_OPENLOOP 1        // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay

Marlin/Configuration_adv.h

@@ -1118,7 +1118,7 @@
   #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -2841,25 +2841,19 @@
 /**
  * User-defined menu items that execute custom GCode
  */
-//#define CUSTOM_USER_MENUS
+#define CUSTOM_USER_MENUS
 #if ENABLED(CUSTOM_USER_MENUS)
-  //#define CUSTOM_USER_MENU_TITLE "Custom Commands"
-  #define USER_SCRIPT_DONE "M117 User Script Done"
-  #define USER_SCRIPT_AUDIBLE_FEEDBACK
+  #define CUSTOM_USER_MENU_TITLE "Custom Commands"
+  //#define USER_SCRIPT_DONE "M117 User Script Done"
+  //#define USER_SCRIPT_AUDIBLE_FEEDBACK
   //#define USER_SCRIPT_RETURN  // Return to status screen after a script
 
-  #define USER_DESC_1 "Home & UBL Info"
-  #define USER_GCODE_1 "G28\nG29 W"
-
-  #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
-  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
-
-  #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
-  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
-
-  #define USER_DESC_4 "Heat Bed/Home/Level"
-  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+  #define USER_DESC_1 "LED On"
+  #define USER_GCODE_1 "M355 S1"
 
+  #define USER_DESC_2 "LED Off" 
+  #define USER_GCODE_2 "M355 S0"
+  
   #define USER_DESC_5 "Home & Info"
   #define USER_GCODE_5 "G28\nM503"
 #endif