diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 5152dc9532..783b6da76c 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -1490,56 +1490,13 @@ void process_commands()
 
 
             // prob 1
-            do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], Z_RAISE_BEFORE_PROBING);
-            do_blocking_move_to(LEFT_PROBE_BED_POSITION - X_PROBE_OFFSET_FROM_EXTRUDER, BACK_PROBE_BED_POSITION - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]);
-
-            engage_z_probe();   // Engage Z Servo endstop if available
-            run_z_probe();
-            float z_at_xLeft_yBack = current_position[Z_AXIS];
-            retract_z_probe();
-
-            SERIAL_PROTOCOLPGM("Bed x: ");
-            SERIAL_PROTOCOL(LEFT_PROBE_BED_POSITION);
-            SERIAL_PROTOCOLPGM(" y: ");
-            SERIAL_PROTOCOL(BACK_PROBE_BED_POSITION);
-            SERIAL_PROTOCOLPGM(" z: ");
-            SERIAL_PROTOCOL(current_position[Z_AXIS]);
-            SERIAL_PROTOCOLPGM("\n");
+            float z_at_xLeft_yBack = probe_pt(LEFT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION, Z_RAISE_BEFORE_PROBING);
 
             // prob 2
-            do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS);
-            do_blocking_move_to(LEFT_PROBE_BED_POSITION - X_PROBE_OFFSET_FROM_EXTRUDER, FRONT_PROBE_BED_POSITION - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]);
-
-            engage_z_probe();   // Engage Z Servo endstop if available
-            run_z_probe();
-            float z_at_xLeft_yFront = current_position[Z_AXIS];
-            retract_z_probe();
-
-            SERIAL_PROTOCOLPGM("Bed x: ");
-            SERIAL_PROTOCOL(LEFT_PROBE_BED_POSITION);
-            SERIAL_PROTOCOLPGM(" y: ");
-            SERIAL_PROTOCOL(FRONT_PROBE_BED_POSITION);
-            SERIAL_PROTOCOLPGM(" z: ");
-            SERIAL_PROTOCOL(current_position[Z_AXIS]);
-            SERIAL_PROTOCOLPGM("\n");
+            float z_at_xLeft_yFront = probe_pt(LEFT_PROBE_BED_POSITION, FRONT_PROBE_BED_POSITION, current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS);
 
             // prob 3
-            do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS);
-            // the current position will be updated by the blocking move so the head will not lower on this next call.
-            do_blocking_move_to(RIGHT_PROBE_BED_POSITION - X_PROBE_OFFSET_FROM_EXTRUDER, FRONT_PROBE_BED_POSITION - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]);
-
-            engage_z_probe();   // Engage Z Servo endstop if available
-            run_z_probe();
-            float z_at_xRight_yFront = current_position[Z_AXIS];
-            retract_z_probe(); // Retract Z Servo endstop if available
-
-            SERIAL_PROTOCOLPGM("Bed x: ");
-            SERIAL_PROTOCOL(RIGHT_PROBE_BED_POSITION);
-            SERIAL_PROTOCOLPGM(" y: ");
-            SERIAL_PROTOCOL(FRONT_PROBE_BED_POSITION);
-            SERIAL_PROTOCOLPGM(" z: ");
-            SERIAL_PROTOCOL(current_position[Z_AXIS]);
-            SERIAL_PROTOCOLPGM("\n");
+            float z_at_xRight_yFront = probe_pt(RIGHT_PROBE_BED_POSITION, FRONT_PROBE_BED_POSITION, current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS);
 
             clean_up_after_endstop_move();