Rename LCD conditionals (#19533)

Marlin/Configuration_adv.h

@@ -1106,18 +1106,18 @@
   #define BOOTSCREEN_TIMEOUT 4000        // (ms) Total Duration to display the boot screen(s)
 #endif
 
-#if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && (HAS_GRAPHICAL_LCD || HAS_CHARACTER_LCD)
+#if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && (HAS_MARLINUI_U8GLIB || HAS_MARLINUI_HD44780)
   //#define SHOW_REMAINING_TIME       // Display estimated time to completion
   #if ENABLED(SHOW_REMAINING_TIME)
     //#define USE_M73_REMAINING_TIME  // Use remaining time from M73 command instead of estimation
     //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
   #endif
 
-  #if HAS_GRAPHICAL_LCD
+  #if HAS_MARLINUI_U8GLIB
     //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   #endif
 
-  #if HAS_CHARACTER_LCD
+  #if HAS_MARLINUI_HD44780
     //#define LCD_PROGRESS_BAR            // Show a progress bar on HD44780 LCDs for SD printing
     #if ENABLED(LCD_PROGRESS_BAR)
       #define PROGRESS_BAR_BAR_TIME 2000  // (ms) Amount of time to show the bar
@@ -1328,7 +1328,7 @@
  * controller events, as there is a trade-off between reliable
  * printing performance versus fast display updates.
  */
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   // Show SD percentage next to the progress bar
   //#define DOGM_SD_PERCENT
 
@@ -1398,7 +1398,7 @@
   //#define MARLIN_SNAKE
   //#define GAMES_EASTER_EGG          // Add extra blank lines above the "Games" sub-menu
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 //
 // Additional options for DGUS / DWIN displays

Marlin/src/HAL/AVR/u8g_com_HAL_AVR_sw_spi.cpp

@@ -57,7 +57,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "../shared/Marduino.h"
 #include "../shared/Delay.h"
@@ -189,5 +189,5 @@ uint8_t u8g_com_HAL_AVR_sw_sp_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp

@@ -59,7 +59,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include <U8glib.h>
 
@@ -145,6 +145,6 @@ uint8_t u8g_com_HAL_DUE_shared_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 #endif // __SAM3X8E__

Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp

@@ -57,7 +57,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD && DISABLED(U8GLIB_ST7920)
+#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920)
 
 #undef SPI_SPEED
 #define SPI_SPEED 2  // About 2 MHz
@@ -144,5 +144,5 @@ uint8_t u8g_com_HAL_DUE_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD && !U8GLIB_ST7920
+#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.cpp

@@ -57,7 +57,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "../../shared/Delay.h"
 
@@ -108,5 +108,5 @@ void u8g_spiSend_sw_DUE_mode_3(uint8_t val) { // 3.5MHz
   }
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/LINUX/spi_pins.h

@@ -24,7 +24,7 @@
 #include "../../core/macros.h"
 #include "../../inc/MarlinConfigPre.h"
 
-#if BOTH(HAS_GRAPHICAL_LCD, SDSUPPORT) && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN)
+#if BOTH(HAS_MARLINUI_U8GLIB, SDSUPPORT) && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN)
   #define LPC_SOFTWARE_SPI  // If the SD card and LCD adapter share the same SPI pins, then software SPI is currently
                             // needed due to the speed and mode required for communicating with each device being different.
                             // This requirement can be removed if the SPI access to these devices is updated to use

Marlin/src/HAL/LPC1768/inc/SanityCheck.h

@@ -113,7 +113,7 @@ static_assert(DISABLED(BAUD_RATE_GCODE), "BAUD_RATE_GCODE is not yet supported o
   #define _IS_RX1_1 IS_RX1
   #if IS_TX1(TMC_SW_SCK)
     #error "Serial port pins (1) conflict with other pins!"
-  #elif HAS_SPI_LCD
+  #elif HAS_WIRED_LCD
     #if IS_TX1(BTN_EN2) || IS_RX1(BTN_EN1)
       #error "Serial port pins (1) conflict with Encoder Buttons!"
     #elif ANY_TX(1, SCK_PIN, LCD_PINS_D4, DOGLCD_SCK, LCD_RESET_PIN, LCD_PINS_RS, SHIFT_CLK) \

Marlin/src/HAL/LPC1768/spi_pins.h

@@ -23,7 +23,7 @@
 
 #include "../../core/macros.h"
 
-#if BOTH(SDSUPPORT, HAS_GRAPHICAL_LCD) && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN)
+#if BOTH(SDSUPPORT, HAS_MARLINUI_U8GLIB) && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN)
   #define LPC_SOFTWARE_SPI  // If the SD card and LCD adapter share the same SPI pins, then software SPI is currently
                             // needed due to the speed and mode required for communicating with each device being different.
                             // This requirement can be removed if the SPI access to these devices is updated to use

Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_hw_spi.cpp

@@ -57,7 +57,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include <U8glib.h>
 #include "../../shared/HAL_SPI.h"
@@ -124,6 +124,6 @@ uint8_t u8g_com_HAL_LPC1768_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 #endif // TARGET_LPC1768

Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_ssd_hw_i2c.cpp

@@ -77,7 +77,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include <U8glib.h>
 
@@ -193,6 +193,6 @@ uint8_t u8g_com_HAL_LPC1768_ssd_hw_i2c_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_v
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 #endif // TARGET_LPC1768

Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp

@@ -57,7 +57,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include <U8glib.h>
 #include "../../shared/HAL_SPI.h"
@@ -133,6 +133,6 @@ uint8_t u8g_com_HAL_LPC1768_ST7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t ar
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 #endif // TARGET_LPC1768

Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp

@@ -57,7 +57,7 @@
 
 #include "../../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD && DISABLED(U8GLIB_ST7920)
+#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920)
 
 #include <SoftwareSPI.h>
 
@@ -203,5 +203,5 @@ uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD && !U8GLIB_ST7920
+#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920
 #endif // TARGET_LPC1768

Marlin/src/HAL/STM32F1/dogm/u8g_com_stm32duino_swspi.cpp

@@ -20,7 +20,7 @@
 
 #include "../../../inc/MarlinConfig.h"
 
-#if BOTH(HAS_GRAPHICAL_LCD, FORCE_SOFT_SPI)
+#if BOTH(HAS_MARLINUI_U8GLIB, FORCE_SOFT_SPI)
 
 #include "../HAL.h"
 #include <U8glib.h>
@@ -161,5 +161,5 @@ uint8_t u8g_com_HAL_STM32F1_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 #endif // STM32F1

Marlin/src/HAL/shared/HAL_ST7920.h

@@ -27,7 +27,7 @@
  * (bypassing U8G), it will allow the LIGHTWEIGHT_UI to operate.
  */
 
-#if BOTH(HAS_GRAPHICAL_LCD, LIGHTWEIGHT_UI)
+#if BOTH(HAS_MARLINUI_U8GLIB, LIGHTWEIGHT_UI)
   void ST7920_cs();
   void ST7920_ncs();
   void ST7920_set_cmd();

Marlin/src/MarlinCore.cpp

@@ -1072,7 +1072,7 @@ void setup() {
     DWIN_UpdateLCD();     // Show bootscreen (first image)
   #else
     SETUP_RUN(ui.init());
-    #if HAS_SPI_LCD && ENABLED(SHOW_BOOTSCREEN)
+    #if HAS_WIRED_LCD && ENABLED(SHOW_BOOTSCREEN)
       SETUP_RUN(ui.show_bootscreen());
     #endif
     SETUP_RUN(ui.reset_status());     // Load welcome message early. (Retained if no errors exist.)

Marlin/src/core/language.h

@@ -303,7 +303,7 @@
 #define LCD_STR_C STR_C
 #define LCD_STR_E STR_E
 
-#if HAS_CHARACTER_LCD
+#if HAS_MARLINUI_HD44780
 
   // Custom characters defined in the first 8 characters of the LCD
   #define LCD_STR_BEDTEMP     "\x00" // Print only as a char. This will have 'unexpected' results when used in a string!

Marlin/src/feature/power_monitor.cpp

@@ -44,7 +44,7 @@ uint8_t PowerMonitor::display_item;
 
 PowerMonitor power_monitor; // Single instance - this calls the constructor
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
   #if ENABLED(POWER_MONITOR_CURRENT)
     void PowerMonitor::draw_current() {
@@ -70,6 +70,6 @@ PowerMonitor power_monitor; // Single instance - this calls the constructor
     }
   #endif
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 #endif // HAS_POWER_MONITOR

Marlin/src/feature/power_monitor.h

@@ -88,8 +88,8 @@ public:
     FORCE_INLINE static float getPower() { return getAmps() * getVolts(); }
   #endif
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
-    #if HAS_GRAPHICAL_LCD && DISABLED(LIGHTWEIGHT_UI)
+    #if HAS_MARLINUI_U8GLIB && DISABLED(LIGHTWEIGHT_UI)
       FORCE_INLINE static bool display_enabled() { return flags != 0x00; }
     #endif
     #if ENABLED(POWER_MONITOR_CURRENT)

Marlin/src/gcode/bedlevel/G26.cpp

@@ -359,7 +359,7 @@ inline bool turn_on_heaters() {
   #if HAS_HEATED_BED
 
     if (g26_bed_temp > 25) {
-      #if HAS_SPI_LCD
+      #if HAS_WIRED_LCD
         ui.set_status_P(GET_TEXT(MSG_G26_HEATING_BED), 99);
         ui.quick_feedback();
         TERN_(HAS_LCD_MENU, ui.capture());
@@ -378,7 +378,7 @@ inline bool turn_on_heaters() {
   #endif // HAS_HEATED_BED
 
   // Start heating the active nozzle
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     ui.set_status_P(GET_TEXT(MSG_G26_HEATING_NOZZLE), 99);
     ui.quick_feedback();
   #endif
@@ -391,7 +391,7 @@ inline bool turn_on_heaters() {
     #endif
   )) return G26_ERR;
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     ui.reset_status();
     ui.quick_feedback();
   #endif
@@ -446,7 +446,7 @@ inline bool prime_nozzle() {
     else
   #endif
   {
-    #if HAS_SPI_LCD
+    #if HAS_WIRED_LCD
       ui.set_status_P(GET_TEXT(MSG_G26_FIXED_LENGTH), 99);
       ui.quick_feedback();
     #endif

Marlin/src/gcode/calibrate/M48.cpp

@@ -144,7 +144,7 @@ void GcodeSuite::M48() {
     float sample_sum = 0.0;
 
     LOOP_L_N(n, n_samples) {
-      #if HAS_SPI_LCD
+      #if HAS_WIRED_LCD
         // Display M48 progress in the status bar
         ui.status_printf_P(0, PSTR(S_FMT ": %d/%d"), GET_TEXT(MSG_M48_POINT), int(n + 1), int(n_samples));
       #endif
@@ -258,7 +258,7 @@ void GcodeSuite::M48() {
     SERIAL_ECHOLNPGM("Finished!");
     dev_report(verbose_level > 0, mean, sigma, min, max, true);
 
-    #if HAS_SPI_LCD
+    #if HAS_WIRED_LCD
       // Display M48 results in the status bar
       char sigma_str[8];
       ui.status_printf_P(0, PSTR(S_FMT ": %s"), GET_TEXT(MSG_M48_DEVIATION), dtostrf(sigma, 2, 6, sigma_str));

Marlin/src/gcode/feature/power_monitor/M430.cpp

@@ -38,7 +38,7 @@
  */
 void GcodeSuite::M430() {
   bool do_report = true;
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     #if ENABLED(POWER_MONITOR_CURRENT)
       if (parser.seen('I')) { power_monitor.set_current_display(parser.value_bool()); do_report = false; }
     #endif

Marlin/src/inc/Conditionals_LCD.h

@@ -456,11 +456,11 @@
 #endif
 
 #if ENABLED(ULTRA_LCD)
-  #define HAS_SPI_LCD 1
+  #define HAS_WIRED_LCD 1
   #if ENABLED(DOGLCD)
-    #define HAS_GRAPHICAL_LCD 1
+    #define HAS_MARLINUI_U8GLIB 1
   #elif DISABLED(HAS_GRAPHICAL_TFT)
-    #define HAS_CHARACTER_LCD 1
+    #define HAS_MARLINUI_HD44780 1
   #endif
 #endif
 
@@ -471,7 +471,7 @@
   #define HAS_ADC_BUTTONS 1
 #endif
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   #ifndef LCD_PIXEL_WIDTH
     #define LCD_PIXEL_WIDTH 128
   #endif

Marlin/src/inc/Conditionals_post.h

@@ -313,7 +313,7 @@
 #elif ENABLED(MAKRPANEL)
   #define _LCD_CONTRAST_INIT  17
 #elif ENABLED(MINIPANEL)
-  #define _LCD_CONTRAST_INIT  150
+  #define _LCD_CONTRAST_INIT 150
 #elif ENABLED(ZONESTAR_12864OLED)
   #define _LCD_CONTRAST_MIN   64
   #define _LCD_CONTRAST_INIT 128
@@ -2455,7 +2455,7 @@
  */
 #if PIN_EXISTS(BEEPER) || EITHER(LCD_USE_I2C_BUZZER, PCA9632_BUZZER)
   #define HAS_BUZZER 1
-  #if NONE(LCD_USE_I2C_BUZZER, PCA9632_BUZZER)
+  #if PIN_EXISTS(BEEPER)
     #define USE_BEEPER 1
   #endif
 #endif
@@ -2483,7 +2483,7 @@
 /**
  * Make sure DOGLCD_SCK and DOGLCD_MOSI are defined.
  */
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   #ifndef DOGLCD_SCK
     #define DOGLCD_SCK  SCK_PIN
   #endif
@@ -2604,17 +2604,17 @@
   #define HAS_FOLDER_SORTING 1
 #endif
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   // Get LCD character width/height, which may be overridden by pins, configs, etc.
   #ifndef LCD_WIDTH
-    #if HAS_GRAPHICAL_LCD
+    #if HAS_MARLINUI_U8GLIB
       #define LCD_WIDTH 21
     #else
       #define LCD_WIDTH TERN(ULTIPANEL, 20, 16)
     #endif
   #endif
   #ifndef LCD_HEIGHT
-    #if HAS_GRAPHICAL_LCD
+    #if HAS_MARLINUI_U8GLIB
       #define LCD_HEIGHT 5
     #else
       #define LCD_HEIGHT TERN(ULTIPANEL, 4, 2)

Marlin/src/inc/SanityCheck.h

@@ -680,7 +680,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
  * LCD Info Screen Style
  */
 #if LCD_INFO_SCREEN_STYLE > 0
-  #if HAS_GRAPHICAL_LCD || LCD_WIDTH < 20 || LCD_HEIGHT < 4
+  #if HAS_MARLINUI_U8GLIB || LCD_WIDTH < 20 || LCD_HEIGHT < 4
     #error "Alternative LCD_INFO_SCREEN_STYLE requires 20x4 Character LCD."
   #elif LCD_INFO_SCREEN_STYLE > 1
     #error "LCD_INFO_SCREEN_STYLE only has options 0 and 1 at this time."
@@ -693,16 +693,16 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 #if ENABLED(LCD_PROGRESS_BAR)
   #if NONE(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
     #error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY."
-  #elif !HAS_CHARACTER_LCD
+  #elif !HAS_MARLINUI_HD44780
     #error "LCD_PROGRESS_BAR requires a character LCD."
-  #elif HAS_GRAPHICAL_LCD
+  #elif HAS_MARLINUI_U8GLIB
     #error "LCD_PROGRESS_BAR does not apply to graphical displays."
   #elif ENABLED(FILAMENT_LCD_DISPLAY)
     #error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
   #elif PROGRESS_MSG_EXPIRE < 0
     #error "PROGRESS_MSG_EXPIRE must be greater than or equal to 0."
   #endif
-#elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && NONE(HAS_GRAPHICAL_LCD, HAS_GRAPHICAL_TFT, HAS_CHARACTER_LCD, EXTENSIBLE_UI)
+#elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && NONE(HAS_MARLINUI_U8GLIB, HAS_GRAPHICAL_TFT, HAS_MARLINUI_HD44780, EXTENSIBLE_UI)
   #error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR, Character LCD, Graphical LCD, TFT, or EXTENSIBLE_UI."
 #endif
 
@@ -713,9 +713,9 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * Custom Boot and Status screens
  */
-#if ENABLED(SHOW_CUSTOM_BOOTSCREEN) && NONE(HAS_GRAPHICAL_LCD, TOUCH_UI_FTDI_EVE)
+#if ENABLED(SHOW_CUSTOM_BOOTSCREEN) && NONE(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE)
   #error "SHOW_CUSTOM_BOOTSCREEN requires Graphical LCD or TOUCH_UI_FTDI_EVE."
-#elif ENABLED(CUSTOM_STATUS_SCREEN_IMAGE) && !HAS_GRAPHICAL_LCD
+#elif ENABLED(CUSTOM_STATUS_SCREEN_IMAGE) && !HAS_MARLINUI_U8GLIB
   #error "CUSTOM_STATUS_SCREEN_IMAGE requires a Graphical LCD."
 #endif
 
@@ -782,7 +782,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
     #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
   #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE
     #error "BABYSTEP_ZPROBE_OFFSET requires a probe."
-  #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !HAS_GRAPHICAL_LCD
+  #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !HAS_MARLINUI_U8GLIB
     #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD."
   #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET)
     #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET."
@@ -1143,7 +1143,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 /**
  * Required LCD language
  */
-#if HAS_CHARACTER_LCD && !defined(DISPLAY_CHARSET_HD44780)
+#if HAS_MARLINUI_HD44780 && !defined(DISPLAY_CHARSET_HD44780)
   #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
 #endif
 
@@ -1465,7 +1465,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
   #endif
 #endif
 
-#if ENABLED(MESH_EDIT_GFX_OVERLAY) && !BOTH(AUTO_BED_LEVELING_UBL, HAS_GRAPHICAL_LCD)
+#if ENABLED(MESH_EDIT_GFX_OVERLAY) && !BOTH(AUTO_BED_LEVELING_UBL, HAS_MARLINUI_U8GLIB)
   #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD."
 #endif
 
@@ -3081,7 +3081,7 @@ static_assert(   _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
   #undef _PIN_CONFLICT
 #endif
 
-#if !HAS_GRAPHICAL_LCD
+#if !HAS_MARLINUI_U8GLIB
   #if ENABLED(PRINT_PROGRESS_SHOW_DECIMALS)
     #error "PRINT_PROGRESS_SHOW_DECIMALS currently requires a Graphical LCD."
   #endif

Marlin/src/lcd/HD44780/lcdprint_hd44780.cpp

@@ -14,7 +14,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_CHARACTER_LCD
+#if HAS_MARLINUI_HD44780
 
 #include "../ultralcd.h"
 #include "../../MarlinCore.h"
@@ -1119,4 +1119,4 @@ int lcd_put_u8str_max_P(PGM_P utf8_str_P, pixel_len_t max_length) {
 
 #endif // DEBUG_LCDPRINT
 
-#endif // HAS_CHARACTER_LCD
+#endif // HAS_MARLINUI_HD44780

Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp

@@ -22,7 +22,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_CHARACTER_LCD
+#if HAS_MARLINUI_HD44780
 
 /**
  * ultralcd_HD44780.cpp
@@ -1517,4 +1517,4 @@ void MarlinUI::draw_status_screen() {
 
 #endif // HAS_LCD_MENU
 
-#endif // HAS_CHARACTER_LCD
+#endif // HAS_MARLINUI_HD44780

Marlin/src/lcd/dogm/lcdprint_u8g.cpp

@@ -9,7 +9,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "ultralcd_DOGM.h"
 
@@ -53,4 +53,4 @@ int lcd_put_u8str_max_P(PGM_P utf8_str_P, pixel_len_t max_length) {
   return ret;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/dogm/status_screen_DOGM.cpp

@@ -27,7 +27,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD && DISABLED(LIGHTWEIGHT_UI)
+#if HAS_MARLINUI_U8GLIB && DISABLED(LIGHTWEIGHT_UI)
 
 #include "dogm_Statusscreen.h"
 #include "ultralcd_DOGM.h"
@@ -913,4 +913,4 @@ void MarlinUI::draw_status_message(const bool blink) {
   #endif
 }
 
-#endif // HAS_GRAPHICAL_LCD && !LIGHTWEIGHT_UI
+#endif // HAS_MARLINUI_U8GLIB && !LIGHTWEIGHT_UI

Marlin/src/lcd/dogm/u8g_dev_ssd1306_sh1106_128x64_I2C.cpp

@@ -67,7 +67,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "HAL_LCD_com_defines.h"
 
@@ -300,4 +300,4 @@ uint8_t u8g_WriteEscSeqP_2_wire(u8g_t *u8g, u8g_dev_t *dev, const uint8_t *esc_s
   return 1;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp

@@ -55,7 +55,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include <U8glib.h>
 #include "HAL_LCD_com_defines.h"
@@ -233,4 +233,4 @@ u8g_dev_t u8g_dev_st7565_64128n_HAL_2x_sw_spi = { u8g_dev_st7565_64128n_HAL_2x_f
 U8G_PB_DEV(u8g_dev_st7565_64128n_HAL_hw_spi, WIDTH, HEIGHT, PAGE_HEIGHT, u8g_dev_st7565_64128n_HAL_fn, U8G_COM_HAL_HW_SPI_FN);
 u8g_dev_t u8g_dev_st7565_64128n_HAL_2x_hw_spi = { u8g_dev_st7565_64128n_HAL_2x_fn, &u8g_dev_st7565_64128n_HAL_2x_pb, U8G_COM_HAL_HW_SPI_FN };
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/dogm/u8g_dev_st7920_128x64_HAL.cpp

@@ -55,7 +55,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "HAL_LCD_com_defines.h"
 
@@ -205,4 +205,4 @@ u8g_dev_t u8g_dev_st7920_128x64_HAL_4x_hw_spi = { u8g_dev_st7920_128x64_HAL_4x_f
   u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = { u8g_dev_st7920_128x64_HAL_4x_fn, &u8g_dev_st7920_128x64_HAL_4x_pb, U8G_COM_ST7920_HAL_SW_SPI };
 #endif
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp

@@ -56,7 +56,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if HAS_GRAPHICAL_LCD && (PIN_EXISTS(FSMC_CS) || ENABLED(SPI_GRAPHICAL_TFT))
+#if HAS_MARLINUI_U8GLIB && (PIN_EXISTS(FSMC_CS) || ENABLED(SPI_GRAPHICAL_TFT))
 
 #include "HAL_LCD_com_defines.h"
 #include "ultralcd_DOGM.h"
@@ -813,4 +813,4 @@ uint8_t u8g_com_hal_tft_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_p
 
 U8G_PB_DEV(u8g_dev_tft_320x240_upscale_from_128x64, WIDTH, HEIGHT, PAGE_HEIGHT, u8g_dev_tft_320x240_upscale_from_128x64_fn, U8G_COM_HAL_TFT_FN);
 
-#endif // HAS_GRAPHICAL_LCD && FSMC_CS
+#endif // HAS_MARLINUI_U8GLIB && FSMC_CS

Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp

@@ -55,7 +55,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "HAL_LCD_com_defines.h"
 
@@ -210,4 +210,4 @@ u8g_pb_t u8g_dev_uc1701_mini12864_HAL_2x_pb = { {16, HEIGHT, 0, 0, 0},  WIDTH, u
 u8g_dev_t u8g_dev_uc1701_mini12864_HAL_2x_sw_spi = { u8g_dev_uc1701_mini12864_HAL_2x_fn, &u8g_dev_uc1701_mini12864_HAL_2x_pb, U8G_COM_HAL_SW_SPI_FN };
 u8g_dev_t u8g_dev_uc1701_mini12864_HAL_2x_hw_spi = { u8g_dev_uc1701_mini12864_HAL_2x_fn, &u8g_dev_uc1701_mini12864_HAL_2x_pb, U8G_COM_HAL_HW_SPI_FN };
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/dogm/u8g_fontutf8.cpp

@@ -9,7 +9,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include <string.h>
 #include "../fontutils.h"
@@ -312,4 +312,4 @@ int uxg_GetUtf8StrPixelWidthP(u8g_t *pu8g, PGM_P utf8_msg) {
   return data.adv;
 }
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/dogm/ultralcd_DOGM.cpp

@@ -37,7 +37,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
 #include "ultralcd_DOGM.h"
 #include "u8g_fontutf8.h"
@@ -687,4 +687,4 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop
 
 #endif // HAS_LCD_MENU
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB

Marlin/src/lcd/fontutils.cpp

@@ -9,7 +9,7 @@
 
 #include "../inc/MarlinConfig.h"
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #include "ultralcd.h"
   #include "../MarlinCore.h"
 #endif

Marlin/src/lcd/lcdprint.cpp

@@ -26,7 +26,7 @@
 
 #include "../inc/MarlinConfigPre.h"
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
 #include "lcdprint.h"
 
@@ -73,4 +73,4 @@ lcd_uint_t lcd_put_u8str_ind_P(PGM_P const pstr, const int8_t ind, PGM_P const i
   return n;
 }
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/lcd/lcdprint.h

@@ -34,7 +34,7 @@
 
 #include "../inc/MarlinConfig.h"
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
   #include "dogm/u8g_fontutf8.h"
   typedef u8g_uint_t lcd_uint_t;

Marlin/src/lcd/menu/menu.cpp

@@ -213,14 +213,14 @@ void MarlinUI::goto_screen(screenFunc_t screen, const uint16_t encoder/*=0*/, co
     clear_lcd();
 
     // Re-initialize custom characters that may be re-used
-    #if HAS_CHARACTER_LCD
+    #if HAS_MARLINUI_HD44780
       if (TERN1(AUTO_BED_LEVELING_UBL, !ubl.lcd_map_control))
         set_custom_characters(on_status_screen() ? CHARSET_INFO : CHARSET_MENU);
     #endif
 
     refresh(LCDVIEW_CALL_REDRAW_NEXT);
     screen_changed = true;
-    TERN_(HAS_GRAPHICAL_LCD, drawing_screen = false);
+    TERN_(HAS_MARLINUI_U8GLIB, drawing_screen = false);
 
     TERN_(HAS_LCD_MENU, encoder_direction_normal());
 

Marlin/src/lcd/menu/menu.h

@@ -39,7 +39,7 @@ typedef void (*selectFunc_t)();
 #define SS_INVERT  0x02
 #define SS_DEFAULT SS_CENTER
 
-#if HAS_GRAPHICAL_LCD && EITHER(BABYSTEP_ZPROBE_GFX_OVERLAY, MESH_EDIT_GFX_OVERLAY)
+#if HAS_MARLINUI_U8GLIB && EITHER(BABYSTEP_ZPROBE_GFX_OVERLAY, MESH_EDIT_GFX_OVERLAY)
   void _lcd_zoffset_overlay_gfx(const float zvalue);
 #endif
 
@@ -215,7 +215,7 @@ void _lcd_draw_homing();
   void line_to_z(const float &z);
 #endif
 
-#if HAS_GRAPHICAL_LCD && EITHER(BABYSTEP_ZPROBE_GFX_OVERLAY, MESH_EDIT_GFX_OVERLAY)
+#if HAS_MARLINUI_U8GLIB && EITHER(BABYSTEP_ZPROBE_GFX_OVERLAY, MESH_EDIT_GFX_OVERLAY)
   void _lcd_zoffset_overlay_gfx(const float zvalue);
 #endif
 

Marlin/src/lcd/menu/menu_configuration.cpp

@@ -60,7 +60,9 @@ void menu_advanced_settings();
     static int8_t bar_percent = 0;
     if (ui.use_click()) {
       ui.goto_previous_screen();
-      ui.set_custom_characters(CHARSET_MENU);
+      #if HAS_MARLINUI_HD44780
+        ui.set_custom_characters(CHARSET_MENU);
+      #endif
       return;
     }
     bar_percent += (int8_t)ui.encoderPosition;
@@ -73,7 +75,9 @@ void menu_advanced_settings();
 
   void _progress_bar_test() {
     ui.goto_screen(progress_bar_test);
-    ui.set_custom_characters(CHARSET_INFO);
+    #if HAS_MARLINUI_HD44780
+      ui.set_custom_characters(CHARSET_INFO);
+    #endif
   }
 
 #endif // LCD_PROGRESS_BAR_TEST

Marlin/src/lcd/menu/menu_media.cpp

@@ -99,7 +99,7 @@ class MenuItem_sdfolder : public MenuItem_sdbase {
       encoderTopLine = 0;
       ui.encoderPosition = 2 * (ENCODER_STEPS_PER_MENU_ITEM);
       ui.screen_changed = true;
-      TERN_(HAS_GRAPHICAL_LCD, ui.drawing_screen = false);
+      TERN_(HAS_MARLINUI_U8GLIB, ui.drawing_screen = false);
       ui.refresh();
     }
 };
@@ -107,7 +107,7 @@ class MenuItem_sdfolder : public MenuItem_sdbase {
 void menu_media() {
   ui.encoder_direction_menus();
 
-  #if HAS_GRAPHICAL_LCD
+  #if HAS_MARLINUI_U8GLIB
     static uint16_t fileCnt;
     if (ui.first_page) fileCnt = card.get_num_Files();
   #else

Marlin/src/lcd/menu/menu_motion.cpp

@@ -205,7 +205,7 @@ void _menu_move_distance(const AxisEnum axis, const screenFunc_t func, const int
       #if DISABLED(HAS_GRAPHICAL_TFT)
         extern const char NUL_STR[];
         SUBMENU_P(NUL_STR, []{ _goto_manual_move(float(SHORT_MANUAL_Z_MOVE)); });
-        MENU_ITEM_ADDON_START(0 + ENABLED(HAS_CHARACTER_LCD));
+        MENU_ITEM_ADDON_START(0 + ENABLED(HAS_MARLINUI_HD44780));
         lcd_put_u8str(tmp);
         MENU_ITEM_ADDON_END();
       #else

Marlin/src/lcd/menu/menu_tune.cpp

@@ -46,7 +46,7 @@
 
   #include "../../feature/babystep.h"
   #include "../lcdprint.h"
-  #if HAS_GRAPHICAL_LCD
+  #if HAS_MARLINUI_U8GLIB
     #include "../dogm/ultralcd_DOGM.h"
   #endif
 
@@ -68,10 +68,10 @@
       const float spm = planner.steps_to_mm[axis];
       MenuEditItemBase::draw_edit_screen(msg, BABYSTEP_TO_STR(spm * babystep.accum));
       #if ENABLED(BABYSTEP_DISPLAY_TOTAL)
-        const bool in_view = TERN1(HAS_GRAPHICAL_LCD, PAGE_CONTAINS(LCD_PIXEL_HEIGHT - MENU_FONT_HEIGHT, LCD_PIXEL_HEIGHT - 1));
+        const bool in_view = TERN1(HAS_MARLINUI_U8GLIB, PAGE_CONTAINS(LCD_PIXEL_HEIGHT - MENU_FONT_HEIGHT, LCD_PIXEL_HEIGHT - 1));
         if (in_view) {
-          TERN_(HAS_GRAPHICAL_LCD, ui.set_font(FONT_MENU));
+          TERN_(HAS_MARLINUI_U8GLIB, ui.set_font(FONT_MENU));
-          lcd_moveto(0, TERN(HAS_GRAPHICAL_LCD, LCD_PIXEL_HEIGHT - MENU_FONT_DESCENT, LCD_HEIGHT - 1));
+          lcd_moveto(0, TERN(HAS_MARLINUI_U8GLIB, LCD_PIXEL_HEIGHT - MENU_FONT_DESCENT, LCD_HEIGHT - 1));
           lcd_put_u8str_P(GET_TEXT(MSG_BABYSTEP_TOTAL));
           lcd_put_wchar(':');
           lcd_put_u8str(BABYSTEP_TO_STR(spm * babystep.axis_total[BS_TOTAL_IND(axis)]));

Marlin/src/lcd/touch/touch_buttons.cpp

@@ -74,7 +74,7 @@ TouchButtons touch;
 void TouchButtons::init() { touchIO.Init(); }
 
 uint8_t TouchButtons::read_buttons() {
-  #ifdef HAS_SPI_LCD
+  #ifdef HAS_WIRED_LCD
     int16_t x, y;
 
     if (!touchIO.getRawPoint(&x, &y)) return 0;

Marlin/src/lcd/ultralcd.cpp

@@ -51,7 +51,7 @@ MarlinUI ui;
 
 constexpr uint8_t epps = ENCODER_PULSES_PER_STEP;
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #if ENABLED(STATUS_MESSAGE_SCROLLING)
     uint8_t MarlinUI::status_scroll_offset; // = 0
     constexpr uint8_t MAX_MESSAGE_LENGTH = _MAX(LONG_FILENAME_LENGTH, MAX_LANG_CHARSIZE * 2 * (LCD_WIDTH));
@@ -62,7 +62,7 @@ constexpr uint8_t epps = ENCODER_PULSES_PER_STEP;
   constexpr uint8_t MAX_MESSAGE_LENGTH = 63;
 #endif
 
-#if EITHER(HAS_SPI_LCD, EXTENSIBLE_UI)
+#if EITHER(HAS_WIRED_LCD, EXTENSIBLE_UI)
   uint8_t MarlinUI::alert_level; // = 0
   char MarlinUI::status_message[MAX_MESSAGE_LENGTH + 1];
 #endif
@@ -114,9 +114,9 @@ constexpr uint8_t epps = ENCODER_PULSES_PER_STEP;
   }
 #endif
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   #include "dogm/ultralcd_DOGM.h"
 #endif
 
@@ -167,7 +167,7 @@ uint8_t MarlinUI::lcd_status_update_delay = 1; // First update one loop delayed
 
 millis_t MarlinUI::next_button_update_ms; // = 0
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   bool MarlinUI::drawing_screen, MarlinUI::first_page; // = false
 #endif
 
@@ -372,7 +372,7 @@ void MarlinUI::init() {
 
   #endif // HAS_SHIFT_ENCODER
 
-  #if HAS_ENCODER_ACTION && HAS_SLOW_BUTTONS
+  #if BOTH(HAS_ENCODER_ACTION, HAS_SLOW_BUTTONS)
     slow_buttons = 0;
   #endif
 
@@ -873,7 +873,7 @@ void MarlinUI::update() {
 
   #endif // HAS_LCD_MENU
 
-  if (ELAPSED(ms, next_lcd_update_ms) || TERN0(HAS_GRAPHICAL_LCD, drawing_screen)) {
+  if (ELAPSED(ms, next_lcd_update_ms) || TERN0(HAS_MARLINUI_U8GLIB, drawing_screen)) {
 
     next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL;
 
@@ -971,7 +971,7 @@ void MarlinUI::update() {
     // This runs every ~100ms when idling often enough.
     // Instead of tracking changes just redraw the Status Screen once per second.
     if (on_status_screen() && !lcd_status_update_delay--) {
-      lcd_status_update_delay = TERN(HAS_GRAPHICAL_LCD, 12, 9);
+      lcd_status_update_delay = TERN(HAS_MARLINUI_U8GLIB, 12, 9);
       if (max_display_update_time) max_display_update_time--;  // Be sure never go to a very big number
       refresh(LCDVIEW_REDRAW_NOW);
     }
@@ -1010,7 +1010,7 @@ void MarlinUI::update() {
 
       TERN_(HAS_ADC_BUTTONS, keypad_buttons = 0);
 
-      #if HAS_GRAPHICAL_LCD
+      #if HAS_MARLINUI_U8GLIB
 
         #if ENABLED(LIGHTWEIGHT_UI)
           const bool in_status = on_status_screen(),
@@ -1294,7 +1294,7 @@ void MarlinUI::update() {
 
 #endif // HAS_ENCODER_ACTION
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #if HAS_DISPLAY
 
@@ -1342,7 +1342,7 @@ void MarlinUI::update() {
       next_filament_display = ms + 5000UL; // Show status message for 5s
     #endif
 
-    #if BOTH(HAS_SPI_LCD, STATUS_MESSAGE_SCROLLING)
+    #if BOTH(HAS_WIRED_LCD, STATUS_MESSAGE_SCROLLING)
       status_scroll_offset = 0;
     #endif
 
@@ -1501,7 +1501,7 @@ void MarlinUI::update() {
     set_status_P(print_paused);
 
     #if ENABLED(PARK_HEAD_ON_PAUSE)
-      TERN_(HAS_SPI_LCD, lcd_pause_show_message(PAUSE_MESSAGE_PARKING, PAUSE_MODE_PAUSE_PRINT)); // Show message immediately to let user know about pause in progress
+      TERN_(HAS_WIRED_LCD, lcd_pause_show_message(PAUSE_MESSAGE_PARKING, PAUSE_MODE_PAUSE_PRINT)); // Show message immediately to let user know about pause in progress
       queue.inject_P(PSTR("M25 P\nM24"));
     #elif ENABLED(SDSUPPORT)
       queue.inject_P(PSTR("M25"));
@@ -1610,11 +1610,11 @@ void MarlinUI::update() {
 
     refresh();
 
-    #if HAS_SPI_LCD || defined(LED_BACKLIGHT_TIMEOUT)
+    #if HAS_WIRED_LCD || defined(LED_BACKLIGHT_TIMEOUT)
       const millis_t ms = millis();
     #endif
 
-    TERN_(HAS_SPI_LCD, next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL); // Delay LCD update for SD activity
+    TERN_(HAS_WIRED_LCD, next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL); // Delay LCD update for SD activity
 
     #ifdef LED_BACKLIGHT_TIMEOUT
       leds.reset_timeout(ms);

Marlin/src/lcd/ultralcd.h

@@ -40,7 +40,7 @@
 #if HAS_ENCODER_WHEEL || ANY_BUTTON(ENC, BACK, UP, DWN, LFT, RT)
   #define HAS_DIGITAL_BUTTONS 1
 #endif
-#if !HAS_ADC_BUTTONS && (ENABLED(REPRAPWORLD_KEYPAD) || (HAS_SPI_LCD && DISABLED(NEWPANEL)))
+#if !HAS_ADC_BUTTONS && (ENABLED(REPRAPWORLD_KEYPAD) || (HAS_WIRED_LCD && DISABLED(NEWPANEL)))
   #define HAS_SHIFT_ENCODER 1
 #endif
 
@@ -53,7 +53,7 @@
   #define MULTI_MANUAL 1
 #endif
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #include "../MarlinCore.h"
 
@@ -104,7 +104,7 @@
 
   #endif // HAS_LCD_MENU
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 // REPRAPWORLD_KEYPAD (and ADC_KEYPAD)
 #if ENABLED(REPRAPWORLD_KEYPAD)
@@ -231,7 +231,7 @@
   #endif
 #endif
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   enum MarlinFont : uint8_t {
     FONT_STATUSMENU = 1,
     FONT_EDIT,
@@ -316,11 +316,11 @@ public:
     static void refresh();
   #else
     FORCE_INLINE static void refresh() {
-      TERN_(HAS_SPI_LCD, refresh(LCDVIEW_CLEAR_CALL_REDRAW));
+      TERN_(HAS_WIRED_LCD, refresh(LCDVIEW_CLEAR_CALL_REDRAW));
     }
   #endif
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     static bool detected();
     static void init_lcd();
   #else
@@ -381,7 +381,7 @@ public:
     static void pause_print();
     static void resume_print();
 
-    #if HAS_SPI_LCD
+    #if HAS_WIRED_LCD
 
       static millis_t next_button_update_ms;
 
@@ -403,7 +403,7 @@ public:
         static void show_bootscreen();
       #endif
 
-      #if HAS_GRAPHICAL_LCD
+      #if HAS_MARLINUI_U8GLIB
 
         static void set_font(const MarlinFont font_nr);
 
@@ -458,7 +458,7 @@ public:
 
     #endif
 
-    #if HAS_GRAPHICAL_LCD
+    #if HAS_MARLINUI_U8GLIB
       static bool drawing_screen, first_page;
     #else
       static constexpr bool drawing_screen = false, first_page = true;
@@ -577,7 +577,7 @@ public:
 
     static void draw_select_screen_prompt(PGM_P const pref, const char * const string=nullptr, PGM_P const suff=nullptr);
 
-  #elif HAS_SPI_LCD
+  #elif HAS_WIRED_LCD
 
     static constexpr bool lcd_clicked = false;
     static constexpr bool on_status_screen() { return true; }
@@ -692,7 +692,7 @@ private:
     static void finish_status(const bool persist);
   #endif
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     #if HAS_LCD_MENU && LCD_TIMEOUT_TO_STATUS > 0
       static bool defer_return_to_status;
     #else

Marlin/src/module/endstops.cpp

@@ -351,7 +351,7 @@ void Endstops::event_handler() {
   if (hit_state == prev_hit_state) return;
   prev_hit_state = hit_state;
   if (hit_state) {
-    #if HAS_SPI_LCD
+    #if HAS_WIRED_LCD
       char chrX = ' ', chrY = ' ', chrZ = ' ', chrP = ' ';
       #define _SET_STOP_CHAR(A,C) (chr## A = C)
     #else
@@ -382,7 +382,7 @@ void Endstops::event_handler() {
     #endif
     SERIAL_EOL();
 
-    TERN_(HAS_SPI_LCD, ui.status_printf_P(0, PSTR(S_FMT " %c %c %c %c"), GET_TEXT(MSG_LCD_ENDSTOPS), chrX, chrY, chrZ, chrP));
+    TERN_(HAS_WIRED_LCD, ui.status_printf_P(0, PSTR(S_FMT " %c %c %c %c"), GET_TEXT(MSG_LCD_ENDSTOPS), chrX, chrY, chrZ, chrP));
 
     #if BOTH(SD_ABORT_ON_ENDSTOP_HIT, SDSUPPORT)
       if (planner.abort_on_endstop_hit) {

Marlin/src/module/planner.cpp

@@ -234,7 +234,7 @@ float Planner::previous_nominal_speed_sqr;
   xyze_pos_t Planner::position_cart;
 #endif
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   volatile uint32_t Planner::block_buffer_runtime_us = 0;
 #endif
 
@@ -747,7 +747,7 @@ block_t* Planner::get_current_block() {
     if (TEST(block->flag, BLOCK_BIT_RECALCULATE)) return nullptr;
 
     // We can't be sure how long an active block will take, so don't count it.
-    TERN_(HAS_SPI_LCD, block_buffer_runtime_us -= block->segment_time_us);
+    TERN_(HAS_WIRED_LCD, block_buffer_runtime_us -= block->segment_time_us);
 
     // As this block is busy, advance the nonbusy block pointer
     block_buffer_nonbusy = next_block_index(block_buffer_tail);
@@ -761,7 +761,7 @@ block_t* Planner::get_current_block() {
   }
 
   // The queue became empty
-  TERN_(HAS_SPI_LCD, clear_block_buffer_runtime()); // paranoia. Buffer is empty now - so reset accumulated time to zero.
+  TERN_(HAS_WIRED_LCD, clear_block_buffer_runtime()); // paranoia. Buffer is empty now - so reset accumulated time to zero.
 
   return nullptr;
 }
@@ -1578,7 +1578,7 @@ void Planner::quick_stop() {
   // forced to empty, there's no risk the ISR will touch this.
   delay_before_delivering = BLOCK_DELAY_FOR_1ST_MOVE;
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     // Clear the accumulated runtime
     clear_block_buffer_runtime();
   #endif
@@ -2081,7 +2081,7 @@ bool Planner::_populate_block(block_t * const block, bool split_move,
   const uint8_t moves_queued = nonbusy_movesplanned();
 
   // Slow down when the buffer starts to empty, rather than wait at the corner for a buffer refill
-  #if EITHER(SLOWDOWN, HAS_SPI_LCD) || defined(XY_FREQUENCY_LIMIT)
+  #if EITHER(SLOWDOWN, HAS_WIRED_LCD) || defined(XY_FREQUENCY_LIMIT)
     // Segment time im micro seconds
     int32_t segment_time_us = LROUND(1000000.0f / inverse_secs);
   #endif
@@ -2096,14 +2096,14 @@ bool Planner::_populate_block(block_t * const block, bool split_move,
         // Buffer is draining so add extra time. The amount of time added increases if the buffer is still emptied more.
         const int32_t nst = segment_time_us + LROUND(2 * time_diff / moves_queued);
         inverse_secs = 1000000.0f / nst;
-        #if defined(XY_FREQUENCY_LIMIT) || HAS_SPI_LCD
+        #if defined(XY_FREQUENCY_LIMIT) || HAS_WIRED_LCD
           segment_time_us = nst;
         #endif
       }
     }
   #endif
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     // Protect the access to the position.
     const bool was_enabled = stepper.suspend();
 
@@ -3029,7 +3029,7 @@ void Planner::set_max_jerk(const AxisEnum axis, float targetValue) {
   #endif
 }
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   uint16_t Planner::block_buffer_runtime() {
     #ifdef __AVR__

Marlin/src/module/planner.h

@@ -218,7 +218,7 @@ typedef struct block_t {
     uint8_t valve_pressure, e_to_p_pressure;
   #endif
 
-  #if HAS_SPI_LCD
+  #if HAS_WIRED_LCD
     uint32_t segment_time_us;
   #endif
 
@@ -438,7 +438,7 @@ class Planner {
       static uint8_t g_uc_extruder_last_move[EXTRUDERS];
     #endif
 
-    #if HAS_SPI_LCD
+    #if HAS_WIRED_LCD
       volatile static uint32_t block_buffer_runtime_us; // Theoretical block buffer runtime in µs
     #endif
 
@@ -871,7 +871,7 @@ class Planner {
         block_buffer_tail = next_block_index(block_buffer_tail);
     }
 
-    #if HAS_SPI_LCD
+    #if HAS_WIRED_LCD
       static uint16_t block_buffer_runtime();
       static void clear_block_buffer_runtime();
     #endif

Marlin/src/pins/esp32/pins_MRR_ESPE.h

@@ -124,7 +124,7 @@
 // LCDs and Controllers //
 //////////////////////////
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
 
   #define LCD_PINS_RS                         13
   #define LCD_PINS_ENABLE                     17
@@ -152,7 +152,7 @@
   #define BTN_EN2                             12
   #define BTN_ENC                             14
 
-#endif // HAS_GRAPHICAL_LCD
+#endif // HAS_MARLINUI_U8GLIB
 
 // Hardware serial pins
 // Add the following to Configuration.h or Configuration_adv.h to assign

Marlin/src/pins/linux/pins_RAMPS_LINUX.h

@@ -389,7 +389,7 @@
 // LCDs and Controllers //
 //////////////////////////
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   //
   // LCD Display output pins
@@ -632,4 +632,4 @@
     #endif
   #endif // NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h

@@ -126,7 +126,7 @@
  * for the onboard SD card, and a chip select signal is not provided for the remote
  * SD card.
  */
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define BEEPER_PIN                       P1_31  // EXP1-1
 
@@ -139,7 +139,7 @@
   #define LCD_PINS_ENABLE                  P0_18  // (MOSI) EXP1-3
   #define LCD_PINS_D4                      P0_15  // (SCK)  EXP1-5
 
-  #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && HAS_CHARACTER_LCD
+  #if BOTH(HAS_MARLINUI_HD44780, REPRAP_DISCOUNT_SMART_CONTROLLER)
     #error "REPRAP_DISCOUNT_SMART_CONTROLLER is not supported by the BIQU B300 v1.0"
   #endif
 
@@ -147,7 +147,7 @@
     #error "SDSUPPORT is not supported by the BIQU B300 v1.0 when an LCD controller is used"
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 /**
  * SD Card Reader

Marlin/src/pins/lpc1768/pins_BIQU_BQ111_A4.h

@@ -97,7 +97,7 @@
  * for the onboard SD card, and a chip select signal is not provided for the remote
  * SD card.
  */
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define BEEPER_PIN                       P1_31  // EXP1-1
 
@@ -110,7 +110,7 @@
   #define LCD_PINS_ENABLE                  P0_18  // (MOSI) EXP1-3
   #define LCD_PINS_D4                      P0_15  // (SCK)  EXP1-5
 
-  #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && HAS_CHARACTER_LCD
+  #if BOTH(HAS_MARLINUI_HD44780, REPRAP_DISCOUNT_SMART_CONTROLLER)
     #error "REPRAP_DISCOUNT_SMART_CONTROLLER is not supported by the BIQU BQ111-A4"
   #endif
 
@@ -118,7 +118,7 @@
     #error "SDSUPPORT is not supported by the BIQU BQ111-A4 when an LCD controller is used"
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 /**
  * SD Card Reader

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_1.h

@@ -65,7 +65,7 @@
  * by redrawing the screen after SD card accesses.
  */
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define BTN_EN1                          P3_26
   #define BTN_EN2                          P3_25
   #define BTN_ENC                          P2_11

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h

@@ -214,7 +214,7 @@
 #define EXPA2_09_PIN                       P0_15
 #define EXPA2_10_PIN                       P0_17
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ENABLED(ANET_FULL_GRAPHICS_LCD)
 
@@ -350,7 +350,7 @@
 
   #endif // !CR10_STOCKDISPLAY
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // SD Support

Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h

@@ -232,7 +232,7 @@
  *              -----                                             -----
  *              EXP2                                              EXP1
  */
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #if ENABLED(ANET_FULL_GRAPHICS_LCD)
 
     #define LCD_PINS_RS                    P1_23
@@ -371,9 +371,9 @@
 
     #endif // !FYSETC_MINI_12864
 
-  #endif // HAS_GRAPHICAL_LCD
+  #endif // HAS_MARLINUI_U8GLIB
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #if HAS_ADC_BUTTONS
   #error "ADC BUTTONS do not work unmodifed on SKR 1.4, The ADC ports cannot take more than 3.3v."

Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h

@@ -92,7 +92,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define BEEPER_PIN                       P1_30  // (37) not 5V tolerant
 #endif
 

Marlin/src/pins/lpc1768/pins_MKS_SBASE.h

@@ -217,7 +217,7 @@
  * that the garbage/lines are erased immediately after the SD card accesses are completed.
  */
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define BEEPER_PIN                       P1_31  // EXP1.1
   #define BTN_ENC                          P1_30  // EXP1.2
   #define BTN_EN1                          P3_26  // EXP2.5

Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h

@@ -235,7 +235,8 @@
  *                -----                                            -----
  *                EXP1                                             EXP2
  */
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
+
   #define BEEPER_PIN                       P1_31
   #define BTN_ENC                          P1_30
 
@@ -321,7 +322,7 @@
 
   #endif // !CR10_STOCKDISPLAY
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #ifndef SDCARD_CONNECTION
   #define SDCARD_CONNECTION              ONBOARD

Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h

@@ -326,7 +326,7 @@
   #define LCD_PINS_ENABLE                  P0_18  // J3-10 & AUX-3 (SID, MOSI)
   #define LCD_PINS_D4                      P2_06  // J3-8 & AUX-3 (SCK, CLK)
 
-#elif HAS_SPI_LCD
+#elif HAS_WIRED_LCD
 
   //#define SCK_PIN                        P0_15  // (52)  system defined J3-9 & AUX-3
   //#define MISO_PIN                       P0_17  // (50)  system defined J3-10 & AUX-3
@@ -370,8 +370,9 @@
     #define DOGLCD_SCK                   SCK_PIN
     #define DOGLCD_MOSI                 MOSI_PIN
 
-    #define STAT_LED_BLUE_PIN              P0_26  //(63)  may change if cable changes
+    #define STAT_LED_BLUE_PIN              P0_26  // (63)  may change if cable changes
     #define STAT_LED_RED_PIN               P1_21  // ( 6)  may change if cable changes
+
   #else
 
     #if ENABLED(FYSETC_MINI_12864)
@@ -420,9 +421,9 @@
     //#define LCD_SCREEN_ROT_90
     //#define LCD_SCREEN_ROT_180
     //#define LCD_SCREEN_ROT_270
-  #endif
+ #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // Ethernet pins

Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h

@@ -109,7 +109,7 @@
 //
 // Display
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ENABLED(CR10_STOCKDISPLAY)
 
@@ -185,7 +185,7 @@
 
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // SD Support

Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h

@@ -193,7 +193,7 @@
 #define EXPA1_09_PIN                       P0_16
 #define EXPA1_10_PIN                       P2_08
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ENABLED(CR10_STOCKDISPLAY)
 
@@ -238,7 +238,7 @@
 
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // SD Support

Marlin/src/pins/lpc1769/pins_COHESION3D_MINI.h

@@ -141,7 +141,7 @@
 // connector are shared with the onboard SD card, and Marlin does not support reading
 // G-code files from the onboard SD card.
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define BEEPER_PIN                       P0_27  // EXP2-7 - open drain
 
@@ -160,7 +160,7 @@
     #error "SDSUPPORT is not currently supported by the Cohesion3D boards"
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // Ethernet pins

Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h

@@ -206,7 +206,7 @@
     #define NEOPIXEL_PIN                   P1_16  // EXP1-6  =>  Ethernet pin  6 (top row, 3 from left)
   #endif
 
-#elif HAS_SPI_LCD
+#elif HAS_WIRED_LCD
 
   #define BEEPER_PIN                       P1_31  // EXP1-1
   //#define SD_DETECT_PIN                  P0_27  // EXP2-7
@@ -222,7 +222,7 @@
 
   #define KILL_PIN                         P2_11  // EXP2-10
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // SD Support

Marlin/src/pins/lpc1769/pins_MKS_SGEN_L_V2.h

@@ -241,11 +241,12 @@
  *                -----                                            -----
  *                EXP1                                             EXP2
  */
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define BEEPER_PIN                       P1_31
   #define BTN_ENC                          P1_30
 
   #if ENABLED(CR10_STOCKDISPLAY)
+
     #define LCD_PINS_RS                    P1_00
 
     #define BTN_EN1                        P0_18
@@ -327,7 +328,7 @@
 
   #endif // !CR10_STOCKDISPLAY
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #ifndef SDCARD_CONNECTION
   #define SDCARD_CONNECTION              ONBOARD

Marlin/src/pins/lpc1769/pins_SMOOTHIEBOARD.h

@@ -109,7 +109,7 @@
   #define STAT_LED_RED_PIN                 P1_19
   #define STAT_LED_BLUE_PIN                P1_20
 
-#elif HAS_SPI_LCD
+#elif HAS_WIRED_LCD
 
   /*
     The Smoothieboard supports the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER with either

Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h

@@ -178,6 +178,6 @@
   #define LCD_PINS_ENABLE                  P0_18
   #define LCD_PINS_D4                      P0_15
   #define KILL_PIN                         P2_11
-#elif HAS_SPI_LCD
+#elif HAS_WIRED_LCD
   #error "Only the CR10_STOCKDISPLAY is supported with TH3D EZBoard."
 #endif

Marlin/src/pins/mega/pins_GT2560_REV_A.h

@@ -105,7 +105,7 @@
 #define SUICIDE_PIN                           54  // Must be enabled at startup to keep power flowing
 #define KILL_PIN                              -1
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define BEEPER_PIN                          18
 
@@ -148,4 +148,4 @@
 
   #endif // !NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/mega/pins_HJC2560C_REV2.h

@@ -123,7 +123,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define BEEPER_PIN                          18
 
@@ -170,4 +170,4 @@
 
   #endif // !NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/mega/pins_INTAMSYS40.h

@@ -122,7 +122,7 @@
 
 #define BEEPER_PIN                            18
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define LCD_PINS_RS                         20
   #define LCD_PINS_ENABLE                     30
   #define LCD_PINS_D4                         14

Marlin/src/pins/mega/pins_MEGATRONICS_2.h

@@ -130,7 +130,7 @@
 //
 #define BEEPER_PIN                            64
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define LCD_PINS_RS                         14
   #define LCD_PINS_ENABLE                     15
@@ -152,4 +152,4 @@
     #define SHIFT_EN                          17
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h

@@ -212,7 +212,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
 
@@ -260,7 +260,7 @@
   #define BTN_CENTER                          15  // J0
   #define BTN_ENC                     BTN_CENTER
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // SD Card

Marlin/src/pins/mega/pins_OVERLORD.h

@@ -119,7 +119,7 @@
 //
 // LCD / Controller
 //
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   // OVERLORD OLED pins
   #define LCD_PINS_RS                         20
   #define LCD_PINS_D5                         21

Marlin/src/pins/mega/pins_PICA.h

@@ -137,7 +137,7 @@
 //
 #define BEEPER_PIN                            29
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define LCD_PINS_RS                         33
   #define LCD_PINS_ENABLE                     30
   #define LCD_PINS_D4                         35

Marlin/src/pins/mega/pins_SILVER_GATE.h

@@ -72,7 +72,7 @@
 #define HEATER_BED_PIN                         8
 #define TEMP_BED_PIN                           6
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   #if ENABLED(U8GLIB_ST7920)                      // SPI GLCD 12864 ST7920
     #define LCD_PINS_RS                       30
     #define LCD_PINS_ENABLE                   20

Marlin/src/pins/pins.h

@@ -1227,7 +1227,7 @@
   #define LCD_PINS_D4 -1
 #endif
 
-#if HAS_CHARACTER_LCD || TOUCH_UI_ULTIPANEL
+#if HAS_MARLINUI_HD44780 || TOUCH_UI_ULTIPANEL
   #ifndef LCD_PINS_D5
     #define LCD_PINS_D5 -1
   #endif
@@ -1597,7 +1597,7 @@
   #define Z4_MS3_PIN -1
 #endif
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   #if !defined(ST7920_DELAY_1) && defined(BOARD_ST7920_DELAY_1)
     #define ST7920_DELAY_1 BOARD_ST7920_DELAY_1
   #endif

Marlin/src/pins/rambo/pins_EINSY_RAMBO.h

@@ -160,7 +160,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD || TOUCH_UI_ULTIPANEL
+#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL
 
   #define KILL_PIN                            32
 
@@ -188,4 +188,4 @@
     #define SD_DETECT_PIN                     15
 
   #endif // ULTIPANEL || TOUCH_UI_ULTIPANEL
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/rambo/pins_EINSY_RETRO.h

@@ -166,7 +166,7 @@
 //
 // LCD / Controller
 //
-#if ANY(HAS_SPI_LCD, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE)
+#if ANY(HAS_WIRED_LCD, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE)
 
   #define KILL_PIN                            32
 
@@ -196,4 +196,4 @@
 
   #endif // ULTIPANEL || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE
 
-#endif // HAS_SPI_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE
+#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE

Marlin/src/pins/rambo/pins_MINIRAMBO.h

@@ -141,7 +141,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD || TOUCH_UI_ULTIPANEL
+#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL
 
   #if !MB(MINIRAMBO_10A)
     #define KILL_PIN                          32
@@ -189,4 +189,4 @@
 
   #endif // ULTIPANEL || TOUCH_UI_ULTIPANEL
 
-#endif // HAS_SPI_LCD || TOUCH_UI_ULTIPANEL
+#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL

Marlin/src/pins/rambo/pins_RAMBO.h

@@ -183,7 +183,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD || TOUCH_UI_ULTIPANEL
+#if HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL
 
   #define KILL_PIN                            80
 
@@ -249,4 +249,4 @@
 
   #endif // !NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/ramps/pins_3DRAG.h

@@ -106,7 +106,7 @@
 
   #define BEEPER_PIN                          33
 
-#endif // HAS_SPI_LCD && NEWPANEL
+#endif // ULTRA_LCD && NEWPANEL
 
 /**
  *  M3/M4/M5 - Spindle/Laser Control

Marlin/src/pins/ramps/pins_DUPLICATOR_I3_PLUS.h

@@ -87,7 +87,7 @@
 //
 // LCDs and Controllers
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #if ENABLED(ZONESTAR_LCD)
     #define LCD_PINS_RS                        2
     #define LCD_PINS_ENABLE                   36

Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h

@@ -197,7 +197,7 @@
   #define LCD_PINS_D7                         29
 #endif
 
-#if HAS_GRAPHICAL_LCD
+#if HAS_MARLINUI_U8GLIB
   #ifndef BOARD_ST7920_DELAY_1
     #define BOARD_ST7920_DELAY_1 DELAY_NS(200)
   #endif

Marlin/src/pins/ramps/pins_FYSETC_F6_13.h

@@ -261,7 +261,7 @@
       #define NEOPIXEL_PIN                    25
     #endif
 
-  #elif HAS_GRAPHICAL_LCD
+  #elif HAS_MARLINUI_U8GLIB
 
     #define LCD_PINS_RS                       16
     #define LCD_PINS_ENABLE                   17

Marlin/src/pins/ramps/pins_K8800.h

@@ -95,7 +95,7 @@
 //
 #define BEEPER_PIN                             6
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define LCD_SDSS                            53
 
@@ -119,4 +119,4 @@
     #define BTN_ENC                           23
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/ramps/pins_RAMPS.h

@@ -430,7 +430,7 @@
 // LCDs and Controllers //
 //////////////////////////
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   //
   // LCD Display output pins
@@ -706,7 +706,7 @@
     #endif
   #endif // NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(ADC_KEYPAD)
   #define SHIFT_OUT                           40

Marlin/src/pins/ramps/pins_TRIGORILLA_14.h

@@ -128,7 +128,7 @@
 // AnyCubic made the following changes to 1.1.0-RC8
 // If these are appropriate for your LCD let us know.
 //
-#if 0 && HAS_SPI_LCD
+#if 0 && HAS_WIRED_LCD
 
   // LCD Display output pins
   #if BOTH(NEWPANEL, PANEL_ONE)
@@ -154,4 +154,4 @@
     #define DOGLCD_A0                         42
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/ramps/pins_TT_OSCAR.h

@@ -271,7 +271,7 @@
 // LCDs and Controllers //
 //////////////////////////
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   //
   // LCD Display output pins

Marlin/src/pins/ramps/pins_ULTIMAKER.h

@@ -119,7 +119,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define BEEPER_PIN                          18
 
@@ -158,7 +158,7 @@
 
   #endif // !NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // M3/M4/M5 - Spindle/Laser Control

Marlin/src/pins/sam/pins_ARCHIM1.h

@@ -181,7 +181,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   #define BEEPER_PIN                          23  // D24 PA15_CTS1
   #define LCD_PINS_RS                         17  // D17 PA12_RXD1
   #define LCD_PINS_ENABLE                     24  // D23 PA14_RTS1
@@ -198,4 +198,4 @@
     #define BTN_EN2                           13  // D13 PB27_TIOB0
     #define BTN_ENC                           16  // D16 PA13_TXD1
   #endif // NEWPANEL
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/sam/pins_ARCHIM2.h

@@ -237,7 +237,7 @@
 //
 // LCD / Controller
 //
-#if ANY(HAS_SPI_LCD, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE)
+#if ANY(HAS_WIRED_LCD, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE)
   #define BEEPER_PIN                          23  // D24 PA15_CTS1
   #define LCD_PINS_RS                         17  // D17 PA12_RXD1
   #define LCD_PINS_ENABLE                     24  // D23 PA14_RTS1

Marlin/src/pins/sam/pins_DUE3DOM.h

@@ -113,7 +113,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define LCD_PINS_RS                         42
   #define LCD_PINS_ENABLE                     43
@@ -168,4 +168,4 @@
 
     #define BEEPER_PIN                        -1
   #endif // SPARK_FULL_GRAPHICS
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/sam/pins_DUE3DOM_MINI.h

@@ -105,7 +105,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #define LCD_PINS_RS                         42
   #define LCD_PINS_ENABLE                     43
@@ -171,4 +171,4 @@
     #define DOGLCD_CS                         45
 
   #endif // SPARK_FULL_GRAPHICS
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/sam/pins_RADDS.h

@@ -226,7 +226,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ENABLED(RADDS_DISPLAY)
 
@@ -287,7 +287,7 @@
 
   #endif // SPARK_FULL_GRAPHICS
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #ifndef SDSS
   #define SDSS                                 4

Marlin/src/pins/sam/pins_RAMPS_DUO.h

@@ -76,7 +76,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if BOTH(NEWPANEL, PANEL_ONE)
     #undef LCD_PINS_D4
@@ -129,4 +129,4 @@
 
   #endif // NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/sam/pins_RAMPS_FD_V1.h

@@ -139,7 +139,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
   // ramps-fd lcd adaptor
 
   #define BEEPER_PIN                          37
@@ -203,7 +203,7 @@
     #define DOGLCD_MISO                       74  // MISO_PIN
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 #if HAS_TMC_UART
   /**

Marlin/src/pins/sam/pins_RURAMPS4D_11.h

@@ -200,7 +200,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
     #define BEEPER_PIN                        62
@@ -271,4 +271,4 @@
     #define BTN_ENC                           40
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/sam/pins_RURAMPS4D_13.h

@@ -186,7 +186,7 @@
 //
 // LCD / Controller
 //
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
     #define BEEPER_PIN                        62
@@ -253,4 +253,4 @@
     #define BTN_ENC                           40
   #endif
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD

Marlin/src/pins/samd/pins_RAMPS_144.h

@@ -287,7 +287,7 @@
 // LCDs and Controllers //
 //////////////////////////
 
-#if HAS_SPI_LCD
+#if HAS_WIRED_LCD
 
   //
   // LCD Display output pins
@@ -594,7 +594,7 @@
     #endif
   #endif // NEWPANEL
 
-#endif // HAS_SPI_LCD
+#endif // HAS_WIRED_LCD
 
 //
 // SD Support