From bc06406d7db570f3cff96d7bae811bb87ec03a67 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Hannes=20Brandst=C3=A4tter-M=C3=BCller?= Date: Sun, 16 Sep 2018 06:27:21 +0200 Subject: [PATCH] Fix Anycubic Kossel config (probe crash) (#11832) --- .../src/config/examples/delta/Anycubic/Kossel/Configuration.h | 4 ++-- .../config/examples/delta/Anycubic/Kossel/Configuration_adv.h | 2 +- Marlin/src/config/examples/delta/Anycubic/Kossel/README.md | 3 ++- 3 files changed, 5 insertions(+), 4 deletions(-) diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h index 44234526c1..ac9d98a408 100644 --- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -1017,8 +1017,8 @@ * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. */ #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow -#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points -#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +#define Z_CLEARANCE_BETWEEN_PROBES 25 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 25 // Z Clearance between multiple probes #define Z_AFTER_PROBING 30 // Z position after probing is done #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 52586bb7cc..b01c342b41 100644 --- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -237,7 +237,7 @@ * Multiple extruders can be assigned to the same pin in which case * the fan will turn on when any selected extruder is above the threshold. */ -#define E0_AUTO_FAN_PIN ORIG_E0_AUTO_FAN_PIN +//#define E0_AUTO_FAN_PIN -1 #define E1_AUTO_FAN_PIN -1 #define E2_AUTO_FAN_PIN -1 #define E3_AUTO_FAN_PIN -1 diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/README.md b/Marlin/src/config/examples/delta/Anycubic/Kossel/README.md index f27d0ada64..e5caf6dd88 100644 --- a/Marlin/src/config/examples/delta/Anycubic/Kossel/README.md +++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/README.md @@ -8,13 +8,14 @@ These configurations activate many of the new advanced features of the Marlin fi **Important**: Before doing anything else after updating the firmware, go to `Configuration > Advanced Settings > Initialize EEPROM` to get rid of old configurations. +Then you should execute `Configuration > Delta Calibration > Set Delta Height` and also run `Configuration > Delta Configuration > Probe Z-offset` to verify the Probe offset. + After that you should connect the Z-Probe and start `Configuration > Delta Calibration > Auto Calibration`. When it's done don't forget to also do `Configuration > Delta Calibration > Store Settings` to make it permanent. You should also do a `Motion > Bed Leveling > Level bed` followed by `Store Settings` to ensure a perfect leveling. Please do a manual paper test (moving the nozzle slowly down to Z0 and checking with a piece of paper). If it's not perfect, use `Configuration > Advanced Settings > Probe Z Offset` to correct the difference and execute the calibration again. -**Also Important**: if you value your Z-Probe do NOT execute `Configuration > Delta Configuration > Probe Z-offset` - This can destroy the Z-Probe, see issue [#11337](https://github.com/MarlinFirmware/Marlin/issues/11337). # Select the Configuration