From b97bb14a7ae709f8c2cfc14e98401700ef1d4d76 Mon Sep 17 00:00:00 2001 From: Tanguy Pruvot Date: Mon, 2 Sep 2019 09:37:50 +0200 Subject: [PATCH] Full-featured Alfawise U20 config (#15131) --- .../Alfawise/U20-bltouch/Configuration_adv.h | 57 ++++++++++--------- .../examples/Alfawise/U20/Configuration_adv.h | 6 +- 2 files changed, 34 insertions(+), 29 deletions(-) diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index 9741b3e8d0..81eb541038 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -137,8 +137,8 @@ * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) - #define THERMAL_PROTECTION_PERIOD 40 // Seconds - #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + #define THERMAL_PROTECTION_PERIOD 60 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) @@ -157,7 +157,7 @@ * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set * below 2. */ - #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_PERIOD 60 // Seconds #define WATCH_TEMP_INCREASE 2 // Degrees Celsius #endif @@ -518,7 +518,7 @@ #define X_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5 #define Z_HOME_BUMP_MM 2 -#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define HOMING_BUMP_DIVISOR { 4, 4, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) //#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially //#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing @@ -543,6 +543,7 @@ * * Settings for all BLTouch and clone probes: */ + #undef PROBE_MANUALLY // Safety: The probe needs time to recognize the command. // Minimum command delay (ms). Enable and increase if needed. @@ -591,7 +592,7 @@ //#define BLTOUCH_HS_MODE // Safety: Enable voltage mode settings in the LCD menu. - //#define BLTOUCH_LCD_VOLTAGE_MENU + #define BLTOUCH_LCD_VOLTAGE_MENU #endif // BLTOUCH @@ -854,7 +855,7 @@ #if HAS_LCD_MENU // Include a page of printer information in the LCD Main Menu - //#define LCD_INFO_MENU + #define LCD_INFO_MENU #if ENABLED(LCD_INFO_MENU) //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages #endif @@ -891,7 +892,7 @@ //#define LCD_TIMEOUT_TO_STATUS 15000 // Add an 'M73' G-code to set the current percentage -//#define LCD_SET_PROGRESS_MANUALLY +#define LCD_SET_PROGRESS_MANUALLY #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing @@ -922,7 +923,7 @@ #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing - //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + #define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") @@ -934,7 +935,7 @@ * an option on the LCD screen to continue the print from the last-known * point in the file. */ - //#define POWER_LOSS_RECOVERY + #define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -945,6 +946,9 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + //#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output + //#define SAVE_INFO_INTERVAL_MS 0 // Force SD recov. write interval, on each layer start if 0 #endif /** @@ -970,7 +974,7 @@ * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) */ - //#define SDCARD_SORT_ALPHA + #define SDCARD_SORT_ALPHA // SD Card Sorting options #if ENABLED(SDCARD_SORT_ALPHA) @@ -986,7 +990,7 @@ #endif // This allows hosts to request long names for files and folders with M33 - //#define LONG_FILENAME_HOST_SUPPORT + #define LONG_FILENAME_HOST_SUPPORT // Enable this option to scroll long filenames in the SD card menu //#define SCROLL_LONG_FILENAMES @@ -1006,7 +1010,7 @@ * On print completion the LCD Menu will open with the file selected. * You can just click to start the print, or navigate elsewhere. */ - //#define SD_REPRINT_LAST_SELECTED_FILE + #define SD_REPRINT_LAST_SELECTED_FILE /** * Auto-report SdCard status with M27 S @@ -1099,7 +1103,7 @@ */ #if HAS_GRAPHICAL_LCD // Show SD percentage next to the progress bar - //#define DOGM_SD_PERCENT + #define DOGM_SD_PERCENT // Enable to save many cycles by drawing a hollow frame on the Info Screen #define XYZ_HOLLOW_FRAME @@ -1155,7 +1159,7 @@ //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames - //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + #define STATUS_HEAT_PERCENT // Show heating in a progress bar //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM. @@ -1218,12 +1222,13 @@ // FSMC Graphical TFT // #if ENABLED(FSMC_GRAPHICAL_TFT) - //#define TFT_MARLINUI_COLOR 0xFFFF // White - //#define TFT_MARLINBG_COLOR 0x0000 // Black - //#define TFT_DISABLED_COLOR 0x0003 // Almost black - //#define TFT_BTCANCEL_COLOR 0xF800 // Red - //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow - //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan + // see https://ee-programming-notepad.blogspot.com/2016/10/16-bit-color-generator-picker.html + #define TFT_MARLINUI_COLOR COLOR_WHITE + #define TFT_MARLINBG_COLOR COLOR_BLACK + #define TFT_DISABLED_COLOR 0x10A2 // almost black + #define TFT_BTCANCEL_COLOR COLOR_RED + #define TFT_BTARROWS_COLOR COLOR_WHITE + #define TFT_BTOKMENU_COLOR COLOR_BLUE #endif // @section safety @@ -1420,16 +1425,16 @@ // The number of linear motions that can be in the plan at any give time. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. #if ENABLED(SDSUPPORT) - #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller + #define BLOCK_BUFFER_SIZE 32 #else - #define BLOCK_BUFFER_SIZE 16 // maximize block buffer + #define BLOCK_BUFFER_SIZE 16 // Marlin default #endif // @section serial // The ASCII buffer for serial input #define MAX_CMD_SIZE 96 -#define BUFSIZE 4 +#define BUFSIZE 8 // Transmission to Host Buffer Size // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. @@ -1569,7 +1574,7 @@ * Requires NOZZLE_PARK_FEATURE. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. @@ -1590,7 +1595,7 @@ // For direct drive, the full length of the nozzle. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. - #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + #define ADVANCED_PAUSE_PURGE_LENGTH 25 // (mm) Length to extrude after loading. // Set to 0 for manual extrusion. // Filament can be extruded repeatedly from the Filament Change menu // until extrusion is consistent, and to purge old filament. @@ -1609,7 +1614,7 @@ //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change - //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) #endif diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index a3ff7aafd7..aff481528c 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -922,7 +922,7 @@ #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing - #define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + #define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") @@ -1424,9 +1424,9 @@ // The number of linear motions that can be in the plan at any give time. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. #if ENABLED(SDSUPPORT) - #define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller + #define BLOCK_BUFFER_SIZE 32 #else - #define BLOCK_BUFFER_SIZE 16 // maximize block buffer + #define BLOCK_BUFFER_SIZE 16 // Marlin default #endif // @section serial