diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 85f5b44be1..0e7982ffa3 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h
index 85f5b44be1..0e7982ffa3 100644
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index bce1ff3db2..aa902de8fc 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index 0b963b3722..bdd7c78ef5 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index f393048ec7..fdb5c7e4d2 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index 85f5b44be1..0e7982ffa3 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index f38d8b76ae..ab33450241 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
index fa509e54ad..1f1db2f90e 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index e1493a6ccb..0e00da5260 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 683d9c269c..405dd72b53 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index e1493a6ccb..0e00da5260 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index ab6ec2567d..eaa3be19e2 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index c30f536e72..cad97f989f 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index 6cbf7b91fd..0fb10d6898 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
index 211b4db7bf..e7d551306e 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
index 12ed30859e..65b720c1e9 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
index 91e17965f0..1cea80018d 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
index 48b4130138..d298c00df1 100644
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
index 12ed30859e..65b720c1e9 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index adec3b6e47..7a212cb745 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 2aac4237ba..02021ae6f8 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index a8fbd555a2..1679f96817 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index a8fbd555a2..1679f96817 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index 098fba4935..0c785128c1 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index 9ed56ce2ab..d50735fa8d 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index 47b338729e..288a689af5 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index a843493801..5e53f5ad58 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index a1544221e4..8ee5b2fe99 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 88824de1f2..3514dcddba 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index 26785040c8..dddca81c2e 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index aa9245918e..d9435dffb4 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index 7634664ba2..9915a6e6d4 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index ec6d972e07..22f18730c7 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index e1b318b866..9614024a32 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index 4783d4194d..74f9453796 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 7c35e0cf8a..00cbefd5f6 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 88db0fd1fd..970f3dd56d 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index c912a74eb5..521d56257b 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 98285a3180..aae07edfb4 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index bad67557cd..bd94fb40dc 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index f7a71e89dd..dcc975e446 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index f7a71e89dd..dcc975e446 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index f7a71e89dd..dcc975e446 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index d6da4a3429..c5890f22e8 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -213,10 +213,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index d3b4a14f77..489470ede9 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 8ff19795ce..9c134971d4 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index fb215eb389..3f37a65126 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index 6d82b1aaac..ac578a43d8 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index 299eac9ac0..cbd6aeea0f 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -208,10 +208,20 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
-// This defines the minimal speed for the main fan, run in PWM mode
-// to enable uncomment and set minimal PWM speed for reliable running (1-255)
-// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+/**
+ * PWM Fan Scaling
+ *
+ * Define the min/max speeds for PWM fans (as set with M106).
+ *
+ * With these options the M106 0-255 value range is scaled to a subset
+ * to ensure that the fan has enough power to spin, or to run lower
+ * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
+ * Value 0 always turns off the fan.
+ *
+ * Define one or both of these to override the default 0-255 range.
+ */
 //#define FAN_MIN_PWM 50
+//#define FAN_MAX_PWM 128
 
 // @section extruder
 
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index 02531b3edc..a57f34d84e 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -979,6 +979,23 @@
  */
 #define HAS_FANMUX PIN_EXISTS(FANMUX0)
 
+/**
+ * MIN/MAX fan PWM scaling
+ */
+#ifndef FAN_MIN_PWM
+  #define FAN_MIN_PWM 0
+#endif
+#ifndef FAN_MAX_PWM
+  #define FAN_MAX_PWM 255
+#endif
+#if FAN_MIN_PWM < 0 || FAN_MIN_PWM > 255
+  #error "FAN_MIN_PWM must be a value from 0 to 255."
+#elif FAN_MAX_PWM < 0 || FAN_MAX_PWM > 255
+  #error "FAN_MAX_PWM must be a value from 0 to 255."
+#elif FAN_MIN_PWM > FAN_MAX_PWM
+  #error "FAN_MIN_PWM must be less than or equal to FAN_MAX_PWM."
+#endif
+
 /**
  * Bed Probe dependencies
  */
diff --git a/Marlin/src/module/planner.cpp b/Marlin/src/module/planner.cpp
index a8da978c85..e1f5f10238 100644
--- a/Marlin/src/module/planner.cpp
+++ b/Marlin/src/module/planner.cpp
@@ -1108,8 +1108,8 @@ void Planner::check_axes_activity() {
 
     #endif // FAN_KICKSTART_TIME > 0
 
-    #ifdef FAN_MIN_PWM
-      #define CALC_FAN_SPEED(f) (tail_fan_speed[f] ? ( FAN_MIN_PWM + (tail_fan_speed[f] * (255 - FAN_MIN_PWM)) / 255 ) : 0)
+    #if FAN_MIN_PWM != 0 || FAN_MAX_PWM != 255
+      #define CALC_FAN_SPEED(f) (tail_fan_speed[f] ? map(tail_fan_speed[f], 1, 255, FAN_MIN_PWM, FAN_MAX_PWM) : 0)
     #else
       #define CALC_FAN_SPEED(f) tail_fan_speed[f]
     #endif