From b6051efe5b13052aa7654269c8bf8c4f5fed03d5 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Fri, 10 Jul 2020 01:27:10 -0500 Subject: [PATCH] Capitalize "G-code" --- Marlin/Configuration.h | 2 +- Marlin/Configuration_adv.h | 8 ++++---- 2 files changed, 5 insertions(+), 5 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 2d50a9f8b2..1148458616 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -2213,7 +2213,7 @@ // then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) //#define TEMP_STAT_LEDS -// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +// SkeinForge sends the wrong arc G-codes when using Arc Point as fillet procedure //#define SF_ARC_FIX // Support for the BariCUDA Paste Extruder diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index e102cb4113..b587495058 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -1186,7 +1186,7 @@ #if ENABLED(SDCARD_SORT_ALPHA) #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. #define FOLDER_SORTING -1 // -1=above 0=none 1=below - #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 G-code. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. @@ -2424,7 +2424,7 @@ * for error conditions like overtemperature and short to ground. * To manage over-temp Marlin can decrease the driver current until the error condition clears. * Other detected conditions can be used to stop the current print. - * Relevant g-codes: + * Relevant G-codes: * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. * M911 - Report stepper driver overtemperature pre-warn condition. * M912 - Clear stepper driver overtemperature pre-warn condition flag. @@ -2715,7 +2715,7 @@ * Monitor L6470 drivers for error conditions like over temperature and over current. * In the case of over temperature Marlin can decrease the drive until the error condition clears. * Other detected conditions can be used to stop the current print. - * Relevant g-codes: + * Relevant G-codes: * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. * I not present or I0 or I1 - X, Y, Z or E0 * I2 - X2, Y2, Z2 or E1 @@ -3029,7 +3029,7 @@ //#define POWER_MONITOR_VOLTAGE // Monitor the system voltage #if EITHER(POWER_MONITOR_CURRENT, POWER_MONITOR_VOLTAGE) #define POWER_MONITOR_VOLTS_PER_AMP 0.05000 // Input voltage to the MCU analog pin per amp - DO NOT apply more than ADC_VREF! - #define POWER_MONITOR_CURRENT_OFFSET -1 // Offset value for current sensors with linear function output + #define POWER_MONITOR_CURRENT_OFFSET -1 // Offset value for current sensors with linear function output #define POWER_MONITOR_VOLTS_PER_VOLT 0.11786 // Input voltage to the MCU analog pin per volt - DO NOT apply more than ADC_VREF! #define POWER_MONITOR_FIXED_VOLTAGE 13.6 // Voltage for a current sensor with no voltage sensor (for power display) #endif